Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts: arch/arm/cpu/armv7/rmobile/Makefile doc/README.scrapyard Needed manual fix: arch/arm/cpu/armv7/omap-common/Makefile board/compulab/cm_t335/u-boot.lds
author: Albert ARIBAUD <albert.u.boot@aribaud.net> 2013-12-10 14:31:56 +0100
committer: Albert ARIBAUD <albert.u.boot@aribaud.net> 2013-12-10 22:23:59 +0100
commit: f15ea6e1d67782a1626d4a4922b6c20e380085e5 (patch)
tree: 57d78f1ee94a2060eaa591533278d2934d4f1da3 /include/configs
parent: cb7ee1b98cac6baf244daefb1192adf5a47bc983 (diff)
parent: f44483b57c49282299da0e5c10073b909cdad979 (diff)
download: u-boot-imx-f15ea6e1d67782a1626d4a4922b6c20e380085e5.zip
u-boot-imx-f15ea6e1d67782a1626d4a4922b6c20e380085e5.tar.gz
u-boot-imx-f15ea6e1d67782a1626d4a4922b6c20e380085e5.tar.bz2
98 files changed, 2455 insertions, 1011 deletions
diff --git a/include/configs/ASH405.h b/include/configs/ASH405.h
index 9460be3..2f53407 100644
--- a/include/configs/ASH405.h
+++ b/include/configs/ASH405.h
@@ -143,6 +143,8 @@
 
 #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I	1	/* ".i" read skips bad blocks   */
 #define CONFIG_SYS_NAND_QUIET		1
+#define CONFIG_SYS_NAND_MAX_OOBFREE	2
+#define CONFIG_SYS_NAND_MAX_ECCPOS	56
 
 /*-----------------------------------------------------------------------
  * PCI stuff
diff --git a/include/configs/B4860QDS.h b/include/configs/B4860QDS.h
index 268f66e..b2a5c19 100644
--- a/include/configs/B4860QDS.h
+++ b/include/configs/B4860QDS.h
@@ -193,7 +193,7 @@ unsigned long get_board_ddr_clk(void);
 
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_DDR_RAW_TIMING
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_FSL_DDR_INTERACTIVE
 
 #define CONFIG_SYS_SPD_BUS_NUM	0
diff --git a/include/configs/BSC9131RDB.h b/include/configs/BSC9131RDB.h
index 036f264..499d8c2 100644
--- a/include/configs/BSC9131RDB.h
+++ b/include/configs/BSC9131RDB.h
@@ -80,7 +80,7 @@
 #define CONFIG_SYS_MEMTEST_END		0x01ffffff
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #undef CONFIG_SYS_DDR_RAW_TIMING
 #undef CONFIG_DDR_SPD
 #define CONFIG_SYS_SPD_BUS_NUM		0
diff --git a/include/configs/BSC9132QDS.h b/include/configs/BSC9132QDS.h
index 75889b3..a6601fe 100644
--- a/include/configs/BSC9132QDS.h
+++ b/include/configs/BSC9132QDS.h
@@ -134,7 +134,7 @@
 #define CONFIG_SYS_MEMTEST_END		0x01ffffff
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_SYS_SPD_BUS_NUM		0
 #define SPD_EEPROM_ADDRESS1		0x54 /* I2C access */
 #define SPD_EEPROM_ADDRESS2		0x56 /* I2C access */
diff --git a/include/configs/C29XPCIE.h b/include/configs/C29XPCIE.h
index 08156c5..1cfb2c2 100644
--- a/include/configs/C29XPCIE.h
+++ b/include/configs/C29XPCIE.h
@@ -103,7 +103,7 @@
 #define CONFIG_PANIC_HANG
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_SPD_BUS_NUM		0
 #define SPD_EEPROM_ADDRESS		0x50
@@ -191,13 +191,14 @@
 				| CSPR_MSEL_NAND \
 				| CSPR_V)
 #define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+#define CONFIG_SYS_NAND_OOBSIZE	0x00000280	/* 640b */
 #define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
 				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
 				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */ \
-				| CSOR_NAND_RAL_2	/* RAL = 2 Bytes */ \
-				| CSOR_NAND_PGS_2K	/* Page Size = 2k */ \
-				| CSOR_NAND_SPRZ_64	/* Spare size = 64 */ \
-				| CSOR_NAND_PB(64))	/* 64 Pages Per Block */
+				| CSOR_NAND_RAL_3	/* RAL = 3 Bytes */ \
+				| CSOR_NAND_PGS_8K	/* Page Size = 8K */ \
+				| CSOR_NAND_SPRZ_CSOR_EXT /*oob in csor_ext*/\
+				| CSOR_NAND_PB(128))	/*128 Pages Per Block*/
 #define CONFIG_SYS_NAND_FTIM0	(FTIM0_NAND_TCCST(0x01) | \
 				FTIM0_NAND_TWP(0x0c)   | \
 				FTIM0_NAND_TWCHT(0x08) | \
@@ -224,6 +225,7 @@
 #define CONFIG_SYS_CSPR1		CONFIG_SYS_NAND_CSPR
 #define CONFIG_SYS_AMASK1		CONFIG_SYS_NAND_AMASK
 #define CONFIG_SYS_CSOR1		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CSOR1_EXT		CONFIG_SYS_NAND_OOBSIZE
 #define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NAND_FTIM0
 #define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NAND_FTIM1
 #define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NAND_FTIM2
diff --git a/include/configs/HWW1U1A.h b/include/configs/HWW1U1A.h
index f3f2136..bbfee7d 100644
--- a/include/configs/HWW1U1A.h
+++ b/include/configs/HWW1U1A.h
@@ -255,7 +255,7 @@
 /* -------------------------------------------------------------------- */
 
 /* FreeScale DDR2/3 SDRAM Controller */
-#define CONFIG_FSL_DDR2		/* Our SDRAM slot is DDR2		*/
+#define CONFIG_SYS_FSL_DDR2		/* Our SDRAM slot is DDR2		*/
 #define CONFIG_DDR_ECC		/* Enable ECC by default		*/
 #define CONFIG_DDR_SPD		/* Detect DDR config from SPD EEPROM	*/
 #define CONFIG_SPD_EEPROM	/* ...why 2 config variables for this?	*/
diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index 3f742a2..a80a696 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -62,11 +62,11 @@
 #define CONFIG_SPD_EEPROM		/* use SPD EEPROM for DDR setup*/
 
 /*
- * define CONFIG_FSL_DDR2 to use unified DDR driver
+ * define CONFIG_SYS_FSL_DDR2 to use unified DDR driver
  * undefine it to use old spd_sdram.c
  */
-#define CONFIG_FSL_DDR2
-#ifdef CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
+#ifdef CONFIG_SYS_FSL_DDR2
 #define CONFIG_SYS_SPD_BUS_NUM	0
 #define SPD_EEPROM_ADDRESS1	0x52
 #define SPD_EEPROM_ADDRESS2	0x51
diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h
index 8197f89..9ab1bc1 100644
--- a/include/configs/MPC8536DS.h
+++ b/include/configs/MPC8536DS.h
@@ -122,7 +122,7 @@
 
 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
diff --git a/include/configs/MPC8540ADS.h b/include/configs/MPC8540ADS.h
index 6689368..046b14b 100644
--- a/include/configs/MPC8540ADS.h
+++ b/include/configs/MPC8540ADS.h
@@ -78,7 +78,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
diff --git a/include/configs/MPC8541CDS.h b/include/configs/MPC8541CDS.h
index e24c597..eca3b53 100644
--- a/include/configs/MPC8541CDS.h
+++ b/include/configs/MPC8541CDS.h
@@ -51,7 +51,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
diff --git a/include/configs/MPC8544DS.h b/include/configs/MPC8544DS.h
index 2e76df6..8132ec0 100644
--- a/include/configs/MPC8544DS.h
+++ b/include/configs/MPC8544DS.h
@@ -63,7 +63,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
diff --git a/include/configs/MPC8548CDS.h b/include/configs/MPC8548CDS.h
index 9ff048a..6acd54d 100644
--- a/include/configs/MPC8548CDS.h
+++ b/include/configs/MPC8548CDS.h
@@ -75,7 +75,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
diff --git a/include/configs/MPC8555CDS.h b/include/configs/MPC8555CDS.h
index 7f0f927..5ffdd01 100644
--- a/include/configs/MPC8555CDS.h
+++ b/include/configs/MPC8555CDS.h
@@ -51,7 +51,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
diff --git a/include/configs/MPC8560ADS.h b/include/configs/MPC8560ADS.h
index b7c4a60..bb9ae2d 100644
--- a/include/configs/MPC8560ADS.h
+++ b/include/configs/MPC8560ADS.h
@@ -75,7 +75,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
diff --git a/include/configs/MPC8568MDS.h b/include/configs/MPC8568MDS.h
index c9a1539..7406ac3 100644
--- a/include/configs/MPC8568MDS.h
+++ b/include/configs/MPC8568MDS.h
@@ -60,7 +60,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
diff --git a/include/configs/MPC8569MDS.h b/include/configs/MPC8569MDS.h
index 341f6a8..df5572b 100644
--- a/include/configs/MPC8569MDS.h
+++ b/include/configs/MPC8569MDS.h
@@ -98,7 +98,7 @@ extern unsigned long get_clock_freq(void);
 #endif
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
diff --git a/include/configs/MPC8572DS.h b/include/configs/MPC8572DS.h
index c751144..63480ec 100644
--- a/include/configs/MPC8572DS.h
+++ b/include/configs/MPC8572DS.h
@@ -106,7 +106,7 @@
 
 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
@@ -322,6 +322,8 @@
 #define CONFIG_CMD_NAND		1
 #define CONFIG_NAND_FSL_ELBC	1
 #define CONFIG_SYS_NAND_BLOCK_SIZE    (128 * 1024)
+#define CONFIG_SYS_NAND_MAX_OOBFREE	5
+#define CONFIG_SYS_NAND_MAX_ECCPOS	56
 
 /* NAND boot: 4K NAND loader config */
 #define CONFIG_SYS_NAND_SPL_SIZE	0x1000
diff --git a/include/configs/MPC8610HPCD.h b/include/configs/MPC8610HPCD.h
index 97f5c87..41ebe31 100644
--- a/include/configs/MPC8610HPCD.h
+++ b/include/configs/MPC8610HPCD.h
@@ -92,7 +92,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS		CONFIG_SYS_CCSRBAR_PHYS_LOW
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD for DDR */
 #define CONFIG_DDR_SPD
diff --git a/include/configs/MPC8641HPCN.h b/include/configs/MPC8641HPCN.h
index 8ed5050..0e666ba 100644
--- a/include/configs/MPC8641HPCN.h
+++ b/include/configs/MPC8641HPCN.h
@@ -108,7 +108,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 /*
  * DDR Setup
  */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
diff --git a/include/configs/P1010RDB.h b/include/configs/P1010RDB.h
index c1cfbd4..eab386a 100644
--- a/include/configs/P1010RDB.h
+++ b/include/configs/P1010RDB.h
@@ -178,7 +178,7 @@
 #define CONFIG_PANIC_HANG		/* do not reset board on panic */
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_SYS_DDR_RAW_TIMING
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_SPD_BUS_NUM		1
@@ -313,6 +313,13 @@ extern unsigned long get_sdram_size(void);
 #define CONFIG_SYS_NAND_BASE_PHYS	CONFIG_SYS_NAND_BASE
 #endif
 
+#define CONFIG_MTD_DEVICE
+#define CONFIG_MTD_PARTITION
+#define CONFIG_CMD_MTDPARTS
+#define MTDIDS_DEFAULT			"nand0=ff800000.flash"
+#define MTDPARTS_DEFAULT		\
+	"mtdparts=ff800000.flash:2m(uboot-env),1m(dtb),5m(kernel),56m(fs),-(usr)"
+
 #define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 				| CSPR_PORT_SIZE_8	\
 				| CSPR_MSEL_NAND	\
diff --git a/include/configs/P1022DS.h b/include/configs/P1022DS.h
index 1470526..262c3e5 100644
--- a/include/configs/P1022DS.h
+++ b/include/configs/P1022DS.h
@@ -177,7 +177,7 @@
 /* DDR Setup */
 #define CONFIG_DDR_SPD
 #define CONFIG_VERY_BIG_RAM
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 
 #ifdef CONFIG_DDR_ECC
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
diff --git a/include/configs/P1023RDB.h b/include/configs/P1023RDB.h
index e49523e..7de6814 100644
--- a/include/configs/P1023RDB.h
+++ b/include/configs/P1023RDB.h
@@ -74,7 +74,7 @@ extern unsigned long get_clock_freq(void);
 #define CONFIG_CHIP_SELECTS_PER_CTRL	1
 
 #define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SYS_SDRAM_SIZE		512u	/* DDR is 512M */
 #define CONFIG_SYS_SPD_BUS_NUM          0
diff --git a/include/configs/P1_P2_RDB.h b/include/configs/P1_P2_RDB.h
index 282f5c1..b592c19 100644
--- a/include/configs/P1_P2_RDB.h
+++ b/include/configs/P1_P2_RDB.h
@@ -141,7 +141,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #endif
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #undef CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 
diff --git a/include/configs/P2020COME.h b/include/configs/P2020COME.h
index 9cc219e..15d2a43 100644
--- a/include/configs/P2020COME.h
+++ b/include/configs/P2020COME.h
@@ -105,7 +105,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 
diff --git a/include/configs/P2020DS.h b/include/configs/P2020DS.h
index 8a29eaa..9d3d9b3 100644
--- a/include/configs/P2020DS.h
+++ b/include/configs/P2020DS.h
@@ -109,9 +109,9 @@
 /* DDR Setup */
 #define CONFIG_VERY_BIG_RAM
 #ifdef CONFIG_DDR2
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #else
-#define CONFIG_FSL_DDR3		1
+#define CONFIG_SYS_FSL_DDR3		1
 #endif
 
 /* ECC will be enabled based on perf_mode environment variable */
diff --git a/include/configs/P2041RDB.h b/include/configs/P2041RDB.h
index 0df6f1a..b238574 100644
--- a/include/configs/P2041RDB.h
+++ b/include/configs/P2041RDB.h
@@ -175,7 +175,7 @@ unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
 #define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 
 #define CONFIG_SYS_SPD_BUS_NUM	0
 #define SPD_EEPROM_ADDRESS	0x52
diff --git a/include/configs/P4080DS.h b/include/configs/P4080DS.h
index b0cd7d5..2f89008 100644
--- a/include/configs/P4080DS.h
+++ b/include/configs/P4080DS.h
@@ -17,6 +17,12 @@
 #define CONFIG_MMC
 #define CONFIG_PCIE3
 
