Merge git://www.denx.de/git/u-boot

64 files changed, 2271 insertions, 530 deletions

diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h
index 9e0ee37..0718c85 100644
--- a/include/configs/ASH405.h
+++ b/include/configs/ASH405.h
@@ -53,9 +53,13 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
+#define CONFIG_NET_MULTI	1
+#undef  CONFIG_HAS_ETH1
+
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address			*/
 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
+#define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
 
 #define CONFIG_PHY_CLK_FREQ	EMAC_STACR_CLK_66MHZ /* 66 MHz OPB clock*/
 
@@ -144,39 +148,16 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
 
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1  /* verify all writes!!!         */
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
 /*-----------------------------------------------------------------------
diff --git a/include/configs/CMS700.h b/include/configs/CMS700.h
index 08ef9b5..1fd2b53 100644
--- a/include/configs/CMS700.h
+++ b/include/configs/CMS700.h
@@ -90,8 +90,6 @@
 #define CONFIG_CMD_EEPROM
 
 
-#define CFG_NAND_LEGACY
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
@@ -157,34 +155,15 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
diff --git a/include/configs/CPCI405.h b/include/configs/CPCI405.h
index 0a4e1e9..1b948f6 100644
--- a/include/configs/CPCI405.h
+++ b/include/configs/CPCI405.h
@@ -92,8 +92,6 @@
 
 #define CONFIG_SUPPORT_VFAT
 
-#define CFG_NAND_LEGACY
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h
index ceeba6e..fb71c5f 100644
--- a/include/configs/CPCI4052.h
+++ b/include/configs/CPCI4052.h
@@ -114,8 +114,6 @@
 #define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
 #endif
 
-#define CFG_NAND_LEGACY
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h
index 1aefbba..4994319 100644
--- a/include/configs/CPCI405AB.h
+++ b/include/configs/CPCI405AB.h
@@ -100,9 +100,6 @@
 
 #define CONFIG_SUPPORT_VFAT
 
-#define CFG_NAND_LEGACY
-
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h
index e2652e6..29f9292 100644
--- a/include/configs/CPCI405DT.h
+++ b/include/configs/CPCI405DT.h
@@ -111,8 +111,6 @@
 
 #undef  CONFIG_AUTO_UPDATE              /* autoupdate via compactflash  */
 
-#define CFG_NAND_LEGACY
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
diff --git a/include/configs/EB+MCF-EV123.h b/include/configs/EB+MCF-EV123.h
index a8697ec..dae5295 100644
--- a/include/configs/EB+MCF-EV123.h
+++ b/include/configs/EB+MCF-EV123.h
@@ -40,9 +40,8 @@
 
 #define CONFIG_MISC_INIT_R
 
-#define FEC_ENET
-#define CONFIG_ETHADDR 00:CF:52:82:EB:01
-
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE 9600
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
@@ -84,7 +83,39 @@
 #include <config_cmd_default.h>
 
 #undef CONFIG_CMD_LOADB
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:CF:52:82:EB:01
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* CONFIG_MCFFEC */
 
 #define CONFIG_BOOTDELAY	5
 #define CFG_PROMPT		"\nEV123 U-Boot> "
@@ -122,9 +153,6 @@
  */
 #define	CFG_MBAR		0x40000000
 
-#define	CFG_DISCOVER_PHY
-/* #define	CFG_ENET_BD_BASE	0x380000 */
-
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
@@ -151,6 +179,7 @@
 
 #define CFG_FLASH_BASE		0xFFE00000
 #define	CFG_INT_FLASH_BASE	0xF0000000
+#define CFG_INT_FLASH_ENABLE	0x21
 
 /* If M5282 port is fully implemented the monitor base will be behind
  * the vector table. */
diff --git a/include/configs/HH405.h b/include/configs/HH405.h
index 00f481c..ea8e61a 100644
--- a/include/configs/HH405.h
+++ b/include/configs/HH405.h
@@ -141,8 +141,6 @@
 #define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
 #undef CONFIG_AUTO_UPDATE_SHOW          /* use board show routine       */
 
-#define CFG_NAND_LEGACY
-
 #undef  CONFIG_BZIP2	 /* include support for bzip2 compressed images */
 #undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -209,34 +207,15 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN 	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)  /* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)  /* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)  /* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)  /* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
diff --git a/include/configs/HUB405.h b/include/configs/HUB405.h
index 661b895..ed669c5 100644
--- a/include/configs/HUB405.h
+++ b/include/configs/HUB405.h
@@ -147,36 +147,15 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h
index 53261548..4c16d22 100644
--- a/include/configs/IceCube.h
+++ b/include/configs/IceCube.h
@@ -178,12 +178,9 @@
 #endif /* CONFIG_MPC5200 */
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
diff --git a/include/configs/M5235EVB.h b/include/configs/M5235EVB.h
new file mode 100644
index 0000000..7f544c8
--- /dev/null
+++ b/include/configs/M5235EVB.h
@@ -0,0 +1,261 @@
+/*
+ * Configuation settings for the Freescale MCF5329 FireEngine board.
+ *
+ * Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5235EVB_H
+#define _M5235EVB_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF523x		/* define processor family */
+#define CONFIG_M5235		/* define processor type */
+
+#undef DEBUG
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
+#define CONFIG_BAUDRATE		115200
+#define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef CONFIG_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT	5000	/* timeout in milliseconds, max timeout is 6.71sec */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/* Command line configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+/* Timer */
+#define CONFIG_MCFTMR
+#undef CONFIG_MCFPIT
+
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C			/* I2C with hw support */
+#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		80000
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_OFFSET		0x00000300
+#define CFG_IMMR		CFG_MBAR
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
+#define CONFIG_BOOTFILE		"u-boot.bin"
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* FEC_ENET */
+
+#define CONFIG_HOSTNAME		M5235EVB
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe3ffff;"	\
+	"era ffe00000 ffe3ffff;"		\
+	"cp.b ${loadaddr} ffe00000 ${filesize};"\
+	"save\0"				\
+	""
+
+#define CONFIG_PRAM		512	/* 512 KB */
+#define CFG_PROMPT		"-> "
+#define CFG_LONGHELP		/* undef to save memory */
+
+#if defined(CONFIG_KGDB)
+#	define CFG_CBSIZE		1024	/* Console I/O Buffer Size */
+#else
+#	define CFG_CBSIZE		256	/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
+#define CFG_LOAD_ADDR		(CFG_SDRAM_BASE+0x20000)
+
+#define CFG_HZ			1000
+#define CFG_CLK			75000000
+#define CFG_CPU_CLK		CFG_CLK * 2
+
+#define CFG_MBAR		0x40000000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x20000000
+#define CFG_INIT_RAM_END	0x10000	/* End of used area in internal SRAM */
+#define CFG_INIT_RAM_CTRL	0x21
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE - 0x10)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
+
+#define CFG_MEMTEST_START	CFG_SDRAM_BASE + 0x400
+#define CFG_MEMTEST_END		((CFG_SDRAM_SIZE - 3) << 20)
+
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+
+#define CFG_BOOTPARAMS_LEN	64*1024
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x800000	/* Max size that the board might have */
+#ifdef NORFLASH_PS32BIT
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_32BIT
+#else
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#endif
+#	define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#endif
+
+#define CFG_FLASH_BASE		(CFG_CS0_BASE << 16)
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_IS_EMBEDDED	1
+#ifdef NORFLASH_PS32BIT
+#	define CFG_ENV_OFFSET		(0x8000)
+#	define CFG_ENV_SIZE		0x4000
+#	define CFG_ENV_SECT_SIZE	0x4000
+#else
+#	define CFG_ENV_OFFSET		(0x4000)
+#	define CFG_ENV_SIZE		0x2000
+#	define CFG_ENV_SECT_SIZE	0x2000
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16
+
+/*-----------------------------------------------------------------------
+ * Chipselect bank definitions
+ */
+/*
+ * CS0 - NOR Flash 1, 2, 4, or 8MB
+ * CS1 - Available
+ * CS2 - Available
+ * CS3 - Available
+ * CS4 - Available
+ * CS5 - Available
+ * CS6 - Available
+ * CS7 - Available
+ */
+#ifdef NORFLASH_PS32BIT
+#	define CFG_CS0_BASE	0xFFC0
+#	define CFG_CS0_MASK	0x003f0001
+#	define CFG_CS0_CTRL	0x1D00
+#else
+#	define CFG_CS0_BASE	0xFFE0
+#	define CFG_CS0_MASK	0x001f0001
+#	define CFG_CS0_CTRL	0x1D80
+#endif
+
+#endif				/* _M5329EVB_H */
diff --git a/include/configs/M5249EVB.h b/include/configs/M5249EVB.h
new file mode 100644
index 0000000..de7ea42
--- /dev/null
+++ b/include/configs/M5249EVB.h
@@ -0,0 +1,194 @@
+/*
+ * Configuation settings for the esd TASREG board.
+ *
+ * (C) Copyright 2004
+ * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5249EVB_H
+#define _M5249EVB_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF52x2			/* define processor family */
+#define CONFIG_M5249			/* define processor type */
+
+#define CONFIG_MCFTMR
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
+#define CONFIG_BAUDRATE		19200
+#define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef  CONFIG_WATCHDOG
+
+#undef CONFIG_MONITOR_IS_IN_RAM		/* no pre-loader required!!! ;-) */
+
+/*
+ * BOOTP options
+ */
+#undef CONFIG_BOOTP_BOOTFILESIZE
+#undef CONFIG_BOOTP_BOOTPATH
+#undef CONFIG_BOOTP_GATEWAY
+#undef CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_NET
+
+#define CFG_PROMPT		"=> "
+#define CFG_LONGHELP				/* undef to save memory		*/
+
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup	*/
+#define CONFIG_AUTO_COMPLETE	1	/* add autocompletion support	*/
+#define CONFIG_LOOPW		1	/* enable loopw command	*/
+#define CONFIG_MX_CYCLIC	1	/* enable mdc/mwc commands	*/
+
+#define CFG_LOAD_ADDR		0x200000	/* default load address */
+
+#define CFG_MEMTEST_START	0x400
+#define CFG_MEMTEST_END		0x380000
+
+#define CFG_HZ			1000
+
+/*
+ * Clock configuration: enable only one of the following options
+ */
+
+#undef  CFG_PLL_BYPASS				/* bypass PLL for test purpose */
+#define CFG_FAST_CLK		1		/* MCF5249 can run at 140MHz   */
+#define	CFG_CLK			132025600	/* MCF5249 can run at 140MHz   */
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+#define CFG_MBAR		0x10000000	/* Register Base Addrs */
+#define	CFG_MBAR2		0x80000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x20000000
+#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM	*/
+#define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		0x4000	/* Address of Environment Sector*/
+#define CFG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
+#define CFG_ENV_SECT_SIZE	0x2000 /* see README - env sector total size	*/
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_SIZE		16		/* SDRAM size in MB */
+#define CFG_FLASH_BASE		(CFG_CSAR0 << 16)
+
+#if 0 /* test-only */
+#define CONFIG_PRAM		512 /* test-only for SDRAM problem!!!!!!!!!!!!!!!!!!!! */
+#endif
+
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+
+#define CFG_MONITOR_LEN		0x20000
+#define CFG_MALLOC_LEN		(1 * 1024*1024)	/* Reserve 1 MB for malloc()	*/
+#define CFG_BOOTPARAMS_LEN	64*1024
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x1000000	/* Max size that the board might have */
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#	define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#	define CFG_FLASH_CHECKSUM
+#	define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16
+
+/*-----------------------------------------------------------------------
+ * Memory bank definitions
+ */
+
+/* CS0 - AMD Flash, address 0xffc00000 */
+#define	CFG_CSAR0		0xffe0
+#define	CFG_CSCR0		0x1980		/* WS=0110, AA=1, PS=10         */
+/** Note: There is a CSMR0/DRAM vector problem, need to disable C/I ***/
+#define	CFG_CSMR0		0x003f0021	/* 4MB, AA=0, WP=0, C/I=1, V=1  */
+
+/* CS1 - FPGA, address 0xe0000000 */
+#define	CFG_CSAR1		0xe000
+#define	CFG_CSCR1		0x0d80		/* WS=0011, AA=1, PS=10         */
+#define	CFG_CSMR1		0x00010001	/* 128kB, AA=0, WP=0, C/I=0, V=1*/
+
+/*-----------------------------------------------------------------------
+ * Port configuration
+ */
+#define	CFG_GPIO_FUNC		0x00000008	/* Set gpio pins: none          */
+#define	CFG_GPIO1_FUNC		0x00df00f0	/* 36-39(SWITCH),48-52(FPGAs),54*/
+#define	CFG_GPIO_EN		0x00000008	/* Set gpio output enable       */
+#define	CFG_GPIO1_EN		0x00c70000	/* Set gpio output enable       */
+#define	CFG_GPIO_OUT		0x00000008	/* Set outputs to default state */
+#define	CFG_GPIO1_OUT		0x00c70000	/* Set outputs to default state */
+#define CFG_GPIO1_LED		0x00400000	/* user led                     */
+
+#endif	/* M5249 */
diff --git a/include/configs/M5253EVBE.h b/include/configs/M5253EVBE.h
new file mode 100644
index 0000000..48170e7
--- /dev/null
+++ b/include/configs/M5253EVBE.h
@@ -0,0 +1,212 @@
+/*
+ * Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
+ * Hayden Fraser (Hayden.Fraser@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef _M5253EVBE_H
+#define _M5253EVBE_H
+
+#define CONFIG_MCF52x2		/* define processor family */
+#define CONFIG_M5253		/* define processor type */
+#define CONFIG_M5253EVBE	/* define board type */
+
+#define CONFIG_MCFTMR
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
+#define CONFIG_BAUDRATE		19200
+#define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef CONFIG_WATCHDOG		/* disable watchdog */
+
+#define CONFIG_BOOTDELAY	5
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#ifndef CONFIG_MONITOR_IS_IN_RAM
+#define CFG_ENV_OFFSET		0x4000
+#define CFG_ENV_SECT_SIZE	0x2000
+#define CFG_ENV_IS_IN_FLASH	1
+#else
+#define CFG_ENV_ADDR		0xffe04000
+#define CFG_ENV_SECT_SIZE	0x2000
+#define CFG_ENV_IS_IN_FLASH	1
+#endif
+
+/*
+ * BOOTP options
+ */
+#undef CONFIG_BOOTP_BOOTFILESIZE
+#undef CONFIG_BOOTP_BOOTPATH
+#undef CONFIG_BOOTP_GATEWAY
+#undef CONFIG_BOOTP_HOSTNAME
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#undef CONFIG_CMD_NET
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_LOADS
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+
+/* ATA */
+#define CONFIG_DOS_PARTITION
+#define CONFIG_MAC_PARTITION
+#define CONFIG_IDE_RESET	1
+#define CONFIG_IDE_PREINIT	1
+#define CONFIG_ATAPI
+#undef CONFIG_LBA48
+
+#define CFG_IDE_MAXBUS		1
+#define CFG_IDE_MAXDEVICE	2
+
+#define CFG_ATA_BASE_ADDR	(CFG_MBAR2 + 0x800)
+#define CFG_ATA_IDE0_OFFSET	0
+
+#define CFG_ATA_DATA_OFFSET	0xA0	/* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers */
+#define CFG_ATA_STRIDE		4	/* Interval between registers */
+#define _IO_BASE		0
+
+#define CFG_PROMPT		"=> "
+#define CFG_LONGHELP		/* undef to save memory */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+
+#define CFG_LOAD_ADDR		0x00100000
+
+#define CFG_MEMTEST_START	0x400
+#define CFG_MEMTEST_END		0x380000
+
+#define CFG_HZ			1000
+
+#undef CFG_PLL_BYPASS		/* bypass PLL for test purpose */
+#define CFG_FAST_CLK
+#ifdef CFG_FAST_CLK
+#	define CFG_PLLCR	0x1243E054
+#	define CFG_CLK		140000000
+#else
+#	define CFG_PLLCR	0x135a4140
+#	define CFG_CLK		70000000
+#endif
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+#define CFG_MBAR		0x10000000	/* Register Base Addrs */
+#define CFG_MBAR2		0x80000000	/* Module Base Addrs 2 */
+
+/*
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x20000000
+#define CFG_INIT_RAM_END	0x10000	/* End of used area in internal SRAM */
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
+
+#ifdef CONFIG_MONITOR_IS_IN_RAM
+#define CFG_MONITOR_BASE	0x20000
+#else
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#endif
+
+#define CFG_MONITOR_LEN		0x40000
+#define CFG_MALLOC_LEN		(256 << 10)
+#define CFG_BOOTPARAMS_LEN	(64*1024)
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/* FLASH organization */
+#define CFG_FLASH_BASE		0xffe00000
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CFG_MAX_FLASH_SECT	35	/* max number of sectors on one chip */
+#define CFG_FLASH_ERASE_TOUT	1000
+
+#define CFG_FLASH_CFI		1
+#define CFG_FLASH_CFI_DRIVER	1
+#define CFG_FLASH_SIZE		0x200000
+#define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+
+/* Cache Configuration */
+#define CFG_CACHELINE_SIZE	16
+
+/* Port configuration */
+#define CFG_FECI2C		0xF0
+
+#define CFG_CSAR0		0xFFE0
+#define CFG_CSMR0		0x001F0021
+#define CFG_CSCR0		0x1D80
+
+#define CFG_CSAR1		0
+#define CFG_CSMR1		0
+#define CFG_CSCR1		0
+
+#define CFG_CSAR2		0
+#define CFG_CSMR2		0
+#define CFG_CSCR2		0
+
+#define CFG_CSAR3		0
+#define CFG_CSMR3		0
+#define CFG_CSCR3		0
+
+/*-----------------------------------------------------------------------
+ * Port configuration
+ */
+#define CFG_GPIO_FUNC		0x00000008	/* Set gpio pins: none */
+#define CFG_GPIO1_FUNC		0x00df00f0	/* 36-39(SWITCH),48-52(FPGAs),54 */
+#define CFG_GPIO_EN		0x00000008	/* Set gpio output enable */
+#define CFG_GPIO1_EN		0x00c70000	/* Set gpio output enable */
+#define CFG_GPIO_OUT		0x00000008	/* Set outputs to default state */
+#define CFG_GPIO1_OUT		0x00c70000	/* Set outputs to default state */
+#define CFG_GPIO1_LED		0x00400000	/* user led */
+
+#endif				/* _M5253EVB_H */
diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h
index 885a882..0f97050 100644
--- a/include/configs/M5271EVB.h
+++ b/include/configs/M5271EVB.h
@@ -31,7 +31,6 @@
 #ifndef _M5271EVB_H
 #define _M5271EVB_H
 
