Merge branch 'master' of git://git.denx.de/u-boot-arm

9 files changed, 122 insertions, 5 deletions

diff --git a/include/configs/ap325rxa.h b/include/configs/ap325rxa.h
index 70dd47e..80a5797 100644
--- a/include/configs/ap325rxa.h
+++ b/include/configs/ap325rxa.h
@@ -138,6 +138,7 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0x200	/* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET	0x200	/* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0x210	/* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 
 /* if you use all NOR Flash , you change dip-switch. Please see Manual. */
 #define CONFIG_SYS_MAX_FLASH_BANKS	1
diff --git a/include/configs/edminiv2.h b/include/configs/edminiv2.h
index 055931c..57dd165 100644
--- a/include/configs/edminiv2.h
+++ b/include/configs/edminiv2.h
@@ -60,7 +60,7 @@
 
 #define ORION5X_MPP0_7		0x00000003
 #define ORION5X_MPP8_15		0x55550000
-#define ORION5X_MPP16_23	0x00000000
+#define ORION5X_MPP16_23	0x00005555
 
 /*
  * Board-specific values for Orion5x GPIO low level init:
@@ -131,6 +131,7 @@
  * Commands configuration - using default command set for now
  */
 #include <config_cmd_default.h>
+#define CONFIG_CMD_IDE
 
 /*
  * Network
@@ -150,6 +151,37 @@
 #endif
 
 /*
+ * IDE
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_IDE_PREINIT
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+/* ED Mini V has an IDE-compatible SATA connector for port 1 */
+#define CONFIG_MVSATA_IDE
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE		4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* A single bus, a single device */
+#define CONFIG_SYS_IDE_MAXBUS		1
+#define CONFIG_SYS_IDE_MAXDEVICE	1
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR	ORION5X_SATA_BASE
+/* ATA bus 0 is orion5x port 1 on ED Mini V2 */
+#define CONFIG_SYS_ATA_IDE0_OFFSET	ORION5X_SATA_PORT1_OFFSET
+/* end of IDE defines */
+#endif /* CMD_IDE */
+
+/*
  *  Environment variables configurations
  */
 #define CONFIG_ENV_IS_IN_FLASH		1
diff --git a/include/configs/ms7720se.h b/include/configs/ms7720se.h
index ba0a3f8..0ea3527 100644
--- a/include/configs/ms7720se.h
+++ b/include/configs/ms7720se.h
@@ -122,5 +122,6 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0		/* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET	0		/* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0x200		/* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 
 #endif	/* __MS7720SE_H */
diff --git a/include/configs/omap4_panda.h b/include/configs/omap4_panda.h
index b1e40a3..a0d27a4 100644
--- a/include/configs/omap4_panda.h
+++ b/include/configs/omap4_panda.h
@@ -35,6 +35,7 @@
 #define CONFIG_OMAP44XX		1	/* which is a 44XX */
 #define CONFIG_OMAP4430		1	/* which is in a 4430 */
 #define CONFIG_PANDA		1	/* working with Panda */
+#define CONFIG_ARCH_CPU_INIT
 
 /* Get CPU defs */
 #include <asm/arch/cpu.h>
@@ -102,12 +103,29 @@
 #define CONFIG_DRIVER_OMAP34XX_I2C	1
 #define CONFIG_I2C_MULTI_BUS		1
 
+/* TWL6030 */
+#define CONFIG_TWL6030_POWER		1
+
 /* MMC */
 #define CONFIG_MMC			1
 #define CONFIG_OMAP3_MMC		1
 #define CONFIG_SYS_MMC_SET_DEV		1
 #define CONFIG_DOS_PARTITION		1
 
+/* USB */
+#define CONFIG_MUSB_UDC			1
+#define CONFIG_USB_OMAP3		1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE		1
+#define CONFIG_USB_TTY			1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID		0x0451
+#define CONFIG_USBD_PRODUCTID		0x5678
+#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME	"OMAP4 Panda"
+
 /* Flash */
 #define CONFIG_SYS_NO_FLASH	1
 