+#define CONFIG_CMD_SATA
+#define CONFIG_SATA_SIL
+#define CONFIG_SYS_SATA_MAX_DEVICE  2
+#define CONFIG_LIBATA
+#define CONFIG_LBA48
+
 #define CONFIG_SYS_SRIO
 #define CONFIG_SRIO1			/* SRIO port 1 */
 #define CONFIG_SRIO2			/* SRIO port 2 */
diff --git a/include/configs/PN62.h b/include/configs/PN62.h
deleted file mode 100644
index 2a82f94..0000000
--- a/include/configs/PN62.h
+++ /dev/null
@@ -1,285 +0,0 @@
-/*
- * (C) Copyright 2002
- * Wolfgang Grandegger, DENX Software Engineering, wg@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/* ------------------------------------------------------------------------- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC824X		1
-#define CONFIG_MPC8240		1
-#define CONFIG_PN62		1
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF00000
-
-#define CONFIG_CONS_INDEX	1
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_BSP
-
-#undef CONFIG_CMD_FLASH
-#undef CONFIG_CMD_IMLS
-#undef CONFIG_CMD_LOADS
-#undef CONFIG_CMD_SAVEENV
-#undef CONFIG_CMD_SOURCE
-
-
-#define CONFIG_BAUDRATE		19200	/* console baudrate		*/
-
-#define CONFIG_BOOTDELAY	1	/* autoboot after n seconds	*/
-
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
-
-#define CONFIG_SERVERIP		10.0.0.201
-#define CONFIG_IPADDR		10.0.0.200
-#define CONFIG_ROOTPATH		"/opt/eldk/ppc_82xx"
-#define CONFIG_NETMASK		255.255.255.0
-#undef CONFIG_BOOTARGS
-#if 0
-/* Boot Linux with NFS root filesystem */
-#define CONFIG_BOOTCOMMAND \
-			"setenv verify y;" \
-			"setenv bootargs console=ttyS0,19200 mem=31M quiet " \
-			"root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
-			"ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \
-			"loadp 100000; bootm"
-			/* "tftpboot 100000 uImage; bootm" */
-#else
-/* Boot Linux with RAMdisk based filesystem (initrd, BusyBox) */
-#define CONFIG_BOOTCOMMAND \
-			"setenv verify n;" \
-			"setenv bootargs console=ttyS0,19200 mem=31M quiet " \
-			"root=/dev/ram rw " \
-			"ip=${ipaddr}:${serverip}::${netmask}:pn62:eth0:off;" \
-			"loadp 200000; bootm"
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		1		/* undef to save memory		*/
-#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size	*/
-#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address		*/
-
-#define CONFIG_PRAM		1024		/* reserve 1 MB protected RAM	*/
-
-#define CONFIG_MISC_INIT_R	1		/* call misc_init_r() on init	*/
-
-#define CONFIG_HAS_ETH1		1		/* add support for eth1addr	*/
-
-#define CONFIG_SHOW_BOOT_PROGRESS 1		/* Show boot progress on LEDs   */
-
-/*
- * PCI stuff
- */
-#define CONFIG_PCI				/* include pci support		*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_PNP				/* we need Plug 'n Play		*/
-#if 0
-#define CONFIG_PCI_SCAN_SHOW			/* show PCI auto-scan at boot	*/
-#endif
-
-/*
- * Networking stuff
- */
-
-#define CONFIG_PCNET				/* there are 2 AMD PCnet 79C973	*/
-#define CONFIG_PCNET_79C973
-
-#define _IO_BASE		0xfe000000	/* points to PCI I/O space	*/
-
-
-/*
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_MAX_RAM_SIZE	0x10000000
-
-#define CONFIG_SYS_RESET_ADDRESS	0xfff00100
-
-#undef	CONFIG_SYS_RAMBOOT
-#define CONFIG_SYS_MONITOR_LEN		0x00030000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-
-
-#define CONFIG_SYS_INIT_RAM_ADDR	0x40000000
-#define CONFIG_SYS_INIT_RAM_SIZE	0x1000
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-
-
-#define CONFIG_SYS_NO_FLASH		1		/* There is no FLASH memory	*/
-
-#define CONFIG_ENV_IS_NOWHERE	1		/* Store ENV in memory only	*/
-#define CONFIG_ENV_OFFSET		0x00004000	/* Offset of Environment Sector */
-#define CONFIG_ENV_SIZE		0x00002000	/* Total Size of Environment Sector */
-
-#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x00004000	/* memtest works on		*/
-#define CONFIG_SYS_MEMTEST_END		0x01f00000	/* 0 ... 32 MB in DRAM		*/
-
-/*
- * Serial port configuration
- */
-
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-
-#define CONFIG_SYS_NS16550_CLK		1843200
-
-#define CONFIG_SYS_NS16550_COM1	0xff800008
-#define CONFIG_SYS_NS16550_COM2	0xff800000
-
-/*
- * Low Level Configuration Settings
- * (address mappings, register initial values, etc.)
- * You should know what you are doing if you make changes here.
- */
-
-#define CONFIG_SYS_CLK_FREQ  33333333	/* external frequency to pll */
-#define CONFIG_PLL_PCI_TO_MEM_MULTIPLIER  3
-
-#define CONFIG_SYS_EUMB_ADDR		0xFCE00000
-
-/* MCCR1 */
-#define CONFIG_SYS_ROMNAL		3	/* rom/flash next access time		*/
-#define CONFIG_SYS_ROMFAL		7	/* rom/flash access time		*/
-
-/* MCCR2 */
-#define CONFIG_SYS_ASRISE		6	/* ASRISE in clocks			*/
-#define CONFIG_SYS_ASFALL		12	/* ASFALL in clocks			*/
-#define CONFIG_SYS_REFINT		5600	/* REFINT in clocks			*/
-
-/* MCCR3 */
-#define CONFIG_SYS_BSTOPRE		0x3cf	/* Burst To Precharge			*/
-#define CONFIG_SYS_REFREC		2	/* Refresh to activate interval		*/
-#define CONFIG_SYS_RDLAT		3	/* data latency from read command	*/
-
-/* MCCR4 */
-#define CONFIG_SYS_PRETOACT		1	/* Precharge to activate interval	*/
-#define CONFIG_SYS_ACTTOPRE		3	/* Activate to Precharge interval	*/
-#define CONFIG_SYS_ACTORW		2	/* Activate to R/W			*/
-#define CONFIG_SYS_SDMODE_CAS_LAT	2	/* SDMODE CAS latency			*/
-#define CONFIG_SYS_SDMODE_WRAP		0	/* SDMODE Wrap type			*/
-#define CONFIG_SYS_SDMODE_BURSTLEN	2	/* SDMODE Burst length 2=4, 3=8		*/
-#define CONFIG_SYS_REGISTERD_TYPE_BUFFER   1
-
-/* Memory bank settings:
- *
- * only bits 20-29 are actually used from these vales to set the
- * start/qend address the upper two bits will be 0, and the lower 20
- * bits will be set to 0x00000 for a start address, or 0xfffff for an
- * end address
- */
-#define CONFIG_SYS_BANK0_START		0x00000000
-#define CONFIG_SYS_BANK0_END		(CONFIG_SYS_MAX_RAM_SIZE - 1)
-#define CONFIG_SYS_BANK0_ENABLE	1
-#define CONFIG_SYS_BANK1_START		0x00000000
-#define CONFIG_SYS_BANK1_END		0x00000000
-#define CONFIG_SYS_BANK1_ENABLE	0
-#define CONFIG_SYS_BANK2_START		0x00000000
-#define CONFIG_SYS_BANK2_END		0x00000000
-#define CONFIG_SYS_BANK2_ENABLE	0
-#define CONFIG_SYS_BANK3_START		0x00000000
-#define CONFIG_SYS_BANK3_END		0x00000000
-#define CONFIG_SYS_BANK3_ENABLE	0
-#define CONFIG_SYS_BANK4_START		0x00000000
-#define CONFIG_SYS_BANK4_END		0x00000000
-#define CONFIG_SYS_BANK4_ENABLE	0
-#define CONFIG_SYS_BANK5_START		0x00000000
-#define CONFIG_SYS_BANK5_END		0x00000000
-#define CONFIG_SYS_BANK5_ENABLE	0
-#define CONFIG_SYS_BANK6_START		0x00000000
-#define CONFIG_SYS_BANK6_END		0x00000000
-#define CONFIG_SYS_BANK6_ENABLE	0
-#define CONFIG_SYS_BANK7_START		0x00000000
-#define CONFIG_SYS_BANK7_END		0x00000000
-#define CONFIG_SYS_BANK7_ENABLE	0
-
-/*
- * Memory bank enable bitmask, specifying which of the banks defined above
- * are actually present. MSB is for bank #7, LSB is for bank #0.
- */
-#define CONFIG_SYS_BANK_ENABLE		0x01
-
-#define CONFIG_SYS_ODCR		0xff	/* configures line driver impedances,	*/
-					/* see 8240 book for bit definitions	*/
-#define CONFIG_SYS_PGMAX		0x32	/* how long the 8240 retains the	*/
-					/* currently accessed page in memory	*/
-					/* see 8240 book for details		*/
-
-/* SDRAM 0 - 256MB */
-#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-
-/* PCI memory space */
-#define CONFIG_SYS_IBAT2L	(0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT2U	(0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-/* Config addrs, etc */
-#define CONFIG_SYS_IBAT3L	(0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CONFIG_SYS_IBAT3U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
-#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
-#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
-#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
-#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
-#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
-#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
-#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Cache Configuration
- */
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8240 CPU			*/
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-#endif	/* __CONFIG_H */
diff --git a/include/configs/T1040QDS.h b/include/configs/T1040QDS.h
index 2738242..43a5778 100644
--- a/include/configs/T1040QDS.h
+++ b/include/configs/T1040QDS.h
@@ -32,6 +32,8 @@
 #ifdef CONFIG_RAMBOOT_PBL
 #define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
 #define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
+#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t1040qds/t1040_pbi.cfg
+#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t1040qds/t1040_rcw.cfg
 #endif
 
 /* High Level Configuration Options */
@@ -168,7 +170,7 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
 #define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_FSL_DDR_INTERACTIVE
 
