Merge with git://www.denx.de/git/u-boot.git

14 files changed, 1037 insertions, 205 deletions

diff --git a/include/configs/IceCube.h b/include/configs/IceCube.h
index c380c54..6c6480d 100644
--- a/include/configs/IceCube.h
+++ b/include/configs/IceCube.h
@@ -189,7 +189,7 @@
 
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
-#define OF_TBCLK		(bd->bi_busfreq / 8)
+#define OF_TBCLK		(bd->bi_busfreq / 4)
 #define OF_STDOUT_PATH		"/soc5200@f0000000/serial@2000"
 
 /*
diff --git a/include/configs/MPC8360EMDS.h b/include/configs/MPC8360EMDS.h
index d2af0e1..79937dc 100644
--- a/include/configs/MPC8360EMDS.h
+++ b/include/configs/MPC8360EMDS.h
@@ -342,8 +342,12 @@
 #endif
 
 /* pass open firmware flat tree */
-#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_LIBFDT	1
+#undef  CONFIG_OF_FLAT_TREE
 #define CONFIG_OF_BOARD_SETUP	1
+#define CONFIG_OF_HAS_BD_T	1
+#define CONFIG_OF_HAS_UBOOT_ENV	1
+
 
 /* maximum size of the flat tree (8K) */
 #define OF_FLAT_TREE_MAX_SIZE	8192
diff --git a/include/configs/NC650.h b/include/configs/NC650.h
index 8da29c4..a12c8da 100644
--- a/include/configs/NC650.h
+++ b/include/configs/NC650.h
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2006 Detlev Zundel, dzu@denx.de
+ * (C) Copyright 2006, 2007 Detlev Zundel, dzu@denx.de
  * (C) Copyright 2005
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
@@ -237,18 +237,8 @@
 /*
  * NAND flash support
  */
-#define CFG_NAND_LEGACY
-
 #define CFG_MAX_NAND_DEVICE	1
-#define NAND_ChipID_UNKNOWN	0x00
-#define SECTORSIZE		512
-#define NAND_MAX_FLOORS		1
 #define NAND_MAX_CHIPS		1
-#define ADDR_PAGE		2
-#define ADDR_COLUMN_PAGE	3
-#define ADDR_COLUMN		1
-#define NAND_NO_RB
-
 
 /*-----------------------------------------------------------------------
  * SYPCR - System Protection Control					11-9
diff --git a/include/configs/acadia.h b/include/configs/acadia.h
index 9e02ca3..35b6a51 100644
--- a/include/configs/acadia.h
+++ b/include/configs/acadia.h
@@ -31,20 +31,18 @@
 /*-----------------------------------------------------------------------
  * High Level Configuration Options
  *----------------------------------------------------------------------*/
-#define CONFIG_ACADIA			1	/* Board is Acadia	*/
-#define CONFIG_4xx			1	/* ... PPC4xx family	*/
-#define CONFIG_405EZ			1	/* Specifc 405EZ support*/
-#undef	CFG_DRAM_TEST				/* Disable-takes long time */
+#define CONFIG_ACADIA		1		/* Board is Acadia	*/
+#define CONFIG_4xx		1		/* ... PPC4xx family	*/
+#define CONFIG_405EZ		1		/* Specifc 405EZ support*/
 #define CONFIG_SYS_CLK_FREQ	66666666	/* external freq to pll	*/
 
-#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_pre_init		*/
-#define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
+#define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
+#define CONFIG_MISC_INIT_F	1		/* Call misc_init_f	*/
 
 #define CONFIG_NO_SERIAL_EEPROM
 /*#undef CONFIG_NO_SERIAL_EEPROM*/
 
 #ifdef CONFIG_NO_SERIAL_EEPROM
-
 /*----------------------------------------------------------------------------
  * PLL settings for 266MHz CPU, 133MHz PLB/SDRAM, 66MHz EBC, 33MHz PCI,
  * assuming a 66MHz input clock to the 405EZ.
@@ -59,24 +57,125 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_FLASH_BASE		0xFE000000
 #define CFG_MONITOR_LEN		(256 * 1024)/* Reserve 256 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(384 * 1024)/* Reserve 128 kB for malloc()	*/
+#define CFG_MALLOC_LEN		(512 * 1024)/* Reserve 512 kB for malloc()	*/
+
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		0xfe000000
 #define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_CPLD_BASE		0x80000000
+#define CFG_NAND_ADDR		0xd0000000
 #define CFG_USB_HOST		0xef603000	/* USB OHCI 1.1 controller	*/
 
-/*
- * Define here the location of the environment variables (FLASH).
- * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
- *       supported for backward compatibility.
- */
+/*-----------------------------------------------------------------------
+ * Initial RAM & stack pointer
+ *----------------------------------------------------------------------*/
+#define CFG_TEMP_STACK_OCM	1		/* OCM as init ram	*/
+
+/* On Chip Memory location */
+#define CFG_OCM_DATA_ADDR	0xF8000000
+#define CFG_OCM_DATA_SIZE	0x4000			/* 16K of onchip SRAM		*/
+#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR	/* inside of SRAM		*/
+#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE	/* End of used area in RAM	*/
+
+#define CFG_GBL_DATA_SIZE	128			/* size for initial data	*/
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Serial Port
+ *----------------------------------------------------------------------*/
+#undef	CFG_EXT_SERIAL_CLOCK			/* external serial clock */
+#define CFG_BASE_BAUD		691200
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SERIAL_MULTI     1
+
+/* The following table includes the supported baudrates */
+#define CFG_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+/*-----------------------------------------------------------------------
+ * Environment
+ *----------------------------------------------------------------------*/
 #if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
-   #define CFG_ENV_IS_IN_FLASH	1 		/* use FLASH for environment vars	*/
+#define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars	*/
 #else
-   #define CFG_ENV_IS_IN_NAND	1		/* use NAND for environment vars	*/
+#define CFG_ENV_IS_IN_NAND	1	/* use NAND for environment vars	*/
+#define CFG_ENV_IS_EMBEDDED	1	/* use embedded environment */
 #endif
 
+/*-----------------------------------------------------------------------
+ * FLASH related
+ *----------------------------------------------------------------------*/
+#define CFG_FLASH_CFI			/* The flash is CFI compatible	*/
+#define CFG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/
+
+#define CFG_FLASH_BANKS_LIST    {CFG_FLASH_BASE}
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
+
+#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+
+#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+
+#ifdef CFG_ENV_IS_IN_FLASH
+#define CFG_ENV_SECT_SIZE	0x40000 /* size of one complete sector	*/
+#define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
+#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
+
+/* Address and size of Redundant Environment Sector	*/
+#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#endif
+
+/*-----------------------------------------------------------------------
+ * RAM (CRAM)
+ *----------------------------------------------------------------------*/
+#define CFG_MBYTES_RAM		64		/* 64MB			*/
+
+/*-----------------------------------------------------------------------
+ * I2C
+ *----------------------------------------------------------------------*/
+#define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
+#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
+#define CFG_I2C_SPEED		400000		/* I2C speed and slave address	*/
+#define CFG_I2C_SLAVE		0x7F
+
+#define CFG_I2C_MULTI_EEPROMS
+#define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_ENABLE
+#define CFG_EEPROM_PAGE_WRITE_BITS 3
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/* I2C SYSMON (LM75, AD7414 is almost compatible)			*/
+#define CONFIG_DTT_LM75		1		/* ON Semi's LM75	*/
+#define CONFIG_DTT_AD7414	1		/* use AD7414		*/
+#define CONFIG_DTT_SENSORS	{0}		/* Sensor addresses	*/
+#define CFG_DTT_MAX_TEMP	70
+#define CFG_DTT_LOW_TEMP	-30
+#define CFG_DTT_HYSTERESIS	3
+
+#if 0 /* test-only... */
+/*-----------------------------------------------------------------------
+ * SPI stuff - Define to include SPI control
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_SPI
+#endif
+
+/*-----------------------------------------------------------------------
+ * Ethernet
+ *----------------------------------------------------------------------*/
+#define CONFIG_MII		1	/* MII PHY management		*/
+#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_NET_MULTI	1
+#define CFG_RX_ETH_BUFFER	16	/* # of rx buffers & descriptors*/
+
+#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
+
 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
 	"echo"
@@ -122,13 +221,6 @@
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
-#define CONFIG_NET_MULTI	1
-#define CFG_RX_ETH_BUFFER	16	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-
 #define CONFIG_USB_OHCI
 #define CONFIG_USB_STORAGE
 
