mpc83xx: add ids8313 support

add support for the ids8313 board.

CPU:   e300c3, MPC8313, Rev: 2.1 at 396 MHz, CSB: 132 MHz
I2C:   ready
SPI:   ready
DRAM:  128 MiB (DDR2, 32-bit, ECC off, 264 MHz)
Flash: 8 MiB
NAND:  128 MiB
Net:   TSEC0, TSEC1 [PRIME]

public key on NOR flash start

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>

1 files changed, 587 insertions, 0 deletions

diff --git a/include/configs/ids8313.h b/include/configs/ids8313.h
new file mode 100644
index 0000000..613f7e1
--- /dev/null
+++ b/include/configs/ids8313.h
@@ -0,0 +1,587 @@
+/*
+ * (C) Copyright 2013
+ * Heiko Schocher, DENX Software Engineering, hs@denx.de.
+ *
+ * Based on:
+ * Copyright (c) 2011 IDS GmbH, Germany
+ * Sergej Stepanov <ste@ids.de>
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_MPC831x
+#define CONFIG_MPC8313
+#define CONFIG_IDS8313
+
+#define CONFIG_FSL_ELBC
+
+#define CONFIG_MISC_INIT_R
+
+#define CONFIG_AUTOBOOT_KEYED
+#define CONFIG_AUTOBOOT_PROMPT	\
+	"\nEnter password - autoboot in %d seconds...\n", CONFIG_BOOTDELAY
+#define CONFIG_AUTOBOOT_DELAY_STR	"ids"
+#define CONFIG_BOOT_RETRY_TIME		900
+#define CONFIG_BOOT_RETRY_MIN		30
+#define CONFIG_BOOTDELAY		1
+#define CONFIG_RESET_TO_RETRY
+
+#define CONFIG_83XX_CLKIN		66000000	/* in Hz */
+#define CONFIG_SYS_CLK_FREQ		CONFIG_83XX_CLKIN
+
+#define CONFIG_SYS_IMMR		0xF0000000
+
+#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
+
+/*
+ * Hardware Reset Configuration Word
+ * if CLKIN is 66.000MHz, then
+ * CSB = 132MHz, CORE = 264MHz, DDRC = 264MHz, LBC = 132MHz
+ */
+#define CONFIG_SYS_HRCW_LOW (0x20000000 /* reserved, must be set */ |\
+			     HRCWL_DDR_TO_SCB_CLK_2X1 |\
+			     HRCWL_CSB_TO_CLKIN_2X1 |\
+			     HRCWL_CORE_TO_CSB_2X1)
+
+#define CONFIG_SYS_HRCW_HIGH	(HRCWH_PCI_HOST |\
+				 HRCWH_CORE_ENABLE |\
+				 HRCWH_FROM_0XFFF00100 |\
+				 HRCWH_BOOTSEQ_DISABLE |\
+				 HRCWH_SW_WATCHDOG_DISABLE |\
+				 HRCWH_ROM_LOC_LOCAL_8BIT |\
+				 HRCWH_RL_EXT_LEGACY |\
+				 HRCWH_TSEC1M_IN_MII |\
+				 HRCWH_TSEC2M_IN_MII |\
+				 HRCWH_BIG_ENDIAN)
+
+#define CONFIG_SYS_SICRH	0x00000000
+#define CONFIG_SYS_SICRL	(SICRL_LBC | SICRL_SPI_D)
+
+#define CONFIG_HWCONFIG
+
+#define CONFIG_SYS_HID0_INIT	0x000000000
+#define CONFIG_SYS_HID0_FINAL	(HID0_ENABLE_MACHINE_CHECK |\
+				 HID0_ENABLE_INSTRUCTION_CACHE |\
+				 HID0_DISABLE_DYNAMIC_POWER_MANAGMENT)
+
+#define CONFIG_SYS_HID2	(HID2_HBE | 0x00020000)
+
+/*
+ * Definitions for initial stack pointer and data area (in DCACHE )
+ */
+#define CONFIG_SYS_INIT_RAM_LOCK
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000
+#define CONFIG_SYS_INIT_RAM_SIZE	0x1000  /* End of used area in DPRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE \
+					 - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
+
+/*
+ * Local Bus LCRR and LBCR regs
+ */
+#define CONFIG_SYS_LCRR_EADC		LCRR_EADC_1
+#define CONFIG_SYS_LCRR_CLKDIV		LCRR_CLKDIV_2
+#define CONFIG_SYS_LBC_LBCR		(0x00040000 |\
+					 (0xFF << LBCR_BMT_SHIFT) |\
+					 0xF)
+
+#define CONFIG_SYS_LBC_MRTPR		0x20000000
+
+/*
+ * Internal Definitions
+ */
+/*
+ * DDR Setup
+ */
+#define CONFIG_SYS_DDR_BASE		0x00000000
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+
+/*
+ * Manually set up DDR parameters,
+ * as this board has not the SPD connected to I2C.
