ppc4xx: Remove AP1000 board support

As the board seems to be unmaintained for some time, lets remove
the support in mainline completely.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: James MacAulay <james.macaulay@amirix.com>
Acked-by: Marek Vasut <marex@denx.de>

1 files changed, 0 insertions, 247 deletions

diff --git a/include/configs/AP1000.h b/include/configs/AP1000.h
deleted file mode 100644
index 09cfef6..0000000
--- a/include/configs/AP1000.h
+++ /dev/null
@@ -1,247 +0,0 @@
-/*
- * AMIRIX.h: AMIRIX specific config options
- *
- * Author : Frank Smith (smith at amirix dot com)
- *
- * Derived from : other configuration header files in this tree
- *
- * This software may be used and distributed according to the terms of
- * the GNU General Public License (GPL) version 2, incorporated herein by
- * reference. Drivers based on or derived from this code fall under the GPL
- * and must retain the authorship, copyright and this license notice. This
- * file is not a complete program and may only be used when the entire
- * program is licensed under the GPL.
- *
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_405	1		/* This is a PPC405 CPU	    */
-#define CONFIG_4xx	1		/* ...member of PPC4xx family	*/
-
-#define CONFIG_AP1000	1		/* ...on an AP1000 board    */
-
-/*
- * Start at bottom of RAM, but at an aliased address so that it looks
- * like it's not in RAM.  This is a bit of voodoo to allow it to be
- * run from RAM instead of Flash.
- */
-#define	CONFIG_SYS_TEXT_BASE	0x08000000
-#define CONFIG_SYS_LDSCRIPT	"board/amirix/ap1000/u-boot.lds"
-
-#define CONFIG_PCI	1
-
-#define CONFIG_SYS_HUSH_PARSER 1		/* use "hush" command parser	*/
-#define CONFIG_SYS_PROMPT		"0> "
-
-#define CONFIG_COMMAND_EDIT	1
-#define CONFIG_COMPLETE_ADDRESSES 1
-
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#undef CONFIG_ENV_IS_IN_FLASH
-#else
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#undef CONFIG_ENV_IS_IN_NVRAM
-#endif
-#endif
-
-#define CONFIG_BAUDRATE		57600
-#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds */
-
-#define CONFIG_BOOTCOMMAND	""	/* autoboot command */
-
-#define CONFIG_BOOTARGS		"console=ttyS0,57600"
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MVENV
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled	    */
-
-#define CONFIG_SYS_CLK_FREQ	30000000
-
-#define CONFIG_SPD_EEPROM	1	/* use SPD EEPROM for setup    */
-
-/*
- * I2C
- */
-#define CONFIG_HARD_I2C			/* I2C with hardware support	*/
-#define CONFIG_PPC4XX_I2C		/* use PPC4xx driver		*/
-#define CONFIG_SYS_I2C_SLAVE	0x7F
-#define CONFIG_SYS_I2C_SPEED	400000
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-/* usually: (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) */
-#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE+4+16)	/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_ALT_MEMTEST		1
-#define CONFIG_SYS_MEMTEST_START	0x00400000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x01000000	/* 4 ... 16 MB in DRAM	*/
-
-/*
- * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
- * The Linux BASE_BAUD define should match this configuration.
- *    baseBaud = cpuClock/(uartDivisor*16)
- * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
- * set Linux BASE_BAUD to 403200.
- */
-#undef	CONFIG_SYS_EXT_SERIAL_CLOCK		/* external serial clock */
-#undef	CONFIG_SYS_405_UART_ERRATA_59		/* 405GP/CR Rev. D silicon */
-
-#define CONFIG_SYS_NS16550_CLK		40000000
-#define CONFIG_SYS_DUART_CHAN		0
-#define CONFIG_SYS_NS16550_COM1	(0x4C000000 + 0x1000)
-#define CONFIG_SYS_NS16550_COM2	(0x4C800000 + 0x1000)
-#define CONFIG_SYS_NS16550_REG_SIZE	4
-#define CONFIG_SYS_NS16550		1
-#define CONFIG_SYS_INIT_CHAN1		1
-#define CONFIG_SYS_INIT_CHAN2		0
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CONFIG_SYS_LOAD_ADDR		0x00200000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO		1		/* To use extended board_into (bd_t) */
-
-#define CONFIG_SYS_HZ			1000		/* decrementer freq: 1 ms ticks */
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0x20000000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_MONITOR_LEN		(192 * 1024)	/* Reserve 196 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_FLASH_CFI		1
-#define CONFIG_SYS_PROGFLASH_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CONFFLASH_BASE	0x24000000
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks	    */
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)  */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#define CONFIG_SYS_FLASH_PROTECTION	1	/* use hardware protection	    */
-
-/* BEG ENVIRONNEMENT FLASH */
-#ifdef CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OFFSET		0x00040000 /* Offset of Environment Sector	*/
-#define CONFIG_ENV_SIZE		0x1000	/* Total Size of Environment Sector */
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* see README - env sector total size	*/
-#endif
-/* END ENVIRONNEMENT FLASH */
-/*-----------------------------------------------------------------------
- * NVRAM organization
- */
-#define CONFIG_SYS_NVRAM_BASE_ADDR	0xf0000000	/* NVRAM base address	*/
-#define CONFIG_SYS_NVRAM_SIZE		0x1ff8		/* NVRAM size	*/
-
-#ifdef CONFIG_ENV_IS_IN_NVRAM
-#define CONFIG_ENV_SIZE		0x1000		/* Size of Environment vars */
-#define CONFIG_ENV_ADDR	    \
-    (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE)	/* Env	*/
-#endif
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/
-
-/* Configuration Port location */
-#define CONFIG_PORT_ADDR	0xF0000500
-
-/*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in DPRAM)
- */
-
-#define CONFIG_SYS_INIT_RAM_ADDR	0x400000  /* inside of SDRAM			 */
-#define CONFIG_SYS_INIT_RAM_SIZE	0x2000	/* Size of used area in RAM	       */
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
- * Definitions for Serial Presence Detect EEPROM address
- * (to get SDRAM settings)
- */
-#define SPD_EEPROM_ADDRESS	0x50
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* JFFS2 stuff */
-
-#define CONFIG_SYS_JFFS2_FIRST_BANK	0
-#define CONFIG_SYS_JFFS2_NUM_BANKS	1
-#define CONFIG_SYS_JFFS2_FIRST_SECTOR	1
-
-#define CONFIG_E1000
-
-#define CONFIG_SYS_ETH_DEV_FN		0x0800
-#define CONFIG_SYS_ETH_IOBASE		0x31000000
-#define CONFIG_SYS_ETH_MEMBASE		0x32000000
-
-#endif	/* __CONFIG_H */