Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xx

21 files changed, 699 insertions, 2429 deletions

diff --git a/include/configs/CPCI4052.h b/include/configs/CPCI4052.h
index b248639..fd49f56 100644
--- a/include/configs/CPCI4052.h
+++ b/include/configs/CPCI4052.h
@@ -88,32 +88,17 @@
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_BSP
 #define CONFIG_CMD_EEPROM
 
-
-#if 0 /* test-only */
-#define CONFIG_NETCONSOLE
-#define CONFIG_NET_MULTI
-
-#ifdef CONFIG_NET_MULTI
-#define CONFIG_PHY1_ADDR	1	/* PHY address: for NetConsole	*/
-#endif
-#endif
-
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
 
 #define CONFIG_SUPPORT_VFAT
 
-#if 0 /* test-only */
-#define CONFIG_AUTO_UPDATE      1       /* autoupdate via compactflash  */
-#endif
-
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
@@ -256,29 +241,6 @@
 
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-
-/*
- * JFFS2 partitions
- */
-
-/* No command line, one static partition, use whole device */
-#undef CONFIG_JFFS2_CMDLINE
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00000000
-
-/* mtdparts command line support */
-
-/* Use first bank for JFFS2, second bank contains U-Boot.
- *
- * Note: fake mtd_id's used, no linux mtd map file.
- */
-/*
-#define CONFIG_JFFS2_CMDLINE
-#define MTDIDS_DEFAULT		"nor0=cpci4052-0"
-#define MTDPARTS_DEFAULT	"mtdparts=cpci4052-0:-(jffs2)"
-*/
-
 #if 0 /* Use NVRAM for environment variables */
 /*-----------------------------------------------------------------------
  * NVRAM organization
diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h
index 1e9597d..55dd629 100644
--- a/include/configs/CPCI405AB.h
+++ b/include/configs/CPCI405AB.h
@@ -88,7 +88,6 @@
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING
@@ -238,27 +237,6 @@
 
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-/*
- * JFFS2 partitions
- */
-/* No command line, one static partition */
-#undef CONFIG_JFFS2_CMDLINE
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00000000
-
-/* mtdparts command line support */
-
-/* Use first bank for JFFS2, second bank contains U-Boot.
- *
- * Note: fake mtd_id's used, no linux mtd map file.
- */
-/*
-#define CONFIG_JFFS2_CMDLINE
-#define MTDIDS_DEFAULT		"nor0=cpci405ab-0"
-#define MTDPARTS_DEFAULT	"mtdparts=cpci405ab-0:-(jffs2)"
-*/
-
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC32) for environment
  */
diff --git a/include/configs/CPCI405DT.h b/include/configs/CPCI405DT.h
index a8029ea..6b585be 100644
--- a/include/configs/CPCI405DT.h
+++ b/include/configs/CPCI405DT.h
@@ -87,23 +87,12 @@
 #define CONFIG_CMD_FAT
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_I2C
 #define CONFIG_CMD_MII
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_BSP
 #define CONFIG_CMD_EEPROM
 
-
-#if 0 /* test-only */
-#define CONFIG_NETCONSOLE
-#define CONFIG_NET_MULTI
-
-#ifdef CONFIG_NET_MULTI
-#define CONFIG_PHY1_ADDR	1	/* PHY address: for NetConsole	*/
-#endif
-#endif
-
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
 
@@ -260,27 +249,6 @@
 
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-/*
- * JFFS2 partitions
- */
-/* No command line, one static partition */
-#undef CONFIG_JFFS2_CMDLINE
-#define CONFIG_JFFS2_DEV		"nor0"
-#define CONFIG_JFFS2_PART_SIZE		0xFFFFFFFF
-#define CONFIG_JFFS2_PART_OFFSET	0x00000000
-
-/* mtdparts command line support */
-
-/* Use first bank for JFFS2, second bank contains U-Boot.
- *
- * Note: fake mtd_id's used, no linux mtd map file.
- */
-/*
-#define CONFIG_JFFS2_CMDLINE
-#define MTDIDS_DEFAULT		"nor0=cpci405dt-0"
-#define MTDPARTS_DEFAULT	"mtdparts=cpci405dt-0:-(jffs2)"
-*/
-
 #if 0 /* Use NVRAM for environment variables */
 /*-----------------------------------------------------------------------
  * NVRAM organization
@@ -416,7 +384,6 @@
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
-
 /*
  * Internal Definitions
  *
diff --git a/include/configs/acadia.h b/include/configs/acadia.h
index bbf726d..9092a7c 100644
--- a/include/configs/acadia.h
+++ b/include/configs/acadia.h
@@ -34,6 +34,13 @@
 #define CONFIG_ACADIA		1		/* Board is Acadia	*/
 #define CONFIG_4xx		1		/* ... PPC4xx family	*/
 #define CONFIG_405EZ		1		/* Specifc 405EZ support*/
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		acadia
+#include "amcc-common.h"
+
 /* Detect Acadia PLL input clock automatically via CPLD bit		*/
 #define CONFIG_SYS_CLK_FREQ    ((in8(CFG_CPLD_BASE + 0) == 0x0c) ? \
 				66666666 : 33333000)
@@ -59,16 +66,11 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0xfe000000
 #define CFG_CPLD_BASE		0x80000000
 #define CFG_NAND_ADDR		0xd0000000
 #define CFG_USB_HOST		0xef603000	/* USB OHCI 1.1 controller	*/
 
-#define CFG_MONITOR_BASE	TEXT_BASE
-#define CFG_MONITOR_LEN		(0xFFFFFFFF - CFG_MONITOR_BASE + 1)
-#define CFG_MALLOC_LEN		(512 * 1024)/* Reserve 512 kB for malloc()	*/
-
 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer
  *----------------------------------------------------------------------*/
@@ -89,12 +91,6 @@
  *----------------------------------------------------------------------*/
 #undef	CFG_EXT_SERIAL_CLOCK			/* external serial clock */
 #define CFG_BASE_BAUD		691200
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_SERIAL_MULTI     1
-
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
 
 /*-----------------------------------------------------------------------
  * Environment
@@ -202,10 +198,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -222,77 +215,24 @@
 #define CFG_DTT_LOW_TEMP	-30
 #define CFG_DTT_HYSTERESIS	3
 
-#if 0 /* test-only... */
-/*-----------------------------------------------------------------------
- * SPI stuff - Define to include SPI control
- *-----------------------------------------------------------------------
- */
-#define CONFIG_SPI
-#endif
-
 /*-----------------------------------------------------------------------
  * Ethernet
  *----------------------------------------------------------------------*/
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define	CONFIG_PHY_ADDR		0	/* PHY address			*/
-#define CONFIG_NET_MULTI	1
-#define CFG_RX_ETH_BUFFER	16	/* # of rx buffers & descriptors*/
 #define CONFIG_HAS_ETH0		1
 
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define xstr(s) str(s)
-#define str(s) #s
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=acadia\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-		"bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"				\
-	"bootfile=acadia/uImage\0"					\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_PPC						\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
+	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"kernel_addr=fff10000\0"					\
 	"ramdisk_addr=fff20000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 200000 acadia/u-boot.bin\0"				\
-	"update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;"	\
-		"era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;"		\
-		"cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
-	"nload=tftp 200000 acadia/u-boot-nand.bin\0"			\
-	"nupdate=nand erase 0 60000;nand write 200000 0 60000;"		\
-		"setenv filesize;saveenv\0"				\
-	"nupd=run nload nupdate\0"					\
 	"kozio=bootm ffc60000\0"					\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_USB_OHCI
 #define CONFIG_USB_STORAGE
@@ -305,35 +245,10 @@
 #define CONFIG_SUPPORT_VFAT
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_USB
 