@@ -166,7 +258,6 @@
 			       CFG_CMD_PCI	|	\
 			       CFG_CMD_PING	|	\
 			       CFG_CMD_REGINFO	|	\
-			       CFG_CMD_SDRAM	|	\
 			       CFG_CMD_USB)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
@@ -174,76 +265,34 @@
 
 #undef CONFIG_WATCHDOG					/* watchdog disabled		*/
 
-/*
+/*-----------------------------------------------------------------------
  * Miscellaneous configurable options
- */
+ *----------------------------------------------------------------------*/
 #define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	        16	/* max number of command args	*/
+#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
 
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
 
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
+#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
 #define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command		*/
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands	*/
+#define CONFIG_LOOPW            1       /* enable loopw command         */
+#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 #define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
-/*-----------------------------------------------------------------------
- * Serial Port
- *----------------------------------------------------------------------*/
-#undef	CFG_EXT_SERIAL_CLOCK			/* external serial clock */
-#define CFG_BASE_BAUD		691200
-#define CONFIG_BAUDRATE		115200
-
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-/*-----------------------------------------------------------------------
- * I2C
- *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
-
-#define CFG_I2C_MULTI_EEPROMS
-#define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
-#define CFG_I2C_EEPROM_ADDR_LEN 1
-#define CFG_EEPROM_PAGE_WRITE_ENABLE
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
-
-/* I2C SYSMON (LM75, AD7414 is almost compatible)			*/
-#define CONFIG_DTT_LM75		1		/* ON Semi's LM75	*/
-#define CONFIG_DTT_AD7414	1		/* use AD7414		*/
-#define CONFIG_DTT_SENSORS	{0}		/* Sensor addresses	*/
-#define CFG_DTT_MAX_TEMP	70
-#define CFG_DTT_LOW_TEMP	-30
-#define CFG_DTT_HYSTERESIS	3
-
-#if 0 /* test-only... */
-/*-----------------------------------------------------------------------
- * SPI stuff - Define to include SPI control
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SPI
-#endif
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
@@ -251,39 +300,13 @@
  */
 #define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
-/*-----------------------------------------------------------------------
- * FLASH related
- *----------------------------------------------------------------------*/
-#define CFG_FLASH_CFI
-#define CFG_FLASH_CFI_DRIVER
-#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
-
-#define CFG_FLASH_BANKS_LIST    {CFG_FLASH_BASE}
-#define CFG_MAX_FLASH_BANKS     1		    /* number of banks	    */
-#define CFG_MAX_FLASH_SECT	1024		    /* sectors per device   */
-
-#undef	CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-#ifdef CFG_ENV_IS_IN_FLASH
-#define CFG_ENV_SECT_SIZE	0x40000 /* size of one complete sector	*/
-#define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
-#define	CFG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/
-
-/* Address and size of Redundant Environment Sector	*/
-#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR-CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
-#endif
-
 #ifdef TEST_ONLY_NAND
 /*-----------------------------------------------------------------------
  * NAND FLASH
  *----------------------------------------------------------------------*/
 #define CFG_MAX_NAND_DEVICE	1
 #define NAND_MAX_CHIPS		1
-#define CFG_NAND_BASE		(CFG_NAND + CFG_NAND_CS)
+#define CFG_NAND_BASE		(CFG_NAND_ADDR + CFG_NAND_CS)
 #define CFG_NAND_SELECT_DEVICE  1	/* nand driver supports mutipl. chips	*/
 #endif
 
@@ -297,50 +320,42 @@
 #endif
 
 /*-----------------------------------------------------------------------
- * Definitions for initial stack pointer and data area (in data cache)
- */
-/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM	1
-
-/* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR	0xF8000000
-#define CFG_OCM_DATA_SIZE	0x4000			/* 16K of onchip SRAM		*/
-#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR	/* inside of SRAM		*/
-#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE	/* End of used area in RAM	*/
-
-#define CFG_GBL_DATA_SIZE	128			/* size for initial data	*/
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
-
-/*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
- */
-#define CFG_NAND		0xd0000000
+ *----------------------------------------------------------------------*/
 #define CFG_NAND_CS		0		/* NAND chip connected to CSx	*/
 
-/* Memory Bank 0 (Flash) initialization */
+/* Memory Bank 0 (Flash) initialization						*/
 #define CFG_EBC_PB0AP		0x03337200
-#define CFG_EBC_PB0CR		0xfe0bc000 	/* BAS=0xFE0,BS=32MB,BU=R/W,BW=32bit	*/
+#define CFG_EBC_PB0CR		0xfe0bc000
 
-/* Memory Bank 1 (CRAM) initialization */
+/* Just initial configuration for CRAM. Will be changed in memory.c to sync mode*/
+/* Memory Bank 1 (CRAM) initialization						*/
 #define CFG_EBC_PB1AP		0x030400c0
 #define CFG_EBC_PB1CR		0x000bc000
 
-/* Memory Bank 2 (CRAM) initialization */
+/* Memory Bank 2 (CRAM) initialization						*/
 #define CFG_EBC_PB2AP		0x030400c0
 #define CFG_EBC_PB2CR		0x020bc000
 
 /* Memory Bank 3 (NAND-FLASH) initialization					*/
 #define CFG_EBC_PB3AP		0x018003c0
-#define CFG_EBC_PB3CR		(CFG_NAND | 0x1c000)
+#define CFG_EBC_PB3CR		(CFG_NAND_ADDR | 0x1c000)
 
-/* Memory Bank 4 (CPLD) initialization */
+/* Memory Bank 4 (CPLD) initialization						*/
 #define CFG_EBC_PB4AP		0x04006000
-#define CFG_EBC_PB4CR		0x80018000 	/* BAS=0x000,BS=16MB,BU=R/W,BW=32bit	*/
+#define CFG_EBC_PB4CR		(CFG_CPLD_BASE | 0x18000)
 
 #define CFG_EBC_CFG		0xf8400000
 
 /*-----------------------------------------------------------------------
+ * GPIO Setup
+ *----------------------------------------------------------------------*/
+#define CFG_GPIO_CRAM_CLK	8
+#define CFG_GPIO_CRAM_WAIT	9
+#define CFG_GPIO_CRAM_ADV	10
+#define CFG_GPIO_CRAM_CRE	(32 + 21)
+
+/*-----------------------------------------------------------------------
  * Definitions for GPIO_0 setup (PPC405EZ specific)
  *
  * GPIO0[0-3]	- External Bus Controller CS_4 - CS_7 Outputs
@@ -389,25 +404,6 @@
 #define CFG_GPIO1_TSRL		0x00000000
 #define CFG_GPIO1_TCR		0xFFFF8014
 