-#define DEBUG
 #undef DEBUG
 
 /*
@@ -41,17 +40,15 @@
 #define CONFIG_M5271		/* define processor type */
 #define CONFIG_M5271EVB		/* define board type */
 
-#define CONFIG_IPADDR		192.168.30.1
-#define CONFIG_SERVERIP		192.168.1.1
-#define CONFIG_ETHADDR		00:06:3b:01:41:55
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
 
 #undef CONFIG_WATCHDOG		/* disable watchdog */
 
-#define CONFIG_BOOTDELAY	5
-
 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
  */
@@ -73,7 +70,6 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
@@ -81,22 +77,83 @@
 
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
 
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C		/* I2C with hw support */
+#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CFG_I2C_SPEED		80000
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_OFFSET		0x00000300
+#define CFG_IMMR		CFG_MBAR
+
+#define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
+#define CONFIG_BOOTFILE		"u-boot.bin"
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_RETRY_COUNT	5
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* FEC_ENET */
+
+#define CONFIG_HOSTNAME		M5235EVB
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe2ffff;"		\
+	"era ffe00000 ffe2ffff;"				\
+	"cp.b ${loadaddr} 0 ${filesize};"	\
+	"save\0"				\
+	""
 
 #define CFG_PROMPT		"=> "
-#define CFG_LONGHELP				/* undef to save memory		*/
+#define CFG_LONGHELP		/* undef to save memory */
 
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
 
 #define CFG_LOAD_ADDR		0x00100000
 
@@ -114,16 +171,11 @@
 
 #define CFG_MBAR		0x40000000	/* Register Base Addrs */
 
-/* Enable FEC ethernet */
-#define FEC_ENET
-#define CONFIG_NET_RETRY_COUNT	5
-#define CFG_ENET_BD_BASE	0x480000
-
 /*
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	0x20000000
-#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM	*/
+#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM    */
 #define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
@@ -134,7 +186,7 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define CFG_SDRAM_SIZE		16		/* SDRAM size in MB */
+#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
 #define CFG_FLASH_BASE		0xffe00000
 
 #ifdef	CONFIG_MONITOR_IS_IN_RAM
@@ -152,11 +204,11 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /* FLASH organization */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks           */
+#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip    */
 #define CFG_FLASH_ERASE_TOUT	1000
 
 #define CFG_FLASH_CFI		1
@@ -169,4 +221,4 @@
 /* Port configuration */
 #define CFG_FECI2C		0xF0
 
-#endif	/* _M5271EVB_H */
+#endif				/* _M5271EVB_H */
diff --git a/include/configs/M5272C3.h b/include/configs/M5272C3.h
index cc456dc..2b8734b 100644
--- a/include/configs/M5272C3.h
+++ b/include/configs/M5272C3.h
@@ -33,18 +33,20 @@
  * High Level Configuration Options
  * (easy to change)
  */
-#define CONFIG_MCF52x2			/* define processor family */
-#define CONFIG_M5272			/* define processor type */
+#define CONFIG_MCF52x2		/* define processor family */
+#define CONFIG_M5272		/* define processor type */
 
-#define FEC_ENET
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
-#define CONFIG_WATCHDOG
+#undef CONFIG_WATCHDOG
 #define CONFIG_WATCHDOG_TIMEOUT 10000	/* timeout in milliseconds */
 
-#define CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
+#undef CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
 
 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
@@ -60,7 +62,6 @@
 #define CFG_ENV_IS_IN_FLASH	1
 #endif
 
-
 /*
  * BOOTP options
  */
@@ -69,37 +70,82 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
 
 #define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_MEMORY
 
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
-
 #define CONFIG_BOOTDELAY	5
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* CONFIG_MCFFEC */
+
+#define CONFIG_HOSTNAME		M5272C3
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe3ffff;"	\
+	"era ffe00000 ffe3ffff;"		\
+	"cp.b ${loadaddr} ffe00000 ${filesize};"\
+	"save\0"				\
+	""
 
 #define CFG_PROMPT		"-> "
-#define CFG_LONGHELP				/* undef to save memory		*/
+#define CFG_LONGHELP		/* undef to save memory */
 
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
 #define CFG_LOAD_ADDR		0x20000
-
 #define CFG_MEMTEST_START	0x400
 #define CFG_MEMTEST_END		0x380000
-
 #define CFG_HZ			1000
 #define CFG_CLK			66000000
 
@@ -108,20 +154,15 @@
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */
-
 #define CFG_MBAR		0x10000000	/* Register Base Addrs */
-
 #define CFG_SCR			0x0003;
 #define CFG_SPR			0xffff;
 
-#define CFG_DISCOVER_PHY
-#define CFG_ENET_BD_BASE	0x380000
-
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	0x20000000
-#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM	*/
+#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM    */
 #define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
@@ -132,7 +173,7 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define CFG_SDRAM_SIZE		4		/* SDRAM size in MB */
+#define CFG_SDRAM_SIZE		4	/* SDRAM size in MB */
 #define CFG_FLASH_BASE		0xffe00000
 
 #ifdef	CONFIG_MONITOR_IS_IN_RAM
@@ -150,13 +191,13 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks           */
+#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip    */
 #define CFG_FLASH_ERASE_TOUT	1000
 
 /*-----------------------------------------------------------------------
@@ -169,25 +210,18 @@
  */
 #define CFG_BR0_PRELIM		0xFFE00201
 #define CFG_OR0_PRELIM		0xFFE00014
-
 #define CFG_BR1_PRELIM		0
 #define CFG_OR1_PRELIM		0
-
 #define CFG_BR2_PRELIM		0x30000001
 #define CFG_OR2_PRELIM		0xFFF80000
-
 #define CFG_BR3_PRELIM		0
 #define CFG_OR3_PRELIM		0
-
 #define CFG_BR4_PRELIM		0
 #define CFG_OR4_PRELIM		0
-
 #define CFG_BR5_PRELIM		0
 #define CFG_OR5_PRELIM		0
-
 #define CFG_BR6_PRELIM		0
 #define CFG_OR6_PRELIM		0
-
 #define CFG_BR7_PRELIM		0x00000701
 #define CFG_OR7_PRELIM		0xFFC0007C
 
@@ -197,9 +231,8 @@
 #define CFG_PACNT		0x00000000
 #define CFG_PADDR		0x0000
 #define CFG_PADAT		0x0000
-#define CFG_PBCNT		0x55554155		/* Ethernet/UART configuration */
+#define CFG_PBCNT		0x55554155	/* Ethernet/UART configuration */
 #define CFG_PBDDR		0x0000
 #define CFG_PBDAT		0x0000
 #define CFG_PDCNT		0x00000000
-
-#endif	/* _M5272C3_H */
+#endif				/* _M5272C3_H */
diff --git a/include/configs/M5282EVB.h b/include/configs/M5282EVB.h
index f2a7644..3c17c1e 100644
--- a/include/configs/M5282EVB.h
+++ b/include/configs/M5282EVB.h
@@ -33,15 +33,17 @@
  * High Level Configuration Options
  * (easy to change)
  */
-#define	CONFIG_MCF52x2			/* define processor family */
-#define CONFIG_M5282			/* define processor type */
+#define	CONFIG_MCF52x2		/* define processor family */
+#define CONFIG_M5282		/* define processor type */
 
-#define FEC_ENET
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE 19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
-#define	CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
+#undef	CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
 
 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
@@ -50,7 +52,6 @@
 #define CFG_ENV_SIZE		0x2000
 #define CFG_ENV_IS_IN_FLASH	1
 
-
 /*
  * BOOTP options
  */
@@ -59,29 +60,73 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
 
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
 #define CONFIG_BOOTDELAY	5
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* CONFIG_MCFFEC */
+
+#define CONFIG_HOSTNAME		M5272C3
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe3ffff;"	\
+	"era ffe00000 ffe3ffff;"		\
+	"cp.b ${loadaddr} ffe00000 ${filesize};"\
+	"save\0"				\
+	""
 
 #define CFG_PROMPT		"-> "
-#define	CFG_LONGHELP				/* undef to save memory		*/
+#define	CFG_LONGHELP		/* undef to save memory         */
 
 #if defined(CONFIG_CMD_KGDB)
-#define	CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#define	CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
-#define	CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define	CFG_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
-#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define	CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define	CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
 
 #define CFG_LOAD_ADDR		0x20000
 
@@ -91,6 +136,10 @@
 #define CFG_HZ			1000000
 #define	CFG_CLK			64000000
 
+/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */
+
+#define CFG_MFD			0x02	/* PLL Multiplication Factor Devider */
+#define CFG_RFD			0x00	/* PLL Reduce Frecuency Devider */
 