 /*
@@ -344,43 +259,6 @@
 #undef CONFIG_CMD_IMLS
 #endif
 
-#undef CONFIG_WATCHDOG					/* watchdog disabled		*/
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
 /*-----------------------------------------------------------------------
  * NAND FLASH
  *----------------------------------------------------------------------*/
@@ -493,21 +371,4 @@
 #define CFG_GPIO1_TSRL		0x00000000
 #define CFG_GPIO1_TSRH		0x00000000
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-  #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-  #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/alpr.h b/include/configs/alpr.h
index 3e906c4..fb6feb5 100644
--- a/include/configs/alpr.h
+++ b/include/configs/alpr.h
@@ -33,7 +33,6 @@
 #define CONFIG_4xx		1	    /* ... PPC4xx family	*/
 #define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_pre_init	*/
 #define CONFIG_LAST_STAGE_INIT	1	    /* call last_stage_init()	*/
-#undef	CFG_DRAM_TEST			    /* Disable-takes long time! */
 #define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
 #define CONFIG_4xx_DCACHE		/* Enable i- and d-cache	*/
 
diff --git a/include/configs/amcc-common.h b/include/configs/amcc-common.h
new file mode 100644
index 0000000..1f27d78
--- /dev/null
+++ b/include/configs/amcc-common.h
@@ -0,0 +1,259 @@
+/*
+ * (C) Copyright 2008
+ * Stefan Roese, DENX Software Engineering, sr@denx.de.
+ *
+ * Common configuration options for all AMCC boards
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#ifndef __AMCC_COMMON_H
+#define __AMCC_COMMON_H
+
+#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
+#define CFG_MONITOR_BASE	TEXT_BASE	/* Start of U-Boot	*/
+#define CFG_MONITOR_LEN		(0xFFFFFFFF - CFG_MONITOR_BASE + 1)
+#define CFG_MALLOC_LEN		(1 << 20)	/* Reserved for malloc	*/
+
+/*
+ * UART
+ */
+#define CONFIG_BAUDRATE		115200
+#define CONFIG_SERIAL_MULTI
+#define CFG_BAUDRATE_TABLE  \
+    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
+
+/*
+ * I2C
+ */
+#define CONFIG_HARD_I2C			/* I2C with hardware support	*/
+#define CFG_I2C_SLAVE		0x7F
+
+/*
+ * Ethernet/EMAC/PHY
+ */
+#define CONFIG_MII			/* MII PHY management		*/
+#define CONFIG_NET_MULTI
+#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
+#if defined(CONFIG_440)
+#define CFG_RX_ETH_BUFFER	32	/* number of eth rx buffers	*/
+#else
+#define CFG_RX_ETH_BUFFER	16	/* number of eth rx buffers	*/
+#endif
+
+/*
+ * Commands
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#if defined(CONFIG_440)
+#define CONFIG_CMD_CACHE
+#endif
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/
+#if defined(CONFIG_CMD_KGDB)
+#define CFG_CBSIZE		1024	/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE		256	/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
+#define CFG_MAXARGS		16	/* max number of command args	*/
+#define CFG_BARGSIZE		CFG_CBSIZE /* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
+#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
+#define CFG_EXTBDINFO			/* To use extended board_into (bd_t) */
+
+#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
+
+#define CONFIG_CMDLINE_EDITING		/* add command line history	*/
+#define CONFIG_AUTO_COMPLETE		/* add autocompletion support	*/
+#define CONFIG_LOOPW			/* enable loopw command         */
+#define CONFIG_MX_CYCLIC		/* enable mdc/mwc commands      */
+#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
+#define CONFIG_VERSION_VARIABLE 	/* include version env variable */
+#define CFG_CONSOLE_INFO_QUIET		/* don't print console @ startup*/
+
+#define CFG_HUSH_PARSER			/* Use the HUSH parser		*/
+#ifdef	CFG_HUSH_PARSER
+#define	CFG_PROMPT_HUSH_PS2	"> "
+#endif
+
+#define CONFIG_LOADS_ECHO		/* echo on for serial download	*/
+#define CFG_LOADS_BAUD_CHANGE		/* allow baudrate change	*/
+
+/*
+ * BOOTP options
+ */
+#define CONFIG_BOOTP_BOOTFILESIZE
+#define CONFIG_BOOTP_BOOTPATH
+#define CONFIG_BOOTP_GATEWAY
+#define CONFIG_BOOTP_HOSTNAME
+#define CONFIG_BOOTP_SUBNETMASK
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
+
+/*
+ * Internal Definitions
+ */
+#if defined(CONFIG_CMD_KGDB)
+#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port*/
+#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use	*/
+#endif
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT
+#define CONFIG_OF_BOARD_SETUP
+
+/*
+ * Booting and default environment
+ */
+#define CONFIG_PREBOOT	"echo;"	\
+	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
+	"echo"
+#define CONFIG_BOOTCOMMAND	"run flash_self"
+
+/*
+ * Only very few boards have default console not on ttyS0 (like Taishan)
+ */
+#if !defined(CONFIG_USE_TTY)
+#define CONFIG_USE_TTY	ttyS0
+#endif
+
+/*
+ * Only some 4xx PPC's are equipped with an FPU
+ */
+#if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \
+    defined(CONFIG_460EX) || defined(CONFIG_460GT)
+#define CONFIG_AMCC_DEF_ENV_ROOTPATH	"rootpath=/opt/eldk/ppc_4xxFP\0"
+#else
+#define CONFIG_AMCC_DEF_ENV_ROOTPATH	"rootpath=/opt/eldk/ppc_4xx\0"
+#endif
+
+/*
+ * Only some boards need to extend the bootargs by some additional
+ * parameters (like Makalu)
+ */
+#if !defined(CONFIG_ADDMISC)
+#define CONFIG_ADDMISC	"addmisc=setenv bootargs ${bootargs}\0"
+#endif
+
+#define xstr(s)	str(s)
+#define str(s)	#s
+
+/*
+ * General common environment variables shared on all AMCC eval boards
+ */
+#define CONFIG_AMCC_DEF_ENV						\
+	"netdev=eth0\0"							\
+	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
+		"nfsroot=${serverip}:${rootpath}\0"			\
+	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
+	"addip=setenv bootargs ${bootargs} "				\
+		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
+		":${hostname}:${netdev}:off panic=1\0"			\
+	"addtty=setenv bootargs ${bootargs}"				\
+		" console=" xstr(CONFIG_USE_TTY) ",${baudrate}\0"	\
+	CONFIG_ADDMISC							\
+	"initrd_high=30000000\0"					\
+	"kernel_addr_r=400000\0"					\
+	"fdt_addr_r=800000\0"						\
+	"hostname=" xstr(CONFIG_HOSTNAME) "\0"				\
+	"bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0"			\
+	CONFIG_AMCC_DEF_ENV_ROOTPATH
+
+/*
+ * Default environment for arch/powerpc booting
+ * for boards that are ported to arch/powerpc
+ */
+#define CONFIG_AMCC_DEF_ENV_POWERPC					\
+	"flash_self=run ramargs addip addtty addmisc;"			\
+		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
+	"flash_nfs=run nfsargs addip addtty addmisc;"			\
+		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
+	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
+		"tftp ${fdt_addr_r} ${fdt_file}; "			\
+		"run nfsargs addip addtty addmisc;"			\
+		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
+	"fdt_file=" xstr(CONFIG_HOSTNAME) "/" xstr(CONFIG_HOSTNAME) ".dtb\0"
+
+/*
+ * Default environment for arch/ppc booting,
+ * for boards that are not ported to arch/powerpc yet
+ */
+#define CONFIG_AMCC_DEF_ENV_PPC						\
+	"flash_self=run ramargs addip addtty addmisc;"			\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"flash_nfs=run nfsargs addip addtty addmisc;"			\
+		"bootm ${kernel_addr}\0"				\
+	"net_nfs=tftp ${kernel_addr_r} ${bootfile};"			\
+		"run nfsargs addip addtty addmisc;"			\
+		"bootm ${kernel_addr_r}\0"
+
+/*
+ * Default environment for arch/ppc booting (old version),
+ * for boards that are ported to arch/ppc and arch/powerpc
+ */
+#define CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	"flash_self_old=run ramargs addip addtty addmisc;"		\
+		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
+	"flash_nfs_old=run nfsargs addip addtty addmisc;"		\
+		"bootm ${kernel_addr}\0"				\
+	"net_nfs_old=tftp ${kernel_addr_r} ${bootfile};"		\
+		"run nfsargs addip addtty addmisc;"			\
+		"bootm ${kernel_addr_r}\0"
+
+#define CONFIG_AMCC_DEF_ENV_NOR_UPD					\
+	"load=tftp 200000 " xstr(CONFIG_HOSTNAME) "/u-boot.bin\0"	\
+	"update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;"	\
+		"era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;"		\
+		"cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
+		"setenv filesize;saveenv\0"				\
+	"upd=run load update\0"						\
+
+#define CONFIG_AMCC_DEF_ENV_NAND_UPD					\
+	"nload=tftp 200000 " xstr(CONFIG_HOSTNAME) "/u-boot-nand.bin\0"	\
+	"nupdate=nand erase 0 100000;nand write 200000 0 100000;"	\
+		"setenv filesize;saveenv\0"				\
+	"nupd=run nload nupdate\0"
+
+#endif /* __AMCC_COMMON_H */
diff --git a/include/configs/bamboo.h b/include/configs/bamboo.h
index 2f0df8a..41058f8 100644
--- a/include/configs/bamboo.h
+++ b/include/configs/bamboo.h
@@ -36,6 +36,12 @@
 #define CONFIG_4xx		1	/* ... PPC4xx family	        */
 #define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		bamboo
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1     /* Call board_early_init_f	*/
 