+ */
+#define CONFIG_SYS_DDR_SIZE		256		/* MB */
+#define CONFIG_SYS_DDR_CONFIG		(CSCONFIG_EN |\
+					 0x00010000 |\
+					 CSCONFIG_ROW_BIT_13 |\
+					 CSCONFIG_COL_BIT_10)
+
+#define CONFIG_SYS_DDR_CONFIG_256	(CONFIG_SYS_DDR_CONFIG | \
+					 CSCONFIG_BANK_BIT_3)
+
+#define CONFIG_SYS_DDR_TIMING_3	(1 << 16)	/* ext refrec */
+#define CONFIG_SYS_DDR_TIMING_0	((3 << TIMING_CFG0_RWT_SHIFT) |\
+				(3 << TIMING_CFG0_WRT_SHIFT) |\
+				(3 << TIMING_CFG0_RRT_SHIFT) |\
+				(3 << TIMING_CFG0_WWT_SHIFT) |\
+				(6 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) |\
+				(2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) |\
+				(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
+				(2 << TIMING_CFG0_MRS_CYC_SHIFT))
+#define CONFIG_SYS_DDR_TIMING_1	((4 << TIMING_CFG1_PRETOACT_SHIFT) |\
+				(12 << TIMING_CFG1_ACTTOPRE_SHIFT) |\
+				(4 << TIMING_CFG1_ACTTORW_SHIFT) |\
+				(7 << TIMING_CFG1_CASLAT_SHIFT) |\
+				(4 << TIMING_CFG1_REFREC_SHIFT) |\
+				(4 << TIMING_CFG1_WRREC_SHIFT) |\
+				(2 << TIMING_CFG1_ACTTOACT_SHIFT) |\
+				(2 << TIMING_CFG1_WRTORD_SHIFT))
+#define CONFIG_SYS_DDR_TIMING_2	((1 << TIMING_CFG2_ADD_LAT_SHIFT) |\
+				(5 << TIMING_CFG2_CPO_SHIFT) |\
+				(4 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) |\
+				(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) |\
+				(0 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) |\
+				(1 << TIMING_CFG2_CKE_PLS_SHIFT) |\
+				(6 << TIMING_CFG2_FOUR_ACT_SHIFT))
+
+#define CONFIG_SYS_DDR_INTERVAL	((0x800 << SDRAM_INTERVAL_REFINT_SHIFT) |\
+				(0x800 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
+
+#define CONFIG_SYS_SDRAM_CFG		(SDRAM_CFG_SREN |\
+					 SDRAM_CFG_2T_EN | SDRAM_CFG_HSE |\
+					 SDRAM_CFG_DBW_32 |\
+					 SDRAM_CFG_SDRAM_TYPE_DDR2)
+
+#define CONFIG_SYS_SDRAM_CFG2		0x00401000
+#define CONFIG_SYS_DDR_MODE		((0x0448 << SDRAM_MODE_ESD_SHIFT) |\
+					 (0x0242 << SDRAM_MODE_SD_SHIFT))
+#define CONFIG_SYS_DDR_MODE_2		0x00000000
+#define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075
+#define CONFIG_SYS_DDRCDR_VALUE	(DDRCDR_EN |\
+					 DDRCDR_PZ_NOMZ |\
+					 DDRCDR_NZ_NOMZ |\
+					 DDRCDR_ODT |\
+					 DDRCDR_M_ODR |\
+					 DDRCDR_Q_DRN)
+
+/*
+ * on-board devices
+ */
+#define CONFIG_TSEC1
+#define CONFIG_TSEC2
+#define CONFIG_TSEC_ENET
+#define CONFIG_NET_MULTI
+#define CONFIG_HARD_SPI
+#define CONFIG_HARD_I2C
+
+/*
+ * NOR FLASH setup
+ */
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
+#define CONFIG_FLASH_SHOW_PROGRESS	50
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
+
+#define CONFIG_SYS_FLASH_BASE		0xFF800000
+#define CONFIG_SYS_FLASH_SIZE		8
+#define CONFIG_SYS_FLASH_PROTECTION
+
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000016