 /*
  * Low Level Configuration Settings
@@ -99,15 +148,12 @@
  */
 #define	CFG_MBAR		0x40000000
 
-#undef	CFG_DISCOVER_PHY
-#define	CFG_ENET_BD_BASE	0x380000
-
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_RAM_ADDR       0x20000000
-#define CFG_INIT_RAM_END	0x10000		/* End of used area in internal SRAM	*/
-#define CFG_GBL_DATA_SIZE	64      	/* size in bytes reserved for initial data */
+#define CFG_INIT_RAM_ADDR	0x20000000
+#define CFG_INIT_RAM_END	0x10000	/* End of used area in internal SRAM    */
+#define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
@@ -117,49 +163,88 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define	CFG_SDRAM_SIZE		4		/* SDRAM size in MB */
+#define	CFG_SDRAM_SIZE		8	/* SDRAM size in MB */
 #define CFG_FLASH_BASE		0xffe00000
 #define	CFG_INT_FLASH_BASE	0xf0000000
+#define CFG_INT_FLASH_ENABLE	0x21
 
 /* If M5282 port is fully implemented the monitor base will be behind
  * the vector table. */
-/* #define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400) */
-#define CFG_MONITOR_BASE	0x20000
+#if (TEXT_BASE != CFG_INT_FLASH_BASE)
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#else
+#define CFG_MONITOR_BASE	(TEXT_BASE + 0x418)	/* 24 Byte for CFM-Config */
+#endif
 
 #define CFG_MONITOR_LEN		0x20000
 #define CFG_MALLOC_LEN		(256 << 10)
 #define CFG_BOOTPARAMS_LEN	64*1024
 
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define	CFG_MAX_FLASH_SECT	35
-#define	CFG_MAX_FLASH_BANKS	1
-#define	CFG_FLASH_ERASE_TOUT	10000000
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x1000000	/* Max size that the board might have */
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#	define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#	define CFG_FLASH_CHECKSUM
+#	define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#endif
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE	16
 
-
 /*-----------------------------------------------------------------------
  * Memory bank definitions
  */
-
-
+#define CFG_CS0_BASE		CFG_FLASH_BASE
+#define CFG_CS0_SIZE		2*1024*1024
+#define CFG_CS0_WIDTH		16
+#define CFG_CS0_RO 		0
+#define CFG_CS0_WS		6
+/*
+#define CFG_CS3_BASE		0xE0000000
+#define CFG_CS3_SIZE		1*1024*1024
+#define CFG_CS3_WIDTH		16
+#define CFG_CS3_RO 		0
+#define CFG_CS3_WS		6
+*/
 /*-----------------------------------------------------------------------
  * Port configuration
  */
+#define CFG_PACNT		0x0000000	/* Port A D[31:24] */
+#define CFG_PADDR		0x0000000
+#define CFG_PADAT		0x0000000
+
+#define CFG_PBCNT		0x0000000	/* Port B D[23:16] */
+#define CFG_PBDDR		0x0000000
+#define CFG_PBDAT		0x0000000
+
+#define CFG_PCCNT		0x0000000	/* Port C D[15:08] */
+#define CFG_PCDDR		0x0000000
+#define CFG_PCDAT		0x0000000
+
+#define CFG_PDCNT		0x0000000	/* Port D D[07:00] */
+#define CFG_PCDDR		0x0000000
+#define CFG_PCDAT		0x0000000
 
+#define CFG_PEHLPAR		0xC0
+#define CFG_PUAPAR		0x0F	/* UA0..UA3 = Uart 0 +1 */
+#define CFG_DDRUA		0x05
+#define CFG_PJPAR 		0xFF;
 
-#endif	/* _CONFIG_M5282EVB_H */
+#endif				/* _CONFIG_M5282EVB_H */
diff --git a/include/configs/M5329EVB.h b/include/configs/M5329EVB.h
new file mode 100644
index 0000000..d3b1605
--- /dev/null
+++ b/include/configs/M5329EVB.h
@@ -0,0 +1,267 @@
+/*
+ * Configuation settings for the Freescale MCF5329 FireEngine board.
+ *
+ * Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _M5329EVB_H
+#define _M5329EVB_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF532x		/* define processor family */
+#define CONFIG_M5329		/* define processor type */
+
+#undef DEBUG
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
+#define CONFIG_BAUDRATE		115200
+#define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef CONFIG_WATCHDOG
+#define CONFIG_WATCHDOG_TIMEOUT	5000	/* timeout in milliseconds, max timeout is 6.71sec */
+
+/* Command line configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+#ifdef NANDFLASH_SIZE
+#      define CONFIG_CMD_NAND
+#endif
+
+#define CFG_UNIFY_CACHE
+
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+#define CONFIG_MCFRTC
+#undef RTC_DEBUG
+
+/* Timer */
+#define CONFIG_MCFTMR
+#undef CONFIG_MCFPIT
+
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C			/* I2C with hw support */
+#undef CONFIG_SOFT_I2C			/* I2C bit-banged */
+#define CFG_I2C_SPEED		80000
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_OFFSET		0x58000
+#define CFG_IMMR		CFG_MBAR
+
+#define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
+#define CONFIG_UDP_CHECKSUM
+
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* FEC_ENET */
+
+#define CONFIG_HOSTNAME		M5329EVB
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"netdev=eth0\0"			\
+	"loadaddr=40010000\0"	\
+	"u-boot=u-boot.bin\0"	\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"	\
+	"prog=prot off 0 2ffff;"	\
+	"era 0 2ffff;"	\
+	"cp.b ${loadaddr} 0 ${filesize};"	\
+	"save\0"	\
+	""
+
+#define CONFIG_PRAM		512	/* 512 KB */
+#define CFG_PROMPT		"-> "
+#define CFG_LONGHELP		/* undef to save memory */
+
+#ifdef CONFIG_CMD_KGDB
+#	define CFG_CBSIZE	1024	/* Console I/O Buffer Size */
+#else
+#	define CFG_CBSIZE	256	/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE			(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
+#define CFG_LOAD_ADDR		0x40010000
+
+#define CFG_HZ			1000
+#define CFG_CLK			80000000
+#define CFG_CPU_CLK		CFG_CLK * 3
+
+#define CFG_MBAR		0xFC000000
+
+#define CFG_LATCH_ADDR		(CFG_CS1_BASE + 0x80000)
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x80000000
+#define CFG_INIT_RAM_END	0x8000	/* End of used area in internal SRAM */
+#define CFG_INIT_RAM_CTRL	0x221
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	((CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) - 0x10)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x40000000
+#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
+#define CFG_SDRAM_CFG1		0x53722730
+#define CFG_SDRAM_CFG2		0x56670000
+#define CFG_SDRAM_CTRL		0xE1092000
+#define CFG_SDRAM_EMOD		0x40010000
+#define CFG_SDRAM_MODE		0x018D0000
+
+#define CFG_MEMTEST_START	CFG_SDRAM_BASE + 0x400
+#define CFG_MEMTEST_END		((CFG_SDRAM_SIZE - 3) << 20)
+
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+
+#define CFG_BOOTPARAMS_LEN	64*1024
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x800000	/* Max size that the board might have */
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#	define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#endif
+
+#ifdef NANDFLASH_SIZE
+#	define CFG_MAX_NAND_DEVICE	1
+#	define CFG_NAND_BASE		(CFG_CS2_BASE << 16)
+#	define CFG_NAND_SIZE		1
+#	define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#	define NAND_MAX_CHIPS		1
+#	define NAND_ALLOW_ERASE_ALL	1
+#	define CONFIG_JFFS2_NAND	1
+#	define CONFIG_JFFS2_DEV		"nand0"
+#	define CONFIG_JFFS2_PART_SIZE	(CFG_CS2_MASK & ~1)
+#	define CONFIG_JFFS2_PART_OFFSET	0x00000000
+#endif
+
+#define CFG_FLASH_BASE		(CFG_CS0_BASE << 16)
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#define CFG_ENV_OFFSET		0x4000
+#define CFG_ENV_SECT_SIZE	0x2000
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_IS_EMBEDDED	1
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	16
+
+/*-----------------------------------------------------------------------
+ * Chipselect bank definitions
+ */
+/*
+ * CS0 - NOR Flash 1, 2, 4, or 8MB
+ * CS1 - CompactFlash and registers
+ * CS2 - NAND Flash 16, 32, or 64MB
+ * CS3 - Available
+ * CS4 - Available
+ * CS5 - Available
+ */
+#define CFG_CS0_BASE		0
+#define CFG_CS0_MASK		0x007f0001
+#define CFG_CS0_CTRL		0x00001fa0
+
+#define CFG_CS1_BASE		0x1000
+#define CFG_CS1_MASK		0x001f0001
+#define CFG_CS1_CTRL		0x002A3780
+
+#ifdef NANDFLASH_SIZE
+#define CFG_CS2_BASE		0x2000
+#define CFG_CS2_MASK		((NANDFLASH_SIZE << 20) | 1)
+#define CFG_CS2_CTRL		0x00001f60
+#endif
+
+#endif				/* _M5329EVB_H */
diff --git a/include/configs/M54455EVB.h b/include/configs/M54455EVB.h
new file mode 100644
index 0000000..6f4859c
--- /dev/null
+++ b/include/configs/M54455EVB.h
@@ -0,0 +1,391 @@
+/*
+ * Configuation settings for the Freescale MCF54455 EVB board.
+ *
+ * Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef _JAMICA54455_H
+#define _JAMICA54455_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_MCF5445x		/* define processor family */
+#define CONFIG_M54455		/* define processor type */
+#define CONFIG_M54455EVB	/* M54455EVB board */
+
+#undef DEBUG
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
+#define CONFIG_BAUDRATE		115200
+#define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
+
+#undef CONFIG_WATCHDOG
+
+#define CONFIG_TIMESTAMP	/* Print image info with timestamp */
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+
+/* Command line configuration */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_LOADS
+
+/* Network configuration */
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI	1
+#	define CONFIG_MII		1
+#	define CONFIG_CF_DOMII
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX	0
+#	define CFG_FEC1_PINMUX	0
+#	define CFG_FEC0_MIIBASE	CFG_FEC0_IOBASE
+#	define CFG_FEC1_MIIBASE	CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 50000
+#	define CONFIG_HAS_ETH1
+
+#	define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
+#	define CONFIG_BOOTARGS		"root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=physmap-flash.0:5M(kernel)ro,-(jffs2)"
+#	define CONFIG_ETHADDR		00:e0:0c:bc:e5:60
+#	define CONFIG_ETH1ADDR		00:e0:0c:bc:e5:61
+#	define CONFIG_ETHPRIME		"FEC0"
+#	define CONFIG_IPADDR		192.162.1.2
+#	define CONFIG_NETMASK		255.255.255.0
+#	define CONFIG_SERVERIP		192.162.1.1
+#	define CONFIG_GATEWAYIP		192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+#define CONFIG_HOSTNAME		M54455EVB
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"inpclk=" MK_STR(CFG_INPUT_CLKSRC) "\0"	\
+	"loadaddr=40010000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off 0 2ffff;"		\
+	"era 0 2ffff;"				\
+	"cp.b ${loadaddr} 0 ${filesize};"	\
+	"save\0"				\
+	""
+
+/* ATA configuration */
+#define CONFIG_ISO_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_IDE_RESET	1
+#define CONFIG_IDE_PREINIT	1
+#define CONFIG_ATAPI
+#undef CONFIG_LBA48
+
+#define CFG_IDE_MAXBUS		1
+#define CFG_IDE_MAXDEVICE	2
+
+#define CFG_ATA_BASE_ADDR	0x90000000
+#define CFG_ATA_IDE0_OFFSET	0
+
+#define CFG_ATA_DATA_OFFSET	0xA0	/* Offset for data I/O                            */
+#define CFG_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers           */
+#define CFG_ATA_STRIDE		4	/* Interval between registers                 */
+#define _IO_BASE		0
+
+/* Realtime clock */
+#define CONFIG_MCFRTC
+#undef RTC_DEBUG
+#define CFG_RTC_OSCILLATOR	(32 * CFG_HZ)
+
+/* Timer */
+#define CONFIG_MCFTMR
+#undef CONFIG_MCFPIT
+
+/* I2c */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C		/* I2C with hardware support */
+#undef	CONFIG_SOFT_I2C		/* I2C bit-banged               */
+#define CFG_I2C_SPEED		80000	/* I2C speed and slave address  */
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_OFFSET		0x58000
+#define CFG_IMMR		CFG_MBAR
+
+/* PCI */
+#define CONFIG_PCI		1
+
+#define CFG_PCI_MEM_BUS		0xA0000000
+#define CFG_PCI_MEM_PHYS	CFG_PCI_MEM_BUS
+#define CFG_PCI_MEM_SIZE	0x10000000
+
+#define CFG_PCI_IO_BUS		0xB1000000
+#define CFG_PCI_IO_PHYS		CFG_PCI_IO_BUS
+#define CFG_PCI_IO_SIZE		0x01000000
+
+#define CFG_PCI_CFG_BUS		0xB0000000
+#define CFG_PCI_CFG_PHYS	CFG_PCI_CFG_BUS
+#define CFG_PCI_CFG_SIZE	0x01000000
+
+/* FPGA - Spartan 2 */
+/* experiment
+#define CONFIG_FPGA		CFG_SPARTAN3
+#define CONFIG_FPGA_COUNT	1
+#define CFG_FPGA_PROG_FEEDBACK
+#define CFG_FPGA_CHECK_CTRLC
+*/
+
+/* Input, PCI, Flexbus, and VCO */
+#define CONFIG_EXTRA_CLOCK
+
+#define CONFIG_PRAM		512	/* 512 KB */
+
+#define CFG_PROMPT		"-> "
+#define CFG_LONGHELP		/* undef to save memory */
+
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE			1024	/* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE			256	/* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
+
+#define CFG_LOAD_ADDR		(CFG_SDRAM_BASE + 0x10000)
+
+#define CFG_HZ			1000
+
+#define CFG_MBAR		0xFC000000
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	0x80000000
+#define CFG_INIT_RAM_END	0x8000	/* End of used area in internal SRAM */
+#define CFG_INIT_RAM_CTRL	0x221
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET	((CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE) - 16)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE		0x40000000
+#define CFG_SDRAM_BASE1		0x48000000
+#define CFG_SDRAM_SIZE		256	/* SDRAM size in MB */
+#define CFG_SDRAM_CFG1		0x65311610
+#define CFG_SDRAM_CFG2		0x59670000
+#define CFG_SDRAM_CTRL		0xEA0B2000
+#define CFG_SDRAM_EMOD		0x40010000
+#define CFG_SDRAM_MODE		0x00010033
+
+#define CFG_MEMTEST_START	CFG_SDRAM_BASE + 0x400
+#define CFG_MEMTEST_END		((CFG_SDRAM_SIZE - 3) << 20)
+
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#define CFG_BOOTPARAMS_LEN	64*1024
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization ??
+ */
+/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+
+/* Configuration for environment
+ * Environment is embedded in u-boot in the second sector of the flash
+ */
+#define CFG_ENV_OFFSET		0x4000
+#define CFG_ENV_SECT_SIZE	0x2000
+#define CFG_ENV_IS_IN_FLASH	1
+#define CONFIG_ENV_OVERWRITE	1
+#undef CFG_ENV_IS_EMBEDDED
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#ifdef CFG_ATMEL_BOOT
+#	define CFG_FLASH_BASE		0
+#	define CFG_FLASH0_BASE		CFG_CS0_BASE
+#	define CFG_FLASH1_BASE		CFG_CS1_BASE
+#else
+#	define CFG_FLASH_BASE		CFG_FLASH0_BASE
+#	define CFG_FLASH0_BASE		CFG_CS1_BASE
+#	define CFG_FLASH1_BASE		CFG_CS0_BASE
+#endif
+
+/* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system
+/* M54455EVB has one non CFI flash, defined CFG_FLASH_CFI will cause the system
+   keep reset. */
+#undef CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x1000000	/* Max size that the board might have */
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
+#	define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#	define CFG_FLASH_CHECKSUM
+#	define CFG_FLASH_BANKS_LIST	{ CFG_CS0_BASE, CFG_CS1_BASE }
+
+#else
+
+#	define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks */
+
+#	define CFG_ATMEL_REGION		4
+#	define CFG_ATMEL_TOTALSECT	11
+#	define CFG_ATMEL_SECT		{1, 2, 1, 7}
+#	define CFG_ATMEL_SECTSZ		{0x4000, 0x2000, 0x8000, 0x10000}
+#	define CFG_INTEL_SECT		137
+
+/* max number of sectors on one chip */
+#	define CFG_MAX_FLASH_SECT	(CFG_ATMEL_TOTALSECT + CFG_INTEL_SECT)
+#	define CFG_FLASH_ERASE_TOUT	2000	/* Atmel needs longer timeout */
+#	define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
+#	define CFG_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
+#	define CFG_FLASH_UNLOCK_TOUT	100	/* Timeout for Flash Clear Lock Bits (in ms) */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#	define CFG_FLASH_CHECKSUM
+
+#endif
+
+/*
+ * This is setting for JFFS2 support in u-boot.
+ * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
+ */
+#ifdef CFG_ATMEL_BOOT
+#	define CONFIG_JFFS2_DEV		"nor0"
+#	define CONFIG_JFFS2_PART_SIZE	0x01000000
+#	define CONFIG_JFFS2_PART_OFFSET	CFG_FLASH1_BASE
+#else
+#	define CONFIG_JFFS2_DEV		"nor0"
+#	define CONFIG_JFFS2_PART_SIZE	(0x01000000 - 0x500000)
+#	define CONFIG_JFFS2_PART_OFFSET	(CFG_FLASH0_BASE + 0x500000)
+#endif
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE		16
+
+/*-----------------------------------------------------------------------
+ * Memory bank definitions
+ */
+/*
+ * CS0 - NOR Flash 1, 2, 4, or 8MB
+ * CS1 - CompactFlash and registers
+ * CS2 - CPLD
+ * CS3 - FPGA
+ * CS4 - Available
+ * CS5 - Available
+ */
+
+#ifdef CFG_ATMEL_BOOT
+ /* Atmel Flash */
+#define CFG_CS0_BASE		0
+#define CFG_CS0_MASK		0x00070001
+#define CFG_CS0_CTRL		0x00001140
+/* Intel Flash */
+#define CFG_CS1_BASE		0x04000000
+#define CFG_CS1_MASK		0x01FF0001
+#define CFG_CS1_CTRL		0x003F3D60
+
+#define CFG_ATMEL_BASE		CFG_CS0_BASE
+#else
+/* Intel Flash */
+#define CFG_CS0_BASE		0
+#define CFG_CS0_MASK		0x01FF0001
+#define CFG_CS0_CTRL		0x003F3D60
+ /* Atmel Flash */
+#define CFG_CS1_BASE		0x04000000
+#define CFG_CS1_MASK		0x00070001
+#define CFG_CS1_CTRL		0x00001140
+
+#define CFG_ATMEL_BASE		CFG_CS1_BASE
+#endif
+
+/* CPLD */
+#define CFG_CS2_BASE		0x08000000
+#define CFG_CS2_MASK		0x00070001
+#define CFG_CS2_CTRL		0x003f1140
+
+/* FPGA */
+#define CFG_CS3_BASE		0x09000000
+#define CFG_CS3_MASK		0x00070001
+#define CFG_CS3_CTRL		0x00000020
+
+#endif				/* _JAMICA54455_H */
diff --git a/include/configs/MPC8313ERDB.h b/include/configs/MPC8313ERDB.h
index 81db96f..6568fe1 100644
--- a/include/configs/MPC8313ERDB.h
+++ b/include/configs/MPC8313ERDB.h
@@ -113,12 +113,12 @@
 				/* 0x03200064 */
 #if defined(CONFIG_DDR_2T_TIMING)
 #define CFG_SDRAM_CFG		( SDRAM_CFG_SREN \
-				| 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
 				| SDRAM_CFG_2T_EN \
 				| SDRAM_CFG_DBW_32 )
 #else
 #define CFG_SDRAM_CFG		( SDRAM_CFG_SREN \
-				| 3 << SDRAM_CFG_SDRAM_TYPE_SHIFT \
+				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
 				| SDRAM_CFG_32_BE )
 				/* 0x43080000 */
 #endif
@@ -228,12 +228,9 @@
 #define CFG_LBLAWAR3_PRELIM	0x8000000E	/* 32KB  */
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8313@0"
 #define OF_SOC			"soc8313@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
@@ -310,6 +307,8 @@
 #define CONFIG_TSEC2_NAME	"TSEC1"
 #define TSEC1_PHY_ADDR			0x1c
 #define TSEC2_PHY_ADDR			4
+#define TSEC1_FLAGS			TSEC_GIGABIT
+#define TSEC2_FLAGS			TSEC_GIGABIT
 #define TSEC1_PHYIDX			0
 #define TSEC2_PHYIDX			0
 