 /*
@@ -49,10 +55,6 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
-#define CFG_MONITOR_BASE	TEXT_BASE
-#define CFG_SDRAM_BASE	        0x00000000	    /* _must_ be 0	*/
 #define CFG_FLASH_BASE	        0xfff00000	    /* start of FLASH	*/
 #define CFG_PCI_MEMBASE	        0xa0000000	    /* mapped pci memory*/
 #define CFG_PCI_MEMBASE1        CFG_PCI_MEMBASE  + 0x10000000
@@ -84,14 +86,9 @@
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CFG_EXT_SERIAL_CLOCK	11059200 /* use external 11.059MHz clk	*/
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_SERIAL_MULTI     1
 /* define this if you want console on UART1 */
 #undef CONFIG_UART1_CONSOLE
 
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * NVRAM/RTC
  *
@@ -223,15 +220,11 @@
 #define SPD_EEPROM_ADDRESS	{CFG_SIMULATE_SPD_EEPROM, 0x50, 0x51}
 #define CFG_MBYTES_SDRAM	(64)	/* 64MB fixed size for early-sdram-init */
 #define CONFIG_PROG_SDRAM_TLB
-#undef  CFG_DRAM_TEST
 
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -245,54 +238,20 @@
 #define CFG_ENV_OFFSET		0x0
 #endif /* CFG_ENV_IS_IN_EEPROM */
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=bamboo\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/bamboo/uImage\0"				\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
+	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"kernel_addr=fff00000\0"					\
 	"ramdisk_addr=fff10000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/bamboo/u-boot.bin\0"		\
-	"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;"	\
-		"cp.b 100000 fffa0000 60000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_HAS_ETH0
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address, See schematics	*/
 #define CONFIG_PHY1_ADDR        1
 
@@ -300,16 +259,6 @@
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
 #endif /* CONFIG_BAMBOO_NAND */
 
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-#define CONFIG_NET_MULTI        1       /* required for netconsole      */
-
-/* Partitions */
-#define CONFIG_MAC_PARTITION
-#define CONFIG_DOS_PARTITION
-#define CONFIG_ISO_PARTITION
-
 #ifdef CONFIG_440EP
 /* USB */
 #define CONFIG_USB_OHCI
@@ -319,77 +268,27 @@
 #define USB_2_0_DEVICE
 #endif /*CONFIG_440EP*/
 
-
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_EXT2
 #define CONFIG_CMD_SNTP
+#define CONFIG_CMD_USB
 
 #ifdef CONFIG_BAMBOO_NAND
 #define CONFIG_CMD_NAND
 #endif
 
-
 #define CONFIG_SUPPORT_VFAT
 
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on	        */
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-#define CONFIG_LYNXKDI          1       /* support kdi files            */
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
+/* Partitions */
+#define CONFIG_MAC_PARTITION
+#define CONFIG_DOS_PARTITION
+#define CONFIG_ISO_PARTITION
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -408,28 +307,4 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
 #define CFG_PCI_SUBSYS_ID       0xcafe	/* Whatever */
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/bubinga.h b/include/configs/bubinga.h
index 75dd4e7..acce82f 100644
--- a/include/configs/bubinga.h
+++ b/include/configs/bubinga.h
@@ -37,6 +37,12 @@
 #define CONFIG_4xx		1	/* ...member of PPC4xx family   */
 #define CONFIG_BUBINGA	        1	/* ...on a BUBINGA board	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		bubinga
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
 #define CONFIG_SYS_CLK_FREQ     33333333 /* external frequency to pll   */
@@ -80,118 +86,35 @@
 #define CFG_ENV_IS_IN_NVRAM	1	/* use NVRAM for environment vars	*/
 #endif
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=bubinga\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/bubinga/uImage\0"				\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_PPC						\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fff80000\0"					\
 	"ramdisk_addr=fff90000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/bubinga/u-boot.bin\0"		\
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run net_nfs"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
 
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define	CONFIG_PHY_ADDR		1	/* PHY address			*/
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #define CONFIG_PHY1_ADDR	2	/* EMAC1 PHY address		*/
-#define CONFIG_NET_MULTI	1
-#define CFG_RX_ETH_BUFFER	16	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
 
 #define CONFIG_RTC_DS174x	1	/* use DS1743 RTC in Bubinga	*/
 
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
 /*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_CACHE
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SNTP
 
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
 #define CONFIG_SPD_EEPROM      1       /* use SPD EEPROM for setup    */
 
 /*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-/*
  * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
  * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
  * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
@@ -205,29 +128,11 @@
 #undef  CFG_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */
 #define CFG_BASE_BAUD       691200
 
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
 /*-----------------------------------------------------------------------
  * I2C stuff
  *-----------------------------------------------------------------------
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef  CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_NOPROBES	{ 0x69 }	/* avoid iprobe hangup (why?) */
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	6	/* 24C02 requires 5ms delay */
@@ -272,21 +177,9 @@
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
 #define CFG_SRAM_BASE		0xFFF00000
 #define CFG_FLASH_BASE		0xFFF80000
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
-#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
  * FLASH organization
@@ -423,21 +316,4 @@
 #define FPGA_REG1_OFFB_FLASH  0x02       /* Off board flash                   */
 #define FPGA_REG1_SRAM_BOOT   0x01       /* SRAM at 0xFFF80000 not Flash      */
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/canyonlands.h b/include/configs/canyonlands.h
index 3dd577a..ac2e5d9 100644
--- a/include/configs/canyonlands.h
+++ b/include/configs/canyonlands.h
@@ -30,12 +30,19 @@
 /* This config file is used for Canyonlands (460EX) and Glacier (460GT)	*/
 #ifndef CONFIG_CANYONLANDS
 #define CONFIG_460GT		1	/* Specific PPC460GT		*/
+#define CONFIG_HOSTNAME		glacier
 #else
 #define CONFIG_460EX		1	/* Specific PPC460EX		*/
+#define CONFIG_HOSTNAME		canyonlands
 #endif
 #define CONFIG_440		1
 #define CONFIG_4xx		1	/* ... PPC4xx family */
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
 #define CONFIG_SYS_CLK_FREQ	66666667	/* external freq to pll	*/
 
 #define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_early_init_f */
@@ -47,8 +54,6 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0	*/
-
 #define CFG_PCI_MEMBASE		0x80000000	/* mapped PCI memory	*/
 #define CFG_PCI_BASE		0xd0000000	/* internal PCI regs	*/
 #define CFG_PCI_TARGBASE	CFG_PCI_MEMBASE
@@ -86,10 +91,6 @@
 
 #define CFG_AHB_BASE		0xE2000000	/* internal AHB peripherals	*/
 
-#define CFG_MONITOR_BASE	TEXT_BASE
-#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor */
-#define CFG_MALLOC_LEN		(512 * 1024)	/* Reserve 512 kB for malloc()*/
-
 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer (placed in OCM)
  *----------------------------------------------------------------------*/
@@ -102,13 +103,8 @@
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_SERIAL_MULTI	1
 #undef CONFIG_UART1_CONSOLE	/* define this if you want console on UART1 */
 
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
@@ -242,10 +238,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
+#define CFG_I2C_SPEED		400000	/* I2C speed			*/
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR		(0xa8>>1)
@@ -270,7 +263,6 @@
  * Ethernet
  *----------------------------------------------------------------------*/
 #define CONFIG_IBM_EMAC4_V4	1
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address, See schematics	*/
 #define CONFIG_PHY1_ADDR	1
 #define CONFIG_HAS_ETH0
@@ -282,14 +274,11 @@
 #define CONFIG_HAS_ETH2
 #define CONFIG_HAS_ETH3
 #endif
-#define CONFIG_NET_MULTI	1
 
 #define CONFIG_PHY_RESET	1	/* reset phy upon startup	*/
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 #define CONFIG_PHY_DYNAMIC_ANEG	1
 
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
 /*-----------------------------------------------------------------------
  * USB-OHCI
  *----------------------------------------------------------------------*/
@@ -305,104 +294,30 @@
 #define CFG_USB_OHCI_MAX_ROOT_PORTS 15
 #endif
 