+
+#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE |\
+					 BR_PS_8 |\
+					 BR_MS_GPCM |\
+					 BR_V)
+
+#define CONFIG_SYS_OR0_PRELIM		(MEG_TO_AM(CONFIG_SYS_FLASH_SIZE) |\
+					 OR_GPCM_SCY_10 |\
+					 OR_GPCM_EHTR |\
+					 OR_GPCM_TRLX |\
+					 OR_GPCM_CSNT |\
+					 OR_GPCM_EAD)
+#define CONFIG_SYS_MAX_FLASH_BANKS	1
+#define CONFIG_SYS_MAX_FLASH_SECT	128
+
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500
+
+/*
+ * NAND FLASH setup
+ */
+#define CONFIG_SYS_NAND_BASE		0xE1000000
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_NAND_MAX_CHIPS	1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_NAND_FSL_ELBC
+#define CONFIG_SYS_NAND_PAGE_SIZE	(2048)
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 << 10)
+#define NAND_CACHE_PAGES		64
+
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E
+#define CONFIG_SYS_NAND_LBLAWBAR_PRELIM CONFIG_SYS_LBLAWBAR1_PRELIM
+#define CONFIG_SYS_NAND_LBLAWAR_PRELIM	CONFIG_SYS_LBLAWAR1_PRELIM
+
+#define CONFIG_SYS_BR1_PRELIM	((CONFIG_SYS_NAND_BASE) |\
+				 (2<<BR_DECC_SHIFT) |\
+				 BR_PS_8 |\
+				 BR_MS_FCM |\
+				 BR_V)
+
+#define CONFIG_SYS_OR1_PRELIM	(0xFFFF8000 |\
+				 OR_FCM_PGS |\
+				 OR_FCM_CSCT |\
+				 OR_FCM_CST |\
+				 OR_FCM_CHT |\
+				 OR_FCM_SCY_4 |\
+				 OR_FCM_TRLX |\
+				 OR_FCM_EHTR |\
+				 OR_FCM_RST)
+
+/*
+ * MRAM setup
+ */
+#define CONFIG_SYS_MRAM_BASE		0xE2000000
+#define CONFIG_SYS_MRAM_SIZE		0x20000	/* 128 Kb */
+#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_MRAM_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000010	/* 128 Kb  */
+
+#define CONFIG_SYS_OR_TIMING_MRAM
+
+#define CONFIG_SYS_BR2_PRELIM		(CONFIG_SYS_MRAM_BASE |\
+					 BR_PS_8 |\
+					 BR_MS_GPCM |\
+					 BR_V)
+
+#define CONFIG_SYS_OR2_PRELIM		0xFFFE0C74
+
+/*
+ * CPLD setup
+ */
+#define CONFIG_SYS_CPLD_BASE		0xE3000000
+#define CONFIG_SYS_CPLD_SIZE		0x8000
+#define CONFIG_SYS_LBLAWBAR3_PRELIM	CONFIG_SYS_CPLD_BASE
+#define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000000E
+
+#define CONFIG_SYS_OR_TIMING_MRAM
+
+#define CONFIG_SYS_BR3_PRELIM		(CONFIG_SYS_CPLD_BASE |\
+					 BR_PS_8 |\
+					 BR_MS_GPCM |\
+					 BR_V)
+
+#define CONFIG_SYS_OR3_PRELIM		0xFFFF8814
+
+/*
+ * HW-Watchdog
+ */
+#define CONFIG_WATCHDOG		1
+#define CONFIG_SYS_WATCHDOG_VALUE	0xFFFF
+
+/*
+ * I2C setup
+ */
+#define CONFIG_CMD_I2C
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	400000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3100
+#define CONFIG_RTC_PCF8563
+#define CONFIG_SYS_I2C_RTC_ADDR	0x51
+
+/*
+ * SPI setup
+ */
+#ifdef CONFIG_HARD_SPI
+#define CONFIG_MPC8XXX_SPI
+#define CONFIG_CMD_SPI
+#define CONFIG_SYS_GPIO1_PRELIM
+#define CONFIG_SYS_GPIO1_DIR		0x00000001