@@ -135,16 +153,21 @@
  * Environment setup
  */
 
+#define CONFIG_BOOTDELAY	3
+
 /* allow overwriting serial config and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x82000000\0" \
 	"console=ttyS2,115200n8\0" \
+	"usbtty=cdc_acm\0" \
+	"vram=16M\0" \
 	"mmcdev=1\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"mmcargs=setenv bootargs console=${console} " \
+		"vram=${vram} " \
 		"root=${mmcroot} " \
 		"rootfstype=${mmcrootfstype}\0" \
 	"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
@@ -162,7 +185,6 @@
 		"else " \
 			"if run loaduimage; then " \
 				"run mmcboot; " \
-			"else run nandboot; " \
 			"fi; " \
 		"fi; " \
 	"fi"
@@ -195,7 +217,7 @@
 #define CONFIG_SYS_LOAD_ADDR		0x80000000
 
 /* Use General purpose timer 1 */
-#define CONFIG_SYS_TIMERBASE		GPT1_BASE
+#define CONFIG_SYS_TIMERBASE		GPT2_BASE
 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
 #define CONFIG_SYS_HZ			1000
 
diff --git a/include/configs/omap4_sdp4430.h b/include/configs/omap4_sdp4430.h
index 8121554..d5439f9 100644
--- a/include/configs/omap4_sdp4430.h
+++ b/include/configs/omap4_sdp4430.h
@@ -36,6 +36,7 @@
 #define CONFIG_OMAP44XX		1	/* which is a 44XX */
 #define CONFIG_OMAP4430		1	/* which is in a 4430 */
 #define CONFIG_4430SDP		1	/* working with SDP */
+#define CONFIG_ARCH_CPU_INIT
 
 /* Get CPU defs */
 #include <asm/arch/cpu.h>
@@ -103,12 +104,29 @@
 #define CONFIG_DRIVER_OMAP34XX_I2C	1
 #define CONFIG_I2C_MULTI_BUS		1
 
+/* TWL6030 */
+#define CONFIG_TWL6030_POWER		1
+
 /* MMC */
 #define CONFIG_MMC			1
 #define CONFIG_OMAP3_MMC		1
 #define CONFIG_SYS_MMC_SET_DEV		1
 #define CONFIG_DOS_PARTITION		1
 
+/* USB */
+#define CONFIG_MUSB_UDC			1
+#define CONFIG_USB_OMAP3		1
+
+/* USB device configuration */
+#define CONFIG_USB_DEVICE		1
+#define CONFIG_USB_TTY			1
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	1
+/* Change these to suit your needs */
+#define CONFIG_USBD_VENDORID		0x0451
+#define CONFIG_USBD_PRODUCTID		0x5678
+#define CONFIG_USBD_MANUFACTURER	"Texas Instruments"
+#define CONFIG_USBD_PRODUCT_NAME	"SDP4430"
+
 /* Flash */
 #define CONFIG_SYS_NO_FLASH	1
 
@@ -136,16 +154,21 @@
  * Environment setup
  */
 
+#define CONFIG_BOOTDELAY	3
+
 /* allow overwriting serial config and ethaddr */
 #define CONFIG_ENV_OVERWRITE
 
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	"loadaddr=0x82000000\0" \
 	"console=ttyS2,115200n8\0" \
+	"usbtty=cdc_acm\0" \
+	"vram=16M\0" \
 	"mmcdev=1\0" \
 	"mmcroot=/dev/mmcblk0p2 rw\0" \
 	"mmcrootfstype=ext3 rootwait\0" \
 	"mmcargs=setenv bootargs console=${console} " \
+		"vram=${vram} " \
 		"root=${mmcroot} " \
 		"rootfstype=${mmcrootfstype}\0" \
 	"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
@@ -163,7 +186,6 @@
 		"else " \
 			"if run loaduimage; then " \
 				"run mmcboot; " \
-			"else run nandboot; " \
 			"fi; " \
 		"fi; " \
 	"fi"
@@ -196,7 +218,7 @@
 #define CONFIG_SYS_LOAD_ADDR		0x80000000
 
