ColdFire: Update Freescale MCF52x2 platforms

Signed-off-by: TsiChungLiew <Tsi-Chung.Liew@freescale.com>

3 files changed, 261 insertions, 91 deletions

diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h
index 885a882..0f97050 100644
--- a/include/configs/M5271EVB.h
+++ b/include/configs/M5271EVB.h
@@ -31,7 +31,6 @@
 #ifndef _M5271EVB_H
 #define _M5271EVB_H
 
-#define DEBUG
 #undef DEBUG
 
 /*
@@ -41,17 +40,15 @@
 #define CONFIG_M5271		/* define processor type */
 #define CONFIG_M5271EVB		/* define board type */
 
-#define CONFIG_IPADDR		192.168.30.1
-#define CONFIG_SERVERIP		192.168.1.1
-#define CONFIG_ETHADDR		00:06:3b:01:41:55
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
 
 #undef CONFIG_WATCHDOG		/* disable watchdog */
 
-#define CONFIG_BOOTDELAY	5
-
 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
  */
@@ -73,7 +70,6 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
@@ -81,22 +77,83 @@
 
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_MISC
 
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+/* I2C */
+#define CONFIG_FSL_I2C
+#define CONFIG_HARD_I2C		/* I2C with hw support */
+#undef CONFIG_SOFT_I2C		/* I2C bit-banged */
+#define CFG_I2C_SPEED		80000
+#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_OFFSET		0x00000300
+#define CFG_IMMR		CFG_MBAR
+
+#define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
+#define CONFIG_BOOTFILE		"u-boot.bin"
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_RETRY_COUNT	5
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* FEC_ENET */
+
+#define CONFIG_HOSTNAME		M5235EVB
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe2ffff;"		\
+	"era ffe00000 ffe2ffff;"				\
+	"cp.b ${loadaddr} 0 ${filesize};"	\
+	"save\0"				\
+	""
 
 #define CFG_PROMPT		"=> "
-#define CFG_LONGHELP				/* undef to save memory		*/
+#define CFG_LONGHELP		/* undef to save memory */
 
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
 
 #define CFG_LOAD_ADDR		0x00100000
 
@@ -114,16 +171,11 @@
 
 #define CFG_MBAR		0x40000000	/* Register Base Addrs */
 
-/* Enable FEC ethernet */
-#define FEC_ENET
-#define CONFIG_NET_RETRY_COUNT	5
-#define CFG_ENET_BD_BASE	0x480000
-
 /*
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	0x20000000
-#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM	*/
+#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM    */
 #define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
@@ -134,7 +186,7 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define CFG_SDRAM_SIZE		16		/* SDRAM size in MB */
+#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
 #define CFG_FLASH_BASE		0xffe00000
 
 #ifdef	CONFIG_MONITOR_IS_IN_RAM
@@ -152,11 +204,11 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /* FLASH organization */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks           */
+#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip    */
 #define CFG_FLASH_ERASE_TOUT	1000
 
 #define CFG_FLASH_CFI		1
@@ -169,4 +221,4 @@
 /* Port configuration */
 #define CFG_FECI2C		0xF0
 
-#endif	/* _M5271EVB_H */
+#endif				/* _M5271EVB_H */
diff --git a/include/configs/M5272C3.h b/include/configs/M5272C3.h
index cc456dc..2b8734b 100644
--- a/include/configs/M5272C3.h
+++ b/include/configs/M5272C3.h
@@ -33,18 +33,20 @@
  * High Level Configuration Options
  * (easy to change)
  */
-#define CONFIG_MCF52x2			/* define processor family */
-#define CONFIG_M5272			/* define processor type */
+#define CONFIG_MCF52x2		/* define processor family */
+#define CONFIG_M5272		/* define processor type */
 
-#define FEC_ENET
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE		19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
-#define CONFIG_WATCHDOG
+#undef CONFIG_WATCHDOG
 #define CONFIG_WATCHDOG_TIMEOUT 10000	/* timeout in milliseconds */
 
-#define CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
+#undef CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
 