-/*-----------------------------------------------------------------------
- * EPLD Regs.
- */
-#define	EPLD_BASE	0x80000000
-#define	EPLD_ETHRSTBOOT	0x10
-#define	EPLD_CTRL	0x14
-#define	EPLD_MUXOE	0x16
-
-/*
- * State definations
- */
-#define	LOAK_INIT	0x494e4954	/* ASCII "INIT" */
-#define	LOAK_NONE	0x4e4f4e45	/* ASCII "NONE" */
-#define	LOAK_CRAM	0x4352414d	/* ASCII "CRAM" */
-#define	LOAK_PSRAM	0x50535241	/* ASCII "PSRA" - PSRAM */
-#define	LOAK_OCM	0x4f434d20	/* ASCII "OCM " */
-#define	LOAK_ZERO	0x5a45524f	/* ASCII "ZERO" */
-#define	LOAK_SPL	0x53504c20	/* ASCII "SPL" */
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/atstk1002.h b/include/configs/atstk1002.h
index 458ebab..beaf385 100644
--- a/include/configs/atstk1002.h
+++ b/include/configs/atstk1002.h
@@ -62,11 +62,14 @@
  */
 #define CFG_PLL0_OPT			0x04
 
-#define CFG_USART1			1
-
-#define CFG_CONSOLE_UART_DEV		DEVICE_USART1
+#undef CONFIG_USART0
+#define CONFIG_USART1			1
+#undef CONFIG_USART2
+#undef CONFIG_USART3
 
 /* User serviceable stuff */
+#define CONFIG_DOS_PARTITION		1
+
 #define CONFIG_CMDLINE_TAG		1
 #define CONFIG_SETUP_MEMORY_TAGS	1
 #define CONFIG_INITRD_TAG		1
@@ -75,16 +78,47 @@
 
 #define CONFIG_BAUDRATE			115200
 #define CONFIG_BOOTARGS							\
-	"console=ttyUS0 root=/dev/mtdblock1 fbmem=600k"
+	"console=ttyS0 root=/dev/mtdblock1 rootfstype=jffs2 fbmem=600k"
+
+#define CONFIG_BOOTCOMMAND						\
+	"fsload; bootm $(fileaddr)"
+
+/*
+ * Only interrupt autoboot if <space> is pressed. Otherwise, garbage
+ * data on the serial line may interrupt the boot sequence.
+ */
+#define CONFIG_BOOTDELAY		2
+#define CONFIG_AUTOBOOT			1
+#define CONFIG_AUTOBOOT_KEYED		1
+#define CONFIG_AUTOBOOT_PROMPT				\
+	"Press SPACE to abort autoboot in %d seconds\n"
+#define CONFIG_AUTOBOOT_DELAY_STR	"d"
+#define CONFIG_AUTOBOOT_STOP_STR	" "
+
+/*
+ * These are "locally administered ethernet addresses" generated by
+ * ./tools/gen_eth_addr
+ *
+ * After booting the board for the first time, new addresses should be
+ * generated and assigned to the environment variables "ethaddr" and
+ * "eth1addr".
+ */
+#define CONFIG_ETHADDR			"6a:87:71:14:cd:cb"
+#define CONFIG_ETH1ADDR			"ca:f8:15:e6:3e:e6"
+#define CONFIG_OVERWRITE_ETHADDR_ONCE	1
+#define CONFIG_NET_MULTI		1
+
+#define CONFIG_BOOTP_MASK		(CONFIG_BOOTP_SUBNETMASK	\
+					 | CONFIG_BOOTP_GATEWAY)
 
 #define CONFIG_COMMANDS			(CFG_CMD_BDI			\
 					 | CFG_CMD_LOADS		\
 					 | CFG_CMD_LOADB		\
-					 /* | CFG_CMD_IMI */		\
+					 | CFG_CMD_IMI			\
 					 /* | CFG_CMD_CACHE */		\
 					 | CFG_CMD_FLASH		\
 					 | CFG_CMD_MEMORY		\
-					 /* | CFG_CMD_NET */		\
+					 | CFG_CMD_NET			\
 					 | CFG_CMD_ENV			\
 					 /* | CFG_CMD_IRQ */		\
 					 | CFG_CMD_BOOTD		\
@@ -96,7 +130,7 @@
 					 /* | CFG_CMD_I2C */		\
 					 | CFG_CMD_REGINFO		\
 					 /* | CFG_CMD_DATE */		\
-					 /* | CFG_CMD_DHCP */		\
+					 | CFG_CMD_DHCP			\
 					 /* | CFG_CMD_AUTOSCRIPT */	\
 					 /* | CFG_CMD_MII */		\
 					 | CFG_CMD_MISC			\
@@ -106,19 +140,22 @@
 					 /* | CFG_CMD_SAVES */		\
 					 /* | CFG_CMD_SPI */		\
 					 /* | CFG_CMD_PING */		\
-					 /* | CFG_CMD_MMC */		\
-					 /* | CFG_CMD_FAT */		\
-					 /* | CFG_CMD_IMLS */		\
+					 | CFG_CMD_MMC			\
+					 | CFG_CMD_FAT			\
+					 | CFG_CMD_IMLS			\
 					 /* | CFG_CMD_ITEST */		\
-					 /* | CFG_CMD_EXT2 */		\
+					 | CFG_CMD_EXT2			\
+					 | CFG_CMD_JFFS2		\
 		)
 
 #include <cmd_confdefs.h>
 
 #define CONFIG_ATMEL_USART		1
+#define CONFIG_MACB			1
 #define CONFIG_PIO2			1
 #define CFG_NR_PIOS			5
 #define CFG_HSDRAMC			1
+#define CONFIG_MMC			1
 
 #define CFG_DCACHE_LINESZ		32
 #define CFG_ICACHE_LINESZ		32
@@ -150,16 +187,8 @@
 #define CFG_INIT_SP_ADDR		(CFG_INTRAM_BASE + CFG_INTRAM_SIZE)
 
 #define CFG_MALLOC_LEN			(256*1024)
-#define CFG_MALLOC_END							\
-	({								\
-		DECLARE_GLOBAL_DATA_PTR;				\
-		CFG_SDRAM_BASE + gd->sdram_size;			\
-	})
-#define CFG_MALLOC_START		(CFG_MALLOC_END - CFG_MALLOC_LEN)
-
 #define CFG_DMA_ALLOC_LEN		(16384)
-#define CFG_DMA_ALLOC_END		(CFG_MALLOC_START)
-#define CFG_DMA_ALLOC_START		(CFG_DMA_ALLOC_END - CFG_DMA_ALLOC_LEN)
+
 /* Allow 2MB for the kernel run-time image */
 #define CFG_LOAD_ADDR			(CFG_SDRAM_BASE + 0x00200000)
 #define CFG_BOOTPARAMS_LEN		(16 * 1024)
diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index 1606d0d..7f55366 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -78,7 +78,7 @@
 #define CONFIG_PCI_SYS_MEM_PHYS	CFG_SDRAM_BASE
 #define CONFIG_PCI_SYS_MEM_SIZE	(1024 * 1024 * 1024)
 
-#define CFG_ACE_BASE		0xe0000000	/* Xilinx ACE controller - Compact Flash */
+#define CFG_ACE_BASE		0xfe000000	/* Xilinx ACE controller - Compact Flash */
 