-/*-----------------------------------------------------------------------
- * Default environment
- *----------------------------------------------------------------------*/
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifdef CONFIG_CANYONLANDS
-#define CONFIG_HOSTNAME		canyonlands
-#define CFG_BOOTFILE		"bootfile=canyonlands/uImage\0"
-#define CFG_DTBFILE		"fdt_file=canyonlands/canyonlands.dtb\0"
-#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME		glacier
-#define CFG_BOOTFILE		"bootfile=glacier/uImage\0"
-#define CFG_DTBFILE		"fdt_file=glacier/glacier.dtb\0"
-#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	CFG_BOOTFILE							\
-	CFG_DTBFILE							\
-	CFG_ROOTPATH							\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
-	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
-		"tftp ${fdt_addr_r} ${fdt_file}; "			\
-		"run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
-	"kernel_addr_r=400000\0"					\
-	"fdt_addr_r=800000\0"						\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
+	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"fdt_addr=fc1e0000\0"						\
 	"ramdisk_addr=fc200000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 200000 ${hostname}/u-boot.bin\0"			\
-	"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;"	\
-		"cp.b ${fileaddr} fffa0000 ${filesize};"		\
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
-	"nload=tftp 200000 ${hostname}/u-boot-nand.bin\0"		\
-	"nupdate=nand erase 0 100000;nand write 200000 0 100000;"	\
-		"setenv filesize;saveenv\0"				\
-	"nupd=run nload nupdate\0"					\
 	"pciconfighost=1\0"						\
 	"pcie_mode=RP:RP\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE		/* allow baudrate change	*/
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
 #ifdef CONFIG_460EX
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_FAT
@@ -415,41 +330,6 @@
 #define CONFIG_ISO_PARTITION
 
 /*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT		"=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE		256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16	/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_AUTO_COMPLETE	1	/* add autocompletion support	*/
-#define CONFIG_LOOPW		1	/* enable loopw command         */
-#define CONFIG_MX_CYCLIC	1	/* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
-
-#define CFG_HUSH_PARSER		1	/* Use the HUSH parser		*/
-#ifdef	CFG_HUSH_PARSER
-#define	CFG_PROMPT_HUSH_PS2	"> "
-#endif
-
-/*-----------------------------------------------------------------------
  * PCI stuff
  *----------------------------------------------------------------------*/
 /* General PCI */
@@ -465,21 +345,6 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x1014	/* IBM				*/
 #define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever			*/
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
@@ -671,8 +536,4 @@
 }
 #endif
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/ebony.h b/include/configs/ebony.h
index ba68fd4..df444d8 100644
--- a/include/configs/ebony.h
+++ b/include/configs/ebony.h
@@ -35,10 +35,15 @@
 #define CONFIG_440		1	    /* ... PPC440 family	*/
 #define CONFIG_4xx		1	    /* ... PPC4xx family	*/
 #define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_early_init_f	*/
-#undef	CFG_DRAM_TEST			    /* Disable-takes long time! */
 #define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
 
 /*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		ebony
+#include "amcc-common.h"
+
+/*
  * Define here the location of the environment variables (FLASH or NVRAM).
  * Note: DENX encourages to use redundant environment in FLASH. NVRAM is only
  *       supported for backward compatibility.
@@ -55,7 +60,6 @@
  *----------------------------------------------------------------------*/
 #define CFG_SDRAM_BASE	    0x00000000	    /* _must_ be 0		*/
 #define CFG_FLASH_BASE	    0xff800000	    /* start of FLASH		*/
-#define CFG_MONITOR_BASE    0xfffc0000	    /* start of monitor		*/
 #define CFG_PCI_MEMBASE	    0x80000000	    /* mapped pci memory	*/
 #define CFG_PERIPHERAL_BASE 0xe0000000	    /* internal peripherals	*/
 #define CFG_ISRAM_BASE	    0xc0000000	    /* internal SRAM		*/
@@ -74,18 +78,11 @@
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
 #define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
-#define CFG_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
-#define CFG_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
-
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CFG_EXT_SERIAL_CLOCK	(1843200 * 6)	/* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE		115200
-
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400}
 
 /*-----------------------------------------------------------------------
  * NVRAM/RTC
@@ -141,10 +138,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -153,125 +147,31 @@
 #define CFG_EEPROM_PAGE_WRITE_BITS 3
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=ebony\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/ebony/uImage\0"				\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=ff800000\0"					\
 	"ramdisk_addr=ff810000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/ebony/u-boot.bin\0"		        \
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
 
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		8	/* PHY address			*/
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #define CONFIG_PHY1_ADDR	9	/* EMAC1 PHY address		*/
-#define CONFIG_NET_MULTI	1
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SNTP
 
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
@@ -288,28 +188,4 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
 #define CFG_PCI_SUBSYS_DEVICEID 0xcafe  /* Whatever */
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/katmai.h b/include/configs/katmai.h
index cce883f..d3789bd 100644
--- a/include/configs/katmai.h
+++ b/include/configs/katmai.h
@@ -37,8 +37,14 @@
 #define CONFIG_4xx			1	/* ... PPC4xx family	*/
 #define CONFIG_440			1	/* ... PPC440 family	*/
 #define CONFIG_440SPE			1	/* Specifc SPe support	*/
-#undef	CFG_DRAM_TEST				/* Disable-takes long time */
 #define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll	*/
+#define CFG_4xx_RESET_TYPE	0x2	/* use chip reset on this board	*/
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		katmai
+#include "amcc-common.h"
 
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_pre_init		*/
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
@@ -48,7 +54,6 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CFG_FLASH_BASE		0xff000000	/* start of FLASH	*/
 #define CFG_PERIPHERAL_BASE	0xa0000000	/* internal peripherals	*/
 #define CFG_ISRAM_BASE		0x90000000	/* internal SRAM	*/
@@ -78,10 +83,6 @@
 
 #define CFG_ACE_BASE		0xfe000000	/* Xilinx ACE controller - Compact Flash */
 
-#define CFG_MONITOR_BASE	TEXT_BASE
-#define CFG_MONITOR_LEN		(0xFFFFFFFF - CFG_MONITOR_BASE + 1)
-#define CFG_MALLOC_LEN		(512 * 1024)	/* Reserve 512 kB for malloc */
-
 /*-----------------------------------------------------------------------
  * Initial RAM & stack pointer (placed in internal SRAM)
  *----------------------------------------------------------------------*/
@@ -98,12 +99,8 @@
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
-#define CONFIG_SERIAL_MULTI	1
 #undef CONFIG_UART1_CONSOLE
 #undef CFG_EXT_SERIAL_CLOCK
-#define CONFIG_BAUDRATE		115200
-#define CFG_BAUDRATE_TABLE  \
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 
 /*-----------------------------------------------------------------------
  * DDR SDRAM
@@ -117,10 +114,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		100000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
@@ -172,139 +166,36 @@
  *----------------------------------------------------------------------*/
 #define	CFG_ENV_IS_IN_FLASH	1	/* Environment uses flash	*/
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define xstr(s) str(s)
-#define str(s) #s
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=katmai\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-		"bootm\0"						\
-	"net_nfs_fdt=tftp 200000 ${bootfile};"				\
-		"tftp ${fdt_addr} ${fdt_file};"				\
-		"run nfsargs addip addtty;"				\
-		"bootm 200000 - ${fdt_addr}\0"				\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=katmai/uImage\0"					\
-	"fdt_file=katmai/katmai.dtb\0"					\
-	"fdt_addr=400000\0"						\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fff10000\0"					\
 	"ramdisk_addr=fff20000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 200000 katmai/u-boot.bin\0"				\
-	"update=protect off " xstr(CFG_MONITOR_BASE) " FFFFFFFF;"	\
-		"era " xstr(CFG_MONITOR_BASE) " FFFFFFFF;"		\
-		"cp.b ${fileaddr} " xstr(CFG_MONITOR_BASE) " ${filesize};" \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	"kozio=bootm ffc60000\0"					\
 	"pciconfighost=1\0"						\
 	"pcie_mode=RP:RP:RP\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
 
 /*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_EEPROM
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SNTP
 
 #define	CONFIG_IBM_EMAC4_V4	1	/* 440SPe has this EMAC version	*/
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
 #define CONFIG_HAS_ETH0
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup	*/
 #define CONFIG_PHY_RESET_DELAY	1000
 #define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-#define CONFIG_NET_MULTI		/* needed for NetConsole	*/
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP				/* undef to save memory		*/
-#define CFG_PROMPT		"=> "		/* Monitor Command Prompt	*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address		*/
-#define CFG_EXTBDINFO		1		/* To use extended board_into (bd_t) */
-
-#define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
-#define CFG_4xx_RESET_TYPE	0x2	/* use chip reset on this board	*/
 