 /* Use General purpose timer 1 */
-#define CONFIG_SYS_TIMERBASE		GPT1_BASE
+#define CONFIG_SYS_TIMERBASE		GPT2_BASE
 #define CONFIG_SYS_PTV			2	/* Divisor: 2^(PTV+1) => 8 */
 #define CONFIG_SYS_HZ			1000
 
diff --git a/include/configs/openrd_base.h b/include/configs/openrd_base.h
index 52fa73d..846dfcd 100644
--- a/include/configs/openrd_base.h
+++ b/include/configs/openrd_base.h
@@ -103,6 +103,7 @@
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_USB
+#define CONFIG_CMD_IDE
 
 /*
  * NAND configuration
@@ -205,6 +206,36 @@
 #endif /* CONFIG_CMD_USB */
 
 /*
+ * IDe Support on SATA port0
+ */
+#ifdef CONFIG_CMD_IDE
+#define __io
+#define CONFIG_CMD_EXT2
+#define CONFIG_MVSATA_IDE
+#define CONFIG_IDE_PREINIT
+#define CONFIG_MVSATA_IDE_USE_PORT1
+/* Needs byte-swapping for ATA data register */
+#define CONFIG_IDE_SWAP_IO
+/* Data, registers and alternate blocks are at the same offset */
+#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_REG_OFFSET	(0x0100)
+#define CONFIG_SYS_ATA_ALT_OFFSET	(0x0100)
+/* Each 8-bit ATA register is aligned to a 4-bytes address */
+#define CONFIG_SYS_ATA_STRIDE		4
+/* Controller supports 48-bits LBA addressing */
+#define CONFIG_LBA48
+/* CONFIG_CMD_IDE requires some #defines for ATA registers */
+#define CONFIG_SYS_IDE_MAXBUS		2
+#define CONFIG_SYS_IDE_MAXDEVICE	2
+/* ATA registers base is at SATA controller base */
+#define CONFIG_SYS_ATA_BASE_ADDR	KW_SATA_BASE
+/* ATA bus 0 is Kirkwood port 0 on openrd */
+#define CONFIG_SYS_ATA_IDE0_OFFSET	KW_SATA_PORT0_OFFSET
+/* ATA bus 1 is Kirkwood port 1 on openrd */
+#define CONFIG_SYS_ATA_IDE1_OFFSET	KW_SATA_PORT1_OFFSET
+#endif /* CONFIG_CMD_IDE */
+
+/*
  * File system
  */
 #define CONFIG_CMD_FAT
diff --git a/include/configs/r2dplus.h b/include/configs/r2dplus.h
index 8931b97..955f3ff 100644
--- a/include/configs/r2dplus.h
+++ b/include/configs/r2dplus.h
@@ -96,6 +96,7 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET	0x1000	/* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET	0x1000	/* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0x800	/* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 
 /*
  * SuperH PCI Bridge Configration
diff --git a/include/configs/r7780mp.h b/include/configs/r7780mp.h
index 71c570e..3afe93a 100644
--- a/include/configs/r7780mp.h
+++ b/include/configs/r7780mp.h
@@ -171,6 +171,7 @@
 #define CONFIG_SYS_ATA_DATA_OFFSET     0x1000          /* data reg offset */
 #define CONFIG_SYS_ATA_REG_OFFSET      0x1000          /* reg offset */
 #define CONFIG_SYS_ATA_ALT_OFFSET      0x800           /* alternate register offset */
+#define CONFIG_IDE_SWAP_IO
 #endif /* CONFIG_CMD_IDE */
 
 #endif /* __R7780RP_H */
diff --git a/include/configs/s5p_goni.h b/include/configs/s5p_goni.h
index ff0dbd3..c8ea8fd 100644
--- a/include/configs/s5p_goni.h
+++ b/include/configs/s5p_goni.h
@@ -67,6 +67,11 @@
 #define CONFIG_SERIAL_MULTI		1
 #define CONFIG_BAUDRATE			115200
 
+/* MMC */
+#define CONFIG_GENERIC_MMC		1
+#define CONFIG_MMC			1
+#define CONFIG_S5P_MMC			1
+
 /* It should define before config_cmd_default.h */
 #define CONFIG_SYS_NO_FLASH		1
 
@@ -82,6 +87,7 @@
 #define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_ONENAND
 #define CONFIG_CMD_MTDPARTS
+#define CONFIG_CMD_MMC
 
 #define CONFIG_BOOTDELAY		1
 #define CONFIG_ZERO_BOOTDELAY_CHECK