 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer (placed in internal SRAM)
diff --git a/include/configs/ml401.h b/include/configs/ml401.h
new file mode 100644
index 0000000..cb159e7
--- /dev/null
+++ b/include/configs/ml401.h
@@ -0,0 +1,230 @@
+/*
+ * (C) Copyright 2007 Czech Technical University.
+ *
+ * Michal SIMEK <monstr@seznam.cz>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "../board/xilinx/ml401/xparameters.h"
+
+#define	CONFIG_MICROBLAZE	1	/* MicroBlaze CPU */
+#define	CONFIG_ML401		1	/* ML401 Board */
+
+/* uart */
+#define	CONFIG_SERIAL_BASE	XILINX_UART_BASEADDR
+#define	CONFIG_BAUDRATE		XILINX_UART_BAUDRATE
+#define	CFG_BAUDRATE_TABLE	{ CONFIG_BAUDRATE }
+
+/* setting reset address */
+#define	CFG_RESET_ADDRESS	TEXT_BASE
+
+/* ethernet */
+#define CONFIG_EMACLITE		1
+#define XPAR_EMAC_0_DEVICE_ID	XPAR_XEMAC_NUM_INSTANCES
+
+/* gpio */
+#define	CFG_GPIO_0		1
+#define	CFG_GPIO_0_ADDR		XILINX_GPIO_BASEADDR
+
+/* interrupt controller */
+#define	CFG_INTC_0		1
+#define	CFG_INTC_0_ADDR		XILINX_INTC_BASEADDR
+#define	CFG_INTC_0_NUM		XILINX_INTC_NUM_INTR_INPUTS
+
+/* timer */
+#define	CFG_TIMER_0		1
+#define	CFG_TIMER_0_ADDR	XILINX_TIMER_BASEADDR
+#define	CFG_TIMER_0_IRQ		XILINX_TIMER_IRQ
+#define	FREQUENCE		XILINX_CLOCK_FREQ
+#define	CFG_TIMER_0_PRELOAD	( FREQUENCE/1000 )
+
+/*
+ * memory layout - Example
+ * TEXT_BASE = 0x1200_0000;
+ * CFG_SRAM_BASE = 0x1000_0000;
+ * CFG_SRAM_SIZE = 0x0400_0000;
+ *
+ * CFG_GBL_DATA_OFFSET = 0x1000_0000 + 0x0400_0000 - 0x1000 = 0x13FF_F000
+ * CFG_MONITOR_BASE = 0x13FF_F000 - 0x40000 = 0x13FB_F000
+ * CFG_MALLOC_BASE = 0x13FB_F000 - 0x40000 = 0x13F7_F000
+ *
+ * 0x1000_0000	CFG_SDRAM_BASE
+ *					FREE
+ * 0x1200_0000	TEXT_BASE
+ *		U-BOOT code
+ * 0x1202_0000
+ *					FREE
+ *
+ *					STACK
+ * 0x13F7_F000	CFG_MALLOC_BASE
+ *					MALLOC_AREA	256kB	Alloc
+ * 0x11FB_F000	CFG_MONITOR_BASE
+ *					MONITOR_CODE	256kB	Env
+ * 0x13FF_F000	CFG_GBL_DATA_OFFSET
+ * 					GLOBAL_DATA	4kB	bd, gd
+ * 0x1400_0000	CFG_SDRAM_BASE + CFG_SDRAM_SIZE
+ */
+
+/* ddr sdram - main memory */
+#define	CFG_SDRAM_BASE		XILINX_RAM_START
+#define	CFG_SDRAM_SIZE		XILINX_RAM_SIZE
+#define	CFG_MEMTEST_START	CFG_SDRAM_BASE
+#define	CFG_MEMTEST_END		(CFG_SDRAM_BASE + 0x1000)
+
+/* global pointer */
+#define	CFG_GBL_DATA_SIZE	0x1000	/* size of global data */
+#define	CFG_GBL_DATA_OFFSET     (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - CFG_GBL_DATA_SIZE) /* start of global data */
+
+/* monitor code */
+#define	SIZE			0x40000
+#define	CFG_MONITOR_LEN		SIZE
+#define	CFG_MONITOR_BASE	(CFG_GBL_DATA_OFFSET - CFG_MONITOR_LEN)
+#define	CFG_MONITOR_END		(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#define	CFG_MALLOC_LEN		SIZE
+#define	CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+
+/* stack */
+#define	CFG_INIT_SP_OFFSET	CFG_MONITOR_BASE
+
+/*#define	RAMENV */
+#define	FLASH
+
+#ifdef FLASH
+	#define	CFG_FLASH_BASE		XILINX_FLASH_START
+	#define	CFG_FLASH_SIZE		XILINX_FLASH_SIZE
+	#define	CFG_FLASH_CFI		1
+	#define	CFG_FLASH_CFI_DRIVER	1
+	#define	CFG_FLASH_EMPTY_INFO	1	/* ?empty sector */
+	#define	CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+	#define	CFG_MAX_FLASH_SECT	128	/* max number of sectors on one chip */
+
+	#ifdef	RAMENV
+		#define	CFG_ENV_IS_NOWHERE	1
+		#define	CFG_ENV_SIZE		0x1000
+		#define	CFG_ENV_ADDR		(CFG_MONITOR_BASE - CFG_ENV_SIZE)
+
+	#else	/* !RAMENV */
+		#define	CFG_ENV_IS_IN_FLASH	1
+		#define	CFG_ENV_ADDR		0x40000
+		#define	CFG_ENV_SECT_SIZE	0x40000	/* 256K(one sector) for env */
+		#define	CFG_ENV_SIZE		0x2000
+	#endif /* !RAMBOOT */
+#else /* !FLASH */
+	/* ENV in RAM */
+	#define	CFG_NO_FLASH		1
+	#define	CFG_ENV_IS_NOWHERE	1
+	#define	CFG_ENV_SIZE		0x1000
+	#define	CFG_ENV_ADDR		(CFG_MONITOR_BASE - CFG_ENV_SIZE)
+#endif /* !FLASH */
+
+#ifdef	FLASH
+	#ifdef	RAMENV
+	#define	CONFIG_COMMANDS	(CONFIG__CMD_DFL |\
+				CFG_CMD_MEMORY |\
+				CFG_CMD_MISC |\
+				CFG_CMD_AUTOSCRIPT |\
+				CFG_CMD_IRQ |\
+				CFG_CMD_ASKENV |\
+				CFG_CMD_BDI |\
+				CFG_CMD_RUN |\
+				CFG_CMD_LOADS |\
+				CFG_CMD_LOADB |\
+				CFG_CMD_IMI |\
+				CFG_CMD_NET |\
+				CFG_CMD_CACHE |\
+				CFG_CMD_IMLS |\
+				CFG_CMD_FLASH |\
+				CFG_CMD_PING \
+				)
+	#else	/* !RAMENV */
+	#define	CONFIG_COMMANDS	(CONFIG__CMD_DFL |\
+				CFG_CMD_MEMORY |\
+				CFG_CMD_MISC |\
+				CFG_CMD_AUTOSCRIPT |\
+				CFG_CMD_IRQ |\
+				CFG_CMD_ASKENV |\
+				CFG_CMD_BDI |\
+				CFG_CMD_RUN |\
+				CFG_CMD_LOADS |\
+				CFG_CMD_LOADB |\
+				CFG_CMD_IMI |\
+				CFG_CMD_NET |\
+				CFG_CMD_CACHE |\
+				CFG_CMD_IMLS |\
+				CFG_CMD_FLASH |\
+				CFG_CMD_PING |\
+				CFG_CMD_ENV |\
+				CFG_CMD_SAVES \
+				)
+
+	#endif
+
+#else	/* !FLASH */
+	#define	CONFIG_COMMANDS	(CONFIG__CMD_DFL |\
+				CFG_CMD_MEMORY |\
+				CFG_CMD_MISC |\
+				CFG_CMD_AUTOSCRIPT |\
+				CFG_CMD_IRQ |\
+				CFG_CMD_ASKENV |\
+				CFG_CMD_BDI |\
+				CFG_CMD_RUN |\
+				CFG_CMD_LOADS |\
+				CFG_CMD_LOADB |\
+				CFG_CMD_IMI |\
+				CFG_CMD_NET |\
+				CFG_CMD_CACHE |\
+				CFG_CMD_PING \
+				)
+#endif	/* !FLASH */
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/* Miscellaneous configurable options */
+#define	CFG_PROMPT	"U-Boot-mONStR> "
+#define	CFG_CBSIZE	512	/* size of console buffer */
+#define	CFG_PBSIZE	(CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* print buffer size */
+#define	CFG_MAXARGS	15	/* max number of command args */
+#define	CFG_LONGHELP
+#define	CFG_LOAD_ADDR	0x12000000 /* default load address */
+
+#define	CONFIG_BOOTDELAY 	30
+#define	CONFIG_BOOTARGS		"root=romfs"
+#define	CONFIG_HOSTNAME		"ml401"
+#define	CONFIG_BOOTCOMMAND 	"base 0;tftp 11000000 image.img;bootm"