 /*-----------------------------------------------------------------------
  * FLASH related
@@ -436,28 +327,4 @@
 #define CFG_GPIO_TCR		GPIO_VAL(CFG_GPIO_RS232_FORCEOFF)
 #define CFG_GPIO_ODR		0
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/*Initial Memory map for Linux*/
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02		/* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/kilauea.h b/include/configs/kilauea.h
index a596768..9c1a3a4 100644
--- a/include/configs/kilauea.h
+++ b/include/configs/kilauea.h
@@ -1,4 +1,7 @@
 /*
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ *   Grant Erickson <gerickson@nuovations.com>
+ *
  * (C) Copyright 2007
  * Stefan Roese, DENX Software Engineering, sr@denx.de.
  *
@@ -36,6 +39,12 @@
 #define CONFIG_405EX		1		/* Specifc 405EX support*/
 #define CONFIG_SYS_CLK_FREQ	33333333	/* ext frequency to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		kilauea
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
 #define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
 #define CONFIG_BOARD_EMAC_COUNT
@@ -44,43 +53,70 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0xFC000000
 #define CFG_NAND_ADDR		0xF8000000
 #define CFG_FPGA_BASE		0xF0000000
 #define CFG_PERIPHERAL_BASE	0xEF600000      /* internal peripherals*/
-#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(512 * 1024)	/* Reserve 512 kB for malloc()	*/
-#define CFG_MONITOR_BASE	(TEXT_BASE)
 
 /*-----------------------------------------------------------------------
- * Initial RAM & stack pointer
- *----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR	0x02000000	/* inside of SDRAM	*/
-#define CFG_INIT_RAM_END	(4 << 10)
+ * Initial RAM & Stack Pointer Configuration Options
+ *
+ *   There are traditionally three options for the primordial
+ *   (i.e. initial) stack usage on the 405-series:
+ *
+ *      1) On-chip Memory (OCM) (i.e. SRAM)
+ *      2) Data cache
+ *      3) SDRAM
+ *
+ *   For the 405EX(r), there is no OCM, so we are left with (2) or (3)
+ *   the latter of which is less than desireable since it requires
+ *   setting up the SDRAM and ECC in assembly code.
+ *
+ *   To use (2), define 'CFG_INIT_DCACHE_CS' to be an unused chip
+ *   select on the External Bus Controller (EBC) and then select a
+ *   value for 'CFG_INIT_RAM_ADDR' outside of the range of valid,
+ *   physical SDRAM. Otherwise, undefine 'CFG_INIT_DCACHE_CS' and
+ *   select a value for 'CFG_INIT_RAM_ADDR' within the range of valid,
+ *   physical SDRAM to use (3).
+ *-----------------------------------------------------------------------*/
+
+#define CFG_INIT_DCACHE_CS	4
+
+#if defined(CFG_INIT_DCACHE_CS)
+#define CFG_INIT_RAM_ADDR	(CFG_SDRAM_BASE + ( 1 << 30))	/*  1 GiB */
+#else
+#define CFG_INIT_RAM_ADDR	(CFG_SDRAM_BASE + (32 << 20))	/* 32 MiB */
+#endif /* defined(CFG_INIT_DCACHE_CS) */
+
+#define CFG_INIT_RAM_END        (4 << 10)			/*  4 KiB */
 #define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-/* reserve some memory for POST and BOOT limit info */
-#define CFG_INIT_SP_OFFSET	(CFG_GBL_DATA_OFFSET - 16)
 
-/* extra data in init-ram */
-#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 4)
-#define CFG_POST_MAGIC		(CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8)
-#define CFG_POST_VAL		(CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12)
-#define CFG_OCM_DATA_ADDR	CFG_INIT_RAM_ADDR /* for commproc.c	*/
+/*
+ * If the data cache is being used for the primordial stack and global
+ * data area, the POST word must be placed somewhere else. The General
+ * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
+ * its compare and mask register contents across reset, so it is used
+ * for the POST word.
+ */
+
+#if defined(CFG_INIT_DCACHE_CS)
+# define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+# define CFG_POST_ALT_WORD_ADDR	(CFG_PERIPHERAL_BASE + GPT0_COMP6)
+#else
+# define CFG_INIT_EXTRA_SIZE	16
+# define CFG_INIT_SP_OFFSET	(CFG_GBL_DATA_OFFSET - CFG_INIT_EXTRA_SIZE)
+# define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 4)
+# define CFG_OCM_DATA_ADDR	CFG_INIT_RAM_ADDR
+#endif /* defined(CFG_INIT_DCACHE_CS) */
 
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CFG_EXT_SERIAL_CLOCK	11059200	/* ext. 11.059MHz clk	*/
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_SERIAL_MULTI     1
 /* define this if you want console on UART1 */
 #undef CONFIG_UART1_CONSOLE
 
-#define CFG_BAUDRATE_TABLE						\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
@@ -131,9 +167,9 @@
  * This NAND U-Boot (NUB) is a special U-Boot version which can be started
  * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
  *
- * On 440EPx the SPL is copied to SDRAM before the NAND controller is
- * set up. While still running from cache, I experienced problems accessing
- * the NAND controller.	sr - 2006-08-25
+ * On 405EX the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from location 0xfffff000...0xffffffff the
+ * NAND controller cannot be accessed since it is attached to CS0 too.
  */
 #define CFG_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location			*/
 #define CFG_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size			*/
@@ -187,12 +223,54 @@
  *----------------------------------------------------------------------*/
 #define CFG_MBYTES_SDRAM        (256)		/* 256MB			*/
 
+#define	CFG_SDRAM0_MB0CF_BASE	((  0 << 20) + CFG_SDRAM_BASE)
+
+/* DDR1/2 SDRAM Device Control Register Data Values */
+#define CFG_SDRAM0_MB0CF	((CFG_SDRAM0_MB0CF_BASE >> 3)	| \
+				 SDRAM_RXBAS_SDSZ_256MB		| \
+				 SDRAM_RXBAS_SDAM_MODE7		| \
+				 SDRAM_RXBAS_SDBE_ENABLE)
+#define CFG_SDRAM0_MB1CF	SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MB2CF	SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MB3CF	SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MCOPT1	0x04322000
+#define CFG_SDRAM0_MCOPT2	0x00000000
+#define CFG_SDRAM0_MODT0	0x01800000
+#define CFG_SDRAM0_MODT1	0x00000000
+#define CFG_SDRAM0_CODT		0x0080f837
+#define CFG_SDRAM0_RTR		0x06180000
+#define CFG_SDRAM0_INITPLR0	0xa8380000
+#define CFG_SDRAM0_INITPLR1	0x81900400
+#define CFG_SDRAM0_INITPLR2	0x81020000
+#define CFG_SDRAM0_INITPLR3	0x81030000
+#define CFG_SDRAM0_INITPLR4	0x81010404
+#define CFG_SDRAM0_INITPLR5	0x81000542
+#define CFG_SDRAM0_INITPLR6	0x81900400
+#define CFG_SDRAM0_INITPLR7	0x8D080000
+#define CFG_SDRAM0_INITPLR8	0x8D080000
+#define CFG_SDRAM0_INITPLR9	0x8D080000
+#define CFG_SDRAM0_INITPLR10	0x8D080000
+#define CFG_SDRAM0_INITPLR11	0x81000442
+#define CFG_SDRAM0_INITPLR12	0x81010780
+#define CFG_SDRAM0_INITPLR13	0x81010400
+#define CFG_SDRAM0_INITPLR14	0x00000000
+#define CFG_SDRAM0_INITPLR15	0x00000000
+#define CFG_SDRAM0_RQDC		0x80000038
+#define CFG_SDRAM0_RFDC		0x00000209
+#define CFG_SDRAM0_RDCC		0x40000000
+#define CFG_SDRAM0_DLCR		0x030000a5
+#define CFG_SDRAM0_CLKTR	0x80000000
+#define CFG_SDRAM0_WRDTR	0x00000000
+#define CFG_SDRAM0_SDTR1	0x80201000
+#define CFG_SDRAM0_SDTR2	0x32204232
+#define CFG_SDRAM0_SDTR3	0x080b0d1a
+#define CFG_SDRAM0_MMODE	0x00000442
+#define CFG_SDRAM0_MEMODE	0x00000404
+
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	6	/* 24C02 requires 5ms delay */
 #define CFG_I2C_EEPROM_ADDR	0x52	/* I2C boot EEPROM (24C02BN)	*/
@@ -212,7 +290,6 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_M88E1111_PHY	1
 #define CONFIG_IBM_EMAC4_V4	1
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
 
 #define CONFIG_PHY_RESET	1	/* reset phy upon startup	*/
@@ -220,107 +297,37 @@
 
 #define CONFIG_HAS_ETH0		1
 
-#define CONFIG_NET_MULTI	1
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
 #define CONFIG_PHY1_ADDR	2
 