@@ -507,6 +506,7 @@
 
 #define CONFIG_ETHADDR		00:E0:0C:00:95:01
 #define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETH1ADDR		00:E0:0C:00:95:02
 
 #define CONFIG_IPADDR		10.0.0.2
diff --git a/include/configs/MPC832XEMDS.h b/include/configs/MPC832XEMDS.h
index f62ca2c..c9c6d88 100644
--- a/include/configs/MPC832XEMDS.h
+++ b/include/configs/MPC832XEMDS.h
@@ -30,6 +30,8 @@
 #define CONFIG_MPC83XX		1	/* MPC83xx family */
 #define CONFIG_MPC832X		1	/* MPC832x CPU specific */
 #define CONFIG_MPC832XEMDS	1	/* MPC832XEMDS board specific */
+#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */
+#undef CONFIG_PQ_MDS_PIB_ATM	/* QOC3 ATM card */
 
 /*
  * System Clock Setup
@@ -87,6 +89,7 @@
 #define CFG_SICRL		0x00000000
 
 #define CONFIG_BOARD_EARLY_INIT_F	/* call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_R
 
 /*
  * IMMR new address
@@ -315,12 +318,9 @@
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8323@0"
 #define OF_SOC			"soc8323@e0000000"
 #define OF_QE			"qe@e0100000"
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index 1567fcf..92555ba 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -339,12 +339,9 @@
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8349@0"
 #define OF_SOC			"soc8349@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
@@ -440,6 +437,8 @@
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
@@ -699,6 +698,7 @@
 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_ETHADDR		00:04:9f:ef:23:33
 #define CONFIG_HAS_ETH1
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETH1ADDR		00:E0:0C:00:7E:21
 #endif
 
diff --git a/include/configs/MPC8349ITX.h b/include/configs/MPC8349ITX.h
index 44649d0..54cab52 100644
--- a/include/configs/MPC8349ITX.h
+++ b/include/configs/MPC8349ITX.h
@@ -296,12 +296,9 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CFG_NS16550_COM2	(CFG_IMMR + 0x4600)
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8349@0"
 #define OF_SOC			"soc8349@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
@@ -378,10 +375,12 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CONFIG_TSEC1
 
 #ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
 #define CONFIG_TSEC1_NAME  "TSEC0"
 #define CFG_TSEC1_OFFSET	0x24000
 #define TSEC1_PHY_ADDR		0x1c	/* VSC8201 uses address 0x1c */
 #define TSEC1_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
 #endif
 
 #ifdef CONFIG_TSEC2
@@ -391,6 +390,7 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CONFIG_UNKNOWN_TSEC	/* TSEC2 is proprietary */
 #define TSEC2_PHY_ADDR		4
 #define TSEC2_PHYIDX		0
+#define TSEC2_FLAGS		TSEC_GIGABIT
 #endif
 
 #define CONFIG_ETHPRIME		"Freescale TSEC"
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h
index 4b32a14..41f062c 100644
--- a/include/configs/MPC8360EMDS.h
+++ b/include/configs/MPC8360EMDS.h
@@ -32,6 +32,8 @@
 #define CONFIG_MPC83XX		1 /* MPC83XX family */
 #define CONFIG_MPC8360		1 /* MPC8360 CPU specific */
 #define CONFIG_MPC8360EMDS	1 /* MPC8360EMDS board specific */
+#undef CONFIG_PQ_MDS_PIB /* POWERQUICC MDS Platform IO Board */
+#undef CONFIG_PQ_MDS_PIB_ATM /* QOC3 ATM card */
 
 /*
  * System Clock Setup
@@ -88,6 +90,7 @@
 #define CFG_SICRL		0x40000000
 
 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
+#define CONFIG_BOARD_EARLY_INIT_R
 
 /*
  * IMMR new address
@@ -309,13 +312,13 @@
 /*
  * CS4 on Local Bus, to PIB
  */
-#define CFG_BR4_PRELIM	0xf8008801 /* CS4 base address at 0xf8008000 */
+#define CFG_BR4_PRELIM	0xf8010801 /* CS4 base address at 0xf8010000 */
 #define CFG_OR4_PRELIM	0xffffe9f7 /* size 32KB, port size 8bit, GPCM */
 
 /*
  * CS5 on Local Bus, to PIB
  */
-#define CFG_BR5_PRELIM	0xf8010801 /* CS5 base address at 0xf8010000 */
+#define CFG_BR5_PRELIM	0xf8008801 /* CS5 base address at 0xf8008000 */
 #define CFG_OR5_PRELIM	0xffffe9f7 /* size 32KB, port size 8bit, GPCM */
 
 /*
@@ -348,10 +351,6 @@
 #define CONFIG_OF_HAS_BD_T	1
 #define CONFIG_OF_HAS_UBOOT_ENV	1
 
-
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8360@0"
 #define OF_SOC			"soc8360@e0000000"
 #define OF_QE			"qe@e0100000"
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 5a7c879..be603ac 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -301,9 +301,6 @@
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8540@0"
 #define OF_SOC			"soc8540@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -374,6 +371,8 @@
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 
 #if CONFIG_HAS_FEC
@@ -381,6 +380,7 @@
 #define CONFIG_MPC85XX_FEC_NAME		"FEC"
 #define FEC_PHY_ADDR		3
 #define FEC_PHYIDX		0
+#define FEC_FLAGS		0
 #endif
 
 /* Options are: TSEC[0-1], FEC */
@@ -489,6 +489,7 @@
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
diff --git a/include/configs/MPC8540EVAL.h b/include/configs/MPC8540EVAL.h
index 0ce25cf..e376c11 100644
--- a/include/configs/MPC8540EVAL.h
+++ b/include/configs/MPC8540EVAL.h
@@ -213,10 +213,13 @@
 #define CONFIG_NET_MULTI 	1
 #define CONFIG_MII		1	/* MII PHY management	*/
 #define CONFIG_TSEC1    1
+#define CONFIG_HAS_ETH0
 #define CONFIG_TSEC1_NAME      "TSEC0"
 #define CONFIG_TSEC2	1
+#define CONFIG_HAS_ETH1
 #define CONFIG_TSEC2_NAME      "TSEC1"
 #define CONFIG_MPC85XX_FEC      1
+#define CONFIG_HAS_ETH2
 #define CONFIG_MPC85XX_FEC_NAME                "FEC"
 #define TSEC1_PHY_ADDR          7
 #define	TSEC2_PHY_ADDR		4
@@ -224,6 +227,10 @@
 #define TSEC1_PHYIDX            0
 #define TSEC2_PHYIDX            0
 #define FEC_PHYIDX              0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+#define FEC_FLAGS		0
+
 /* Options are: TSEC[0-1], FEC */
 #define CONFIG_ETHPRIME                "TSEC0"
 