+#define	CONFIG_IPADDR		192.168.0.3
+#define	CONFIG_SERVERIP 	192.168.0.5
+#define	CONFIG_GATEWAYIP 	192.168.0.1
+#define	CONFIG_ETHADDR		00:E0:0C:00:00:FD
+
+/* architecture dependent code */
+#define	CFG_USR_EXCEP	/* user exception */
+#define CFG_HZ	1000
+
+/* system ace */
+/*#define CONFIG_SYSTEMACE
+#define DEBUG_SYSTEMACE
+#define CFG_SYSTEMACE_BASE	XILINX_SYSACE_BASEADDR
+#define CFG_SYSTEMACE_WIDTH	XILINX_SYSACE_MEM_WIDTH
+#define CONFIG_DOS_PARTITION
+*/
+#endif	/* __CONFIG_H */
diff --git a/include/configs/mpc7448hpc2.h b/include/configs/mpc7448hpc2.h
new file mode 100644
index 0000000..243a3f6
--- /dev/null
+++ b/include/configs/mpc7448hpc2.h
@@ -0,0 +1,411 @@
+/*
+ * Copyright (c) 2005 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2006
+ * Alex Bounine , Tundra Semiconductor Corp.
+ * Roy Zang	, <tie-fei.zang@freescale.com> Freescale Corp.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board specific configuration options for Freescale
+ * MPC7448HPC2 (High-Performance Computing II) (Taiga) board
+ *
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef DEBUG
+
+/* Board Configuration Definitions */
+/* MPC7448HPC2 (High-Performance Computing II) (Taiga) board */
+
+#define CONFIG_MPC7448HPC2
+
+#define CONFIG_74xx
+#define CONFIG_750FX		/* this option to enable init of extended BATs */
+#define CONFIG_ALTIVEC		/* undef to disable */
+
+#define CFG_BOARD_NAME		"MPC7448 HPC II"
+#define CONFIG_IDENT_STRING	" Freescale MPC7448 HPC II"
+
+#define CFG_OCN_CLK		133000000	/* 133 MHz */
+#define CFG_CONFIG_BUS_CLK	133000000
+
+#define CFG_CLK_SPREAD		/* Enable Spread-Spectrum Clock generation */
+
+#undef  CONFIG_ECC		/* disable ECC support */
+
+/* Board-specific Initialization Functions to be called */
+#define CFG_BOARD_ASM_INIT
+#define CONFIG_BOARD_EARLY_INIT_F
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HAS_ETH1
+
+#define CONFIG_ENV_OVERWRITE
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_BAUDRATE		115200	/* console baudrate = 115000 */
+
+/*#define CFG_HUSH_PARSER */
+#undef CFG_HUSH_PARSER
+
+#define CFG_PROMPT_HUSH_PS2	"> "
+
+/* Pass open firmware flat tree */
+#define CONFIG_OF_FLAT_TREE	1
+#define CONFIG_OF_BOARD_SETUP	1
+
+/* maximum size of the flat tree (8K) */
+#define OF_FLAT_TREE_MAX_SIZE	8192
+
+#define OF_CPU			"PowerPC,7448@0"
+#define OF_TSI			"tsi108@c0000000"
+#define OF_TBCLK		(bd->bi_busfreq / 8)
+#define OF_STDOUT_PATH		"/tsi108@c0000000/serial@7808"
+
+/*
+ * The following defines let you select what serial you want to use
+ * for your console driver.
+ *
+ * what to do:
+ * If you have hacked a serial cable onto the second DUART channel,
+ * change the CFG_DUART port from 1 to 0 below.
+ *
+ */
+
+#define CONFIG_CONS_INDEX	1
+#define CFG_NS16550
+#define CFG_NS16550_SERIAL
+#define CFG_NS16550_REG_SIZE	1
+#define CFG_NS16550_CLK		CFG_OCN_CLK * 8
+
+#define CFG_NS16550_COM1	(CFG_TSI108_CSR_RST_BASE+0x7808)
+#define CFG_NS16550_COM2	(CFG_TSI108_CSR_RST_BASE+0x7C08)
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds */
+#define CONFIG_ZERO_BOOTDELAY_CHECK
+
+#undef CONFIG_BOOTARGS
+/* #define CONFIG_PREBOOT  "echo;echo Type \"run flash_nfs\"
+ * to mount root filesystem over NFS;echo" */
+
+#if (CONFIG_BOOTDELAY >= 0)
+#define CONFIG_BOOTCOMMAND	"tftpboot 0x400000 zImage.initrd.elf;\
+ setenv bootargs $(bootargs) $(bootargs_root) nfsroot=$(serverip):$(rootpath) \
+ ip=$(ipaddr):$(serverip)$(bootargs_end);  bootm 0x400000; "
+
+#define CONFIG_BOOTARGS "console=ttyS0,115200"
+#endif
+
+#undef CONFIG_EXTRA_ENV_SETTINGS
+
+#define CONFIG_SERIAL	"No. 1"
+
+/* Networking Configuration */
+
+#define KSEG1ADDR(a)	(a)	/* Needed by the rtl8139 driver */
+
+#define CONFIG_TSI108_ETH
+#define CONFIG_TSI108_ETH_NUM_PORTS	2
+
+#define CONFIG_NET_MULTI
+
+#define CONFIG_BOOTFILE		zImage.initrd.elf
+#define CONFIG_LOADADDR		0x400000
+
+/*-------------------------------------------------------------------------- */
+
+#define CONFIG_LOADS_ECHO	0	/* echo off for serial download */
+#define CFG_LOADS_BAUD_CHANGE	/* allow baudrate changes */
+
+#undef CONFIG_WATCHDOG		/* watchdog disabled */
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | \
+				CONFIG_BOOTP_BOOTFILESIZE)
+
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL \
+		| CFG_CMD_ASKENV \
+		| CFG_CMD_CACHE \
+		| CFG_CMD_PCI \
+		| CFG_CMD_I2C \
+		| CFG_CMD_SDRAM \
+		| CFG_CMD_EEPROM \
+		| CFG_CMD_FLASH \
+		| CFG_CMD_ENV \
+		| CFG_CMD_BSP \
+		| CFG_CMD_DHCP \
+		| CFG_CMD_PING \
+		| CFG_CMD_DATE)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*set date in u-boot*/
+#define CONFIG_RTC_M48T35A
+#define CFG_NVRAM_BASE_ADDR	0xfc000000
+#define CFG_NVRAM_SIZE		0x8000
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_VERSION_VARIABLE		1
+#define CONFIG_TSI108_I2C
+
+#define CFG_I2C_EEPROM_ADDR		0x50	/* I2C EEPROM page 1 */
+#define CFG_I2C_EEPROM_ADDR_LEN		1	/* Bytes of address */
+
+#define CFG_LONGHELP		/* undef to save memory */
+#define CFG_PROMPT	"=> "	/* Monitor Command Prompt */
+
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size */
+#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port at */
+#else
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size */
+#endif
+
+#define CFG_PBSIZE (CFG_CBSIZE + sizeof(CFG_PROMPT) + 16)/* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args */
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START	0x00400000	/* memtest works on */
+#define CFG_MEMTEST_END		0x07c00000	/* 4 ... 124 MB in DRAM */
+
+#define CFG_LOAD_ADDR	0x00400000	/* default load address */
+
+#define CFG_HZ		1000		/* decr freq: 1ms ticks */