 #define CONFIG_SYS_SPD_BUS_NUM	0
diff --git a/include/configs/T1040RDB.h b/include/configs/T1040RDB.h
new file mode 100644
index 0000000..7931231
--- /dev/null
+++ b/include/configs/T1040RDB.h
@@ -0,0 +1,690 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * T1040 RDB board configuration file
+ */
+#define CONFIG_T104xRDB
+#define CONFIG_T1040RDB
+#define CONFIG_PHYS_64BIT
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500			/* BOOKE e500 family */
+#define CONFIG_E500MC			/* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
+#define CONFIG_MPC85xx			/* MPC85xx/PQ3 platform */
+#define CONFIG_MP			/* support multiple processors */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+#define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC		CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC			/* Enable IFC Support */
+#define CONFIG_PCI			/* Enable PCI/PCIE */
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_PCIE1			/* PCIE controler 1 */
+#define CONFIG_PCIE2			/* PCIE controler 2 */
+#define CONFIG_PCIE3			/* PCIE controler 3 */
+#define CONFIG_PCIE4			/* PCIE controler 4 */
+
+#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
+
+#define CONFIG_FSL_LAW			/* Use common FSL init code */
+
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_NOWHERE
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#ifndef CONFIG_SYS_NO_FLASH
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS              0
+#define CONFIG_ENV_SPI_CS               0
+#define CONFIG_ENV_SPI_MAX_HZ           10000000
+#define CONFIG_ENV_SPI_MODE             0
+#define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
+#define CONFIG_ENV_SECT_SIZE            0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV          0
+#define CONFIG_ENV_SIZE			0x2000
+#define CONFIG_ENV_OFFSET		(512 * 1105)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+#else /* CONFIG_SYS_NO_FLASH */
+#define CONFIG_ENV_SIZE                0x2000
+#define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_SYS_CLK_FREQ	100000000
+#define CONFIG_DDR_CLK_FREQ	66666666
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#endif
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP		64	/* number of TLB1 entries */
+
+#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+/*
+ *  Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
+
+#define CONFIG_SYS_DCSRBAR		0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_SYS_FSL_DDR3
+
+#define CONFIG_SYS_SPD_BUS_NUM	0
+#define SPD_EEPROM_ADDRESS	0x51
+
+#define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE	0xe8000000
+#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+
+#define CONFIG_SYS_NOR_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
+				FTIM0_NOR_TEADC(0x5) | \
+				FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
+				FTIM1_NOR_TRAD_NOR(0x1A) |\
+				FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
+				FTIM2_NOR_TCH(0x4) | \
+				FTIM2_NOR_TWPH(0x0E) | \
+				FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3	0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
+
+/* CPLD on IFC */
+#define CONFIG_SYS_CPLD_BASE	0xffdf0000
+#define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_CPLD_BASE)
+#define CONFIG_SYS_CSPR2	(CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 \
+				| CSPR_MSEL_GPCM \
+				| CSPR_V)
+#define CONFIG_SYS_AMASK2	IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR2	0x0
+/* CPLD Timing parameters for IFC CS2 */
+#define CONFIG_SYS_CS2_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS2_FTIM1		(FTIM1_GPCM_TACO(0x0e) | \
+					FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS2_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
+					FTIM2_GPCM_TCH(0x0) | \
+					FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS2_FTIM3		0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE		0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
+				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
+				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
+				| CSOR_NAND_SPRZ_224/* Spare size = 224 */ \
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x07) | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0x0e)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
+					FTIM2_NAND_TREH(0x0a) | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW		11
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NAND_FTIM3
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)
+#define CONFIG_SERIAL_MULTI		/* Enable both serial ports */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL		/* Use FSL common I2C driver */
+#define CONFIG_SYS_FSL_I2C_SPEED	400000	/* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED	400000	/* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x119000
+
+/* I2C bus multiplexer */
+#define I2C_MUX_PCA_ADDR                0x70
+#define I2C_MUX_CH_DEFAULT      0x8
+
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED         10000000
+#define CONFIG_SF_DEFAULT_MODE          0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+#ifdef CONFIG_PCI
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#ifdef CONFIG_PCIE1
+#define	CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#define	CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
+#define	CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#ifdef CONFIG_PCIE2
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0x90000000
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc10000000ull
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#ifdef CONFIG_PCIE3
+#define CONFIG_SYS_PCIE3_MEM_VIRT	0xa0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc20000000ull
+#define CONFIG_SYS_PCIE3_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
+#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+/* controller 4, Base address 203000 */
+#ifdef CONFIG_PCIE4
+#define CONFIG_SYS_PCIE4_MEM_VIRT	0xb0000000
+#define CONFIG_SYS_PCIE4_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS	0xc30000000ull
+#define CONFIG_SYS_PCIE4_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE4_IO_VIRT	0xf8030000
+#define CONFIG_SYS_PCIE4_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull
+#define CONFIG_SYS_PCIE4_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+#define CONFIG_E1000
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif	/* CONFIG_PCI */
+
+/* SATA */
+#define CONFIG_FSL_SATA_V2
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CONFIG_SYS_SATA_MAX_DEVICE	1
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
+
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+* USB
+*/
+#define CONFIG_HAS_FSL_DR_USB
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#endif
+#endif
+
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS	25
+#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS	25
+#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 545KB (1089 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF40000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_SYS_FM1_DTSEC1_RISER_PHY_ADDR    0x1c
+#define CONFIG_SYS_FM1_DTSEC2_RISER_PHY_ADDR    0x1d
+#define CONFIG_SYS_FM1_DTSEC3_RISER_PHY_ADDR    0x1e
+#define CONFIG_SYS_FM1_DTSEC4_RISER_PHY_ADDR    0x1f
+
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"FM1@DTSEC1"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+#define CONFIG_UBOOTPATH	"u-boot.bin"	/* U-Boot image on TFTP server*/
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY	10	/*-1 disables auto-boot*/
+
+#define CONFIG_BAUDRATE	115200
+
+#define __USB_PHY_TYPE	utmi
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"hwconfig=fsl_ddr:ctlr_intlv=cacheline,"		\
+	"bank_intlv=cs0_cs1;"					\
+	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+	"netdev=eth0\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
+	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
+	"tftpflash=tftpboot $loadaddr $uboot && "		\
+	"protect off $ubootaddr +$filesize && "			\
+	"erase $ubootaddr +$filesize && "			\
+	"cp.b $loadaddr $ubootaddr $filesize && "		\
+	"protect on $ubootaddr +$filesize && "			\
+	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
+	"consoledev=ttyS0\0"					\
+	"ramdiskaddr=2000000\0"					\
+	"ramdiskfile=t1040rdb/ramdisk.uboot\0"			\
+	"fdtaddr=c00000\0"					\
+	"fdtfile=t1040rdb/t1040rdb.dtb\0"			\
+	"bdev=sda3\0"						\
+	"c=ffe\0"
+
+#define CONFIG_LINUX                       \
+	"setenv bootargs root=/dev/ram rw "            \
+	"console=$consoledev,$baudrate $othbootargs;"  \
+	"setenv ramdiskaddr 0x02000000;"               \
+	"setenv fdtaddr 0x00c00000;"		       \
+	"setenv loadaddr 0x1000000;"		       \
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT					\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND			\
+	"setenv bootargs root=/dev/nfs rw "	\
+	"nfsroot=$serverip:$rootpath "		\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $ramdiskaddr $ramdiskfile;"		\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/T1042RDB_PI.h b/include/configs/T1042RDB_PI.h
new file mode 100644
index 0000000..eff08e3
--- /dev/null
+++ b/include/configs/T1042RDB_PI.h
@@ -0,0 +1,694 @@
+/*
+ * Copyright 2013 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * T1042RDB_PI board configuration file
+ */
+#define CONFIG_T104xRDB
+#define CONFIG_T1042RDB_PI
+#define CONFIG_PHYS_64BIT
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
+#endif
+
+/* High Level Configuration Options */
+#define CONFIG_BOOKE
+#define CONFIG_E500			/* BOOKE e500 family */
+#define CONFIG_E500MC			/* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV		/* Category E.HV supported */
+#define CONFIG_MPC85xx			/* MPC85xx/PQ3 platform */
+#define CONFIG_MP			/* support multiple processors */
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+#define CONFIG_SYS_FSL_CPC		/* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC		CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC			/* Enable IFC Support */
+#define CONFIG_PCI			/* Enable PCI/PCIE */
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_PCIE1			/* PCIE controler 1 */
+#define CONFIG_PCIE2			/* PCIE controler 2 */
+#define CONFIG_PCIE3			/* PCIE controler 3 */
+#define CONFIG_PCIE4			/* PCIE controler 4 */
+
+#define CONFIG_FSL_PCI_INIT		/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT		/* enable 64-bit PCI resources */
+
+#define CONFIG_FSL_LAW			/* Use common FSL init code */
+
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_SYS_NO_FLASH
+#define CONFIG_ENV_IS_NOWHERE
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#ifndef CONFIG_SYS_NO_FLASH
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS              0
+#define CONFIG_ENV_SPI_CS               0
+#define CONFIG_ENV_SPI_MAX_HZ           10000000
+#define CONFIG_ENV_SPI_MODE             0
+#define CONFIG_ENV_SIZE                 0x2000          /* 8KB */
+#define CONFIG_ENV_OFFSET               0x100000        /* 1MB */
+#define CONFIG_ENV_SECT_SIZE            0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV          0
+#define CONFIG_ENV_SIZE			0x2000
+#define CONFIG_ENV_OFFSET		(512 * 1105)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE			CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET		(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+#else /* CONFIG_SYS_NO_FLASH */
+#define CONFIG_ENV_SIZE                0x2000
+#define CONFIG_ENV_SECT_SIZE   0x20000 /* 128K (one sector) */
+#endif
+
+#define CONFIG_SYS_CLK_FREQ	100000000
+#define CONFIG_DDR_CLK_FREQ	66666666
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BACKSIDE_L2_CACHE
+#define CONFIG_SYS_INIT_L2CSR0		L2CSR0_L2E
+#define CONFIG_BTB			/* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#endif
+
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#define CONFIG_ADDR_MAP
+#define CONFIG_SYS_NUM_ADDR_MAP		64	/* number of TLB1 entries */
+
+#define CONFIG_SYS_MEMTEST_START	0x00200000	/* memtest works on */
+#define CONFIG_SYS_MEMTEST_END		0x00400000
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_PANIC_HANG	/* do not reset board on panic */
+
+/*
+ *  Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR		0xFFFC0000
+
+#define CONFIG_SYS_DCSRBAR		0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS		0xf00000000ull
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+
+/* CONFIG_NUM_DDR_CONTROLLERS is defined in include/asm/config_mpc85xx.h */
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_DDR_RAW_TIMING
+#define CONFIG_SYS_FSL_DDR3
+
+#define CONFIG_SYS_SPD_BUS_NUM	0
+#define SPD_EEPROM_ADDRESS	0x51
+
+#define CONFIG_SYS_SDRAM_SIZE	4096	/* for fixed parameter use */
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE	0xe8000000
+#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+
+#define CONFIG_SYS_NOR_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
+				FTIM0_NOR_TEADC(0x5) | \
+				FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
+				FTIM1_NOR_TRAD_NOR(0x1A) |\
+				FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
+				FTIM2_NOR_TCH(0x4) | \
+				FTIM2_NOR_TWPH(0x0E) | \
+				FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3	0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS}
+
+/* CPLD on IFC */
+#define CONFIG_SYS_CPLD_BASE	0xffdf0000
+#define CONFIG_SYS_CPLD_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_CPLD_BASE)
+#define CONFIG_SYS_CSPR2	(CSPR_PHYS_ADDR(CONFIG_SYS_CPLD_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 \
+				| CSPR_MSEL_GPCM \
+				| CSPR_V)
+#define CONFIG_SYS_AMASK2	IFC_AMASK(64*1024)
+#define CONFIG_SYS_CSOR2	0x0
+/* CPLD Timing parameters for IFC CS2 */
+#define CONFIG_SYS_CS2_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS2_FTIM1		(FTIM1_GPCM_TACO(0x0e) | \
+					FTIM1_GPCM_TRAD(0x1f))
+#define CONFIG_SYS_CS2_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
+					FTIM2_GPCM_TCH(0x0) | \
+					FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS2_FTIM3		0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE		0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+				| CSPR_MSEL_NAND	/* MSEL = NAND */ \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
+				| CSOR_NAND_RAL_3	/* RAL = 3Byes */ \
+				| CSOR_NAND_PGS_4K	/* Page Size = 4K */ \
+				| CSOR_NAND_SPRZ_224/* Spare size = 224 */ \
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
+					FTIM0_NAND_TWP(0x18)   | \
+					FTIM0_NAND_TWCHT(0x07) | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)  | \
+					FTIM1_NAND_TRR(0x0e)   | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f) | \
+					FTIM2_NAND_TREH(0x0a) | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW		11
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(512 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NAND_FTIM3
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_BOARD_EARLY_INIT_R
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000	/* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+	((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+	  CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE		0x00004000
+
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+					GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
+
+/* Serial Port - controlled on board with jumper J8
+ * open - index 2
+ * shorted - index 1
+ */
+#define CONFIG_CONS_INDEX	1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_CCSRBAR+0x11D600)
+#define CONFIG_SERIAL_MULTI		/* Enable both serial ports */
+#define CONFIG_SYS_CONSOLE_IS_IN_ENV	/* determine from environment */
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/* I2C */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL		/* Use FSL common I2C driver */
+#define CONFIG_SYS_FSL_I2C_SPEED	400000	/* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_SPEED	400000	/* I2C speed in Hz */
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x119000
+
+/* I2C bus multiplexer */
+#define I2C_MUX_PCA_ADDR                0x70
+
+/*
+ * RTC configuration
+ */
+#define RTC
+#define CONFIG_RTC_DS1337               1
+#define CONFIG_SYS_I2C_RTC_ADDR         0x68
+
+/*DVI encoder*/
+#define CONFIG_HDMI_ENCODER_I2C_ADDR  0x75
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED         10000000
+#define CONFIG_SF_DEFAULT_MODE          0
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+
+#ifdef CONFIG_PCI
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#ifdef CONFIG_PCIE1
+#define	CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#define	CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
+#define	CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#ifdef CONFIG_PCIE2
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0x90000000
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc10000000ull
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#ifdef CONFIG_PCIE3
+#define CONFIG_SYS_PCIE3_MEM_VIRT	0xa0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc20000000ull
+#define CONFIG_SYS_PCIE3_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
+#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+/* controller 4, Base address 203000 */
+#ifdef CONFIG_PCIE4
+#define CONFIG_SYS_PCIE4_MEM_VIRT	0xb0000000
+#define CONFIG_SYS_PCIE4_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS	0xc30000000ull
+#define CONFIG_SYS_PCIE4_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE4_IO_VIRT	0xf8030000
+#define CONFIG_SYS_PCIE4_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull
+#define CONFIG_SYS_PCIE4_IO_SIZE	0x00010000	/* 64k */
+#endif
+
+#define CONFIG_PCI_PNP			/* do pci plug-and-play */
+#define CONFIG_E1000
+
+#define CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif	/* CONFIG_PCI */
+
+/* SATA */
+#define CONFIG_FSL_SATA_V2
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+
+#define CONFIG_SYS_SATA_MAX_DEVICE	1
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
+
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+* USB
+*/
+#define CONFIG_HAS_FSL_DR_USB
+
+#ifdef CONFIG_HAS_FSL_DR_USB
+#define CONFIG_USB_EHCI
+
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#endif
+#endif
+
+#define CONFIG_MMC
+
+#ifdef CONFIG_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR       CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_CMD_MMC
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS	25
+#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS	25
+#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 545KB (1089 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR		0xEFF40000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"FM1@DTSEC1"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO		/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SETEXPR
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory	*/
+#define CONFIG_CMDLINE_EDITING			/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE			/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH		"/opt/nfsroot"
+#define CONFIG_BOOTFILE		"uImage"
+#define CONFIG_UBOOTPATH	"u-boot.bin"	/* U-Boot image on TFTP server*/
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+
+#define CONFIG_BOOTDELAY	10	/*-1 disables auto-boot*/
+
+#define CONFIG_BAUDRATE	115200
+
+#define __USB_PHY_TYPE	utmi
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"hwconfig=fsl_ddr:ctlr_intlv=cacheline,"		\
+	"bank_intlv=cs0_cs1;"					\
+	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+	"netdev=eth0\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
+	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
+	"tftpflash=tftpboot $loadaddr $uboot && "		\
+	"protect off $ubootaddr +$filesize && "			\
+	"erase $ubootaddr +$filesize && "			\
+	"cp.b $loadaddr $ubootaddr $filesize && "		\
+	"protect on $ubootaddr +$filesize && "			\
+	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
+	"consoledev=ttyS0\0"					\
+	"ramdiskaddr=2000000\0"					\
+	"ramdiskfile=t1040rdb_pi/ramdisk.uboot\0"			\
+	"fdtaddr=c00000\0"					\
+	"fdtfile=t1040rdb_pi/t1040rdb_pi.dtb\0"				\
+	"bdev=sda3\0"						\
+	"c=ffe\0"
+
+#define CONFIG_LINUX                       \
+	"setenv bootargs root=/dev/ram rw "            \
+	"console=$consoledev,$baudrate $othbootargs;"  \
+	"setenv ramdiskaddr 0x02000000;"               \
+	"setenv fdtaddr 0x00c00000;"		       \
+	"setenv loadaddr 0x1000000;"		       \
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT					\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND			\
+	"setenv bootargs root=/dev/nfs rw "	\
+	"nfsroot=$serverip:$rootpath "		\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $ramdiskaddr $ramdiskfile;"		\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#endif
+
+#endif	/* __CONFIG_H */
diff --git a/include/configs/T2080QDS.h b/include/configs/T2080QDS.h
new file mode 100644
index 0000000..ad09816
--- /dev/null
+++ b/include/configs/T2080QDS.h
@@ -0,0 +1,805 @@
+/*
+ * Copyright 2011-2013 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+/*
+ * T2080 QDS board configuration file
+ */
+
+#ifndef __T2080QDS_H
+#define __T2080QDS_H
+
+#define CONFIG_T2080QDS
+#define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
+#define CONFIG_MMC
+#define CONFIG_SPI_FLASH
+#define CONFIG_USB_EHCI
+#define CONFIG_FSL_SATA_V2
+#define CONFIG_SYS_SRIO		/* Enable Serial RapidIO Support */
+#define CONFIG_SRIO1		/* SRIO port 1 */
+#define CONFIG_SRIO2		/* SRIO port 2 */
+
+/* High Level Configuration Options */
+#define CONFIG_PHYS_64BIT
+#define CONFIG_BOOKE
+#define CONFIG_E500		/* BOOKE e500 family */
+#define CONFIG_E500MC		/* BOOKE e500mc family */
+#define CONFIG_SYS_BOOK3E_HV	/* Category E.HV supported */
+#define CONFIG_MPC85xx		/* MPC85xx/PQ3 platform */
+#define CONFIG_MP		/* support multiple processors */
+#define CONFIG_ENABLE_36BIT_PHYS
+
+#ifdef CONFIG_PHYS_64BIT
+#define CONFIG_ADDR_MAP 1
+#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
+#endif
+
+#define CONFIG_SYS_FSL_CPC	/* Corenet Platform Cache */
+#define CONFIG_SYS_NUM_CPC	CONFIG_NUM_DDR_CONTROLLERS
+#define CONFIG_FSL_IFC		/* Enable IFC Support */
+#define CONFIG_FSL_LAW		/* Use common FSL init code */
+#define CONFIG_ENV_OVERWRITE
+
+#ifdef CONFIG_RAMBOOT_PBL
+#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
+#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
+#define CONFIG_PBLPBI_CONFIG $(SRCTREE)/board/freescale/t2080qds/t2080_pbi.cfg