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
+	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"logversion=2\0"						\
-	"netdev=eth0\0"							\
-	"hostname=kilauea\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_self_old=run ramargs addip addtty;"			\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
-	"flash_nfs_old=run nfsargs addip addtty;"			\
-		"bootm ${kernel_addr}\0"				\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
-	"net_nfs_old=tftp ${kernel_addr_r} ${bootfile};"		\
-		"run nfsargs addip addtty;bootm ${kernel_addr_r}\0"	\
-	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
-		"tftp ${fdt_addr_r} ${fdt_file}; "			\
-		"run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=kilauea/uImage\0"					\
-	"fdt_file=kilauea/kilauea.dtb\0"				\
-	"kernel_addr_r=400000\0"					\
-	"fdt_addr_r=800000\0"						\
 	"kernel_addr=fc000000\0"					\
 	"fdt_addr=fc1e0000\0"						\
 	"ramdisk_addr=fc200000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 200000 kilauea/u-boot.bin\0"				\
-	"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;"	\
-		"cp.b ${fileaddr} fffa0000 ${filesize};"		\
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
-	"nload=tftp 200000 kilauea/u-boot-nand.bin\0"			\
-	"nupdate=nand erase 0 60000;nand write 200000 0 60000;"		\
-		"setenv filesize;saveenv\0"				\
-	"nupd=run nload nupdate\0"					\
 	"pciconfighost=1\0"						\
 	"pcie_mode=RP:RP\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE		/* allow baudrate change	*/
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
 #define CONFIG_CMD_LOG
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SNTP
 
 /* POST support */
-#define CONFIG_POST		(CFG_POST_MEMORY	| \
-				 CFG_POST_CACHE		| \
+#define CONFIG_POST		(CFG_POST_CACHE		| \
 				 CFG_POST_CPU		| \
 				 CFG_POST_ETHER		| \
 				 CFG_POST_I2C		| \
@@ -335,37 +342,6 @@
 
 #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
 
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
-
 /*-----------------------------------------------------------------------
  * PCI stuff
  *----------------------------------------------------------------------*/
@@ -394,13 +370,6 @@
 /* base address of inbound PCIe window */
 #define CFG_PCIE_INBOUND_BASE	0x0000000000000000ULL
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
@@ -429,7 +398,7 @@
 
 /* Memory Bank 2 (FPGA) initialization						*/
 #define CFG_EBC_PB2AP           0x9400C800
-#define CFG_EBC_PB2CR           0xF0018000 /*  BAS=0x800,BS=1MB,BU=R/W,BW=8bit	*/
+#define CFG_EBC_PB2CR		(CFG_FPGA_BASE | 0x18000)
 
 #define CFG_EBC_CFG		0x7FC00000 /*  EBC0_CFG */
 
@@ -474,19 +443,6 @@
 }												\
 }
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
 /*-----------------------------------------------------------------------
  * Some Kilauea stuff..., mainly fpga registers
  */
@@ -522,8 +478,4 @@
 #define CFG_FPGA_USER_LED0		0x00000200
 #define CFG_FPGA_USER_LED1		0x00000100
 
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/luan.h b/include/configs/luan.h
index 37151d3..805cc59 100644
--- a/include/configs/luan.h
+++ b/include/configs/luan.h
@@ -37,6 +37,12 @@
 #define CONFIG_440		1
 #define CONFIG_SYS_CLK_FREQ	33333333 /* external freq to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		luan
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
 
@@ -44,11 +50,6 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc  */
-#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
-#define CFG_SDRAM_BASE	        0x00000000	/* MUST be zero */
-
 #define CFG_LARGE_FLASH		0xffc00000	/* 4MB flash address CS0 */
 #define CFG_SMALL_FLASH		0xff900000	/* 1MB flash address CS2 */
 #define CFG_SRAM_BASE		0xff800000	/* 1MB SRAM  address CS2 */
@@ -68,7 +69,6 @@
 #define CFG_FLASH_BASE		CFG_SMALL_FLASH
 #endif
 
-#undef CFG_DRAM_TEST
 #if CFG_SRAM_BASE
 #define CFG_KBYTES_SDRAM	1024*2
 #else
@@ -88,13 +88,8 @@
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CFG_EXT_SERIAL_CLOCK	11059200 /* external 11.059MHz clk */
-#define CONFIG_BAUDRATE		115200
-#undef  CONFIG_SERIAL_MULTI
 #undef  CONFIG_UART1_CONSOLE		/* define if you want console on UART1 */
 
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
@@ -139,10 +134,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -151,61 +143,22 @@
 #define CFG_EEPROM_PAGE_WRITE_BITS 3
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=luan\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=$(serverip):$(rootpath)\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs $(bootargs) "				\
-		"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)"	\
-		":$(hostname):$(netdev):off panic=1\0"			\
-	"addtty=setenv bootargs $(bootargs) console=ttyS0,$(baudrate)\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm $(kernel_addr)\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm $(kernel_addr) $(ramdisk_addr)\0"		\
-	"net_nfs=tftp 200000 $(bootfile);run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/luan/uImage\0"				\
+/*
+ * Default environment variables
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_PPC						\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"ramdisk_addr=fc100000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/luan/u-boot.bin\0"			\
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_HAS_ETH0
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1
 #define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-#define CONFIG_NET_MULTI		/* needed for NetConsole	*/
-
 #ifdef DEBUG
 #define CONFIG_PANIC_HANG
 #else
@@ -213,60 +166,11 @@
 #endif
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on	        */
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000 /* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-#undef  CONFIG_LYNXKDI			/* support kdi files            */
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
@@ -287,28 +191,4 @@
 
 #endif
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/makalu.h b/include/configs/makalu.h
index af066f3..65b240e 100644
--- a/include/configs/makalu.h
+++ b/include/configs/makalu.h
@@ -1,4 +1,7 @@
 /*
+ * Copyright (c) 2008 Nuovation System Designs, LLC
+ *   Grant Erickson <gerickson@nuovations.com>
+ *
  * (C) Copyright 2007-2008
  * Stefan Roese, DENX Software Engineering, sr@denx.de.
  *
@@ -36,6 +39,13 @@
 #define CONFIG_405EX		1		/* Specifc 405EX support*/
 #define CONFIG_SYS_CLK_FREQ	33330000	/* ext frequency to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME	makalu
+#define CONFIG_ADDMISC	"addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0"
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1		/* Call board_early_init_f */
 #define CONFIG_MISC_INIT_R	1		/* Call misc_init_r	*/
 
@@ -43,42 +53,69 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0xFC000000
 #define CFG_FPGA_BASE		0xF0000000
 #define CFG_PERIPHERAL_BASE	0xEF600000      /* internal peripherals*/
-#define CFG_MONITOR_LEN		(384 * 1024)	/* Reserve 384 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(512 * 1024)	/* Reserve 512 kB for malloc()	*/
-#define CFG_MONITOR_BASE	(TEXT_BASE)
 
 /*-----------------------------------------------------------------------
- * Initial RAM & stack pointer
- *----------------------------------------------------------------------*/
-#define CFG_INIT_RAM_ADDR	0x02000000	/* inside of SDRAM	*/
-#define CFG_INIT_RAM_END	(4 << 10)
+ * Initial RAM & Stack Pointer Configuration Options
+ *
+ *   There are traditionally three options for the primordial
+ *   (i.e. initial) stack usage on the 405-series:
+ *
+ *      1) On-chip Memory (OCM) (i.e. SRAM)
+ *      2) Data cache
+ *      3) SDRAM
+ *
+ *   For the 405EX(r), there is no OCM, so we are left with (2) or (3)
+ *   the latter of which is less than desireable since it requires
+ *   setting up the SDRAM and ECC in assembly code.
+ *
+ *   To use (2), define 'CFG_INIT_DCACHE_CS' to be an unused chip
+ *   select on the External Bus Controller (EBC) and then select a
+ *   value for 'CFG_INIT_RAM_ADDR' outside of the range of valid,
+ *   physical SDRAM. Otherwise, undefine 'CFG_INIT_DCACHE_CS' and
+ *   select a value for 'CFG_INIT_RAM_ADDR' within the range of valid,
+ *   physical SDRAM to use (3).
+ *-----------------------------------------------------------------------*/
+
+#define CFG_INIT_DCACHE_CS	4
+
+#if defined(CFG_INIT_DCACHE_CS)
+#define CFG_INIT_RAM_ADDR	(CFG_SDRAM_BASE + ( 1 << 30))	/*  1 GiB */
+#else
+#define CFG_INIT_RAM_ADDR	(CFG_SDRAM_BASE + (32 << 20))	/* 32 MiB */
+#endif /* defined(CFG_INIT_DCACHE_CS) */
+
+#define CFG_INIT_RAM_END        (4 << 10)			/*  4 KiB */
 #define CFG_GBL_DATA_SIZE	256		/* num bytes initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-/* reserve some memory for POST and BOOT limit info */
-#define CFG_INIT_SP_OFFSET	(CFG_GBL_DATA_OFFSET - 16)
 