+#define CONFIG_SYS_GPIO1_DAT		0x00000001
+#endif
+
+/*
+ * Ethernet setup
+ */
+#ifdef CONFIG_TSEC1
+#define CONFIG_HAS_ETH0
+#define CONFIG_TSEC1_NAME		"TSEC0"
+#define CONFIG_SYS_TSEC1_OFFSET	0x24000
+#define TSEC1_PHY_ADDR			0x1
+#define TSEC1_FLAGS			TSEC_GIGABIT
+#define TSEC1_PHYIDX			0
+#endif
+
+#ifdef CONFIG_TSEC2
+#define CONFIG_HAS_ETH1
+#define CONFIG_TSEC2_NAME		"TSEC1"
+#define CONFIG_SYS_TSEC2_OFFSET	0x25000
+#define TSEC2_PHY_ADDR			0x3
+#define TSEC2_FLAGS			TSEC_GIGABIT
+#define TSEC2_PHYIDX			0
+#endif
+#define CONFIG_ETHPRIME		"TSEC1"
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX		1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+
+#define CONFIG_SYS_BAUDRATE_TABLE	\
+	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR + 0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR + 0x4600)
+#define CONFIG_SYS_NS16550_CLK		(CONFIG_83XX_CLKIN * 2)
+
+#define CONFIG_HAS_FSL_DR_USB
+#define CONFIG_SYS_SCCR_USBDRCM	3
+
+/*
+ * BAT's
+ */
+#define CONFIG_HIGH_BATS
+
+/* DDR @ 0x00000000 */
+#define CONFIG_SYS_IBAT0L		(CONFIG_SYS_SDRAM_BASE |\
+					 BATL_PP_10)
+#define CONFIG_SYS_IBAT0U		(CONFIG_SYS_SDRAM_BASE |\
+					 BATU_BL_256M |\
+					 BATU_VS |\
+					 BATU_VP)
+#define CONFIG_SYS_DBAT0L		CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U		CONFIG_SYS_IBAT0U
+
+/* Initial RAM @ 0xFD000000 */
+#define CONFIG_SYS_IBAT1L		(CONFIG_SYS_INIT_RAM_ADDR |\
+					 BATL_PP_10 |\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT1U		(CONFIG_SYS_INIT_RAM_ADDR |\
+					 BATU_BL_256K |\
+					 BATU_VS |\
+					 BATU_VP)
+#define CONFIG_SYS_DBAT1L		CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U		CONFIG_SYS_IBAT1U
+
+/* FLASH @ 0xFF800000 */
+#define CONFIG_SYS_IBAT2L		(CONFIG_SYS_FLASH_BASE |\
+					 BATL_PP_10 |\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U		(CONFIG_SYS_FLASH_BASE |\
+					 BATU_BL_8M |\
+					 BATU_VS |\
+					 BATU_VP)
+#define CONFIG_SYS_DBAT2L		(CONFIG_SYS_FLASH_BASE |\
+					 BATL_PP_10 |\
+					 BATL_CACHEINHIBIT |\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_DBAT2U		CONFIG_SYS_IBAT2U
+
+#define CONFIG_SYS_IBAT3L		(0)
+#define CONFIG_SYS_IBAT3U		(0)
+#define CONFIG_SYS_DBAT3L		CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U		CONFIG_SYS_IBAT3U
+
+#define CONFIG_SYS_IBAT4L		(0)
+#define CONFIG_SYS_IBAT4U		(0)
+#define CONFIG_SYS_DBAT4L		CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U		CONFIG_SYS_IBAT4U
+
+/* IMMRBAR @ 0xF0000000 */
+#define CONFIG_SYS_IBAT5L		(CONFIG_SYS_IMMR |\
+					 BATL_PP_10 |\
+					 BATL_CACHEINHIBIT |\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U		(CONFIG_SYS_IMMR |\
+					 BATU_BL_128M |\
+					 BATU_VS |\
+					 BATU_VP)