 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
@@ -60,7 +62,6 @@
 #define CFG_ENV_IS_IN_FLASH	1
 #endif
 
-
 /*
  * BOOTP options
  */
@@ -69,37 +70,82 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
 
 #define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MISC
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_MEMORY
 
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
-
 #define CONFIG_BOOTDELAY	5
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
+
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* CONFIG_MCFFEC */
+
+#define CONFIG_HOSTNAME		M5272C3
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe3ffff;"	\
+	"era ffe00000 ffe3ffff;"		\
+	"cp.b ${loadaddr} ffe00000 ${filesize};"\
+	"save\0"				\
+	""
 
 #define CFG_PROMPT		"-> "
-#define CFG_LONGHELP				/* undef to save memory		*/
+#define CFG_LONGHELP		/* undef to save memory */
 
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
 #define CFG_LOAD_ADDR		0x20000
-
 #define CFG_MEMTEST_START	0x400
 #define CFG_MEMTEST_END		0x380000
-
 #define CFG_HZ			1000
 #define CFG_CLK			66000000
 
@@ -108,20 +154,15 @@
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */
-
 #define CFG_MBAR		0x10000000	/* Register Base Addrs */
-
 #define CFG_SCR			0x0003;
 #define CFG_SPR			0xffff;
 
-#define CFG_DISCOVER_PHY
-#define CFG_ENET_BD_BASE	0x380000
-
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CFG_INIT_RAM_ADDR	0x20000000
-#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM	*/
+#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM    */
 #define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
@@ -132,7 +173,7 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define CFG_SDRAM_SIZE		4		/* SDRAM size in MB */
+#define CFG_SDRAM_SIZE		4	/* SDRAM size in MB */
 #define CFG_FLASH_BASE		0xffe00000
 
 #ifdef	CONFIG_MONITOR_IS_IN_RAM
@@ -150,13 +191,13 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks           */
+#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip    */
 #define CFG_FLASH_ERASE_TOUT	1000
 
 /*-----------------------------------------------------------------------
@@ -169,25 +210,18 @@
  */
 #define CFG_BR0_PRELIM		0xFFE00201
 #define CFG_OR0_PRELIM		0xFFE00014
-
 #define CFG_BR1_PRELIM		0
 #define CFG_OR1_PRELIM		0
-
 #define CFG_BR2_PRELIM		0x30000001
 #define CFG_OR2_PRELIM		0xFFF80000
-
 #define CFG_BR3_PRELIM		0
 #define CFG_OR3_PRELIM		0
-
 #define CFG_BR4_PRELIM		0
 #define CFG_OR4_PRELIM		0
-
 #define CFG_BR5_PRELIM		0
 #define CFG_OR5_PRELIM		0
-
 #define CFG_BR6_PRELIM		0
 #define CFG_OR6_PRELIM		0
-
 #define CFG_BR7_PRELIM		0x00000701
 #define CFG_OR7_PRELIM		0xFFC0007C
 
@@ -197,9 +231,8 @@
 #define CFG_PACNT		0x00000000
 #define CFG_PADDR		0x0000
 #define CFG_PADAT		0x0000
-#define CFG_PBCNT		0x55554155		/* Ethernet/UART configuration */
+#define CFG_PBCNT		0x55554155	/* Ethernet/UART configuration */
 #define CFG_PBDDR		0x0000
 #define CFG_PBDAT		0x0000
 #define CFG_PDCNT		0x00000000
-
-#endif	/* _M5272C3_H */
+#endif				/* _M5272C3_H */
diff --git a/include/configs/M5282EVB.h b/include/configs/M5282EVB.h
index f2a7644..3c17c1e 100644
--- a/include/configs/M5282EVB.h
+++ b/include/configs/M5282EVB.h
@@ -33,15 +33,17 @@
  * High Level Configuration Options
  * (easy to change)
  */
-#define	CONFIG_MCF52x2			/* define processor family */
-#define CONFIG_M5282			/* define processor type */
+#define	CONFIG_MCF52x2		/* define processor family */
+#define CONFIG_M5282		/* define processor type */
 