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area
+ */
+
+/*
+ * When locking data in cache you should point the CFG_INIT_RAM_ADDRESS
+ * To an unused memory region. The stack will remain in cache until RAM
+ * is initialized
+ */
+#undef  CFG_INIT_RAM_LOCK
+#define CFG_INIT_RAM_ADDR	0x07d00000	/* unused memory region */
+#define CFG_INIT_RAM_END	0x4000/* larger space - we have SDRAM initialized */
+
+#define CFG_GBL_DATA_SIZE	128/* size in bytes reserved for init data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+
+#define CFG_SDRAM_BASE		0x00000000	/* first 256 MB of SDRAM */
+#define CFG_SDRAM1_BASE		0x10000000	/* next 256MB of SDRAM */
+
+#define CFG_SDRAM2_BASE	0x40000000	/* beginning of non-cacheable alias for SDRAM - first 256MB */
+#define CFG_SDRAM3_BASE	0x50000000	/* next Non-Cacheable 256MB of SDRAM */
+
+#define CFG_PCI_PFM_BASE	0x80000000	/* Prefetchable (cacheable) PCI/X PFM and SDRAM OCN (128MB+128MB) */
+
+#define CFG_PCI_MEM32_BASE	0xE0000000	/* Non-Cacheable PCI/X MEM and SDRAM OCN (128MB+128MB) */
+
+#define CFG_MISC_REGION_BASE	0xf0000000	/* Base Address for (PCI/X + Flash) region */
+
+#define CFG_FLASH_BASE	0xff000000	/* Base Address of Flash device */
+#define CFG_FLASH_BASE2	0xfe000000	/* Alternate Flash Base Address */
+
+#define CONFIG_VERY_BIG_RAM	/* we will use up to 256M memory for cause we are short of BATS */
+
+#define PCI0_IO_BASE_BOOTM	0xfd000000
+
+#define CFG_RESET_ADDRESS	0x3fffff00
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+#define CFG_MONITOR_BASE	TEXT_BASE	/* u-boot code base */
+#define CFG_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc */
+
+/* Peripheral Device section */
+
+/*
+ * Resources on the Tsi108
+ */
+
+#define CFG_TSI108_CSR_RST_BASE	0xC0000000	/* Tsi108 CSR base after reset */
+#define CFG_TSI108_CSR_BASE	CFG_TSI108_CSR_RST_BASE	/* Runtime Tsi108 CSR base */
+
+#define ENABLE_PCI_CSR_BAR	/* enables access to Tsi108 CSRs from the PCI/X bus */
+
+#undef  DISABLE_PBM
+
+/*
+ * PCI stuff
+ *
+ */
+
+#define CONFIG_PCI		/* include pci support */
+#define CONFIG_TSI108_PCI	/* include tsi108 pci support */
+
+#define PCI_HOST_ADAPTER	0	/* configure as pci adapter */
+#define PCI_HOST_FORCE		1	/* configure as pci host */
+#define PCI_HOST_AUTO		2	/* detected via arbiter enable */
+
+#define CONFIG_PCI_HOST PCI_HOST_FORCE	/* select pci host function */
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+
+/* PCI MEMORY MAP section */
+
+/* PCI view of System Memory */
+#define CFG_PCI_MEMORY_BUS	0x00000000
+#define CFG_PCI_MEMORY_PHYS	0x00000000
+#define CFG_PCI_MEMORY_SIZE	0x80000000
+
+/* PCI Memory Space */
+#define CFG_PCI_MEM_BUS		(CFG_PCI_MEM_PHYS)
+#define CFG_PCI_MEM_PHYS	(CFG_PCI_MEM32_BASE)	/* 0xE0000000 */
+#define CFG_PCI_MEM_SIZE	0x10000000	/* 256 MB space for PCI/X Mem + SDRAM OCN */
+
+/* PCI I/O Space */
+#define CFG_PCI_IO_BUS		0x00000000
+#define CFG_PCI_IO_PHYS		0xfa000000	/* Changed from fd000000 */
+
+#define CFG_PCI_IO_SIZE		0x01000000	/* 16MB */
+
+#define _IO_BASE		0x00000000	/* points to PCI I/O space      */
+
+/* PCI Config Space mapping */
+#define CFG_PCI_CFG_BASE	0xfb000000	/* Changed from FE000000 */
+#define CFG_PCI_CFG_SIZE	0x01000000	/* 16MB */
+
+#define CFG_IBAT0U	0xFE0003FF
+#define CFG_IBAT0L	0xFE000002
+
+#define CFG_IBAT1U	0x00007FFF
+#define CFG_IBAT1L	0x00000012
+
+#define CFG_IBAT2U	0x80007FFF
+#define CFG_IBAT2L	0x80000022
+
+#define CFG_IBAT3U	0x00000000
+#define CFG_IBAT3L	0x00000000
+
+#define CFG_IBAT4U	0x00000000
+#define CFG_IBAT4L	0x00000000
+
+#define CFG_IBAT5U	0x00000000
+#define CFG_IBAT5L	0x00000000
+
+#define CFG_IBAT6U	0x00000000
+#define CFG_IBAT6L	0x00000000
+
+#define CFG_IBAT7U	0x00000000
+#define CFG_IBAT7L	0x00000000
+
+#define CFG_DBAT0U	0xE0003FFF
+#define CFG_DBAT0L	0xE000002A
+
+#define CFG_DBAT1U	0x00007FFF
+#define CFG_DBAT1L	0x00000012
+
+#define CFG_DBAT2U	0x00000000
+#define CFG_DBAT2L	0x00000000
+
+#define CFG_DBAT3U	0xC0000003
+#define CFG_DBAT3L	0xC000002A
+
+#define CFG_DBAT4U	0x00000000
+#define CFG_DBAT4L	0x00000000
+
+#define CFG_DBAT5U	0x00000000
+#define CFG_DBAT5L	0x00000000
+
+#define CFG_DBAT6U	0x00000000
+#define CFG_DBAT6L	0x00000000
+
+#define CFG_DBAT7U	0x00000000
+#define CFG_DBAT7L	0x00000000
+
+/* I2C addresses for the two DIMM SPD chips */
+#define DIMM0_I2C_ADDR	0x51
+#define DIMM1_I2C_ADDR	0x52
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	(8<<20)	/* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1/* Flash can be at one of two addresses */
+#define FLASH_BANK_SIZE		0x01000000	/* 16 MB Total */
+#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
+
+#define CFG_FLASH_CFI_DRIVER
+#define CFG_FLASH_CFI
+#define CFG_WRITE_SWAPPED_DATA
+
+#define PHYS_FLASH_SIZE		0x01000000
+#define CFG_MAX_FLASH_SECT	(128)
+
+#define CFG_ENV_IS_IN_NVRAM
+#define CFG_ENV_ADDR		0xFC000000
+
+#define CFG_ENV_OFFSET	0x00000000	/* Offset of Environment Sector */
+#define CFG_ENV_SIZE	0x00000400	/* Total Size of Environment Space */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	32	/* For all MPC74xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * L2CR setup -- make sure this is right for your board!
+ * look in include/mpc74xx.h for the defines used here
+ */
+#undef CFG_L2
+
+#define L2_INIT		0
+#define L2_ENABLE	(L2_INIT | L2CR_L2E)
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM	0x02	/* Software reboot */
+#define CFG_SERIAL_HANG_IN_EXCEPTION
+#endif	/* __CONFIG_H */
diff --git a/include/configs/sc3.h b/include/configs/sc3.h
index 8298084..6b6acfa 100644
--- a/include/configs/sc3.h
+++ b/include/configs/sc3.h
@@ -133,8 +133,8 @@
 