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index 232f171..4e061bd 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -312,9 +312,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8541@0"
 #define OF_SOC			"soc8541@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -384,13 +381,12 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
-#define FEC_PHY_ADDR		3
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
-#define FEC_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
@@ -482,6 +478,7 @@ extern unsigned long get_clock_freq(void);
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 32934e1..f580cca 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -181,6 +181,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CFG_BR3_PRELIM		0xf8100801	/* port size 8bit */
 #define CFG_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/
 
+#define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
 #define PIXIS_BASE	0xf8100000	/* PIXIS registers */
 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
 #define PIXIS_VER		0x1	/* Board version at offset 1 */
@@ -252,9 +253,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8544@0"
 #define OF_SOC			"soc8544@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -282,7 +280,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CFG_PCI1_MEM_SIZE	0x20000000	/* 512M */
 #define CFG_PCI1_IO_BASE	0x00000000
 #define CFG_PCI1_IO_PHYS	0xe1000000
-#define CFG_PCI1_IO_SIZE	0x00100000	/* 1M */
+#define CFG_PCI1_IO_SIZE	0x00010000	/* 64k */
 
 /* PCI view of System Memory */
 #define CFG_PCI_MEMORY_BUS	0x00000000
@@ -294,27 +292,27 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CFG_PCIE2_MEM_PHYS	CFG_PCIE2_MEM_BASE
 #define CFG_PCIE2_MEM_SIZE	0x20000000	/* 512M */
 #define CFG_PCIE2_IO_BASE	0x00000000
-#define CFG_PCIE2_IO_PHYS	0xe2000000
-#define CFG_PCIE2_IO_SIZE	0x00100000	/* 1M */
+#define CFG_PCIE2_IO_PHYS	0xe1010000
+#define CFG_PCIE2_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 1, Slot 2,tgtid 2, Base address a000 */
 #define CFG_PCIE1_MEM_BASE	0xa0000000
 #define CFG_PCIE1_MEM_PHYS	CFG_PCIE1_MEM_BASE
-#define CFG_PCIE1_MEM_SIZE	0x08000000	/* 128M */
-#define CFG_PCIE1_MEM_BASE2	0xa8000000
-#define CFG_PCIE1_MEM_PHYS2	CFG_PCIE1_MEM_BASE2
-#define CFG_PCIE1_MEM_SIZE2	0x04000000	/* 64M */
-#define CFG_PCIE1_IO_BASE	0x00000000	/* reuse mem LAW */
-#define CFG_PCIE1_IO_PHYS	0xaf000000
-#define CFG_PCIE1_IO_SIZE	0x00100000	/* 1M */
+#define CFG_PCIE1_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCIE1_IO_BASE	0x00000000
+#define CFG_PCIE1_IO_PHYS	0xe1020000
+#define CFG_PCIE1_IO_SIZE	0x00010000	/* 64k */
 
 /* controller 3, direct to uli, tgtid 3, Base address b000 */
 #define CFG_PCIE3_MEM_BASE	0xb0000000
 #define CFG_PCIE3_MEM_PHYS	CFG_PCIE3_MEM_BASE
-#define CFG_PCIE3_MEM_SIZE	0x10000000	/* 256M */
+#define CFG_PCIE3_MEM_SIZE	0x00100000	/* 1M */
 #define CFG_PCIE3_IO_BASE	0x00000000
-#define CFG_PCIE3_IO_PHYS	0xe3000000
+#define CFG_PCIE3_IO_PHYS	0xb0100000	/* reuse mem LAW */
 #define CFG_PCIE3_IO_SIZE	0x00100000	/* 1M */
+#define CFG_PCIE3_MEM_BASE2	0xb0200000
+#define CFG_PCIE3_MEM_PHYS2	CFG_PCIE3_MEM_BASE2
+#define CFG_PCIE3_MEM_SIZE2	0x00200000	/* 1M */
 
 #if defined(CONFIG_PCI)
 
@@ -364,15 +362,13 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_TSEC1_NAME	"eTSEC1"
 #define CONFIG_TSEC3	1
 #define CONFIG_TSEC3_NAME	"eTSEC3"
-#undef CONFIG_MPC85XX_FEC
-
-#define CONFIG_TSEC_TBI		1	/* enable internal TBI phy */
-#define CONFIG_SGMII_RISER
-#define TSEC1_SGMII_PHY_ADDR_OFFSET	0x1c	/* sgmii phy base */
 
 #define TSEC1_PHY_ADDR		0
 #define TSEC3_PHY_ADDR		1
 
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+
 #define TSEC1_PHYIDX		0
 #define TSEC3_PHYIDX		0
 
@@ -474,6 +470,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR	00:E0:0C:02:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR	00:E0:0C:02:01:FD
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index cda9fd5..6083715 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -336,9 +336,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8548@0"
 #define OF_SOC			"soc8548@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -447,6 +444,10 @@ extern unsigned long get_clock_freq(void);
 #define TSEC2_PHYIDX		0
 #define TSEC3_PHYIDX		0
 #define TSEC4_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
 
 /* Options are: eTSEC[0-3] */
 #define CONFIG_ETHPRIME		"eTSEC0"
@@ -538,6 +539,7 @@ extern unsigned long get_clock_freq(void);
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR	 00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR	 00:E0:0C:00:01:FD
@@ -631,7 +633,6 @@ extern unsigned long get_clock_freq(void);
 #define ENET_ENV ""
 #endif
 
-#if 0
 #define	CONFIG_EXTRA_ENV_SETTINGS				\
  "netdev=eth0\0"						\
  "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"				\
@@ -644,8 +645,8 @@ extern unsigned long get_clock_freq(void);
  "consoledev=ttyS1\0"				\
  "ramdiskaddr=2000000\0"			\
  "ramdiskfile=ramdisk.uboot\0"			\
- "dtbaddr=c00000\0"				\
- "dtbfile=mpc8548cds.dtb\0"			\
+ "fdtaddr=c00000\0"				\
+ "fdtfile=mpc8548cds.dtb\0"			\
  "eoi=mw e00400b0 0\0"				\
  "iack=md e00400a0 1\0"				\
  "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4; md ${a}bf0 4;" \
@@ -667,8 +668,6 @@ extern unsigned long get_clock_freq(void);
  PCI_ENV1 \
  PCI_ENV2 \
  ENET_ENV
-#endif
-
 
 #define CONFIG_NFSBOOTCOMMAND						\
    "setenv bootargs root=/dev/nfs rw "					\
@@ -676,8 +675,8 @@ extern unsigned long get_clock_freq(void);
       "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
       "console=$consoledev,$baudrate $othbootargs;"			\
    "tftp $loadaddr $bootfile;"						\
-   "tftp $dtbaddr $dtbfile;"						\
-   "bootm $loadaddr - $dtbaddr"
+   "tftp $fdtaddr $fdtfile;"						\
+   "bootm $loadaddr - $fdtaddr"
 
 
 #define CONFIG_RAMBOOTCOMMAND \
@@ -685,8 +684,8 @@ extern unsigned long get_clock_freq(void);
       "console=$consoledev,$baudrate $othbootargs;"			\
    "tftp $ramdiskaddr $ramdiskfile;"					\
    "tftp $loadaddr $bootfile;"						\
-   "tftp $dtbaddr $dtbfile;"						\
-   "bootm $loadaddr $ramdiskaddr $dtbaddr"
+   "tftp $fdtaddr $fdtfile;"						\
+   "bootm $loadaddr $ramdiskaddr $fdtaddr"
 
 #define CONFIG_BOOTCOMMAND	CONFIG_NFSBOOTCOMMAND
 
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index e8fe99a..1d1b7c9 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -312,9 +312,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8555@0"
 #define OF_SOC			"soc8555@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -384,13 +381,12 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
-#define FEC_PHY_ADDR		3
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
-#define FEC_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
@@ -482,6 +478,7 @@ extern unsigned long get_clock_freq(void);
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index c10e551..a8f362f 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -292,9 +292,6 @@
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8560@0"
 #define OF_SOC			"soc8560@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
@@ -360,11 +357,12 @@
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
@@ -521,6 +519,7 @@
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:E0:0C:00:00:FD
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:E0:0C:00:01:FD
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index dc9cb1f..ba744e9 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -35,7 +35,7 @@
 
 #define CONFIG_PCI
 #define CONFIG_TSEC_ENET 		/* tsec ethernet support */
-#undef CONFIG_QE			/* Enable QE */
+#define CONFIG_QE			/* Enable QE */
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_DLL			/* possible DLL fix needed */
@@ -63,9 +63,9 @@ extern unsigned long get_clock_freq(void);
 /*
  * These can be toggled for performance analysis, otherwise use default.
  */
-/*#define CONFIG_L2_CACHE*/		    	    /* toggle L2 cache 	*/
-#define CONFIG_BTB						/* toggle branch predition */
-#define CONFIG_ADDR_STREAMING		    /* toggle addr streaming   */
+#define CONFIG_L2_CACHE				/* toggle L2 cache 	*/
+#define CONFIG_BTB				/* toggle branch predition */
+#define CONFIG_ADDR_STREAMING			/* toggle addr streaming   */
 
 /*
  * Only possible on E500 Version 2 or newer cores.
@@ -293,9 +293,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8568@0"
 #define OF_SOC			"soc8568@e0000000"
 #define OF_QE			"qe@e0080000"
@@ -348,7 +345,7 @@ extern unsigned long get_clock_freq(void);
  */
 #define CONFIG_UEC_ETH
 #ifndef CONFIG_TSEC_ENET
-#define CONFIG_ETHPRIME         "Freescale GETH"
+#define CONFIG_ETHPRIME         "FSL UEC0"
 #endif
 #define CONFIG_PHY_MODE_NEED_CHANGE
 #define CONFIG_eTSEC_MDIO_BUS
@@ -399,9 +396,6 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_TSEC1_NAME	"eTSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"eTSEC1"
-#undef  CONFIG_TSEC3
-#undef  CONFIG_TSEC4
-#undef  CONFIG_MPC85XX_FEC
 
 #define TSEC1_PHY_ADDR		2
 #define TSEC2_PHY_ADDR		3
@@ -409,7 +403,10 @@ extern unsigned long get_clock_freq(void);
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 
-/* Options are: eTSEC[0-3] */
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+
+/* Options are: eTSEC[0-1] */
 #define CONFIG_ETHPRIME		"eTSEC0"
 
 #endif	/* CONFIG_TSEC_ENET */
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 64dcbd0..7d8a380 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -185,6 +185,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CFG_OR3_PRELIM		0xfff06ff7	/* 1MB PIXIS area*/
 
 
+#define CONFIG_FSL_PIXIS	1	/* use common PIXIS code */
 #define PIXIS_BASE	0xf8100000      /* PIXIS registers */
 #define PIXIS_ID		0x0	/* Board ID at offset 0 */
 #define PIXIS_VER		0x1	/* Board version at offset 1 */
@@ -268,9 +269,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU		"PowerPC,8641@0"
 #define OF_SOC		"soc8641@f8000000"
 #define OF_TBCLK	(bd->bi_busfreq / 4)
@@ -417,6 +415,10 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define TSEC2_PHYIDX		0
 #define TSEC3_PHYIDX		0
 #define TSEC4_PHYIDX		0
+#define TSEC1_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC3_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC4_FLAGS		(TSEC_GIGABIT | TSEC_REDUCED)
 
 #define CONFIG_ETHPRIME		"eTSEC1"
 
@@ -604,6 +606,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_ETH3ADDR  00:E0:0C:00:03:FD
 #endif
 
+#define CONFIG_HAS_ETH0		1
 #define CONFIG_HAS_ETH1		1
 #define CONFIG_HAS_ETH2		1
 #define CONFIG_HAS_ETH3		1
diff --git a/include/configs/PLU405.h b/include/configs/PLU405.h
index 5470373..4acbcd5 100644
--- a/include/configs/PLU405.h
+++ b/include/configs/PLU405.h
@@ -96,7 +96,6 @@
 #define CONFIG_SUPPORT_VFAT
 
 #define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
-#define CONFIG_AUTO_UPDATE_SHOW 1       /* use board show routine       */
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -168,36 +167,15 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
 
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
@@ -276,11 +254,6 @@
 
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#if 0 /* test-only */
-#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
-#endif
-
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
@@ -306,9 +279,6 @@
 #define CFG_ENV_SIZE		0x700	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC16 is 2048 bytes */
 
-#define CFG_NVRAM_BASE_ADDR	0xF0000500		/* NVRAM base address	*/
-#define CFG_NVRAM_SIZE		242			/* NVRAM size		*/
-
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC16) for environment
  */
@@ -317,7 +287,7 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT24WC08		*/
-#if 1 /* test-only */
+
 /* CAT24WC08/16... */
 #define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
 /* mask of address bits that overflow into the "EEPROM chip address"	*/
@@ -325,15 +295,6 @@
 #define CFG_EEPROM_PAGE_WRITE_BITS 4	/* The Catalyst CAT24WC08 has	*/
 					/* 16 byte page write mode using*/
 					/* last 4 bits of the address	*/
-#else
-/* CAT24WC32/64... */
-#define CFG_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"	*/
-#define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x01
-#define CFG_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
-					/* 32 byte page write mode using*/
-					/* last 5 bits of the address	*/
-#endif
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
diff --git a/include/configs/PM854.h b/include/configs/PM854.h
index dbf9422..a6a1e73 100644
--- a/include/configs/PM854.h
+++ b/include/configs/PM854.h
@@ -270,15 +270,19 @@
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 #define CONFIG_MPC85XX_FEC	1
 #define CONFIG_MPC85XX_FEC_NAME		"FEC"
 #define FEC_PHY_ADDR		3
 #define FEC_PHYIDX		0
+#define FEC_FLAGS		0
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
 