-/* extra data in init-ram */
-#define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 4)
-#define CFG_POST_MAGIC		(CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 8)
-#define CFG_POST_VAL		(CFG_INIT_RAM_ADDR + CFG_GBL_DATA_OFFSET - 12)
-#define CFG_OCM_DATA_ADDR	CFG_INIT_RAM_ADDR /* for commproc.c	*/
+/*
+ * If the data cache is being used for the primordial stack and global
+ * data area, the POST word must be placed somewhere else. The General
+ * Purpose Timer (GPT) is unused by u-boot and the kernel and preserves
+ * its compare and mask register contents across reset, so it is used
+ * for the POST word.
+ */
+
+#if defined(CFG_INIT_DCACHE_CS)
+# define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+# define CFG_POST_ALT_WORD_ADDR	(CFG_PERIPHERAL_BASE + GPT0_COMP6)
+#else
+# define CFG_INIT_EXTRA_SIZE	16
+# define CFG_INIT_SP_OFFSET	(CFG_GBL_DATA_OFFSET - CFG_INIT_EXTRA_SIZE)
+# define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 4)
+# define CFG_OCM_DATA_ADDR	CFG_INIT_RAM_ADDR
+#endif /* defined(CFG_INIT_DCACHE_CS) */
 
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #undef CFG_EXT_SERIAL_CLOCK			/* no ext. clk		*/
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_SERIAL_MULTI     1
 /* define this if you want console on UART1 */
 #undef CONFIG_UART1_CONSOLE
 
-#define CFG_BAUDRATE_TABLE						\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
@@ -113,14 +150,60 @@
 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
-#define CFG_MBYTES_SDRAM	256
+#define CFG_MBYTES_SDRAM        (256)		/* 256MB			*/
+
+#define	CFG_SDRAM0_MB0CF_BASE	((  0 << 20) + CFG_SDRAM_BASE)
+#define	CFG_SDRAM0_MB1CF_BASE	((128 << 20) + CFG_SDRAM_BASE)
+
+/* DDR1/2 SDRAM Device Control Register Data Values */
+#define CFG_SDRAM0_MB0CF	((CFG_SDRAM0_MB0CF_BASE >> 3)	| \
+				 SDRAM_RXBAS_SDSZ_128MB 	| \
+				 SDRAM_RXBAS_SDAM_MODE2 	| \
+				 SDRAM_RXBAS_SDBE_ENABLE)
+#define CFG_SDRAM0_MB1CF	((CFG_SDRAM0_MB1CF_BASE >> 3)	| \
+				 SDRAM_RXBAS_SDSZ_128MB 	| \
+				 SDRAM_RXBAS_SDAM_MODE2 	| \
+				 SDRAM_RXBAS_SDBE_ENABLE)
+#define CFG_SDRAM0_MB2CF	SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MB3CF	SDRAM_RXBAS_SDBE_DISABLE
+#define CFG_SDRAM0_MCOPT1	0x04322000
+#define CFG_SDRAM0_MCOPT2	0x00000000
+#define CFG_SDRAM0_MODT0	0x01800000
+#define CFG_SDRAM0_MODT1	0x00000000
+#define CFG_SDRAM0_CODT		0x0080f837
+#define CFG_SDRAM0_RTR		0x06180000
+#define CFG_SDRAM0_INITPLR0	0xa8380000
+#define CFG_SDRAM0_INITPLR1	0x81900400
+#define CFG_SDRAM0_INITPLR2	0x81020000
+#define CFG_SDRAM0_INITPLR3	0x81030000
+#define CFG_SDRAM0_INITPLR4	0x81010404
+#define CFG_SDRAM0_INITPLR5	0x81000542
+#define CFG_SDRAM0_INITPLR6	0x81900400
+#define CFG_SDRAM0_INITPLR7	0x8D080000
+#define CFG_SDRAM0_INITPLR8	0x8D080000
+#define CFG_SDRAM0_INITPLR9	0x8D080000
+#define CFG_SDRAM0_INITPLR10	0x8D080000
+#define CFG_SDRAM0_INITPLR11	0x81000442
+#define CFG_SDRAM0_INITPLR12	0x81010780
+#define CFG_SDRAM0_INITPLR13	0x81010400
+#define CFG_SDRAM0_INITPLR14	0x00000000
+#define CFG_SDRAM0_INITPLR15	0x00000000
+#define CFG_SDRAM0_RQDC		0x80000038
+#define CFG_SDRAM0_RFDC		0x00000209
+#define CFG_SDRAM0_RDCC		0x40000000
+#define CFG_SDRAM0_DLCR		0x030000a5
+#define CFG_SDRAM0_CLKTR	0x80000000
+#define CFG_SDRAM0_WRDTR	0x00000000
+#define CFG_SDRAM0_SDTR1	0x80201000
+#define CFG_SDRAM0_SDTR2	0x32204232
+#define CFG_SDRAM0_SDTR3	0x080b0d1a
+#define CFG_SDRAM0_MMODE	0x00000442
+#define CFG_SDRAM0_MEMODE	0x00000404
 
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	6	/* 24C02 requires 5ms delay */
 #define CFG_I2C_EEPROM_ADDR	0x52	/* I2C boot EEPROM (24C02BN)	*/
@@ -140,7 +223,6 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_M88E1111_PHY	1
 #define CONFIG_IBM_EMAC4_V4	1
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		6	/* PHY address, See schematics	*/
 
 #define CONFIG_PHY_RESET	1	/* reset phy upon startup	*/
@@ -148,104 +230,35 @@
 
 #define CONFIG_HAS_ETH0		1
 
-#define CONFIG_NET_MULTI	1
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"   */
 #define CONFIG_PHY1_ADDR	0
 
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"logversion=2\0"						\
-	"netdev=eth0\0"							\
-	"hostname=makalu\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"addmisc=setenv bootargs ${bootargs} rtc-x1205.probe=0,0x6f\0"	\
-	"flash_self_old=run ramargs addip addtty addmisc;"		\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"flash_self=run ramargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0"	\
-	"flash_nfs_old=run nfsargs addip addtty addmisc;"		\
-		"bootm ${kernel_addr}\0"				\
-	"flash_nfs=run nfsargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr} - ${fdt_addr}\0"			\
-	"net_nfs_old=tftp ${kernel_addr_r} ${bootfile};"		\
-		"run nfsargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr_r}\0"				\
-	"net_nfs=tftp ${kernel_addr_r} ${bootfile}; "			\
-		"tftp ${fdt_addr_r} ${fdt_file}; "			\
-		"run nfsargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=makalu/uImage\0"					\
-	"fdt_file=makalu/makalu.dtb\0"					\
-	"kernel_addr_r=400000\0"					\
-	"fdt_addr_r=800000\0"						\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"fdt_addr=fc1e0000\0"						\
 	"ramdisk_addr=fc200000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 200000 makalu/u-boot.bin\0"				\
-	"update=protect off fffa0000 ffffffff;era fffa0000 ffffffff;"	\
-		"cp.b ${fileaddr} fffa0000 ${filesize};"		\
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	"pciconfighost=1\0"						\
 	"pcie_mode=RP:RP\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE		/* allow baudrate change	*/
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
 #define CONFIG_CMD_LOG
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SNTP
 
 /* POST support */
-#define CONFIG_POST		(CFG_POST_MEMORY	| \
-				 CFG_POST_CACHE		| \
+#define CONFIG_POST		(CFG_POST_CACHE		| \
 				 CFG_POST_CPU		| \
 				 CFG_POST_ETHER		| \
 				 CFG_POST_I2C		| \
@@ -260,37 +273,6 @@
 