 #if 1	/* feel free to disable for development */
 #define CONFIG_AUTOBOOT_KEYED		/* Enable password protection	*/
-#define CONFIG_AUTOBOOT_PROMPT		"\nSC3 - booting... stop with S\n"
-#define CONFIG_AUTOBOOT_DELAY_STR	"S"	/* 1st "password"	*/
+#define CONFIG_AUTOBOOT_PROMPT		"\nSC3 - booting... stop with ENTER\n"
+#define CONFIG_AUTOBOOT_DELAY_STR	"\n"	/* 1st "password"	*/
 #endif
 
 /*
@@ -416,11 +416,11 @@ extern unsigned long offsetOfEnvironment;
 
 #define CONFIG_JFFS2_NAND 1			/* jffs2 on nand support */
 
-/* No command line, one static partition Partition 3 contains jffs2 rootfs */
+/* No command line, one static partition */
 #undef	CONFIG_JFFS2_CMDLINE
 #define CONFIG_JFFS2_DEV		"nand0"
-#define CONFIG_JFFS2_PART_SIZE		0x00400000
-#define CONFIG_JFFS2_PART_OFFSET	0x00c00000
+#define CONFIG_JFFS2_PART_SIZE		0x01000000
+#define CONFIG_JFFS2_PART_OFFSET	0x00000000
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 29f3b40..1f19621 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -33,7 +33,6 @@
  *----------------------------------------------------------------------*/
 /* This config file is used for Sequoia (440EPx) and Rainier (440GRx)	*/
 #ifndef CONFIG_RAINIER
-#define CONFIG_SEQUOIA		1		/* Board is Sequoia	*/
 #define CONFIG_440EPX		1		/* Specific PPC440EPx	*/
 #else
 #define CONFIG_440GRX		1		/* Specific PPC440GRx	*/
@@ -75,9 +74,7 @@
  * Initial RAM & stack pointer
  *----------------------------------------------------------------------*/
 /* 440EPx/440GRx have 16KB of internal SRAM, so no need for D-Cache	*/
-#define CFG_INIT_RAM_OCM	1		/* OCM as init ram	*/
 #define CFG_INIT_RAM_ADDR	CFG_OCM_BASE	/* OCM			*/
-
 #define CFG_INIT_RAM_END	(4 << 10)
 #define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
@@ -381,9 +378,6 @@
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
-#define CFG_FLASH		CFG_FLASH_BASE
-#define CFG_NAND		0xD0000000
-#define CFG_CPLD		0xC0000000
 
 /*
  * On Sequoia CS0 and CS3 are switched when configuring for NAND booting
@@ -392,25 +386,25 @@
 #define CFG_NAND_CS		3		/* NAND chip connected to CSx	*/
 /* Memory Bank 0 (NOR-FLASH) initialization					*/
 #define CFG_EBC_PB0AP		0x03017200
-#define CFG_EBC_PB0CR		(CFG_FLASH | 0xda000)
+#define CFG_EBC_PB0CR		(CFG_FLASH_BASE | 0xda000)
 
 /* Memory Bank 3 (NAND-FLASH) initialization					*/
 #define CFG_EBC_PB3AP		0x018003c0
-#define CFG_EBC_PB3CR		(CFG_NAND | 0x1c000)
+#define CFG_EBC_PB3CR		(CFG_NAND_ADDR | 0x1c000)
 #else
 #define CFG_NAND_CS		0		/* NAND chip connected to CSx	*/
 /* Memory Bank 3 (NOR-FLASH) initialization					*/
 #define CFG_EBC_PB3AP		0x03017200
-#define CFG_EBC_PB3CR		(CFG_FLASH | 0xda000)
+#define CFG_EBC_PB3CR		(CFG_FLASH_BASE | 0xda000)
 
 /* Memory Bank 0 (NAND-FLASH) initialization					*/
 #define CFG_EBC_PB0AP		0x018003c0
-#define CFG_EBC_PB0CR		(CFG_NAND | 0x1c000)
+#define CFG_EBC_PB0CR		(CFG_NAND_ADDR | 0x1c000)
 #endif
 
 /* Memory Bank 2 (CPLD) initialization						*/
 #define CFG_EBC_PB2AP		0x24814580
-#define CFG_EBC_PB2CR		(CFG_CPLD | 0x38000)
+#define CFG_EBC_PB2CR		(CFG_BCSR_BASE | 0x38000)
 
 /*-----------------------------------------------------------------------
  * NAND FLASH
diff --git a/include/configs/suzaku.h b/include/configs/suzaku.h
index 1ee6be1..8224555 100644
--- a/include/configs/suzaku.h
+++ b/include/configs/suzaku.h
@@ -44,12 +44,17 @@
 #define CFG_FLASH_SIZE		0x00400000
 #define CFG_RESET_ADDRESS	0xfff00100
 #define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
-#define CFG_MONITOR_BASE        (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - (1024 * 1024))
+#define CFG_MONITOR_BASE	(CFG_SDRAM_BASE + CFG_SDRAM_SIZE - (1024 * 1024))
 #define CFG_MALLOC_LEN		(256 << 10)	/* Reserve 256 kB for malloc */
+#define CFG_MALLOC_BASE		(CFG_MONITOR_BASE - (1024 * 1024))
 