+#define CONFIG_SYS_DBAT5L		CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U		CONFIG_SYS_IBAT5U
+
+/* NAND-Flash @ 0xE1000000, MRAM @ 0xE2000000, CPLD @ 0xE3000000 */
+#define CONFIG_SYS_IBAT6L		(0xE0000000 |\
+					 BATL_PP_10 |\
+					 BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT6U		(0xE0000000 |\
+					 BATU_BL_256M |\
+					 BATU_VS |\
+					 BATU_VP)
+#define CONFIG_SYS_DBAT6L		CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U		CONFIG_SYS_IBAT6U
+
+#define CONFIG_SYS_IBAT7L		(0)
+#define CONFIG_SYS_IBAT7U		(0)
+#define CONFIG_SYS_DBAT7L		CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U		CONFIG_SYS_IBAT7U
+
+/*
+ * U-Boot environment setup
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_SNTP
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_DATE
+#define CONFIG_CMDLINE_EDITING
+#define CONFIG_CMD_EDITENV
+#define CONFIG_CMD_JFFS2
+#define CONFIG_BOOTP_SUBNETMASK
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_BOOTFILESIZE
+/* pass open firmware flat tree */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+#define CONFIG_OF_STDOUT_VIA_ALIAS
+
+/*
+ * The reserved memory
+ */
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN		(768 * 1024)
+#define CONFIG_SYS_MALLOC_LEN		(8 * 1024 * 1024)
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE \
+				+ CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_ENV_SIZE		0x20000
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
+
+
+#define CONFIG_NETDEV			eth1
+#define CONFIG_HOSTNAME		ids8313
+#define CONFIG_ROOTPATH		"/opt/eldk-4.2/ppc_6xx"
+#define CONFIG_BOOTFILE		"ids8313/uImage"
+#define CONFIG_UBOOTPATH		"ids8313/u-boot.bin"
+#define CONFIG_FDTFILE			"ids8313/ids8313.dtb"
+#define CONFIG_LOADADDR		0x400000
+#define CONFIG_CMD_ENV_FLAGS
+#define CONFIG_ENV_FLAGS_LIST_STATIC "ethaddr:mo,eth1addr:mo"
+
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SYS_HZ			1000
+
+/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ		(256 << 20)
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP
+#define CONFIG_SYS_PROMPT		"=> "
+#define CONFIG_SYS_CBSIZE		1024
+#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE \
+					 + sizeof(CONFIG_SYS_PROMPT)+16)
+#define CONFIG_SYS_MAXARGS		16
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
+#define CONFIG_SYS_HUSH_PARSER		/* use "hush" command parser	*/
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
+
+#define CONFIG_SYS_MEMTEST_START	0x00001000
+#define CONFIG_SYS_MEMTEST_END		0x00C00000
+
+#define CONFIG_SYS_LOAD_ADDR		0x100000
+#define CONFIG_MII
+#define CONFIG_LOADS_ECHO
+#define CONFIG_TIMESTAMP
+#define CONFIG_PREBOOT			"echo;" \
+					"echo Type \\\"run nfsboot\\\" " \
+					"to mount root filesystem over NFS;echo"