-#define FEC_ENET
+#define CONFIG_MCFTMR
 
+#define CONFIG_MCFUART
+#define CFG_UART_PORT		(0)
 #define CONFIG_BAUDRATE 19200
 #define CFG_BAUDRATE_TABLE { 9600 , 19200 , 38400 , 57600, 115200 }
 
-#define	CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
+#undef	CONFIG_MONITOR_IS_IN_RAM	/* define if monitor is started from a pre-loader */
 
 /* Configuration for environment
  * Environment is embedded in u-boot in the second sector of the flash
@@ -50,7 +52,6 @@
 #define CFG_ENV_SIZE		0x2000
 #define CFG_ENV_IS_IN_FLASH	1
 
-
 /*
  * BOOTP options
  */
@@ -59,29 +60,73 @@
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 
-
 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_MII
 
 #undef CONFIG_CMD_LOADS
 #undef CONFIG_CMD_LOADB
 
+#define CONFIG_MCFFEC
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_NET_MULTI		1
+#	define CONFIG_MII		1
+#	define CFG_DISCOVER_PHY
+#	define CFG_RX_ETH_BUFFER	8
+#	define CFG_FAULT_ECHO_LINK_DOWN
+
+#	define CFG_FEC0_PINMUX		0
+#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define MCFFEC_TOUT_LOOP 	50000
+/* If CFG_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CFG_DISCOVER_PHY
+#		define FECDUPLEX	FULL
+#		define FECSPEED		_100BASET
+#	else
+#		ifndef CFG_FAULT_ECHO_LINK_DOWN
+#			define CFG_FAULT_ECHO_LINK_DOWN
+#		endif
+#	endif			/* CFG_DISCOVER_PHY */
+#endif
 
 #define CONFIG_BOOTDELAY	5
+#ifdef CONFIG_MCFFEC
+#	define CONFIG_ETHADDR	00:e0:0c:bc:e5:60
+#	define CONFIG_IPADDR	192.162.1.2
+#	define CONFIG_NETMASK	255.255.255.0
+#	define CONFIG_SERVERIP	192.162.1.1
+#	define CONFIG_GATEWAYIP	192.162.1.1
+#	define CONFIG_OVERWRITE_ETHADDR_ONCE
+#endif				/* CONFIG_MCFFEC */
+
+#define CONFIG_HOSTNAME		M5272C3
+#define CONFIG_EXTRA_ENV_SETTINGS		\
+	"netdev=eth0\0"				\
+	"loadaddr=10000\0"			\
+	"u-boot=u-boot.bin\0"			\
+	"load=tftp ${loadaddr) ${u-boot}\0"	\
+	"upd=run load; run prog\0"		\
+	"prog=prot off ffe00000 ffe3ffff;"	\
+	"era ffe00000 ffe3ffff;"		\
+	"cp.b ${loadaddr} ffe00000 ${filesize};"\
+	"save\0"				\
+	""
 
 #define CFG_PROMPT		"-> "
-#define	CFG_LONGHELP				/* undef to save memory		*/
+#define	CFG_LONGHELP		/* undef to save memory         */
 
 #if defined(CONFIG_CMD_KGDB)
-#define	CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#define	CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
-#define	CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define	CFG_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
-#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define	CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
+#define	CFG_MAXARGS		16	/* max number of command args   */
+#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
 
 #define CFG_LOAD_ADDR		0x20000
 
@@ -91,6 +136,10 @@
 #define CFG_HZ			1000000
 #define	CFG_CLK			64000000
 
+/* PLL Configuration: Ext Clock * 6 (see table 9-4 of MCF user manual) */
+
+#define CFG_MFD			0x02	/* PLL Multiplication Factor Devider */
+#define CFG_RFD			0x00	/* PLL Reduce Frecuency Devider */
 
 /*
  * Low Level Configuration Settings
@@ -99,15 +148,12 @@
  */
 #define	CFG_MBAR		0x40000000
 