+#define CONFIG_HAS_ETH0
 #define	CONFIG_HAS_ETH1		1
 #define	CONFIG_HAS_ETH2		1
 
diff --git a/include/configs/PM856.h b/include/configs/PM856.h
index 6bdfa5d..9a17e3d 100644
--- a/include/configs/PM856.h
+++ b/include/configs/PM856.h
@@ -262,11 +262,12 @@
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#undef CONFIG_MPC85XX_FEC
 #define TSEC1_PHY_ADDR		0
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 #endif  /* CONFIG_TSEC_ENET */
 
@@ -391,6 +392,7 @@
 
 /* The mac addresses for all ethernet interface */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR   00:40:42:01:00:00
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:40:42:01:00:01
diff --git a/include/configs/TASREG.h b/include/configs/TASREG.h
index 2b2ae01..dccdf0c 100644
--- a/include/configs/TASREG.h
+++ b/include/configs/TASREG.h
@@ -43,6 +43,10 @@
 
 #define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
 
+#define CONFIG_MCFTMR
+
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
diff --git a/include/configs/TQM5200.h b/include/configs/TQM5200.h
index 3d98500..e0c9d81 100644
--- a/include/configs/TQM5200.h
+++ b/include/configs/TQM5200.h
@@ -701,11 +701,9 @@
  * Open firmware flat tree support
  *-----------------------------------------------------------------------
  */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
diff --git a/include/configs/TQM834x.h b/include/configs/TQM834x.h
index 661712b..0147252 100644
--- a/include/configs/TQM834x.h
+++ b/include/configs/TQM834x.h
@@ -253,6 +253,8 @@ extern int tqm834x_num_flash_banks;
 #define TSEC2_PHY_ADDR			1
 #define TSEC1_PHYIDX			0
 #define TSEC2_PHYIDX			0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME			"TSEC0"
@@ -499,6 +501,7 @@ extern int tqm834x_num_flash_banks;
  */
 
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR		D2:DA:5E:44:BC:29
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR		1E:F3:40:21:92:53
diff --git a/include/configs/TQM85xx.h b/include/configs/TQM85xx.h
index d5ce3ba..2f23c50 100644
--- a/include/configs/TQM85xx.h
+++ b/include/configs/TQM85xx.h
@@ -94,7 +94,6 @@
  */
 #define CFG_DDR_SDRAM_BASE	0x00000000	/* DDR is system memory	*/
 #define CFG_SDRAM_BASE		CFG_DDR_SDRAM_BASE
-#define CONFIG_ADD_RAM_INFO	1		/* print additional info*/
 
 #if defined(CONFIG_TQM8540) || defined(CONFIG_TQM8560)
 /* TQM8540 & 8560 need DLL-override */
@@ -266,8 +265,12 @@
 #define TSEC2_PHY_ADDR		1
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 #define FEC_PHY_ADDR		3
 #define FEC_PHYIDX		0
+#define FEC_FLAGS		0
+#define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #define CONFIG_HAS_ETH2
 
diff --git a/include/configs/VOH405.h b/include/configs/VOH405.h
index 34f0ebd..3880ec7 100644
--- a/include/configs/VOH405.h
+++ b/include/configs/VOH405.h
@@ -153,36 +153,15 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
diff --git a/include/configs/WUH405.h b/include/configs/WUH405.h
index c1b3da8..656784a 100644
--- a/include/configs/WUH405.h
+++ b/include/configs/WUH405.h
@@ -145,38 +145,16 @@
  * NAND-FLASH stuff
  *-----------------------------------------------------------------------
  */
-#define CFG_NAND_LEGACY
-
-#define CFG_MAX_NAND_DEVICE	1	/* Max number of NAND devices		*/
-#define SECTORSIZE 512
-
-#define ADDR_COLUMN 1
-#define ADDR_PAGE 2
-#define ADDR_COLUMN_PAGE 3
-
-#define NAND_ChipID_UNKNOWN	0x00
-#define NAND_MAX_FLOORS 1
-#define NAND_MAX_CHIPS 1
-
-#define CFG_NAND_CE  (0x80000000 >> 1)	/* our CE is GPIO1 */
-#define CFG_NAND_CLE (0x80000000 >> 2)	/* our CLE is GPIO2 */
-#define CFG_NAND_ALE (0x80000000 >> 3)	/* our ALE is GPIO3 */
-#define CFG_NAND_RDY (0x80000000 >> 4)	/* our RDY is GPIO4 */
-
-#define NAND_DISABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CE);} while(0)
-#define NAND_ENABLE_CE(nand) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CE);} while(0)
-#define NAND_CTL_CLRALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_ALE);} while(0)
-#define NAND_CTL_SETALE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_ALE);} while(0)
-#define NAND_CTL_CLRCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) & ~CFG_NAND_CLE);} while(0)
-#define NAND_CTL_SETCLE(nandptr) do { out32(GPIO0_OR, in32(GPIO0_OR) | CFG_NAND_CLE);} while(0)
-#define NAND_WAIT_READY(nand) while (!(in32(GPIO0_IR) & CFG_NAND_RDY))
-
-#define WRITE_NAND_COMMAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND_ADDRESS(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)(d); } while(0)
-#define WRITE_NAND(d, adr) do{ *(volatile __u8 *)((unsigned long)adr) = (__u8)d; } while(0)
-#define READ_NAND(adr) ((volatile unsigned char)(*(volatile __u8 *)(unsigned long)adr))
-
-#define CONFIG_MTD_NAND_VERIFY_WRITE 1  /* verify all writes!!!         */
+#define CFG_NAND_BASE_LIST	{ CFG_NAND_BASE }
+#define NAND_MAX_CHIPS          1
+#define CFG_MAX_NAND_DEVICE	1         /* Max number of NAND devices */
+#define NAND_BIG_DELAY_US	25
+
+#define CFG_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
+#define CFG_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
+#define CFG_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
+#define CFG_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
+
 #define CFG_NAND_SKIP_BAD_DOT_I      1  /* ".i" read skips bad blocks   */
 
 /*-----------------------------------------------------------------------
diff --git a/include/configs/cmi_mpc5xx.h b/include/configs/cmi_mpc5xx.h
index cd92af2..85c2b96 100644
--- a/include/configs/cmi_mpc5xx.h
+++ b/include/configs/cmi_mpc5xx.h
@@ -59,6 +59,8 @@
  */
 #include <config_cmd_default.h>
 
+#undef	CONFIG_CMD_NET		/* disabeled - causes compile errors */
+
 #define CONFIG_CMD_MEMORY
 #define CONFIG_CMD_LOADB
 #define CONFIG_CMD_REGINFO
diff --git a/include/configs/cobra5272.h b/include/configs/cobra5272.h
index 510524a..104d94e 100644
--- a/include/configs/cobra5272.h
+++ b/include/configs/cobra5272.h
@@ -65,8 +65,10 @@
  * Enable use of Ethernet
  * ---
  */
+#define CONFIG_MCFFEC
 
-#define FEC_ENET
+/* Enable Dma Timer */
+#define CONFIG_MCFTMR
 
 /* ---
  * Define baudrate for UART1 (console output, tftp, ...)
@@ -76,6 +78,8 @@
  * ---
  */
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
@@ -151,6 +155,26 @@
 #undef CONFIG_CMD_LOADB
 #undef CONFIG_CMD_MII
 
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
 /*
  *-----------------------------------------------------------------------------
diff --git a/include/configs/hcu5.h b/include/configs/hcu5.h
index d0bf251..9085881 100644
--- a/include/configs/hcu5.h
+++ b/include/configs/hcu5.h
@@ -43,7 +43,6 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
 #define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
@@ -74,7 +73,6 @@
  * Initial RAM & stack pointer
  *----------------------------------------------------------------------*/
 /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache	*/
-#define CFG_INIT_RAM_OCM	1		/* OCM as init ram	*/
 #define CFG_INIT_RAM_ADDR	CFG_OCM_BASE	/* OCM			*/
 
 #define CFG_INIT_RAM_END	(4 << 10)
diff --git a/include/configs/idmr.h b/include/configs/idmr.h
index 1ab7b27..404e88a 100644
--- a/include/configs/idmr.h
+++ b/include/configs/idmr.h
@@ -44,6 +44,8 @@
  */
 #define CONFIG_BOOTCOMMAND	"run net_nfs"
 #define CONFIG_BOOTDELAY	5
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
 #define CONFIG_ETHADDR		00:06:3b:01:41:55
@@ -58,6 +60,8 @@
 #define CONFIG_PREBOOT		"echo;echo Type \"run flash_nfs\" to mount root " \
 				"filesystem over NFS; echo"
 
+#define CONFIG_MCFTMR
+
 #define CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
@@ -147,11 +151,27 @@
 /*
  * Ethernet
  */
-#define FEC_ENET
-#define CONFIG_NET_RETRY_COUNT	5
-#define CFG_ENET_BD_BASE	0x480000
-#define CFG_DISCOVER_PHY	1
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
 #define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
 /*
  * Definitions for initial stack pointer and data area (in DPRAM)
@@ -186,7 +206,7 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /* FLASH organization */
 #define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
@@ -216,7 +236,7 @@
 						"-(user)";
 
 #if defined(CONFIG_CMD_MII)
-#error MII commands don't work on iDMR board and sholud not be enabled.
+#error "MII commands don't work on iDMR board and should not be enabled."
 #endif
 
 #endif /* _IDMR_H */
diff --git a/include/configs/jupiter.h b/include/configs/jupiter.h
index b68c5aa..b7100e9 100644
--- a/include/configs/jupiter.h
+++ b/include/configs/jupiter.h
@@ -145,12 +145,9 @@
 
 #if 0
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 110ad44..7908e5a 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -42,7 +42,6 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_pre_init		*/
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 #undef  CONFIG_SHOW_BOOT_PROGRESS
 
 /*-----------------------------------------------------------------------
@@ -67,11 +66,11 @@
 #define CFG_PCIE_BASE		0xe0000000	/* PCIe UTL regs */
 
 #define CFG_PCIE0_CFGBASE	0xc0000000
-#define CFG_PCIE0_XCFGBASE	0xc0000400
-#define CFG_PCIE1_CFGBASE	0xc0001000
-#define CFG_PCIE1_XCFGBASE	0xc0001400
-#define CFG_PCIE2_CFGBASE	0xc0002000
-#define CFG_PCIE2_XCFGBASE	0xc0002400
+#define CFG_PCIE1_CFGBASE	0xc1000000
+#define CFG_PCIE2_CFGBASE	0xc2000000
+#define CFG_PCIE0_XCFGBASE	0xc3000000
+#define CFG_PCIE1_XCFGBASE	0xc3001000
+#define CFG_PCIE2_XCFGBASE	0xc3002000
 
 /* System RAM mapped to PCI space */
 #define CONFIG_PCI_SYS_MEM_BUS	CFG_SDRAM_BASE
@@ -202,6 +201,7 @@
 		"setenv filesize;saveenv\0"				\
 	"upd=run load;run update\0"					\
 	"kozio=bootm ffc60000\0"					\
+	"pciconfighost=1\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -323,7 +323,7 @@
 #define CONFIG_PCI			/* include pci support		*/
 #define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
-#undef CONFIG_PCI_CONFIG_HOST_BRIDGE
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE
 
 /* Board-specific PCI */
 #define CFG_PCI_TARGET_INIT		/* let board init pci target    */
diff --git a/include/configs/luan.h b/include/configs/luan.h
index 26dbec9..a09dd74 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -39,7 +39,6 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
diff --git a/include/configs/lwmon5.h b/include/configs/lwmon5.h
index 604b7d1..be48324 100644
--- a/include/configs/lwmon5.h
+++ b/include/configs/lwmon5.h
@@ -34,8 +34,8 @@
 #define CONFIG_SYS_CLK_FREQ	33300000	/* external freq to pll	*/
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
+#define CONFIG_BOARD_POSTCLK_INIT 1	/* Call board_postclk_init	*/
 #define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
@@ -72,7 +72,6 @@
  * Initial RAM & stack pointer
  *----------------------------------------------------------------------*/
 /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache	*/
-#define CFG_INIT_RAM_OCM	1		/* OCM as init ram	*/
 #define CFG_INIT_RAM_ADDR	CFG_OCM_BASE	/* OCM			*/
 #define CFG_OCM_DATA_ADDR	CFG_OCM_BASE
 
@@ -143,15 +142,16 @@
 #endif
 
 /* POST support */
-#define CONFIG_POST		(CFG_POST_MEMORY   | \
-				 CFG_POST_ECC_ON   | \
+#define CONFIG_POST		(CFG_POST_CACHE    | \
 				 CFG_POST_CPU	   | \
-				 CFG_POST_UART	   | \
-				 CFG_POST_I2C	   | \
-				 CFG_POST_CACHE	   | \
-				 CFG_POST_FPU	   | \
+				 CFG_POST_ECC_ON   | \
 				 CFG_POST_ETHER	   | \
-				 CFG_POST_SPR)
+				 CFG_POST_FPU	   | \
+				 CFG_POST_I2C	   | \
+				 CFG_POST_MEMORY   | \
+				 CFG_POST_RTC      | \
+				 CFG_POST_SPR      | \
+				 CFG_POST_UART)
 