+#undef	CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND		"run boot_cramfs"
+#undef	CONFIG_SYS_LOADS_BAUD_CHANGE
+
+#define CONFIG_JFFS2_NAND
+#define CONFIG_JFFS2_DEV		"0"
+
+/* mtdparts command line support */
+#define CONFIG_CMD_MTDPARTS
+#define CONFIG_FLASH_CFI_MTD
+#define CONFIG_MTD_DEVICE
+#define MTDIDS_DEFAULT		"nor0=ff800000.flash,nand0=e1000000.flash"
+#define MTDPARTS_DEFAULT	"mtdparts=ff800000.flash:7m(dum)," \
+					"768k(BOOT-BIN)," \
+					"128k(BOOT-ENV),128k(BOOT-REDENV);" \
+					"e1000000.flash:-(ubi)"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+	"netdev=" __stringify(CONFIG_NETDEV) "\0"			\
+	"ethprime=TSEC1\0"						\
+	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"			\
+	"tftpflash=tftpboot ${loadaddr} ${uboot}; "			\
+		"protect off " __stringify(CONFIG_SYS_TEXT_BASE)	\
+		" +${filesize}; "					\
+		"erase " __stringify(CONFIG_SYS_TEXT_BASE)		\
+		" +${filesize}; "					\
+		"cp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
+		" ${filesize}; "					\
+		"protect on " __stringify(CONFIG_SYS_TEXT_BASE)		\
+		" +${filesize}; "					\
+		"cmp.b ${loadaddr} " __stringify(CONFIG_SYS_TEXT_BASE)	\
+		" ${filesize}\0"					\
+	"console=ttyS0\0"						\
+	"fdtaddr=0x780000\0"						\
+	"kernel_addr=ff800000\0"					\
+	"fdtfile=" __stringify(CONFIG_FDTFILE) "\0"			\
+	"setbootargs=setenv bootargs "					\
+		"root=${rootdev} rw console=${console},"		\
+			"${baudrate} ${othbootargs}\0"			\
+	"setipargs=setenv bootargs root=${rootdev} rw "			\
+			"nfsroot=${serverip}:${rootpath} "		\
+			"ip=${ipaddr}:${serverip}:${gatewayip}:"	\
+			"${netmask}:${hostname}:${netdev}:off "		\
+			"console=${console},${baudrate} ${othbootargs}\0" \
+	"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0"		\
+	"mtdids=" MTDIDS_DEFAULT "\0"					\
+	"mtdparts=" MTDPARTS_DEFAULT "\0"				\
+	"\0"
+
+#define CONFIG_NFSBOOTCOMMAND						\
+	"setenv rootdev /dev/nfs;"					\
+	"run setipargs;run addmtd;"					\
+	"tftp ${loadaddr} ${bootfile};"				\
+	"tftp ${fdtaddr} ${fdtfile};"					\
+	"fdt addr ${fdtaddr};"						\
+	"bootm ${loadaddr} - ${fdtaddr}"
+
+/* UBI Support */
+#define CONFIG_CMD_NAND_TRIMFFS
+#define CONFIG_CMD_UBI
+#define CONFIG_CMD_UBIFS
+#define CONFIG_RBTREE
+#define CONFIG_LZO
+#define CONFIG_MTD_PARTITIONS
+
+/* bootcount support */
+#define CONFIG_BOOTCOUNT_LIMIT
+#define CONFIG_BOOTCOUNT_I2C
+#define CONFIG_BOOTCOUNT_ALEN	1
+#define CONFIG_SYS_BOOTCOUNT_ADDR	0x9
+
+#define CONFIG_VERSION_VARIABLE
+
+#define CONFIG_FIT
+#define CONFIG_FIT_SIGNATURE
+#define CONFIG_CMD_FDT
+#define CONFIG_CMD_HASH
+#define CONFIG_RSA
+#define CONFIG_SHA1
+#define CONFIG_SHA256
+#define CONFIG_OF_CONTROL
+
+#endif	/* __CONFIG_H */