+#define CONFIG_PBLRCW_CONFIG $(SRCTREE)/board/freescale/t2080qds/t2080_rcw.cfg
+#endif
+
+#define CONFIG_SRIO_PCIE_BOOT_MASTER
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+/* Set 1M boot space */
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
+#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
+		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
+#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
+#define CONFIG_SYS_NO_FLASH
+#endif
+
+#ifndef CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_TEXT_BASE	0xeff80000
+#endif
+
+#ifndef CONFIG_RESET_VECTOR_ADDRESS
+#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
+#endif
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_SYS_CACHE_STASHING
+#define CONFIG_BTB		/* toggle branch predition */
+#define CONFIG_DDR_ECC
+#ifdef CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
+#endif
+
+#ifdef CONFIG_SYS_NO_FLASH
+#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_ENV_IS_NOWHERE
+#endif
+#else
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+#endif
+
+#if defined(CONFIG_SPIFLASH)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_SPI_FLASH
+#define CONFIG_ENV_SPI_BUS	0
+#define CONFIG_ENV_SPI_CS	0
+#define CONFIG_ENV_SPI_MAX_HZ	10000000
+#define CONFIG_ENV_SPI_MODE	0
+#define CONFIG_ENV_SIZE		0x2000	   /* 8KB */
+#define CONFIG_ENV_OFFSET	0x100000   /* 1MB */
+#define CONFIG_ENV_SECT_SIZE	0x10000
+#elif defined(CONFIG_SDCARD)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_MMC
+#define CONFIG_SYS_MMC_ENV_DEV	0
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_OFFSET	(512 * 1105)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_EXTRA_ENV_RELOC
+#define CONFIG_ENV_IS_IN_NAND
+#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
+#define CONFIG_ENV_OFFSET	(5 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+#define CONFIG_ENV_IS_IN_REMOTE
+#define CONFIG_ENV_ADDR		0xffe20000
+#define CONFIG_ENV_SIZE		0x2000
+#elif defined(CONFIG_ENV_IS_NOWHERE)
+#define CONFIG_ENV_SIZE		0x2000
+#else
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE		0x2000
+#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
+#endif
+
+#ifndef __ASSEMBLY__
+unsigned long get_board_sys_clk(void);
+unsigned long get_board_ddr_clk(void);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk()
+#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk()
+
+/*
+ * Config the L3 Cache as L3 SRAM
+ */
+#define CONFIG_SYS_INIT_L3_ADDR	 CONFIG_RAMBOOT_TEXT_BASE
+
+#define CONFIG_SYS_DCSRBAR	0xf0000000
+#define CONFIG_SYS_DCSRBAR_PHYS	0xf00000000ull
+
+/* EEPROM */
+#define CONFIG_ID_EEPROM
+#define CONFIG_SYS_I2C_EEPROM_NXID
+#define CONFIG_SYS_EEPROM_BUS_NUM	0
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
+
+/*
+ * DDR Setup
+ */
+#define CONFIG_VERY_BIG_RAM
+#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_DIMM_SLOTS_PER_CTLR	1
+#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
+#define CONFIG_DDR_SPD
+#define CONFIG_SYS_FSL_DDR3
+#define CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SYS_SPD_BUS_NUM	0
+#define CONFIG_SYS_SDRAM_SIZE	2048	/* for fixed parameter use */
+#define SPD_EEPROM_ADDRESS1	0x51
+#define SPD_EEPROM_ADDRESS2	0x52
+#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1
+#define CTRL_INTLV_PREFERED	cacheline
+
+/*
+ * IFC Definitions
+ */
+#define CONFIG_SYS_FLASH_BASE		0xe0000000
+#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
+				+ 0x8000000) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR1_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
+				CSPR_PORT_SIZE_16 | \
+				CSPR_MSEL_NOR | \
+				CSPR_V)
+#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
+/* NOR Flash Timing Params */
+#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
+
+#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
+				FTIM0_NOR_TEADC(0x5) | \
+				FTIM0_NOR_TEAHC(0x5))
+#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
+				FTIM1_NOR_TRAD_NOR(0x1A) |\
+				FTIM1_NOR_TSEQRAD_NOR(0x13))
+#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
+				FTIM2_NOR_TCH(0x4) | \
+				FTIM2_NOR_TWPH(0x0E) | \
+				FTIM2_NOR_TWP(0x1c))
+#define CONFIG_SYS_NOR_FTIM3	0x0
+
+#define CONFIG_SYS_FLASH_QUIET_TEST
+#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
+
+#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+
+#define CONFIG_SYS_FLASH_EMPTY_INFO
+#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS \
+					+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
+
+#define CONFIG_FSL_QIXIS	/* use common QIXIS code */
+#define QIXIS_BASE			0xffdf0000
+#define QIXIS_LBMAP_SWITCH		6
+#define QIXIS_LBMAP_MASK		0x0f
+#define QIXIS_LBMAP_SHIFT		0
+#define QIXIS_LBMAP_DFLTBANK		0x00
+#define QIXIS_LBMAP_ALTBANK		0x04
+#define QIXIS_RST_CTL_RESET		0x83
+#define QIXIS_RST_FORCE_MEM		0x1
+#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
+#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
+#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
+#define QIXIS_BASE_PHYS		(0xf00000000ull | QIXIS_BASE)
+
+#define CONFIG_SYS_CSPR3_EXT	(0xf)
+#define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 \
+				| CSPR_MSEL_GPCM \
+				| CSPR_V)
+#define CONFIG_SYS_AMASK3	IFC_AMASK(4*1024)
+#define CONFIG_SYS_CSOR3	0x0
+/* QIXIS Timing parameters for IFC CS3 */
+#define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
+					FTIM0_GPCM_TEADC(0x0e) | \
+					FTIM0_GPCM_TEAHC(0x0e))
+#define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
+					FTIM1_GPCM_TRAD(0x3f))
+#define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
+					FTIM2_GPCM_TCH(0x0) | \
+					FTIM2_GPCM_TWP(0x1f))
+#define CONFIG_SYS_CS3_FTIM3		0x0
+
+/* NAND Flash on IFC */
+#define CONFIG_NAND_FSL_IFC
+#define CONFIG_SYS_NAND_BASE		0xff800000
+#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
+
+#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
+#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
+				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
+				| CSPR_MSEL_NAND	 /* MSEL = NAND */ \
+				| CSPR_V)
+#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
+
+#define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
+				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
+				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */	    \
+				| CSOR_NAND_RAL_3	/* RAL = 2Byes */   \
+				| CSOR_NAND_PGS_2K	/* Page Size = 2K */\
+				| CSOR_NAND_SPRZ_64	/* Spare size = 64 */\
+				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
+
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+
+/* ONFI NAND Flash mode0 Timing Params */
+#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
+					FTIM0_NAND_TWP(0x18)    | \
+					FTIM0_NAND_TWCHT(0x07)  | \
+					FTIM0_NAND_TWH(0x0a))
+#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
+					FTIM1_NAND_TWBE(0x39)   | \
+					FTIM1_NAND_TRR(0x0e)    | \
+					FTIM1_NAND_TRP(0x18))
+#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f)  | \
+					FTIM2_NAND_TREH(0x0a)   | \
+					FTIM2_NAND_TWHRE(0x1e))
+#define CONFIG_SYS_NAND_FTIM3		0x0
+
+#define CONFIG_SYS_NAND_DDR_LAW		11
+#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+
+#if defined(CONFIG_NAND)
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
+#else
+#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
+#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
+#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
+#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
+#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
+#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
+#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
+#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
+#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
+#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
+#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
+#endif
+#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
+#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
+#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
+#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
+#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
+#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
+#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
+#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
+
+#if defined(CONFIG_RAMBOOT_PBL)
+#define CONFIG_SYS_RAMBOOT
+#endif
+
+#define CONFIG_SYS_MONITOR_BASE	 CONFIG_SYS_TEXT_BASE
+#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
+#define CONFIG_MISC_INIT_R
+#define CONFIG_HWCONFIG
+
+/* define to use L1 as initial stack */
+#define CONFIG_L1_INIT_RAM
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000 /* Initial L1 address */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe0ec000
+/* The assembler doesn't like typecast */
+#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
+			((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
+			CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
+#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
+						GENERATED_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
+#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
+#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
+
+/* Use the HUSH parser */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/* new uImage format support */
+#define CONFIG_FIT
+#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
+
+/*
+ * I2C
+ */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
+#define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
+#define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
+#define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
+#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
+#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
+#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
+#define CONFIG_SYS_FSL_I2C_SPEED   100000
+#define CONFIG_SYS_FSL_I2C2_SPEED  100000
+#define CONFIG_SYS_FSL_I2C3_SPEED  100000
+#define CONFIG_SYS_FSL_I2C4_SPEED  100000
+#define I2C_MUX_PCA_ADDR_PRI	0x77 /* I2C bus multiplexer,primary */
+#define I2C_MUX_PCA_ADDR_SEC1	0x75 /* I2C bus multiplexer,secondary 1 */
+#define I2C_MUX_PCA_ADDR_SEC2	0x76 /* I2C bus multiplexer,secondary 2 */
+#define I2C_MUX_CH_DEFAULT	0x8
+
+
+/*
+ * RapidIO
+ */
+#define CONFIG_SYS_SRIO1_MEM_VIRT	0xa0000000
+#define CONFIG_SYS_SRIO1_MEM_PHYS	0xc20000000ull
+#define CONFIG_SYS_SRIO1_MEM_SIZE	0x10000000 /* 256M */
+#define CONFIG_SYS_SRIO2_MEM_VIRT	0xb0000000
+#define CONFIG_SYS_SRIO2_MEM_PHYS	0xc30000000ull
+#define CONFIG_SYS_SRIO2_MEM_SIZE	0x10000000 /* 256M */
+/*
+ * for slave u-boot IMAGE instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x80000 /* 512K */
+#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
+/*
+ * for slave UCODE and ENV instored in master memory space,
+ * PHYS must be aligned based on the SIZE
+ */
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
+#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000	/* 256K */
+
+/* slave core release by master*/
+#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
+#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
+
+/*
+ * SRIO_PCIE_BOOT - SLAVE
+ */
+#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
+#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
+		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
+#endif
+
+/*
+ * eSPI - Enhanced SPI
+ */
+#ifdef CONFIG_SPI_FLASH
+#define CONFIG_FSL_ESPI
+#define CONFIG_SPI_FLASH_SST
+#define CONFIG_SPI_FLASH_STMICRO
+#define CONFIG_SPI_FLASH_SPANSION
+#define CONFIG_CMD_SF
+#define CONFIG_SF_DEFAULT_SPEED	 10000000
+#define CONFIG_SF_DEFAULT_MODE	  0
+#endif
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+#define CONFIG_PCI		/* Enable PCI/PCIE */
+#define CONFIG_PCIE1		/* PCIE controler 1 */
+#define CONFIG_PCIE2		/* PCIE controler 2 */
+#define CONFIG_PCIE3		/* PCIE controler 3 */
+#define CONFIG_PCIE4		/* PCIE controler 4 */
+#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
+/* controller 1, direct to uli, tgtid 3, Base address 20000 */
+#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
+#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
+#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000      /* 512M */
+#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
+#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
+#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 2, Slot 2, tgtid 2, Base address 201000 */
+#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
+#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
+#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
+#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
+#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 3, Slot 1, tgtid 1, Base address 202000 */
+#define CONFIG_SYS_PCIE3_MEM_VIRT	0xb0000000
+#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc30000000ull
+#define CONFIG_SYS_PCIE3_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
+#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
+#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
+
+/* controller 4, Base address 203000 */
+#define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
+#define CONFIG_SYS_PCIE4_MEM_BUS	0xe0000000
+#define CONFIG_SYS_PCIE4_MEM_PHYS	0xc40000000ull
+#define CONFIG_SYS_PCIE4_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCIE4_IO_BUS		0x00000000
+#define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull
+#define CONFIG_SYS_PCIE4_IO_SIZE	0x00010000	/* 64k */
+
+#ifdef CONFIG_PCI
+#define CONFIG_PCI_INDIRECT_BRIDGE
+#define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata LSZ ADD */
+#define CONFIG_NET_MULTI
+#define CONFIG_E1000
+#define CONFIG_PCI_PNP		/* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
+#define CONFIG_DOS_PARTITION
+#endif
+
+/* Qman/Bman */
+#ifndef CONFIG_NOBQFMAN
+#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
+#define CONFIG_SYS_BMAN_NUM_PORTALS	18
+#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
+#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
+#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
+#define CONFIG_SYS_QMAN_NUM_PORTALS	18
+#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
+#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
+#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
+
+#define CONFIG_SYS_DPAA_FMAN
+#define CONFIG_SYS_DPAA_PME
+#define CONFIG_SYS_PMAN
+#define CONFIG_SYS_DPAA_DCE
+#define CONFIG_SYS_DPAA_RMAN		/* RMan */
+#define CONFIG_SYS_INTERLAKEN
+
+/* Default address of microcode for the Linux Fman driver */
+#if defined(CONFIG_SPIFLASH)
+/*
+ * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
+ * env, so we got 0x110000.
+ */
+#define CONFIG_SYS_QE_FW_IN_SPIFLASH
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
+#elif defined(CONFIG_SDCARD)
+/*
+ * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
+ * about 545KB (1089 blocks), Env is stored after the image, and the env size is
+ * 0x2000 (16 blocks), 8 + 1089 + 16 = 1113, enlarge it to 1130.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1130)
+#elif defined(CONFIG_NAND)
+#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	(6 * CONFIG_SYS_NAND_BLOCK_SIZE)
+#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
+/*
+ * Slave has no ucode locally, it can fetch this from remote. When implementing
+ * in two corenet boards, slave's ucode could be stored in master's memory
+ * space, the address can be mapped from slave TLB->slave LAW->
+ * slave SRIO or PCIE outbound window->master inbound window->
+ * master LAW->the ucode address in master's memory space.
+ */
+#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
+#else
+#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
+#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF40000
+#endif
+#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
+#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
+#endif /* CONFIG_NOBQFMAN */
+
+#ifdef CONFIG_SYS_DPAA_FMAN
+#define CONFIG_FMAN_ENET
+#define CONFIG_PHYLIB_10G
+#define CONFIG_PHY_VITESSE
+#define CONFIG_PHY_REALTEK
+#define CONFIG_PHY_TERANETICS
+#define RGMII_PHY1_ADDR	0x1
+#define RGMII_PHY2_ADDR	0x2
+#define FM1_10GEC1_PHY_ADDR	  0x3
+#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
+#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
+#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
+#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
+#endif
+
+#ifdef CONFIG_FMAN_ENET
+#define CONFIG_MII		/* MII PHY management */
+#define CONFIG_ETHPRIME		"FM1@DTSEC3"
+#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
+#endif
+
+/*
+ * SATA
+ */
+#ifdef CONFIG_FSL_SATA_V2
+#define CONFIG_LIBATA
+#define CONFIG_FSL_SATA
+#define CONFIG_SYS_SATA_MAX_DEVICE	2
+#define CONFIG_SATA1
+#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
+#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
+#define CONFIG_SATA2
+#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
+#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
+#define CONFIG_LBA48
+#define CONFIG_CMD_SATA
+#define CONFIG_DOS_PARTITION
+#define CONFIG_CMD_EXT2
+#endif
+
+/*
+ * USB
+ */
+#ifdef CONFIG_USB_EHCI
+#define CONFIG_CMD_USB
+#define CONFIG_USB_STORAGE
+#define CONFIG_USB_EHCI_FSL
+#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
+#define CONFIG_CMD_EXT2
+#define CONFIG_HAS_FSL_DR_USB
+#endif
+
+/*
+ * SDHC
+ */
+#ifdef CONFIG_MMC
+#define CONFIG_CMD_MMC
+#define CONFIG_FSL_ESDHC
+#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
+#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
+#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
+#define CONFIG_GENERIC_MMC
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_DOS_PARTITION
+#endif
+
+/*
+ * Environment
+ */
+#define CONFIG_LOADS_ECHO	/* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ERRATA
+#define CONFIG_CMD_GREPENV
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SETEXPR
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_BDI
+
+#ifdef CONFIG_PCI
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_NET
+#endif
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
+#define CONFIG_AUTO_COMPLETE		/* add autocompletion support */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT	"=> "	  /* Monitor Command Prompt */
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_SYS_CBSIZE	1024	  /* Console I/O Buffer Size */
+#else
+#define CONFIG_SYS_CBSIZE	256	  /* Console I/O Buffer Size */
+#endif
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000	/* decrementer freq: 1ms ticks*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 64 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
+#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
+
+#ifdef CONFIG_CMD_KGDB
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
+#endif
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ROOTPATH	 "/opt/nfsroot"
+#define CONFIG_BOOTFILE	 "uImage"
+#define CONFIG_UBOOTPATH "u-boot.bin"	/* U-Boot image on TFTP server */
+
+/* default location for tftp and bootm */
+#define CONFIG_LOADADDR		1000000
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */
+#define __USB_PHY_TYPE		utmi
+
+#define	CONFIG_EXTRA_ENV_SETTINGS				\
+	"hwconfig=fsl_ddr:"					\
+	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","	\
+	"bank_intlv=auto;"					\
+	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
+	"netdev=eth0\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
+	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
+	"tftpflash=tftpboot $loadaddr $uboot && "		\
+	"protect off $ubootaddr +$filesize && "			\
+	"erase $ubootaddr +$filesize && "			\
+	"cp.b $loadaddr $ubootaddr $filesize && "		\
+	"protect on $ubootaddr +$filesize && "			\
+	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
+	"consoledev=ttyS0\0"					\
+	"ramdiskaddr=2000000\0"					\
+	"ramdiskfile=t2080qds/ramdisk.uboot\0"			\
+	"fdtaddr=c00000\0"					\
+	"fdtfile=t2080qds/t2080qds.dtb\0"			\
+	"bdev=sda3\0"						\
+	"c=ffe\0"
+
+/*
+ * For emulation this causes u-boot to jump to the start of the
+ * proof point app code automatically
+ */
+#define CONFIG_PROOF_POINTS				\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"cpu 1 release 0x29000000 - - -;"		\
+	"cpu 2 release 0x29000000 - - -;"		\
+	"cpu 3 release 0x29000000 - - -;"		\
+	"cpu 4 release 0x29000000 - - -;"		\
+	"cpu 5 release 0x29000000 - - -;"		\
+	"cpu 6 release 0x29000000 - - -;"		\
+	"cpu 7 release 0x29000000 - - -;"		\
+	"go 0x29000000"
+
+#define CONFIG_HVBOOT				\
+	"setenv bootargs config-addr=0x60000000; "	\
+	"bootm 0x01000000 - 0x00f00000"
+
+#define CONFIG_ALU				\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"cpu 1 release 0x01000000 - - -;"		\
+	"cpu 2 release 0x01000000 - - -;"		\
+	"cpu 3 release 0x01000000 - - -;"		\
+	"cpu 4 release 0x01000000 - - -;"		\
+	"cpu 5 release 0x01000000 - - -;"		\
+	"cpu 6 release 0x01000000 - - -;"		\
+	"cpu 7 release 0x01000000 - - -;"		\
+	"go 0x01000000"
+
+#define CONFIG_LINUX				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"setenv ramdiskaddr 0x02000000;"		\
+	"setenv fdtaddr 0x00c00000;"			\
+	"setenv loadaddr 0x1000000;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_HDBOOT					\
+	"setenv bootargs root=/dev/$bdev rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_NFSBOOTCOMMAND			\
+	"setenv bootargs root=/dev/nfs rw "	\
+	"nfsroot=$serverip:$rootpath "		\
+	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $loadaddr $bootfile;"		\
+	"tftp $fdtaddr $fdtfile;"		\
+	"bootm $loadaddr - $fdtaddr"
+
+#define CONFIG_RAMBOOTCOMMAND				\
+	"setenv bootargs root=/dev/ram rw "		\
+	"console=$consoledev,$baudrate $othbootargs;"	\
+	"tftp $ramdiskaddr $ramdiskfile;"		\
+	"tftp $loadaddr $bootfile;"			\
+	"tftp $fdtaddr $fdtfile;"			\
+	"bootm $loadaddr $ramdiskaddr $fdtaddr"
+
+#define CONFIG_BOOTCOMMAND		CONFIG_LINUX
+
+#ifdef CONFIG_SECURE_BOOT
+#include <asm/fsl_secure_boot.h>
+#undef CONFIG_CMD_USB
+#endif
+
+#endif	/* __T2080QDS_H */
diff --git a/include/configs/T4240QDS.h b/include/configs/T4240QDS.h
index 3777ccb..c96df54 100644
--- a/include/configs/T4240QDS.h
+++ b/include/configs/T4240QDS.h
@@ -229,6 +229,8 @@ unsigned long get_board_ddr_clk(void);
 #define CONFIG_CMD_NAND
 