 #define CFG_POST_CACHE_ADDR	0x10000000	/* free virtual address		*/
 #define CONFIG_LOGBUFFER
@@ -162,22 +162,29 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000		/* I2C speed and slave address	*/
+#define CFG_I2C_SPEED		100000		/* I2C speed and slave address	*/
 #define CFG_I2C_SLAVE		0x7F
 
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_I2C_EEPROM_ADDR	0x53	/* EEPROM AT24C128		*/
+#define CFG_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address		*/
+#define CFG_EEPROM_PAGE_WRITE_BITS 6	/* The Atmel AT24C128 has	*/
+					/* 64 byte page write mode using*/
+					/* last 6 bits of the address	*/
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 
 #define CONFIG_RTC_PCF8563	1		/* enable Philips PCF8563 RTC	*/
 #define CFG_I2C_RTC_ADDR	0x51		/* Philips PCF8563 RTC address	*/
+#define CFG_I2C_KEYBD_ADDR	0x56		/* PIC LWE keyboard		*/
+
+#define	CONFIG_POST_KEY_MAGIC	"3C+3E"	/* press F3 + F5 keys to force POST */
+#if 0
+#define	CONFIG_AUTOBOOT_KEYED		/* Enable "password" protection	*/
+#define CONFIG_AUTOBOOT_PROMPT	"\nEnter password - autoboot in %d sec...\n"
+#define CONFIG_AUTOBOOT_DELAY_STR	"  "	/* "password"	*/
+#endif
 
-#define CONFIG_PREBOOT	"echo;"						\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
-	"echo"
+#define	CONFIG_PREBOOT		"setenv bootdelay 15"
 
 #undef	CONFIG_BOOTARGS
 
@@ -226,6 +233,7 @@
 #define CONFIG_PHY_ADDR		3	/* PHY address, See schematics	*/
 
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup         */
+#define CONFIG_PHY_RESET_DELAY	300
 
 #define CONFIG_HAS_ETH0
 #define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
@@ -391,9 +399,11 @@
 #define CFG_GPIO_PHY1_RST	12
 #define CFG_GPIO_FLASH_WP	14
 #define CFG_GPIO_PHY0_RST	22
-#define CFG_GPIO_WATCHDOG	58
+#define CFG_GPIO_EEPROM_EXT_WP	55
+#define CFG_GPIO_EEPROM_INT_WP	57
 #define CFG_GPIO_LIME_S		59
 #define CFG_GPIO_LIME_RST	60
+#define CFG_GPIO_WATCHDOG	63
 
 /*-----------------------------------------------------------------------
  * PPC440 GPIO Configuration
diff --git a/include/configs/motionpro.h b/include/configs/motionpro.h
index e0a827f..9a21632 100644
--- a/include/configs/motionpro.h
+++ b/include/configs/motionpro.h
@@ -417,11 +417,9 @@ extern void __led_set(led_id_t id, int state);
 #define CFG_RESET_ADDRESS	0xfff00100
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h
index f4f33f3..bd3107a 100644
--- a/include/configs/mpc7448hpc2.h
+++ b/include/configs/mpc7448hpc2.h
@@ -80,9 +80,6 @@
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,7448@0"
 #define OF_TSI			"tsi108@c0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
diff --git a/include/configs/p3mx.h b/include/configs/p3mx.h
index 8ae38cb..bec442d 100644
--- a/include/configs/p3mx.h
+++ b/include/configs/p3mx.h
@@ -60,7 +60,6 @@
 #define CONFIG_BOARD_EARLY_INIT_F 1     /* Call board_early_init_f	*/
 #define CONFIG_BOARD_EARLY_INIT_R 1     /* Call board_early_init_f	*/
 #define CONFIG_MISC_INIT_R      1	/* Call misc_init_r()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h
index 8e51d2d..7653ba1 100644
--- a/include/configs/pcs440ep.h
+++ b/include/configs/pcs440ep.h
@@ -266,7 +266,10 @@
 #define CONFIG_CMD_DIAG
 #define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_ELF
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
 #define CONFIG_CMD_I2C
+#define CONFIG_CMD_IDE
 #define CONFIG_CMD_IRQ
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_NET
@@ -274,12 +277,10 @@
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_REISER
 #define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
 #define CONFIG_CMD_USB
 
-
 #define CONFIG_SUPPORT_VFAT
 
 /*
@@ -488,10 +489,4 @@
 /* Offset for alternate registers	*/
 #define CFG_ATA_ALT_OFFSET	(0x0000)
 
-/* These addresses need to be shifted one place to the left
- * ( bus per_addr 20 -30 is connectsd on CF bus A10-A0)
- * These values are shifted
- */
-#define CFG_ATA_PORT_ADDR(port) ((port) << 1)
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/r5200.h b/include/configs/r5200.h
index 0e743bb..fc7658b 100644
--- a/include/configs/r5200.h
+++ b/include/configs/r5200.h
@@ -39,13 +39,10 @@
 #define CONFIG_M5271			/* define processor type */
 #define CONFIG_R5200			/* define board type */
 
-#define FEC_ENET
-#define CONFIG_NET_RETRY_COUNT 5
-
-#define CONFIG_IPADDR 192.168.0.172
-#define CONFIG_SERVERIP 192.168.0.148
-#define CONFIG_ETHADDR 00:06:3b:00:44:55
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
@@ -87,6 +84,27 @@
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
 /* Note: We only copy one sectors worth of application code from location
  * 10200000 for speed purposes.  Increase the size if necessary */
diff --git a/include/configs/sbc8349.h b/include/configs/sbc8349.h
index 1831bef..e7d8a5a 100644
--- a/include/configs/sbc8349.h
+++ b/include/configs/sbc8349.h
@@ -313,9 +313,6 @@
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,8349@0"
 #define OF_SOC			"soc8349@e0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 4)
@@ -410,6 +407,8 @@
 #define TSEC2_PHY_ADDR		0x1a
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 
 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"
@@ -660,6 +659,7 @@
 #define CONFIG_ENV_OVERWRITE
 
 #if defined(CONFIG_TSEC_ENET)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR		00:a0:1e:a0:13:8d
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR		00:a0:1e:a0:13:8e
diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
index 68d31ca..54eac38 100644
--- a/include/configs/sbc8641d.h
+++ b/include/configs/sbc8641d.h
@@ -270,9 +270,6 @@
 #define CONFIG_OF_FLAT_TREE	1
 #define CONFIG_OF_BOARD_SETUP	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU		"PowerPC,8641@0"
 #define OF_SOC		"soc@f8000000"
 #define OF_TBCLK	(bd->bi_busfreq / 4)
@@ -380,6 +377,10 @@
 #define TSEC2_PHYIDX		0
 #define TSEC3_PHYIDX		0
 #define TSEC4_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
+#define TSEC3_FLAGS		TSEC_GIGABIT
+#define TSEC4_FLAGS		TSEC_GIGABIT
 
 #define CFG_TBIPA_VALUE	0x1e	/* Set TBI address not to conflict with TSEC1_PHY_ADDR */
 
@@ -492,7 +493,7 @@
 #define CFG_LOAD_ADDR	0x2000000	/* default load address */
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
     #define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
     #define CFG_CBSIZE	256		/* Console I/O Buffer Size */
@@ -513,7 +514,7 @@
 /* Cache Configuration */
 #define CFG_DCACHE_SIZE		32768
 #define CFG_CACHELINE_SIZE	32
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/*log base 2 of the above value*/
 #endif
 
@@ -525,7 +526,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
 #define BOOTFLAG_WARM	0x02		/* Software reboot */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
@@ -542,6 +543,7 @@
 #define CONFIG_ETH3ADDR  02:E0:0C:00:03:FD
 #endif
 
+#define CONFIG_HAS_ETH0		1
 #define CONFIG_HAS_ETH1		1
 #define CONFIG_HAS_ETH2		1
 #define CONFIG_HAS_ETH3		1
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 3f75a44..c2e1386 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -343,6 +343,11 @@
 #define CONFIG_CMD_USB
 #endif
 
+#ifndef CONFIG_RAINIER
+#define CFG_POST_FPU_ON		CFG_POST_FPU
+#else
+#define CFG_POST_FPU_ON		0
+#endif
 
 /* POST support */
 #define CONFIG_POST		(CFG_POST_MEMORY   | \
@@ -350,7 +355,7 @@
 				 CFG_POST_UART	   | \
 				 CFG_POST_I2C	   | \
 				 CFG_POST_CACHE	   | \
-				 CFG_POST_FPU	   | \
+				 CFG_POST_FPU_ON   | \
 				 CFG_POST_ETHER	   | \
 				 CFG_POST_SPR)
 
@@ -395,7 +400,8 @@
  *----------------------------------------------------------------------*/
 /* General PCI */
 #define CONFIG_PCI			/* include pci support	        */
-#undef CONFIG_PCI_PNP			/* do (not) pci plug-and-play   */
+#define CONFIG_PCI_PNP			/* do pci plug-and-play   */
+#define CFG_PCI_CACHE_LINE_SIZE	0 /* to avoid problems with PNP */
 #define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup  */
 #define CFG_PCI_TARGBASE        0x80000000 /* PCIaddr mapped to CFG_PCI_MEMBASE*/
 
diff --git a/include/configs/spc1920.h b/include/configs/spc1920.h
index b4ab9ad..2efc8f1 100644
--- a/include/configs/spc1920.h
+++ b/include/configs/spc1920.h
@@ -31,14 +31,9 @@
 #undef	CONFIG_8xx_CONS_NONE
 
 #define CONFIG_MII
-/* #define MII_DEBUG */
-/* #define CONFIG_FEC_ENET */
 #undef CONFIG_ETHER_ON_FEC1
 #define CONFIG_ETHER_ON_FEC2
 #define FEC_ENET
-/* #define CONFIG_FEC2_PHY_NORXERR */
-/* #define CFG_DISCOVER_PHY */
-/* #define CONFIG_PHY_ADDR		0x1 */
 #define CONFIG_FEC2_PHY		1
 
 #define CONFIG_BAUDRATE		19200
@@ -100,14 +95,12 @@
 #define CONFIG_CMD_ECHO
 #define CONFIG_CMD_IMMAP
 #define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_NET
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 
-#undef CONFIG_CMD_NET
-
-
 /*
  * Miscellaneous configurable options
  */
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index 1f41cf7..c5ae0cd 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -234,12 +234,13 @@
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#undef CONFIG_MPS85XX_FEC
 
 #define TSEC1_PHY_ADDR		2
 #define TSEC2_PHY_ADDR		4
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 #define CONFIG_ETHPRIME		"TSEC0"
 
 #elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
@@ -378,6 +379,7 @@
 
 /*Note: change below for your network setting!!! */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR	 00:e0:0c:07:9b:8a
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:e0:0c:07:9b:8b
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
index 55e2c8d..f32ff67 100644
--- a/include/configs/stxssa.h
+++ b/include/configs/stxssa.h
@@ -260,12 +260,13 @@
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
-#define CONFIG_MPS85XX_FEC
 
 #define TSEC1_PHY_ADDR		2
 #define TSEC2_PHY_ADDR		4
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
+#define TSEC1_FLAGS		TSEC_GIGABIT
+#define TSEC2_FLAGS		TSEC_GIGABIT
 #define CONFIG_ETHPRIME		"TSEC0"
 
 #elif defined(CONFIG_ETHER_ON_FCC)	/* CPM FCC Ethernet */
@@ -406,6 +407,7 @@
 
 /*Note: change below for your network setting!!! */
 #if defined(CONFIG_TSEC_ENET) || defined(CONFIG_ETHER_ON_FCC)
+#define CONFIG_HAS_ETH0
 #define CONFIG_ETHADDR	 00:e0:0c:07:9b:8a
 #define CONFIG_HAS_ETH1
 #define CONFIG_ETH1ADDR  00:e0:0c:07:9b:8b
diff --git a/include/configs/stxxtc.h b/include/configs/stxxtc.h
index 0dbf4b7..b035857 100644
--- a/include/configs/stxxtc.h
+++ b/include/configs/stxxtc.h
@@ -592,9 +592,6 @@ typedef unsigned int led_id_t;
 /* pass open firmware flat tree */
 #define CONFIG_OF_FLAT_TREE	1
 