 #define CONFIG_BAUDRATE		115200
 #define CFG_BAUDRATE_TABLE	{ 115200 }
 
+/* System Register (GPIO) */
+#define MICROBLAZE_SYSREG_BASE_ADDR 0xFFFFA000
+#define MICROBLAZE_SYSREG_RECONFIGURE (1 << 0)
+
 #define CONFIG_COMMANDS		(CONFIG__CMD_DFL)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
diff --git a/include/configs/xupv2p.h b/include/configs/xupv2p.h
new file mode 100644
index 0000000..a2f4810
--- /dev/null
+++ b/include/configs/xupv2p.h
@@ -0,0 +1,174 @@
+/*
+ * (C) Copyright 2007 Czech Technical University.
+ *
+ * Michal SIMEK <monstr@monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#include "../board/xilinx/xupv2p/xparameters.h"
+
+#define	CONFIG_MICROBLAZE	1	/* MicroBlaze CPU */
+#define	CONFIG_XUPV2P		1
+
+/* uart */
+#define	CONFIG_SERIAL_BASE	XILINX_UART_BASEADDR
+#define	CONFIG_BAUDRATE		XILINX_UART_BAUDRATE
+#define	CFG_BAUDRATE_TABLE	{ CONFIG_BAUDRATE }
+
+/* ethernet */
+#define CONFIG_EMAC	1
+#define XPAR_EMAC_0_DEVICE_ID	XPAR_XEMAC_NUM_INSTANCES
+
+/*
+ * setting reset address
+ *
+ * TEXT_BASE is set to place, where the U-BOOT run in RAM, but
+ * if you want to store U-BOOT in flash, set CFG_RESET_ADDRESS
+ * to FLASH memory and after loading bitstream jump to FLASH.
+ * U-BOOT auto-relocate to TEXT_BASE. After RESET command Microblaze
+ * jump to CFG_RESET_ADDRESS where is the original U-BOOT code.
+ */
+#define	CFG_RESET_ADDRESS	0x36000000
+
+/* gpio */
+#define	CFG_GPIO_0		1
+#define	CFG_GPIO_0_ADDR		XILINX_GPIO_BASEADDR
+
+/* interrupt controller */
+#define	CFG_INTC_0		1
+#define	CFG_INTC_0_ADDR		XILINX_INTC_BASEADDR
+#define	CFG_INTC_0_NUM		XILINX_INTC_NUM_INTR_INPUTS
+
+/* timer */
+#define	CFG_TIMER_0		1
+#define	CFG_TIMER_0_ADDR	XILINX_TIMER_BASEADDR
+#define	CFG_TIMER_0_IRQ		XILINX_TIMER_IRQ
+#define	FREQUENCE		XILINX_CLOCK_FREQ
+#define	CFG_TIMER_0_PRELOAD	( FREQUENCE/1000 )
+
+/*
+ * memory layout - Example
+ * TEXT_BASE = 0x3600_0000;
+ * CFG_SRAM_BASE = 0x3000_0000;
+ * CFG_SRAM_SIZE = 0x1000_0000;
+ *
+ * CFG_GBL_DATA_OFFSET = 0x3000_0000 + 0x1000_0000 - 0x1000 = 0x3FFF_F000
+ * CFG_MONITOR_BASE = 0x3FFF_F000 - 0x40000 = 0x3FFB_F000
+ * CFG_MALLOC_BASE = 0x3FFB_F000 - 0x40000 = 0x3FF7_F000
+ *
+ * 0x3000_0000	CFG_SDRAM_BASE
+ *					FREE
+ * 0x3600_0000	TEXT_BASE
+ *		U-BOOT code
+ * 0x3602_0000
+ *					FREE
+ *
+ *					STACK
+ * 0x3FF7_F000	CFG_MALLOC_BASE
+ *					MALLOC_AREA	256kB	Alloc
+ * 0x3FFB_F000	CFG_MONITOR_BASE
+ *					MONITOR_CODE	256kB	Env
+ * 0x3FFF_F000	CFG_GBL_DATA_OFFSET
+ * 					GLOBAL_DATA	4kB	bd, gd
+ * 0x4000_0000	CFG_SDRAM_BASE + CFG_SDRAM_SIZE
+ */
+
+/* ddr sdram - main memory */
+#define	CFG_SDRAM_BASE		XILINX_RAM_START
+#define	CFG_SDRAM_SIZE		XILINX_RAM_SIZE
+#define	CFG_MEMTEST_START	CFG_SDRAM_BASE
+#define	CFG_MEMTEST_END		(CFG_SDRAM_BASE + 0x1000)
+
+/* global pointer */
+#define	CFG_GBL_DATA_SIZE	0x1000	/* size of global data */
+#define	CFG_GBL_DATA_OFFSET     (CFG_SDRAM_BASE + CFG_SDRAM_SIZE - CFG_GBL_DATA_SIZE) /* start of global data */
+
+/* monitor code */
+#define	SIZE			0x40000
+#define	CFG_MONITOR_LEN		SIZE
+#define	CFG_MONITOR_BASE	(CFG_GBL_DATA_OFFSET - CFG_MONITOR_LEN)
+#define	CFG_MONITOR_END		(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+#define	CFG_MALLOC_LEN		SIZE
+#define	CFG_MALLOC_BASE		(CFG_MONITOR_BASE - CFG_MALLOC_LEN)
+
+/* stack */
+#define	CFG_INIT_SP_OFFSET	CFG_MALLOC_BASE
+
+#define	CFG_NO_FLASH		1
+#define	CFG_ENV_IS_NOWHERE	1
+#define	CFG_ENV_SIZE		0x1000
+#define	CFG_ENV_ADDR		(CFG_MONITOR_BASE - CFG_ENV_SIZE)
+#define	CONFIG_COMMANDS	(CONFIG__CMD_DFL |\
+			CFG_CMD_MEMORY |\
+			CFG_CMD_IRQ |\
+			CFG_CMD_BDI |\
+			CFG_CMD_NET |\
+			CFG_CMD_IMI |\
+			CFG_CMD_ECHO |\
+			CFG_CMD_CACHE |\
+			CFG_CMD_RUN |\
+			CFG_CMD_AUTOSCRIPT |\
+			CFG_CMD_ASKENV |\
+			CFG_CMD_LOADS |\
+			CFG_CMD_LOADB |\
+			CFG_CMD_MISC |\
+			CFG_CMD_PING \
+			)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/* Miscellaneous configurable options */
+#define	CFG_PROMPT	"U-Boot-mONStR> "
+#define	CFG_CBSIZE	512	/* size of console buffer */
+#define	CFG_PBSIZE	(CFG_CBSIZE + sizeof(CFG_PROMPT) + 16) /* print buffer size */
+#define	CFG_MAXARGS	15	/* max number of command args */
+#define	CFG_LONGHELP
+#define	CFG_LOAD_ADDR	0x12000000 /* default load address */
+
+#define	CONFIG_BOOTDELAY 	30
+#define	CONFIG_BOOTARGS		"root=romfs"
+#define	CONFIG_HOSTNAME		"ml401"
+#define	CONFIG_BOOTCOMMAND 	"base 0;tftp 11000000 image.img;bootm"
+#define	CONFIG_IPADDR		192.168.0.3
+#define	CONFIG_SERVERIP 	192.168.0.5
+#define	CONFIG_GATEWAYIP 	192.168.0.1
+#define	CONFIG_ETHADDR		00:E0:0C:00:00:FD
+
+/* architecture dependent code */
+#define	CFG_USR_EXCEP	/* user exception */
+#define CFG_HZ	1000
+
+#define CONFIG_PREBOOT	"echo U-BOOT by mONStR;"	\
+	"base 0;" \
+	"echo"
+
+
+/* system ace */
+/*#define	CONFIG_SYSTEMACE
+#define	DEBUG_SYSTEMACE
+#define	CFG_SYSTEMACE_BASE	0xCF000000
+#define	CFG_SYSTEMACE_WIDTH	16
+#define	CONFIG_DOS_PARTITION*/
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index b59f75b..0a41dff 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -32,7 +32,6 @@
  *----------------------------------------------------------------------*/
 /* This config file is used for Yosemite (440EP) and Yellowstone (440GR)*/
 #ifndef CONFIG_YELLOWSTONE
-#define CONFIG_YOSEMITE		1	/* Board is Yosemite		*/
 #define CONFIG_440EP		1	/* Specific PPC440EP support	*/
 #define CONFIG_HOSTNAME		yosemite
 #else
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index eb4859c..7f8b022 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -120,7 +120,7 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_SPD_EEPROM	1	/* Use SPD EEPROM for setup	*/
 #define SPD_EEPROM_ADDRESS	{0x53, 0x52}	/* SPD i2c spd addresses*/
-#undef CONFIG_DDR_ECC			/* no ECC support for now	*/
+#define CONFIG_DDR_ECC		1	/* with ECC support		*/
 
 /*-----------------------------------------------------------------------
  * I2C