 #define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+#define CONFIG_SYS_NAND_MAX_OOBFREE	2
+#define CONFIG_SYS_NAND_MAX_ECCPOS	256
 
 #if defined(CONFIG_NAND)
 #define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index 2bf1986..61fdeba 100644
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -324,6 +324,8 @@
 #define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE + 0, CONFIG_SYS_NAND_BASE + 2,	\
 				  CONFIG_SYS_NAND_BASE + 4, CONFIG_SYS_NAND_BASE + 6 }
 #define CONFIG_SYS_NAND_QUIET_TEST	1	/* don't warn upon unknown NAND flash	*/
+#define CONFIG_SYS_NAND_MAX_OOBFREE	2
+#define CONFIG_SYS_NAND_MAX_ECCPOS	56
 
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
diff --git a/include/configs/am335x_evm.h b/include/configs/am335x_evm.h
index e8a6ca1..8af4d6a 100644
--- a/include/configs/am335x_evm.h
+++ b/include/configs/am335x_evm.h
@@ -182,7 +182,6 @@
 #define CONFIG_SYS_NS16550_COM6		0x481aa000	/* UART5 */
 #define CONFIG_BAUDRATE			115200
 
-/* I2C Configuration */
 #define CONFIG_CMD_EEPROM
 #define CONFIG_ENV_EEPROM_IS_ON_I2C
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* Main EEPROM */
@@ -224,6 +223,8 @@
 #define CONFIG_SPL_LDSCRIPT		"$(CPUDIR)/am33xx/u-boot-spl.lds"
 
 #ifdef CONFIG_NAND
+#define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_ELM
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_PAGE_COUNT	(CONFIG_SYS_NAND_BLOCK_SIZE / \
 					 CONFIG_SYS_NAND_PAGE_SIZE)
@@ -241,7 +242,8 @@
 
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	14
-
+#define CONFIG_SYS_NAND_ONFI_DETECTION
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_BCH8_CODE_HW
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
 #endif
diff --git a/include/configs/am335x_igep0033.h b/include/configs/am335x_igep0033.h
index 2c69d4e..115d1b3 100644
--- a/include/configs/am335x_igep0033.h
+++ b/include/configs/am335x_igep0033.h
@@ -187,6 +187,7 @@
 /* NAND support */
 #define CONFIG_NAND
 #define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_ELM
 #define GPMC_NAND_ECC_LP_x16_LAYOUT	1
 #define CONFIG_SYS_NAND_BASE		(0x08000000)	/* phys address CS0 */
 #define CONFIG_SYS_MAX_NAND_DEVICE	1
@@ -263,6 +264,7 @@
 
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	14
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_BCH8_CODE_HW
 
 #define	CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 
diff --git a/include/configs/am3517_crane.h b/include/configs/am3517_crane.h
index c5e67bf..468fb43 100644
--- a/include/configs/am3517_crane.h
+++ b/include/configs/am3517_crane.h
@@ -142,10 +142,10 @@
 #undef CONFIG_CMD_IMLS		/* List all found images	*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C			1
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 #undef CONFIG_CMD_NET
 #undef CONFIG_CMD_NFS
@@ -340,6 +340,7 @@
 						10, 11, 12, 13}
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
 
diff --git a/include/configs/am3517_evm.h b/include/configs/am3517_evm.h
index 5e259f5..1fa477a 100644
--- a/include/configs/am3517_evm.h
+++ b/include/configs/am3517_evm.h
@@ -136,10 +136,10 @@
 #undef CONFIG_CMD_IMLS		/* List all found images	*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C			1
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /*
  * Ethernet
@@ -344,6 +344,7 @@
 						10, 11, 12, 13}
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
 
diff --git a/include/configs/bct-brettl2.h b/include/configs/bct-brettl2.h
index ce09c2e..5b09b45 100644
--- a/include/configs/bct-brettl2.h
+++ b/include/configs/bct-brettl2.h
@@ -111,8 +111,8 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-	arch/blackfin/lib/libblackfin.o (.text*); \
-	arch/blackfin/cpu/libblackfin.o (.text*); \
+	arch/blackfin/lib/built-in.o (.text*); \
+	arch/blackfin/cpu/built-in.o (.text*); \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);
 #endif
diff --git a/include/configs/bf533-stamp.h b/include/configs/bf533-stamp.h
index 7144c63..a22c868 100644
--- a/include/configs/bf533-stamp.h
+++ b/include/configs/bf533-stamp.h
@@ -155,8 +155,8 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-	arch/blackfin/lib/libblackfin.o (.text*); \
-	arch/blackfin/cpu/libblackfin.o (.text*); \
+	arch/blackfin/lib/built-in.o (.text*); \
+	arch/blackfin/cpu/built-in.o (.text*); \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);
 #endif
diff --git a/include/configs/bf537-pnav.h b/include/configs/bf537-pnav.h
index 62bd3bf..3aa3d50 100644
--- a/include/configs/bf537-pnav.h
+++ b/include/configs/bf537-pnav.h
@@ -111,8 +111,8 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-	arch/blackfin/lib/libblackfin.o (.text*); \
-	arch/blackfin/cpu/libblackfin.o (.text*); \
+	arch/blackfin/lib/built-in.o (.text*); \
+	arch/blackfin/cpu/built-in.o (.text*); \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);
 #endif
diff --git a/include/configs/bf537-stamp.h b/include/configs/bf537-stamp.h
index 25cebf8..02945be 100644
--- a/include/configs/bf537-stamp.h
+++ b/include/configs/bf537-stamp.h
@@ -118,8 +118,8 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-	arch/blackfin/lib/libblackfin.o (.text*); \
-	arch/blackfin/cpu/libblackfin.o (.text*); \
+	arch/blackfin/lib/built-in.o (.text*); \
+	arch/blackfin/cpu/built-in.o (.text*); \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);
 #endif
diff --git a/include/configs/bf538f-ezkit.h b/include/configs/bf538f-ezkit.h
index 77822e7..ffb0caf 100644
--- a/include/configs/bf538f-ezkit.h
+++ b/include/configs/bf538f-ezkit.h
@@ -115,8 +115,8 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-	arch/blackfin/lib/libblackfin.o (.text*); \
-	arch/blackfin/cpu/libblackfin.o (.text*); \
+	arch/blackfin/lib/built-in.o (.text*); \
+	arch/blackfin/cpu/built-in.o (.text*); \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);
 #endif
diff --git a/include/configs/cm-bf537e.h b/include/configs/cm-bf537e.h
index 77f47d9..8f10eba 100644
--- a/include/configs/cm-bf537e.h
+++ b/include/configs/cm-bf537e.h
@@ -112,8 +112,8 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-	arch/blackfin/lib/libblackfin.o (.text*); \
-	arch/blackfin/cpu/libblackfin.o (.text*); \
+	arch/blackfin/lib/built-in.o (.text*); \
+	arch/blackfin/cpu/built-in.o (.text*); \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);
 #endif
diff --git a/include/configs/cm-bf537u.h b/include/configs/cm-bf537u.h
index 55e61d6..a1c8e8a 100644
--- a/include/configs/cm-bf537u.h
+++ b/include/configs/cm-bf537u.h
@@ -110,8 +110,8 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-	arch/blackfin/lib/libblackfin.o (.text*); \
-	arch/blackfin/cpu/libblackfin.o (.text*); \
+	arch/blackfin/lib/built-in.o (.text*); \
+	arch/blackfin/cpu/built-in.o (.text*); \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);
 #endif
diff --git a/include/configs/cm_t35.h b/include/configs/cm_t35.h
index a490fc3..e72187e 100644
--- a/include/configs/cm_t35.h
+++ b/include/configs/cm_t35.h
@@ -141,10 +141,10 @@
 #undef CONFIG_CMD_IMLS		/* List all found images	*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
 #define CONFIG_I2C_MULTI_BUS
@@ -326,5 +326,8 @@
 #define CONFIG_SPLASH_SCREEN
 #define CONFIG_CMD_BMP
 #define CONFIG_BMP_16BPP
+#define CONFIG_SCF0403_LCD
+
+#define CONFIG_OMAP3_SPI
 
 #endif /* __CONFIG_H */
diff --git a/include/configs/controlcenterd.h b/include/configs/controlcenterd.h
index 413f086..46d4f98 100644
--- a/include/configs/controlcenterd.h
+++ b/include/configs/controlcenterd.h
@@ -138,7 +138,7 @@
 #define CONFIG_SYS_SDRAM_SIZE 1024
 #define CONFIG_VERY_BIG_RAM
 
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_NUM_DDR_CONTROLLERS	1
 #define CONFIG_DIMM_SLOTS_PER_CTLR	1
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(2 * CONFIG_DIMM_SLOTS_PER_CTLR)
diff --git a/include/configs/corenet_ds.h b/include/configs/corenet_ds.h
index 562caa5..665295c 100644
--- a/include/configs/corenet_ds.h
+++ b/include/configs/corenet_ds.h
@@ -173,7 +173,7 @@
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
 #define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 
 #define CONFIG_SYS_SPD_BUS_NUM	1
 #define SPD_EEPROM_ADDRESS1	0x51
diff --git a/include/configs/devkit8000.h b/include/configs/devkit8000.h
index 8343891..4f43ba9 100644
--- a/include/configs/devkit8000.h
+++ b/include/configs/devkit8000.h
@@ -90,10 +90,10 @@
 #define CONFIG_DOS_PARTITION		1
 
 /* I2C */
-#define CONFIG_HARD_I2C			1
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /* TWL4030 */
 #define CONFIG_TWL4030_POWER		1
@@ -327,6 +327,7 @@
 
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW
 
 #define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE
 
diff --git a/include/configs/dig297.h b/include/configs/dig297.h
index c19c4c7..5049afc 100644
--- a/include/configs/dig297.h
+++ b/include/configs/dig297.h
@@ -123,10 +123,10 @@
 #undef CONFIG_CMD_NFS		/* NFS support			*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /*
  * TWL4030
diff --git a/include/configs/dnp5370.h b/include/configs/dnp5370.h
index f2f4102..d0e72e3 100644
--- a/include/configs/dnp5370.h
+++ b/include/configs/dnp5370.h
@@ -85,8 +85,8 @@
 
 #define ENV_IS_EMBEDDED
 #define LDS_BOARD_TEXT \
-	arch/blackfin/lib/libblackfin.o (.text*); \
-	arch/blackfin/cpu/libblackfin.o (.text*); \
+	arch/blackfin/lib/built-in.o (.text*); \
+	arch/blackfin/cpu/built-in.o (.text*); \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);
 
diff --git a/include/configs/ecovec.h b/include/configs/ecovec.h
index 335e9cd..3483cf1 100644
--- a/include/configs/ecovec.h
+++ b/include/configs/ecovec.h
@@ -58,18 +58,17 @@
 