-#undef	CFG_DISCOVER_PHY
-#define	CFG_ENET_BD_BASE	0x380000
-
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_RAM_ADDR       0x20000000
-#define CFG_INIT_RAM_END	0x10000		/* End of used area in internal SRAM	*/
-#define CFG_GBL_DATA_SIZE	64      	/* size in bytes reserved for initial data */
+#define CFG_INIT_RAM_ADDR	0x20000000
+#define CFG_INIT_RAM_END	0x10000	/* End of used area in internal SRAM    */
+#define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
@@ -117,49 +163,88 @@
  * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
 #define CFG_SDRAM_BASE		0x00000000
-#define	CFG_SDRAM_SIZE		4		/* SDRAM size in MB */
+#define	CFG_SDRAM_SIZE		8	/* SDRAM size in MB */
 #define CFG_FLASH_BASE		0xffe00000
 #define	CFG_INT_FLASH_BASE	0xf0000000
+#define CFG_INT_FLASH_ENABLE	0x21
 
 /* If M5282 port is fully implemented the monitor base will be behind
  * the vector table. */
-/* #define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400) */
-#define CFG_MONITOR_BASE	0x20000
+#if (TEXT_BASE != CFG_INT_FLASH_BASE)
+#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#else
+#define CFG_MONITOR_BASE	(TEXT_BASE + 0x418)	/* 24 Byte for CFM-Config */
+#endif
 
 #define CFG_MONITOR_LEN		0x20000
 #define CFG_MALLOC_LEN		(256 << 10)
 #define CFG_BOOTPARAMS_LEN	64*1024
 
-
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define	CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
-
+#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define	CFG_MAX_FLASH_SECT	35
-#define	CFG_MAX_FLASH_BANKS	1
-#define	CFG_FLASH_ERASE_TOUT	10000000
+#define CFG_FLASH_CFI
+#ifdef CFG_FLASH_CFI
+
+#	define CFG_FLASH_CFI_DRIVER	1
+#	define CFG_FLASH_SIZE		0x1000000	/* Max size that the board might have */
+#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#	define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#	define CFG_MAX_FLASH_SECT	137	/* max number of sectors on one chip */
+#	define CFG_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
+#	define CFG_FLASH_CHECKSUM
+#	define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#endif
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE	16
 
-
 /*-----------------------------------------------------------------------
  * Memory bank definitions
  */
-
-
+#define CFG_CS0_BASE		CFG_FLASH_BASE
+#define CFG_CS0_SIZE		2*1024*1024
+#define CFG_CS0_WIDTH		16
+#define CFG_CS0_RO 		0
+#define CFG_CS0_WS		6
+/*
+#define CFG_CS3_BASE		0xE0000000
+#define CFG_CS3_SIZE		1*1024*1024
+#define CFG_CS3_WIDTH		16
+#define CFG_CS3_RO 		0
+#define CFG_CS3_WS		6
+*/
 /*-----------------------------------------------------------------------
  * Port configuration
  */
+#define CFG_PACNT		0x0000000	/* Port A D[31:24] */
+#define CFG_PADDR		0x0000000
+#define CFG_PADAT		0x0000000
+
+#define CFG_PBCNT		0x0000000	/* Port B D[23:16] */
+#define CFG_PBDDR		0x0000000
+#define CFG_PBDAT		0x0000000
+
+#define CFG_PCCNT		0x0000000	/* Port C D[15:08] */
+#define CFG_PCDDR		0x0000000
+#define CFG_PCDAT		0x0000000
+
+#define CFG_PDCNT		0x0000000	/* Port D D[07:00] */
+#define CFG_PCDDR		0x0000000
+#define CFG_PCDAT		0x0000000
 
+#define CFG_PEHLPAR		0xC0
+#define CFG_PUAPAR		0x0F	/* UA0..UA3 = Uart 0 +1 */
+#define CFG_DDRUA		0x05
+#define CFG_PJPAR 		0xFF;
 
-#endif	/* _CONFIG_M5282EVB_H */
+#endif				/* _CONFIG_M5282EVB_H */