-/* maximum size of the flat tree (8K) */
-#define OF_FLAT_TREE_MAX_SIZE	8192
-
 #define OF_CPU			"PowerPC,MPC870@0"
 #define OF_TBCLK		(MPC8XX_HZ / 16)
 #define CONFIG_OF_HAS_BD_T	1
diff --git a/include/configs/trizepsiv.h b/include/configs/trizepsiv.h
new file mode 100644
index 0000000..84998d4
--- /dev/null
+++ b/include/configs/trizepsiv.h
@@ -0,0 +1,325 @@
+/*
+ * (C) Copyright 2007
+ * Stefano Babic, DENX Gmbh, sbabic@denx.de
+ *
+ * (C) Copyright 2004
+ * Robert Whaley, Applied Data Systems, Inc. rwhaley@applieddata.net
+ *
+ * (C) Copyright 2002
+ * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
+ *
+ * (C) Copyright 2002
+ * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
+ * Marius Groeger <mgroeger@sysgo.de>
+ *
+ * Configuation settings for the LUBBOCK board.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#define CONFIG_PXA27X		1	/* This is an PXA27x CPU    */
+
+#define LITTLEENDIAN		1	/* used by usb_ohci.c		*/
+
+#define CONFIG_MMC		1
+#define BOARD_LATE_INIT		1
+
+#undef CONFIG_USE_IRQ			/* we don't need IRQ/FIQ stuff */
+
+#define RTC
+
+/*
+ * Size of malloc() pool
+ */
+#define CFG_MALLOC_LEN	    (CFG_ENV_SIZE + 128*1024)
+#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+
+/*
+ * Hardware drivers
+ */
+
+/*
+ * select serial console configuration
+ */
+#define CONFIG_SERIAL_MULTI
+#define CONFIG_FFUART	       1       /* we use FFUART on Conxs */
+#define CONFIG_BTUART	       1       /* we use BTUART on Conxs */
+#define CONFIG_STUART	       1       /* we use STUART on Conxs */
+
+/* allow to overwrite serial and ethaddr */
+#define CONFIG_ENV_OVERWRITE
+
+#define CONFIG_BAUDRATE	       38400
+
+#define CONFIG_DOS_PARTITION   1
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_IMLS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_USB
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+
+#undef CONFIG_SHOW_BOOT_PROGRESS
+
+#define CONFIG_BOOTDELAY	3
+#define CONFIG_SERVERIP		192.168.1.99
+#define CONFIG_BOOTCOMMAND	"run boot_flash"
+#define CONFIG_BOOTARGS		"console=ttyS0,38400 ramdisk_size=12288"\
+				" rw root=/dev/ram initrd=0xa0800000,5m"
+
+#define CONFIG_EXTRA_ENV_SETTINGS					\
+	"program_boot_mmc="						\
+			"mw.b 0xa0010000 0xff 0x20000; "		\
+			"if	 mmcinit && "				\
+				"fatload mmc 0 0xa0010000 u-boot.bin; "	\
+			"then "						\
+				"protect off 0x0 0x1ffff; "		\
+				"erase 0x0 0x1ffff; "			\
+				"cp.b 0xa0010000 0x0 0x20000; "		\
+			"fi\0"						\
+	"program_uzImage_mmc="						\
+			"mw.b 0xa0010000 0xff 0x180000; "		\
+			"if	 mmcinit && "				\
+				"fatload mmc 0 0xa0010000 uzImage; "	\
+			"then "						\
+				"protect off 0x40000 0x1bffff; "	\
+				"erase 0x40000 0x1bffff; "		\
+				"cp.b 0xa0010000 0x40000 0x180000; "	\
+			"fi\0"						\
+	"program_ramdisk_mmc="						\
+			"mw.b 0xa0010000 0xff 0x500000; "		\
+			"if	 mmcinit && "				\
+				"fatload mmc 0 0xa0010000 ramdisk.gz; "	\
+			"then "						\
+				"protect off 0x1c0000 0x6bffff; "	\
+				"erase 0x1c0000 0x6bffff; "		\
+				"cp.b 0xa0010000 0x1c0000 0x500000; "	\
+			"fi\0"						\
+	"boot_mmc="							\
+			"if	 mmcinit && "				\
+				"fatload mmc 0 0xa0030000 uzImage && "	\
+				"fatload mmc 0 0xa0800000 ramdisk.gz; "	\
+			"then "						\
+				"bootm 0xa0030000; "			\
+			"fi\0"						\
+	"boot_flash="							\
+			"cp.b 0x1c0000 0xa0800000 0x500000; "		\
+			"bootm 0x40000\0"				\
+
+#define CONFIG_SETUP_MEMORY_TAGS 1
+#define CONFIG_CMDLINE_TAG	 1	/* enable passing of ATAGs	*/
+/* #define CONFIG_INITRD_TAG	 1 */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use */
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_HUSH_PARSER		1
+#define CFG_PROMPT_HUSH_PS2	"> "
+
+#define CFG_LONGHELP				/* undef to save memory		*/
+#ifdef CFG_HUSH_PARSER
+#define CFG_PROMPT		"$ "		/* Monitor Command Prompt */
+#else
+#define CFG_PROMPT		"=> "		/* Monitor Command Prompt */
+#endif
+#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS		16		/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_DEVICE_NULLDEV	1
+
+#define CFG_MEMTEST_START	0xa0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END		0xa0800000	/* 4 ... 8 MB in DRAM	*/
+
+#undef	CFG_CLKS_IN_HZ		/* everything, incl board info, in Hz */
+
+#define CFG_LOAD_ADDR		0xa1000000	/* default load address */
+
+#define CFG_HZ			3686400		/* incrementer freq: 3.6864 MHz */
+#define CFG_CPUSPEED		0x207		/* need to look more closely, I think this is Turbo = 2x, L=91Mhz */
+
+						/* valid baudrates */
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_MMC_BASE		0xF0000000
+
+/*
+ * Stack sizes
+ *
+ * The stack sizes are set up in start.S using the settings below
+ */
+#define CONFIG_STACKSIZE	(128*1024)	/* regular stack */
+#ifdef CONFIG_USE_IRQ
+#define CONFIG_STACKSIZE_IRQ	(4*1024)	/* IRQ stack */
+#define CONFIG_STACKSIZE_FIQ	(4*1024)	/* FIQ stack */
+#endif
+
+/*
+ * Physical Memory Map
+ */
+#define CONFIG_NR_DRAM_BANKS	4	   /* we have 2 banks of DRAM */
+#define PHYS_SDRAM_1		0xa0000000 /* SDRAM Bank #1 */
+#define PHYS_SDRAM_1_SIZE	0x04000000 /* 64 MB */
+#define PHYS_SDRAM_2		0xa4000000 /* SDRAM Bank #2 */
+#define PHYS_SDRAM_2_SIZE	0x00000000 /* 0 MB */
+#define PHYS_SDRAM_3		0xa8000000 /* SDRAM Bank #3 */
+#define PHYS_SDRAM_3_SIZE	0x00000000 /* 0 MB */
+#define PHYS_SDRAM_4		0xac000000 /* SDRAM Bank #4 */
+#define PHYS_SDRAM_4_SIZE	0x00000000 /* 0 MB */
+
+#define PHYS_FLASH_1		0x00000000 /* Flash Bank #1 */
+
+#define CFG_DRAM_BASE		0xa0000000
+#define CFG_DRAM_SIZE		0x04000000
+
+#define CFG_FLASH_BASE		PHYS_FLASH_1
+
+/*
+ * GPIO settings
+ */
+#define CFG_GPSR0_VAL		0x00018000
+#define CFG_GPSR1_VAL		0x00000000
+#define CFG_GPSR2_VAL		0x400dc000
+#define CFG_GPSR3_VAL		0x00000000
+#define CFG_GPCR0_VAL		0x00000000
+#define CFG_GPCR1_VAL		0x00000000
+#define CFG_GPCR2_VAL		0x00000000
+#define CFG_GPCR3_VAL		0x00000000
+#define CFG_GPDR0_VAL		0x00018000
+#define CFG_GPDR1_VAL		0x00028801
+#define CFG_GPDR2_VAL		0x520dc000
+#define CFG_GPDR3_VAL		0x0001E000
+#define CFG_GAFR0_L_VAL		0x801c0000
+#define CFG_GAFR0_U_VAL		0x00000013
+#define CFG_GAFR1_L_VAL		0x6990100A
+#define CFG_GAFR1_U_VAL		0x00000008
+#define CFG_GAFR2_L_VAL		0xA0000000
+#define CFG_GAFR2_U_VAL		0x010900F2
+#define CFG_GAFR3_L_VAL		0x54000003
+#define CFG_GAFR3_U_VAL		0x00002401
+#define CFG_GRER0_VAL		0x00000000
+#define CFG_GRER1_VAL		0x00000000
+#define CFG_GRER2_VAL		0x00000000
+#define CFG_GRER3_VAL		0x00000000
+#define CFG_GFER0_VAL		0x00000000
+#define CFG_GFER1_VAL		0x00000000
+#define CFG_GFER2_VAL		0x00000000
+#define CFG_GFER3_VAL		0x00000020
+
+
+#define CFG_PSSR_VAL		0x20	/* CHECK */
+
+/*
+ * Clock settings
+ */
+#define CFG_CKEN		0x01FFFFFF	/* CHECK */
+#define CFG_CCCR		0x02000290 /*   520Mhz */
+
+/*
+ * Memory settings
+ */
+
+#define CFG_MSC0_VAL		0x4df84df0
+#define CFG_MSC1_VAL		0x7ff87ff4
+#define CFG_MSC2_VAL		0xa26936d4
+#define CFG_MDCNFG_VAL		0x880009C9
+#define CFG_MDREFR_VAL		0x20ca201e
+#define CFG_MDMRS_VAL		0x00220022
+
+#define CFG_FLYCNFG_VAL		0x00000000
+#define CFG_SXCNFG_VAL		0x40044004
+
+/*
+ * PCMCIA and CF Interfaces
+ */
+#define CFG_MECR_VAL		0x00000001
+#define CFG_MCMEM0_VAL		0x00004204
+#define CFG_MCMEM1_VAL		0x00010204
+#define CFG_MCATT0_VAL		0x00010504
+#define CFG_MCATT1_VAL		0x00010504
+#define CFG_MCIO0_VAL		0x00008407
+#define CFG_MCIO1_VAL		0x0000c108
+
+#define CONFIG_DRIVER_DM9000		1
+#define CONFIG_DRIVER_DM9000		1
+#define CONFIG_DM9000_BASE	0x08000000
+#define DM9000_IO			CONFIG_DM9000_BASE
+#define DM9000_DATA			(CONFIG_DM9000_BASE+0x8004)
+/* #define CONFIG_DM9000_USE_8BIT */
+/* #define CONFIG_DM9000_USE_16BIT */
+#define CONFIG_DM9000_USE_32BIT
+
+#define CONFIG_USB_OHCI_NEW	1
+#define CFG_USB_OHCI_BOARD_INIT	1
+#define CFG_USB_OHCI_MAX_ROOT_PORTS	3
+#define CFG_USB_OHCI_REGS_BASE	0x4C000000
+#define CFG_USB_OHCI_SLOT_NAME	"trizepsiv"
+#define CONFIG_USB_STORAGE	1
+#define CFG_USB_OHCI_CPU_INIT	1
+
+/*
+ * FLASH and environment organization
+ */
+
+#define CFG_FLASH_CFI
+#define CFG_FLASH_CFI_DRIVER	1
+
+#define CFG_MONITOR_BASE	0
+#define CFG_MONITOR_LEN		0x40000
+
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	4 + 255  /* max number of sectors on one chip    */
+
+/* timeout values are in ticks */
+#define CFG_FLASH_ERASE_TOUT	(25*CFG_HZ) /* Timeout for Flash Erase */
+#define CFG_FLASH_WRITE_TOUT	(25*CFG_HZ) /* Timeout for Flash Write */
+
+/* write flash less slowly */
+#define CFG_FLASH_USE_BUFFER_WRITE 1
+
+/* Flash environment locations */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(PHYS_FLASH_1 + CFG_MONITOR_LEN)	/* Addr of Environment Sector	*/
+#define CFG_ENV_SIZE		0x40000	/* Total Size of Environment     	*/
+#define CFG_ENV_SECT_SIZE	0x40000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR+CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/uc101.h b/include/configs/uc101.h
index 3b471d0..aed80ec 100644
--- a/include/configs/uc101.h
+++ b/include/configs/uc101.h
@@ -332,7 +332,6 @@
 #define CFG_IDE_MAXDEVICE	2	/* max. 2 drives per IDE bus	*/
 
 #define CONFIG_IDE_PREINIT	1
-/* #define CONFIG_IDE_RESET	1 beispile siehe tqm5200.c */
 
 #define CFG_ATA_IDE0_OFFSET	0x0000
 
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index 9c536fd..74033b4 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -46,7 +46,6 @@
 #define EXTCLK_83		83333333
 
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
-#define CONFIG_ADD_RAM_INFO	1	/* Print additional info	*/
 #undef  CONFIG_SHOW_BOOT_PROGRESS
 #undef  CONFIG_STRESS
 
@@ -69,11 +68,11 @@
 #define CFG_PCIE_BASE		0xe0000000	/* PCIe UTL regs */
 
 #define CFG_PCIE0_CFGBASE	0xc0000000
-#define CFG_PCIE0_XCFGBASE	0xc0000400
-#define CFG_PCIE1_CFGBASE	0xc0001000
-#define CFG_PCIE1_XCFGBASE	0xc0001400
-#define CFG_PCIE2_CFGBASE	0xc0002000
-#define CFG_PCIE2_XCFGBASE	0xc0002400
+#define CFG_PCIE1_CFGBASE	0xc1000000
+#define CFG_PCIE2_CFGBASE	0xc2000000
+#define CFG_PCIE0_XCFGBASE	0xc3000000
+#define CFG_PCIE1_XCFGBASE	0xc3001000
+#define CFG_PCIE2_XCFGBASE	0xc3002000
 
 /* System RAM mapped to PCI space */
 #define CONFIG_PCI_SYS_MEM_BUS	CFG_SDRAM_BASE
@@ -183,6 +182,7 @@
 		"cp.b ${fileaddr} FFFB0000 ${filesize};"		\
 		"setenv filesize;saveenv\0"				\
 	"upd=run load;run update\0"					\
+	"pciconfighost=1\0"						\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
@@ -298,7 +298,7 @@
 #define CONFIG_PCI			/* include pci support		*/
 #define CONFIG_PCI_PNP		1	/* do pci plug-and-play		*/
 #define CONFIG_PCI_SCAN_SHOW	1	/* show pci devices on startup	*/
-#undef CONFIG_PCI_CONFIG_HOST_BRIDGE
+#define CONFIG_PCI_CONFIG_HOST_BRIDGE
 
 /* Board-specific PCI */
 #define CFG_PCI_TARGET_INIT		/* let board init pci target    */