 /* I2C */
 #define CONFIG_CMD_I2C
-#define CONFIG_SH_I2C 1
-#define CONFIG_HARD_I2C		1
-#define CONFIG_I2C_MULTI_BUS	1
-#define CONFIG_SYS_MAX_I2C_BUS	2
-#define CONFIG_SYS_I2C_MODULE	1
-#define CONFIG_SYS_I2C_SPEED	100000 /* 100 kHz */
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SH
 #define CONFIG_SYS_I2C_SLAVE	0x7F
+#define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS 2
+#define CONFIG_SYS_I2C_SH_BASE0	0xA4470000
+#define CONFIG_SYS_I2C_SH_SPEED0	100000
+#define CONFIG_SYS_I2C_SH_BASE1	0xA4750000
+#define CONFIG_SYS_I2C_SH_SPEED1	100000
 #define CONFIG_SH_I2C_DATA_HIGH	4
 #define CONFIG_SH_I2C_DATA_LOW 	5
 #define CONFIG_SH_I2C_CLOCK  	41666666
-#define CONFIG_SH_I2C_BASE0		0xA4470000
-#define CONFIG_SH_I2C_BASE1		0xA4750000
 
 /* Ether */
 #define CONFIG_SH_ETHER 1
diff --git a/include/configs/highbank.h b/include/configs/highbank.h
index b86eb43..7dbee3c 100644
--- a/include/configs/highbank.h
+++ b/include/configs/highbank.h
@@ -8,7 +8,6 @@
 #define __CONFIG_H
 
 #define CONFIG_SYS_DCACHE_OFF
-#define CONFIG_L2_OFF
 #define CONFIG_SYS_THUMB_BUILD
 
 #define CONFIG_SYS_NO_FLASH
diff --git a/include/configs/ibf-dsp561.h b/include/configs/ibf-dsp561.h
index 5291755..ac5ca9a 100644
--- a/include/configs/ibf-dsp561.h
+++ b/include/configs/ibf-dsp561.h
@@ -95,8 +95,8 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-	arch/blackfin/lib/libblackfin.o (.text*); \
-	arch/blackfin/cpu/libblackfin.o (.text*); \
+	arch/blackfin/lib/built-in.o (.text*); \
+	arch/blackfin/cpu/built-in.o (.text*); \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);
 #endif
diff --git a/include/configs/km/kmp204x-common.h b/include/configs/km/kmp204x-common.h
index 2d5320b..7700b38 100644
--- a/include/configs/km/kmp204x-common.h
+++ b/include/configs/km/kmp204x-common.h
@@ -111,7 +111,7 @@ unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
 
 #define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_FSL_DDR_INTERACTIVE
 
 #define CONFIG_SYS_SPD_BUS_NUM	0
diff --git a/include/configs/kzm9g.h b/include/configs/kzm9g.h
index 1afd487..f183279 100644
--- a/include/configs/kzm9g.h
+++ b/include/configs/kzm9g.h
@@ -22,7 +22,6 @@
 #define CONFIG_DISPLAY_CPUINFO
 #define CONFIG_DISPLAY_BOARDINFO
 #define CONFIG_BOARD_EARLY_INIT_F
-#define CONFIG_L2_OFF
 #define CONFIG_OF_LIBFDT
 
 #include <config_cmd_default.h>
@@ -139,21 +138,22 @@
 
 /* I2C */
 #define CONFIG_CMD_I2C
-#define CONFIG_SH_I2C 1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_SH
+#define CONFIG_SYS_I2C_SH_NUM_CONTROLLERS 5
+#define CONFIG_SYS_I2C_SH_BASE0	0xE6820000
+#define CONFIG_SYS_I2C_SH_SPEED0	100000
+#define CONFIG_SYS_I2C_SH_BASE1	0xE6822000
+#define CONFIG_SYS_I2C_SH_SPEED1	100000
+#define CONFIG_SYS_I2C_SH_BASE2	0xE6824000
+#define CONFIG_SYS_I2C_SH_SPEED2	100000
+#define CONFIG_SYS_I2C_SH_BASE3	0xE6826000
+#define CONFIG_SYS_I2C_SH_SPEED3	100000
+#define CONFIG_SYS_I2C_SH_BASE4	0xE6828000
+#define CONFIG_SYS_I2C_SH_SPEED4	100000
 #define CONFIG_SH_I2C_8BIT
-#define CONFIG_HARD_I2C
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_MAX_I2C_BUS  (5)
-#define CONFIG_SYS_I2C_MODULE
-#define CONFIG_SYS_I2C_SPEED    (100000) /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE    (0x7F)
-#define CONFIG_SH_I2C_DATA_HIGH (4)
-#define CONFIG_SH_I2C_DATA_LOW  (5)
-#define CONFIG_SH_I2C_CLOCK     (104000000) /* 104 MHz */
-#define CONFIG_SH_I2C_BASE0     (0xE6820000)
-#define CONFIG_SH_I2C_BASE1     (0xE6822000)
-#define CONFIG_SH_I2C_BASE2     (0xE6824000)
-#define CONFIG_SH_I2C_BASE3     (0xE6826000)
-#define CONFIG_SH_I2C_BASE4     (0xE6828000)
+#define CONFIG_SH_I2C_DATA_HIGH 4
+#define CONFIG_SH_I2C_DATA_LOW  5
+#define CONFIG_SH_I2C_CLOCK     104000000 /* 104 MHz */
 
 #endif /* __KZM9G_H */
diff --git a/include/configs/qemu-malta.h b/include/configs/malta.h
index 03514d1..cc574ed 100644
--- a/include/configs/qemu-malta.h
+++ b/include/configs/malta.h
@@ -4,8 +4,8 @@
  * SPDX-License-Identifier:	GPL-2.0
  */
 
-#ifndef _QEMU_MALTA_CONFIG_H
-#define _QEMU_MALTA_CONFIG_H
+#ifndef _MALTA_CONFIG_H
+#define _MALTA_CONFIG_H
 
 #include <asm/addrspace.h>
 #include <asm/malta.h>
@@ -13,12 +13,21 @@
 /*
  * System configuration
  */
-#define CONFIG_QEMU_MALTA
+#define CONFIG_MALTA
+
+#define CONFIG_MEMSIZE_IN_BYTES
 
 #define CONFIG_PCI
 #define CONFIG_PCI_GT64120
+#define CONFIG_PCI_MSC01
 #define CONFIG_PCI_PNP
 #define CONFIG_PCNET
+#define CONFIG_PCNET_79C973
+#define PCNET_HAS_PROM
+
+#define CONFIG_MISC_INIT_R
+#define CONFIG_RTC_MC146818
+#define CONFIG_SYS_ISA_IO_BASE_ADDRESS	0
 
 /*
  * CPU Configuration
@@ -26,17 +35,13 @@
 #define CONFIG_SYS_MHZ			250	/* arbitrary value */
 #define CONFIG_SYS_MIPS_TIMER_FREQ	(CONFIG_SYS_MHZ * 1000000)
 
-#define CONFIG_SYS_DCACHE_SIZE		16384	/* arbitrary value */
-#define CONFIG_SYS_ICACHE_SIZE		16384	/* arbitrary value */
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* arbitrary value */
-
 #define CONFIG_SWAP_IO_SPACE
 
 /*
  * Memory map
  */
-#define CONFIG_SYS_TEXT_BASE		0xbfc00000 /* Rom version */
-#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_TEXT_BASE		0xbe000000 /* Rom version */
+#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_TEXT_BASE
 
 #define CONFIG_SYS_SDRAM_BASE		0x80000000 /* Cached addr */
 #define CONFIG_SYS_MEM_SIZE		(256 * 1024 * 1024)
@@ -49,14 +54,15 @@
 
 #define CONFIG_SYS_MALLOC_LEN		(128 * 1024)
 #define CONFIG_SYS_BOOTPARAMS_LEN	(128 * 1024)
+#define CONFIG_SYS_BOOTM_LEN		(64 * 1024 * 1024)
 
 /*
  * Console configuration
  */
 #if defined(CONFIG_SYS_LITTLE_ENDIAN)
-#define CONFIG_SYS_PROMPT		"qemu-maltael # "
+#define CONFIG_SYS_PROMPT		"maltael # "
 #else
-#define CONFIG_SYS_PROMPT		"qemu-malta # "
+#define CONFIG_SYS_PROMPT		"malta # "
 #endif
 
 #define CONFIG_SYS_CBSIZE		256
@@ -75,17 +81,12 @@
 #define CONFIG_SYS_NS16550
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		115200
-#define CONFIG_SYS_NS16550_COM1		CKSEG1ADDR(MALTA_UART_BASE)
+#define CONFIG_SYS_NS16550_CLK		(115200 * 16)
+#define CONFIG_SYS_NS16550_COM1		CKSEG1ADDR(MALTA_GT_UART0_BASE)
+#define CONFIG_SYS_NS16550_COM2		CKSEG1ADDR(MALTA_MSC01_UART0_BASE)
 #define CONFIG_CONS_INDEX		1
 
 /*
- * Environment
- */
-#define CONFIG_ENV_IS_NOWHERE
-#define CONFIG_ENV_SIZE			0x10000
-
-/*
  * Flash configuration
  */
 #define CONFIG_SYS_FLASH_BASE		(KSEG1 | MALTA_FLASH_BASE)
@@ -96,6 +97,15 @@
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 
 /*
+ * Environment
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_SECT_SIZE		0x20000
+#define CONFIG_ENV_SIZE			CONFIG_ENV_SECT_SIZE
+#define CONFIG_ENV_ADDR \
+	(CONFIG_SYS_FLASH_BASE + (4 << 20) - CONFIG_ENV_SIZE)
+
+/*
  * Commands
  */
 #include <config_cmd_default.h>
@@ -105,9 +115,11 @@
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_NFS
 
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_PCI
 #define CONFIG_CMD_PING
 
 #define CONFIG_SYS_LONGHELP		/* verbose help, undef to save memory */
 
-#endif /* _QEMU_MALTA_CONFIG_H */
+#endif /* _MALTA_CONFIG_H */
diff --git a/include/configs/mcx.h b/include/configs/mcx.h
index 4619dfb..dcd29ce 100644
--- a/include/configs/mcx.h
+++ b/include/configs/mcx.h
@@ -137,10 +137,10 @@
 #undef CONFIG_CMD_IMLS		/* List all found images	*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /* RTC */
 #define CONFIG_RTC_DS1337
@@ -353,7 +353,6 @@
 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_NAND_SOFTECC
 
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBDISK_SUPPORT
@@ -395,6 +394,7 @@
 					 56, 57, 58, 59, 60, 61, 62, 63}
 #define CONFIG_SYS_NAND_ECCSIZE		256
 #define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_SW
 
 #define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE
 
diff --git a/include/configs/mpq101.h b/include/configs/mpq101.h
index 6d0d392..ec09e15 100644
--- a/include/configs/mpq101.h
+++ b/include/configs/mpq101.h
@@ -52,7 +52,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 
 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
 
diff --git a/include/configs/mx51_efikamx.h b/include/configs/mx51_efikamx.h
index 8a44ef5..0f2a4ef 100644
--- a/include/configs/mx51_efikamx.h
+++ b/include/configs/mx51_efikamx.h
@@ -29,7 +29,6 @@
 
 #define CONFIG_SYS_TEXT_BASE		0x97800000
 
-#define	CONFIG_L2_OFF
 #define	CONFIG_SYS_ICACHE_OFF
 #define	CONFIG_SYS_DCACHE_OFF
 
diff --git a/include/configs/nokia_rx51.h b/include/configs/nokia_rx51.h
index 4332779..e0c0fac 100644
--- a/include/configs/nokia_rx51.h
+++ b/include/configs/nokia_rx51.h
@@ -157,10 +157,10 @@
 #undef CONFIG_CMD_SETGETDCR		/* DCR support on 4xx */
 
 #define CONFIG_OMAP3_SPI
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /*
  * TWL4030
diff --git a/include/configs/omap3_beagle.h b/include/configs/omap3_beagle.h
index c662cc0..3acb854 100644
--- a/include/configs/omap3_beagle.h
+++ b/include/configs/omap3_beagle.h
@@ -158,11 +158,10 @@
 #undef CONFIG_CMD_IMLS		/* List all found images	*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C			1
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_I2C_MULTI_BUS		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_VIDEO_OMAP3	/* DSS Support			*/
 
 /*
@@ -429,6 +428,7 @@
 						10, 11, 12, 13}
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
 
diff --git a/include/configs/omap3_evm.h b/include/configs/omap3_evm.h
index 3ace8bb..b7638fb 100644
--- a/include/configs/omap3_evm.h
+++ b/include/configs/omap3_evm.h
@@ -107,6 +107,7 @@
 						10, 11, 12, 13}
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW
 #define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
 
diff --git a/include/configs/omap3_evm_common.h b/include/configs/omap3_evm_common.h
index 3eae288..43616e2 100644
--- a/include/configs/omap3_evm_common.h
+++ b/include/configs/omap3_evm_common.h
@@ -87,11 +87,10 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C
-#define CONFIG_DRIVER_OMAP34XX_I2C
-
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /*
  * PISMO support
diff --git a/include/configs/omap3_evm_quick_nand.h b/include/configs/omap3_evm_quick_nand.h
index 9ecd70d..4427e88 100644
--- a/include/configs/omap3_evm_quick_nand.h
+++ b/include/configs/omap3_evm_quick_nand.h
@@ -86,6 +86,7 @@
 						10, 11, 12, 13}
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW
 #define CONFIG_SYS_NAND_U_BOOT_START   CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
 
diff --git a/include/configs/omap3_igep00x0.h b/include/configs/omap3_igep00x0.h
index ac36ac6..71062a6 100644
--- a/include/configs/omap3_igep00x0.h
+++ b/include/configs/omap3_igep00x0.h
@@ -124,10 +124,10 @@
 #undef CONFIG_CMD_IMLS		/* List all found images	*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C			1
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_OMAP34XX
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
 
 /*
  * TWL4030
@@ -362,6 +362,7 @@
 						10, 11, 12, 13}
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
 #endif
diff --git a/include/configs/omap3_logic.h b/include/configs/omap3_logic.h
index 0c096f4..bedd6f9 100644
--- a/include/configs/omap3_logic.h
+++ b/include/configs/omap3_logic.h
@@ -118,12 +118,10 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C
-#define CONFIG_DRIVER_OMAP34XX_I2C
-
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /*
  * TWL4030
diff --git a/include/configs/omap3_mvblx.h b/include/configs/omap3_mvblx.h
index 45da2e0..8d11010 100644
--- a/include/configs/omap3_mvblx.h
+++ b/include/configs/omap3_mvblx.h
@@ -128,11 +128,10 @@
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_FPGA
 
-#define CONFIG_HARD_I2C			1
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		0
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
-#define CONFIG_I2C_MULTI_BUS		1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /*
  * TWL4030
diff --git a/include/configs/omap3_overo.h b/include/configs/omap3_overo.h
index 4641694..e0f0262 100644
--- a/include/configs/omap3_overo.h
+++ b/include/configs/omap3_overo.h
@@ -98,11 +98,10 @@
 #define CONFIG_CMD_NET		/* bootp, tftpboot, rarpboot	*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_DRIVER_OMAP34XX_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /*
  * TWL4030
@@ -325,6 +324,7 @@
 						10, 11, 12, 13}
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
 
diff --git a/include/configs/omap3_pandora.h b/include/configs/omap3_pandora.h
index 3cce0de..eacdfaa 100644
--- a/include/configs/omap3_pandora.h
+++ b/include/configs/omap3_pandora.h
@@ -111,10 +111,10 @@
 #undef CONFIG_CMD_NFS		/* NFS support			*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C			1
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /*
  * TWL4030
diff --git a/include/configs/omap3_sdp3430.h b/include/configs/omap3_sdp3430.h
index 697a3f3..6f1304d 100644
--- a/include/configs/omap3_sdp3430.h
+++ b/include/configs/omap3_sdp3430.h
@@ -114,10 +114,10 @@
 /*
  * I2C for power management setup
  */
-#define CONFIG_HARD_I2C			1
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /* OMITTED:  single 1 Gbit MT29F1G NAND flash */
 
diff --git a/include/configs/omap3_zoom1.h b/include/configs/omap3_zoom1.h
index 8591f98..1dd53fa 100644
--- a/include/configs/omap3_zoom1.h
+++ b/include/configs/omap3_zoom1.h
@@ -118,10 +118,10 @@
 #undef CONFIG_CMD_NFS		/* NFS support			*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C			1
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /*
  * TWL4030
diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h
index cb8c7ec..f749740 100644
--- a/include/configs/omap3_zoom2.h
+++ b/include/configs/omap3_zoom2.h
@@ -138,10 +138,10 @@
 #undef CONFIG_CMD_NFS			/* NFS support			*/
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C			1
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 
 /*
  * TWL4030
diff --git a/include/configs/origen.h b/include/configs/origen.h
index bad34b3..f46b833 100644
--- a/include/configs/origen.h
+++ b/include/configs/origen.h
@@ -22,8 +22,6 @@
 #define CONFIG_DISPLAY_BOARDINFO
 #define CONFIG_BOARD_EARLY_INIT_F
 
-/* Keep L2 Cache Disabled */
-#define CONFIG_L2_OFF			1
 #define CONFIG_SYS_DCACHE_OFF		1
 
 #define CONFIG_SYS_SDRAM_BASE		0x40000000
diff --git a/include/configs/p1_p2_rdb_pc.h b/include/configs/p1_p2_rdb_pc.h
index 91a6782..57ed019 100644
--- a/include/configs/p1_p2_rdb_pc.h
+++ b/include/configs/p1_p2_rdb_pc.h
@@ -325,7 +325,7 @@
 #endif
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_SYS_DDR_RAW_TIMING
 #define CONFIG_DDR_SPD
 #define CONFIG_SYS_SPD_BUS_NUM 1
diff --git a/include/configs/p1_twr.h b/include/configs/p1_twr.h
index 76189e1..9837100 100644
--- a/include/configs/p1_twr.h
+++ b/include/configs/p1_twr.h
@@ -89,7 +89,7 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 
 #define CONFIG_SYS_SDRAM_SIZE_LAW	LAW_SIZE_512M
 #define CONFIG_CHIP_SELECTS_PER_CTRL	1
diff --git a/include/configs/pcm051.h b/include/configs/pcm051.h
index 4970b13..6f41ee7 100644
--- a/include/configs/pcm051.h
+++ b/include/configs/pcm051.h
@@ -172,11 +172,10 @@
 /* I2C Configuration */
 #define CONFIG_I2C
 #define CONFIG_CMD_I2C
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_DRIVER_OMAP24XX_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP24XX
 #define CONFIG_CMD_EEPROM
 #define CONFIG_ENV_EEPROM_IS_ON_I2C
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* Main EEPROM */
diff --git a/include/configs/sandbox.h b/include/configs/sandbox.h
index 0884ad3..a4edc62 100644
--- a/include/configs/sandbox.h
+++ b/include/configs/sandbox.h
@@ -75,7 +75,6 @@
 #define CONFIG_SYS_LOAD_ADDR		0x00000000
 #define CONFIG_SYS_MEMTEST_START	0x00100000
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 0x1000)
-#define CONFIG_PHYS_64BIT
 #define CONFIG_SYS_FDT_LOAD_ADDR	0x1000000
 
 /* Size of our emulated memory */
diff --git a/include/configs/sbc8548.h b/include/configs/sbc8548.h
index 6d97060..bdb8eb5 100644
--- a/include/configs/sbc8548.h
+++ b/include/configs/sbc8548.h
@@ -102,7 +102,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #undef CONFIG_DDR_ECC			/* only for ECC DDR module */
 /*
diff --git a/include/configs/siemens-am33x-common.h b/include/configs/siemens-am33x-common.h
index 7db0eb8..4569fd4 100644
--- a/include/configs/siemens-am33x-common.h
+++ b/include/configs/siemens-am33x-common.h
@@ -131,11 +131,10 @@
 /* I2C Configuration */
 #define CONFIG_I2C
 #define CONFIG_CMD_I2C
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_DRIVER_OMAP24XX_I2C
-
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	OMAP_I2C_STANDARD
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP24XX
 
 /* Defines for SPL */
 #define CONFIG_SPL
@@ -196,6 +195,7 @@
 
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	14
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_BCH8_CODE_HW
 
 #define CONFIG_SYS_NAND_ECCSTEPS	4
 #define	CONFIG_SYS_NAND_ECCTOTAL	(CONFIG_SYS_NAND_ECCBYTES * \
@@ -456,6 +456,7 @@
 		"\0"
 
 #define CONFIG_NAND_OMAP_GPMC
+#define CONFIG_NAND_OMAP_ELM
 #define GPMC_NAND_ECC_LP_x16_LAYOUT	1
 #define CONFIG_SYS_NAND_BASE		(0x08000000)	/* physical address */
 							/* to access nand at */
diff --git a/include/configs/smdkv310.h b/include/configs/smdkv310.h
index e2e8efe..1388f49 100644
--- a/include/configs/smdkv310.h
+++ b/include/configs/smdkv310.h
@@ -25,9 +25,6 @@
 /* Mach Type */
 #define CONFIG_MACH_TYPE		MACH_TYPE_SMDKV310
 
-/* Keep L2 Cache Disabled */
-#define CONFIG_L2_OFF			1
-
 #define CONFIG_SYS_SDRAM_BASE		0x40000000
 #define CONFIG_SYS_TEXT_BASE		0x43E00000
 
diff --git a/include/configs/snowball.h b/include/configs/snowball.h
index 00d6fa5..9a069f3 100644
--- a/include/configs/snowball.h
+++ b/include/configs/snowball.h
@@ -23,7 +23,6 @@
  * (easy to change)
  */
 #define CONFIG_U8500
-#define CONFIG_L2_OFF
 
 #define CONFIG_SYS_MEMTEST_START	0x00000000
 #define CONFIG_SYS_MEMTEST_END	0x1FFFFFFF
diff --git a/include/configs/socfpga_cyclone5.h b/include/configs/socfpga_cyclone5.h
index 980636c..608578a 100644
--- a/include/configs/socfpga_cyclone5.h
+++ b/include/configs/socfpga_cyclone5.h
@@ -16,7 +16,6 @@
 #define CONFIG_SOCFPGA_VIRTUAL_TARGET
 
 #define CONFIG_ARMV7
-#define CONFIG_L2_OFF
 #define CONFIG_SYS_DCACHE_OFF
 #undef CONFIG_USE_IRQ
 
diff --git a/include/configs/socrates.h b/include/configs/socrates.h
index b6fbe23..0e6b864 100644
--- a/include/configs/socrates.h
+++ b/include/configs/socrates.h
@@ -80,7 +80,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
diff --git a/include/configs/spieval.h b/include/configs/spieval.h
deleted file mode 100644
index 07668de..0000000
--- a/include/configs/spieval.h
+++ /dev/null
@@ -1,494 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2004-2005
- * Martin Krause, TQ-Systems GmbH, martin.krause@tqs.de
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-
-#define CONFIG_MPC5xxx		1	/* This is an MPC5xxx CPU */
-#define CONFIG_MPC5200		1	/* (more precisely an MPC5200 CPU) */
-#define CONFIG_TQM5200		1	/* ... on TQM5200 module */
-#undef CONFIG_TQM5200_REV100		/*  define for revision 100 modules */
-#define CONFIG_STK52XX		1	/* ... on a STK52XX base board */
-#define CONFIG_STK52XX_REV100	1	/*  define for revision 100 baseboards */
-
-#define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */
-
-#define CONFIG_HIGH_BATS	1	/* High BATs supported */
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE	6	/* console is on PSC6 */
-#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }
-
-#ifdef CONFIG_STK52XX
-#undef CONFIG_PS2KBD			/* AT-PS/2 Keyboard		*/
-#define CONFIG_PS2MULT			/* .. on PS/2 Multiplexer	*/
-#define CONFIG_PS2SERIAL	6	/* .. on PSC6			*/
-#define CONFIG_PS2MULT_DELAY	(CONFIG_SYS_HZ/2)	/* Initial delay	*/
-#define CONFIG_BOARD_EARLY_INIT_R
-#endif /* CONFIG_STK52XX */
-
-/*
- * PCI Mapping:
- * 0x40000000 - 0x4fffffff - PCI Memory
- * 0x50000000 - 0x50ffffff - PCI IO Space
- */
-#ifdef CONFIG_STK52XX
-#define CONFIG_PCI		1
-#define CONFIG_PCI_PNP		1
-/* #define CONFIG_PCI_SCAN_SHOW	1 */
-
-#define CONFIG_PCI_MEM_BUS	0x40000000
-#define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
-#define CONFIG_PCI_MEM_SIZE	0x10000000
-
-#define CONFIG_PCI_IO_BUS	0x50000000
-#define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
-#define CONFIG_PCI_IO_SIZE	0x01000000
-
-#define CONFIG_EEPRO100		1
-#define CONFIG_SYS_RX_ETH_BUFFER	8  /* use 8 rx buffer on eepro100  */
-#define CONFIG_NS8382X		1
-#endif	/* CONFIG_STK52XX */
-
-/*
- * Video console
- */
-#if 1
-#define CONFIG_VIDEO
-#define CONFIG_VIDEO_SM501
-#define CONFIG_VIDEO_SM501_32BPP
-#define CONFIG_CFB_CONSOLE
-#define CONFIG_VIDEO_LOGO
-#define CONFIG_VGA_AS_SINGLE_DEVICE
-#define CONFIG_CONSOLE_EXTRA_INFO
-#define CONFIG_VIDEO_SW_CURSOR
-#define CONFIG_SPLASH_SCREEN
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-#endif
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
-/* USB */
-#ifdef CONFIG_STK52XX
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-#endif
-
-/* POST support */
-#define CONFIG_POST		(CONFIG_SYS_POST_MEMORY   | \
-				 CONFIG_SYS_POST_CPU	   | \
-				 CONFIG_SYS_POST_I2C)
-
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define MPC5XXX_SRAM_POST_SIZE MPC5XXX_SRAM_SIZE-4
-#endif
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ECHO
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SNTP
-
-#if defined(CONFIG_MINIFAP) || defined(CONFIG_STK52XX)
-    #define CONFIG_CMD_IDE
-    #define CONFIG_CMD_FAT
-    #define CONFIG_CMD_EXT2
-#endif
-
-#ifdef CONFIG_STK52XX
-    #define CONFIG_CMD_USB
-    #define CONFIG_CMD_FAT
-#endif
-
-#ifdef CONFIG_VIDEO
-    #define CONFIG_CMD_BMP
-#endif
-
-#ifdef CONFIG_PCI
-    #define CONFIG_CMD_PCI
-    #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1
-#endif
-
-#ifdef CONFIG_POST
-#define CONFIG_CMD_DIAG
-#endif
-
-
-#define	CONFIG_TIMESTAMP		/* display image timestamps */
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFC000000)		/* Boot low */
-#   define CONFIG_SYS_LOWBOOT		1
-#endif
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
-
-#define CONFIG_PREBOOT	"echo;" \
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"rootpath=/opt/eldk/ppc_6xx\0"					\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"flash_self=run ramargs addip;"					\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"flash_nfs=run nfsargs addip;"					\
-		"bootm ${kernel_addr}\0"				\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
-	"bootfile=/tftpboot/tqm5200/uImage\0"				\
-	"load=tftp 200000 ${u-boot}\0"					\
-	"u-boot=/tftpboot/tqm5200/u-boot.bin\0"				\
-	"update=protect off FC000000 FC05FFFF;"				\
-		"erase FC000000 FC05FFFF;"				\
-		"cp.b 200000 FC000000 ${filesize};"			\
-		"protect on FC000000 FC05FFFF\0"			\
-	""
-
-#define CONFIG_BOOTCOMMAND	"run net_nfs"
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK		/* define for 133MHz speed */
-
-#if defined(CONFIG_SYS_IPBCLK_EQUALS_XLBCLK)
-/*
- * PCI Bus clocking configuration
- *
- * Actually a PCI Clock of 66 MHz is only set (in cpu_init.c) if
- * CONFIG_SYS_IPBCLK_EQUALS_XLBCLK is defined. This is because a PCI Clock
- * of 66 MHz yet hasn't been tested with a IPB Bus Clock of 66 MHz.
- */
-#define CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2	/* define for 66MHz speed */
-#endif
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support */
-#ifdef CONFIG_TQM5200_REV100
-#define CONFIG_SYS_I2C_MODULE		1	/* Select I2C module #1 for rev. 100 board */
-#else
-#define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #2 for all other revs */
-#endif
-
-/*
- * I2C clock frequency
- *
- * Please notice, that the resulting clock frequency could differ from the
- * configured value. This is because the I2C clock is derived from system
- * clock over a frequency divider with only a few divider values. U-boot
- * calculates the best approximation for CONFIG_SYS_I2C_SPEED. However the calculated
- * approximation allways lies below the configured value, never above.
- */
-#define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE		0x7F
-
-/*
- * EEPROM configuration for onboard EEPROM M24C32 (M24C64 should work
- * also). For other EEPROMs configuration should be verified. On Mini-FAP the
- * EEPROM (24C64) is on the same I2C address (but on other I2C bus), so the
- * same configuration could be used.
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* =32 Bytes per write */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	20
-
-/*
- * HW-Monitor configuration on Mini-FAP
- */
-#if defined (CONFIG_MINIFAP)
-#define CONFIG_SYS_I2C_HWMON_ADDR		0x2C
-#endif
-
-/* List of I2C addresses to be verified by POST */
-#if defined (CONFIG_MINIFAP)
-#undef CONFIG_SYS_POST_I2C_ADDRS
-#define CONFIG_SYS_POST_I2C_ADDRS	{CONFIG_SYS_I2C_EEPROM_ADDR,	\
-					 CONFIG_SYS_I2C_HWMON_ADDR,	\
-					 CONFIG_SYS_I2C_SLAVE}
-#endif
-
-/*
- * Flash configuration
- */
-#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_TEXT_BASE /* 0xFC000000 */
-
-/* use CFI flash driver if no module variant is spezified */
-#define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_BOOTCS_START }
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_SIZE		0x04000000 /* 64 MByte */
-#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max num of sects on one chip */
-#undef CONFIG_SYS_FLASH_USE_BUFFER_WRITE	/* not supported yet for AMD */
-
-#if !defined(CONFIG_SYS_LOWBOOT)
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00760000 + 0x00800000)
-#else	/* CONFIG_SYS_LOWBOOT */
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x00060000)
-#endif	/* CONFIG_SYS_LOWBOOT */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks
-					   (= chip selects) */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
-
-
-/*
- * Environment settings
- */
-#define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_SIZE		0x10000
-#define CONFIG_ENV_SECT_SIZE	0x20000
-#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
-#define	CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR		0xF0000000
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR	0x80000000
-
-/* Use ON-Chip SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
-#ifdef CONFIG_POST
-/* preserve space for the post_word at end of on-chip SRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_POST_SIZE
-#else
-#define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE
-#endif
-
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#   define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN		(384 << 10)	/* Reserve 384 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC	1
-/*
- * Define CONFIG_FEC_10MBIT to force FEC at 10Mb
- */
-/* #define CONFIG_FEC_10MBIT 1 */
-#define CONFIG_PHY_ADDR		0x00
-
-/*
- * GPIO configuration
- *
- * use pin gpio_wkup_6 as second SDRAM chip select (mem_cs1):
- *	Bit 0 (mask: 0x80000000): 1
- * use ALT CAN position: Bits 2-3 (mask: 0x30000000):
- *	00 -> No Alternatives, CAN1/2 on PSC2 according to PSC2 setting.
- *	01 -> CAN1 on I2C1, CAN2 on Tmr0/1.
- *	      Use for REV200 STK52XX boards. Do not use with REV100 modules
- *	      (because, there I2C1 is used as I2C bus)
- * use PSC1 as UART: Bits 28-31 (mask: 0x00000007): 0100
- * use PSC2 as CAN: Bits 25:27 (mask: 0x00000030)
- *	000 -> All PSC2 pins are GIOPs
- *	001 -> CAN1/2 on PSC2 pins
- *	       Use for REV100 STK52xx boards
- * use PSC6:
- *   on STK52xx:
- *	use as UART. Pins PSC6_0 to PSC6_3 are used.
- *	Bits 9:11 (mask: 0x00700000):
- *	   101 -> PSC6 : Extended POST test is not available
- *   on MINI-FAP and TQM5200_IB:
- *	use PSC6_0 to PSC6_3 as GPIO: Bits 9:11 (mask: 0x00700000):
- *	   000 -> PSC6 could not be used as UART, CODEC or IrDA
- *   GPIO on PSC6_3 is used in post_hotkeys_pressed() to enable extended POST
- *   tests.
- */
-#if defined (CONFIG_MINIFAP)
-# define CONFIG_SYS_GPS_PORT_CONFIG	0x91000004
-#elif defined (CONFIG_STK52XX)
-# if defined (CONFIG_STK52XX_REV100)
-#  define CONFIG_SYS_GPS_PORT_CONFIG	0x81500014
-# else /* STK52xx REV200 and above */
-#  if defined (CONFIG_TQM5200_REV100)
-#   error TQM5200 REV100 not supported on STK52XX REV200 or above
-#  else/* TQM5200 REV200 and above */
-#   define CONFIG_SYS_GPS_PORT_CONFIG	0x91500004
-#  endif
-# endif
-#else  /* TMQ5200 Inbetriebnahme-Board */
-# define CONFIG_SYS_GPS_PORT_CONFIG	0x81000004
-#endif
-
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_MPC5200	1	/* use internal MPC5200 RTC */
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
-#else
-#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-/* Enable an alternate, more extensive memory test */
-#define CONFIG_SYS_ALT_MEMTEST
-
-#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-
-#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
-#endif
-
-/*
- * Enable loopw command.
- */
-#define CONFIG_LOOPW
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL		HID0_ICE
-
-#define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
-#ifdef CONFIG_SYS_PCICLK_EQUALS_IPBCLK_DIV2
-#define CONFIG_SYS_BOOTCS_CFG		0x0008DF30 /* for pci_clk  = 66 MHz */
-#else
-#define CONFIG_SYS_BOOTCS_CFG		0x0004DF30 /* for pci_clk = 33 MHz */
-#endif
-#define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_LAST_STAGE_INIT
-
-/*
- * SRAM - Do not map below 2 GB in address space, because this area is used
- * for SDRAM autosizing.
- */
-#define CONFIG_SYS_CS2_START		0xE5000000
-#define CONFIG_SYS_CS2_SIZE		0x100000	/* 1 MByte */
-#define CONFIG_SYS_CS2_CFG		0x0004D930
-
-/*
- * Grafic controller - Do not map below 2 GB in address space, because this
- * area is used for SDRAM autosizing.
- */
-#define SM501_FB_BASE		0xE0000000
-#define CONFIG_SYS_CS1_START		(SM501_FB_BASE)
-#define CONFIG_SYS_CS1_SIZE		0x4000000	/* 64 MByte */
-#define CONFIG_SYS_CS1_CFG		0x8F48FF70
-#define SM501_MMIO_BASE		CONFIG_SYS_CS1_START + 0x03E00000
-
-#define CONFIG_SYS_CS_BURST		0x00000000
-#define CONFIG_SYS_CS_DEADCYCLE	0x33333311	/* 1 dead cycle for flash and SM501 */
-
-#define CONFIG_SYS_RESET_ADDRESS	0xff000000
-
-/*-----------------------------------------------------------------------
- * USB stuff
- *-----------------------------------------------------------------------
- */
-#define CONFIG_USB_CLOCK	0x0001BBBB
-#define CONFIG_USB_CONFIG	0x00001000
-
-/*-----------------------------------------------------------------------
- * IDE/ATA stuff Supports IDE harddisk
- *-----------------------------------------------------------------------
- */
-
-#undef	CONFIG_IDE_8xx_PCCARD		/* Use IDE with PC Card Adapter */
-
-#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE	 not supported	*/
-#undef	CONFIG_IDE_LED			/* LED	 for ide not supported	*/
-
-#define CONFIG_IDE_RESET		/* reset for ide supported	*/
-#define CONFIG_IDE_PREINIT
-
-#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
-#define CONFIG_SYS_IDE_MAXDEVICE	2	/* max. 2 drives per IDE bus	*/
-
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-
-#define CONFIG_SYS_ATA_BASE_ADDR	MPC5XXX_ATA
-
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0060)
-
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(CONFIG_SYS_ATA_DATA_OFFSET)
-
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	(0x005C)
-
-/* Interval between registers						     */
-#define CONFIG_SYS_ATA_STRIDE		4
-
-#endif /* __CONFIG_H */
diff --git a/include/configs/stxgp3.h b/include/configs/stxgp3.h
index 9b3f0cc..ee1f1f3 100644
--- a/include/configs/stxgp3.h
+++ b/include/configs/stxgp3.h
@@ -98,7 +98,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
diff --git a/include/configs/stxssa.h b/include/configs/stxssa.h
index 805814f..63dd767 100644
--- a/include/configs/stxssa.h
+++ b/include/configs/stxssa.h
@@ -112,7 +112,7 @@
 #define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
 
 /* DDR Setup */
-#define CONFIG_FSL_DDR1
+#define CONFIG_SYS_FSL_DDR1
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup*/
 #define CONFIG_DDR_SPD
 #undef CONFIG_FSL_DDR_INTERACTIVE
diff --git a/include/configs/t4qds.h b/include/configs/t4qds.h
index 3f54f14..d9b0ed0 100644
--- a/include/configs/t4qds.h
+++ b/include/configs/t4qds.h
@@ -87,7 +87,7 @@
 #define CONFIG_FSL_DDR_FIRST_SLOT_QUAD_CAPABLE
 
 #define CONFIG_DDR_SPD
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 
 
 /*
diff --git a/include/configs/tam3517-common.h b/include/configs/tam3517-common.h
index 683bc54..439fc47 100644
--- a/include/configs/tam3517-common.h
+++ b/include/configs/tam3517-common.h
@@ -117,14 +117,13 @@
 #undef CONFIG_CMD_IMLS
 
 #define CONFIG_SYS_NO_FLASH
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		400000
-#define CONFIG_SYS_I2C_SLAVE		1
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	400000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
 #define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* base address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1		/* bytes of address */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07
-#define CONFIG_DRIVER_OMAP34XX_I2C
-
 
 /*
  * Board NAND Info.
@@ -225,7 +224,6 @@
 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_CONSOLE
 #define CONFIG_SPL_NAND_SIMPLE
-#define CONFIG_SPL_NAND_SOFTECC
 #define CONFIG_SPL_NAND_WORKSPACE	0x8f07f000 /* below BSS */
 
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
@@ -262,6 +260,7 @@
 					 56, 57, 58, 59, 60, 61, 62, 63}
 #define CONFIG_SYS_NAND_ECCSIZE		256
 #define CONFIG_SYS_NAND_ECCBYTES	3
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_SW
 
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 
@@ -369,7 +368,7 @@ struct tam3517_module_info {
 
 #define TAM3517_READ_EEPROM(info, ret) \
 do {								\
-	i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);	\
+	i2c_init(CONFIG_SYS_OMAP24_I2C_SPEED, CONFIG_SYS_OMAP24_I2C_SLAVE); \
 	if (eeprom_read(CONFIG_SYS_I2C_EEPROM_ADDR, 0,		\
 		(void *)info, sizeof(*info)))			\
 		ret = 1;					\
diff --git a/include/configs/tcm-bf537.h b/include/configs/tcm-bf537.h
index 2adb071..627836a 100644
--- a/include/configs/tcm-bf537.h
+++ b/include/configs/tcm-bf537.h
@@ -112,8 +112,8 @@
  * it linked after the configuration sector.
  */
 # define LDS_BOARD_TEXT \
-	arch/blackfin/lib/libblackfin.o (.text*); \
-	arch/blackfin/cpu/libblackfin.o (.text*); \
+	arch/blackfin/lib/built-in.o (.text*); \
+	arch/blackfin/cpu/built-in.o (.text*); \
 	. = DEFINED(env_offset) ? env_offset : .; \
 	common/env_embedded.o (.text*);
 #endif
diff --git a/include/configs/ti_armv7_common.h b/include/configs/ti_armv7_common.h
index 84269ad..99b60fc 100644
--- a/include/configs/ti_armv7_common.h
+++ b/include/configs/ti_armv7_common.h
@@ -59,12 +59,11 @@
 
 /* I2C IP block */
 #define CONFIG_I2C
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_DRIVER_OMAP24XX_I2C
 #define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP24XX
 
 /* MMC/SD IP block */
 #define CONFIG_MMC
diff --git a/include/configs/tricorder.h b/include/configs/tricorder.h
index d57394e..cc4001f 100644
--- a/include/configs/tricorder.h
+++ b/include/configs/tricorder.h
@@ -98,11 +98,11 @@
 #define CONFIG_DOS_PARTITION
 
 /* I2C */
-#define CONFIG_HARD_I2C
-#define CONFIG_SYS_I2C_SPEED		100000
-#define CONFIG_SYS_I2C_SLAVE		1
-#define CONFIG_DRIVER_OMAP34XX_I2C	1
-#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_OMAP24_I2C_SPEED	100000
+#define CONFIG_SYS_OMAP24_I2C_SLAVE	1
+#define CONFIG_SYS_I2C_OMAP34XX
+ 
 
 /* EEPROM */
 #define CONFIG_SYS_I2C_MULTI_EEPROMS
@@ -138,8 +138,9 @@
 
 #define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of NAND */
 							/* devices */
-#define CONFIG_NAND_OMAP_BCH8
 #define CONFIG_BCH
+#define CONFIG_SYS_NAND_MAX_OOBFREE	2
+#define CONFIG_SYS_NAND_MAX_ECCPOS	56
 
 /* commands to include */
 #include <config_cmd_default.h>
@@ -374,6 +375,7 @@
 
 #define CONFIG_SYS_NAND_ECCSIZE		512
 #define CONFIG_SYS_NAND_ECCBYTES	13
+#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
 
 #define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_TEXT_BASE
 
diff --git a/include/configs/u8500_href.h b/include/configs/u8500_href.h
index 45d33a6..629299d 100644
--- a/include/configs/u8500_href.h
+++ b/include/configs/u8500_href.h
@@ -12,7 +12,6 @@
  * (easy to change)
  */
 #define CONFIG_U8500
-#define CONFIG_L2_OFF
 
 #define CONFIG_SYS_MEMTEST_START	0x00000000
 #define CONFIG_SYS_MEMTEST_END	0x1FFFFFFF
diff --git a/include/configs/xpedite517x.h b/include/configs/xpedite517x.h
index 4738c23..88d7f88 100644
--- a/include/configs/xpedite517x.h
+++ b/include/configs/xpedite517x.h
@@ -40,7 +40,7 @@
 /*
  * DDR config
  */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
diff --git a/include/configs/xpedite520x.h b/include/configs/xpedite520x.h
index 3342880..f39d6f9 100644
--- a/include/configs/xpedite520x.h
+++ b/include/configs/xpedite520x.h
@@ -39,7 +39,7 @@
 /*
  * DDR config
  */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
diff --git a/include/configs/xpedite537x.h b/include/configs/xpedite537x.h
index 9da845d..e1bdf90 100644
--- a/include/configs/xpedite537x.h
+++ b/include/configs/xpedite537x.h
@@ -49,7 +49,7 @@
 /*
  * DDR config
  */
-#define CONFIG_FSL_DDR2
+#define CONFIG_SYS_FSL_DDR2
 #undef CONFIG_FSL_DDR_INTERACTIVE
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
diff --git a/include/configs/xpedite550x.h b/include/configs/xpedite550x.h
index 4137cc9..2328c7a 100644
--- a/include/configs/xpedite550x.h
+++ b/include/configs/xpedite550x.h
@@ -49,7 +49,7 @@
 /*
  * DDR config
  */
-#define CONFIG_FSL_DDR3
+#define CONFIG_SYS_FSL_DDR3
 #define CONFIG_SPD_EEPROM		/* Use SPD EEPROM for DDR setup */
 #define CONFIG_DDR_SPD
 #define CONFIG_MEM_INIT_VALUE		0xdeadbeef
diff --git a/include/configs/zynq.h b/include/configs/zynq.h
index 4c6e6e8..82ec826 100644
--- a/include/configs/zynq.h
+++ b/include/configs/zynq.h
@@ -60,10 +60,10 @@
 /* I2C */
 #if defined(CONFIG_ZYNQ_I2C0) || defined(CONFIG_ZYNQ_I2C1)
 # define CONFIG_CMD_I2C
-# define CONFIG_ZYNQ_I2C
-# define CONFIG_HARD_I2C
-# define CONFIG_SYS_I2C_SPEED		100000
-# define CONFIG_SYS_I2C_SLAVE		1
+# define CONFIG_SYS_I2C
+# define CONFIG_SYS_I2C_ZYNQ
+# define CONFIG_SYS_I2C_ZYNQ_SPEED		100000
+# define CONFIG_SYS_I2C_ZYNQ_SLAVE		1
 #endif
 
 #if defined(CONFIG_ZYNQ_DCC)
author	Albert ARIBAUD <albert.u.boot@aribaud.net>	2013-12-10 14:31:56 +0100
committer	Albert ARIBAUD <albert.u.boot@aribaud.net>	2013-12-10 22:23:59 +0100
commit	f15ea6e1d67782a1626d4a4922b6c20e380085e5 (patch)
tree	57d78f1ee94a2060eaa591533278d2934d4f1da3 /include/configs
parent	cb7ee1b98cac6baf244daefb1192adf5a47bc983 (diff)
parent	f44483b57c49282299da0e5c10073b909cdad979 (diff)
download	u-boot-imx-f15ea6e1d67782a1626d4a4922b6c20e380085e5.zip u-boot-imx-f15ea6e1d67782a1626d4a4922b6c20e380085e5.tar.gz u-boot-imx-f15ea6e1d67782a1626d4a4922b6c20e380085e5.tar.bz2