 #define CFG_CONSOLE_IS_IN_ENV /* Otherwise it catches logbuffer as output */
 
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
-
 /*-----------------------------------------------------------------------
  * PCI stuff
  *----------------------------------------------------------------------*/
@@ -319,13 +301,6 @@
 /* base address of inbound PCIe window */
 #define CFG_PCIE_INBOUND_BASE	0x0000000000000000ULL
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
@@ -384,21 +359,4 @@
 #define CFG_GPIO_PCIE_CLKREQ	27
 #define CFG_GPIO_PCIE_WAKE	28
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h
index be2b3ec..407aae7 100644
--- a/include/configs/ocotea.h
+++ b/include/configs/ocotea.h
@@ -44,16 +44,19 @@
 #define CONFIG_440		1	    /* ... PPC440 family	*/
 #define CONFIG_4xx		1	    /* ... PPC4xx family	*/
 #define CONFIG_BOARD_EARLY_INIT_F 1	    /* Call board_pre_init	*/
-#undef	CFG_DRAM_TEST			    /* Disable-takes long time! */
 #define CONFIG_SYS_CLK_FREQ	33333333    /* external freq to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		ocotea
+#include "amcc-common.h"
+
 /*-----------------------------------------------------------------------
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE	    0x00000000	    /* _must_ be 0		*/
 #define CFG_FLASH_BASE	    0xff800000	    /* start of FLASH		*/
-#define CFG_MONITOR_BASE    0xfffc0000	    /* start of monitor		*/
 #define CFG_PCI_MEMBASE	    0x80000000	    /* mapped pci memory	*/
 #define CFG_PERIPHERAL_BASE 0xe0000000	    /* internal peripherals	*/
 #define CFG_ISRAM_BASE	    0xc0000000	    /* internal SRAM		*/
@@ -75,18 +78,11 @@
 #define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
 #define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
 
-#define CFG_MONITOR_LEN	    (256 * 1024)    /* Reserve 256 kB for Mon	*/
-#define CFG_MALLOC_LEN	    (128 * 1024)    /* Reserve 128 kB for malloc*/
-
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #define CFG_EXT_SERIAL_CLOCK	(1843200 * 6)	/* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE		115200
-
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 
 /*-----------------------------------------------------------------------
  * Environment
@@ -156,10 +152,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -168,54 +161,17 @@
 #define CFG_EEPROM_PAGE_WRITE_BITS 3
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=ocotea\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/ocotea/uImage\0"				\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_PPC						\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fff00000\0"					\
 	"ramdisk_addr=fff10000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/ocotea/u-boot.bin\0"		\
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
 
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_NET_MULTI	1
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
 #define CONFIG_PHY1_ADDR	2
 #define CONFIG_PHY2_ADDR	0x10
@@ -228,73 +184,15 @@
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 #define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
 #define CONFIG_PHY_RESET_DELAY	1000
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SNTP
 
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
@@ -311,28 +209,4 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
 #define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/sequoia.h b/include/configs/sequoia.h
index 48251f3..f4eefae 100644
--- a/include/configs/sequoia.h
+++ b/include/configs/sequoia.h
@@ -34,11 +34,19 @@
 /* This config file is used for Sequoia (440EPx) and Rainier (440GRx)	*/
 #ifndef CONFIG_RAINIER
 #define CONFIG_440EPX		1	/* Specific PPC440EPx		*/
+#define CONFIG_HOSTNAME		sequoia
 #else
 #define CONFIG_440GRX		1	/* Specific PPC440GRx		*/
+#define CONFIG_HOSTNAME		rainier
 #endif
 #define CONFIG_440		1	/* ... PPC440 family		*/
 #define CONFIG_4xx		1	/* ... PPC4xx family		*/
+
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
 /* Detect Sequoia PLL input clock automatically via CPLD bit		*/
 #define CONFIG_SYS_CLK_FREQ    ((in8(CFG_BCSR_BASE + 3) & 0x80) ? \
 				33333333 : 33000000)
@@ -64,19 +72,9 @@
  * Base addresses -- Note these are effective addresses where the actual
  * resources get mapped (not physical addresses).
  */
-#ifndef CONFIG_VIDEO
-#define CFG_MONITOR_LEN		(384 * 1024) /* Reserve 384 kiB for Monitor  */
-#define CFG_MALLOC_LEN		(256 * 1024) /* Reserve 256 kiB for malloc() */
-#else
-#define CFG_MONITOR_LEN		(512 * 1024)    /* Reserve 512 kB for Monitor   */
-#define CFG_MALLOC_LEN		(1024 * 1024)   /* Reserve 1024 kB for malloc() */
-#endif
-
 #define CFG_TLB_FOR_BOOT_FLASH	0x0003
 #define CFG_BOOT_BASE_ADDR	0xf0000000
-#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CFG_FLASH_BASE		0xfc000000	/* start of FLASH	*/
-#define CFG_MONITOR_BASE	TEXT_BASE
 #define CFG_NAND_ADDR		0xd0000000	/* NAND Flash		*/
 #define CFG_OCM_BASE		0xe0010000	/* ocm			*/
 #define CFG_OCM_DATA_ADDR	CFG_OCM_BASE
@@ -108,14 +106,9 @@
  * Serial Port
  */
 #define CFG_EXT_SERIAL_CLOCK	11059200	/* ext. 11.059MHz clk	*/
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_SERIAL_MULTI	1
 /* define this if you want console on UART1 */
 #undef CONFIG_UART1_CONSOLE
 
-#define CFG_BAUDRATE_TABLE						\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*
  * Environment
  */
@@ -227,10 +220,7 @@
 /*
  * I2C
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -247,80 +237,27 @@
 #define CFG_DTT_LOW_TEMP	-30
 #define CFG_DTT_HYSTERESIS	3
 
-#define CONFIG_PREBOOT	"echo;"						\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifndef CONFIG_RAINIER
-#define CONFIG_HOSTNAME		sequoia
-#define CFG_BOOTFILE		"bootfile=sequoia/uImage\0"
-#define CFG_DTBFILE		"fdt_file=sequoia/sequoia.dtb\0"
-#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME		rainier
-#define CFG_BOOTFILE		"bootfile=rainier/uImage\0"
-#define CFG_DTBFILE		"fdt_file=rainier/rainier.dtb\0"
-#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	CFG_BOOTFILE							\
-	CFG_ROOTPATH							\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"addmisc=setenv bootargs ${bootargs}\0"				\
-	"flash_nfs=run nfsargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty addmisc;"			\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};"				\
-		"run nfsargs addip addtty addmisc;"			\
-		"bootm\0"						\
-	"fdt_file=sequoia/sequoia.dtb\0"				\
-	"fdt_addr=400000\0"						\
-	"net_nfs_fdt=tftp 200000 ${bootfile};"				\
-		"tftp ${fdt_addr} ${fdt_file};"				\
-		"run nfsargs addip addtty addmisc;"			\
-		"bootm 200000 - ${fdt_addr}\0"				\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
+	CONFIG_AMCC_DEF_ENV_NAND_UPD					\
 	"kernel_addr=FC000000\0"					\
 	"ramdisk_addr=FC180000\0"					\
-	"load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0"		\
-	"update=protect off FFFA0000 FFFFFFFF;era FFFA0000 FFFFFFFF;"	\
-		"cp.b 200000 FFFA0000 60000\0"			        \
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_M88E1111_PHY	1
 #define	CONFIG_IBM_EMAC4_V4	1
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0	/* PHY address, See schematics	*/
 
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup	*/
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 
 #define CONFIG_HAS_ETH0
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx	*/
-					/*   buffers & descriptors	*/
-#define CONFIG_NET_MULTI	1
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
 #define CONFIG_PHY1_ADDR	1
 
@@ -347,35 +284,12 @@
 #define CONFIG_ISO_PARTITION
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-#define CONFIG_BOOTP_SUBNETMASK
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
 #define CONFIG_CMD_FAT
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
 #define CONFIG_CMD_NAND
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 
 #ifdef CONFIG_440EPX
@@ -407,35 +321,6 @@
 #define CONFIG_SUPPORT_VFAT
 
 /*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)
-					/* Print Buffer Size		*/
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
-#define CFG_EXTBDINFO		1  /* To use extended board_into (bd_t)	*/
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW		1	/* enable loopw command		*/
-#define CONFIG_MX_CYCLIC	1	/* enable mdc/mwc commands	*/
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable	*/
-
-/*
  * PCI stuff
  */
 /* General PCI */
@@ -453,13 +338,6 @@
 #define CFG_PCI_SUBSYS_ID       0xcafe	/* Whatever			*/
 
 /*
- * For booting Linux, the board info and command line data have to be in the
- * first 8 MB of memory, since this is the maximum mapped by the Linux kernel
- * during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20) /* Initial Memory map for Linux */
-
-/*
  * External Bus Controller (EBC) Setup
  */
 
@@ -577,23 +455,6 @@
 }											\
 }
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01	/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02	/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400 /* speed to run kgdb serial port	*/
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use	*/
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #ifdef CONFIG_VIDEO
 #define CONFIG_BIOSEMU			/* x86 bios emulator for vga bios */
 #define CONFIG_ATI_RADEON_FB		/* use radeon framebuffer driver */
diff --git a/include/configs/taihu.h b/include/configs/taihu.h
index c060b1e..86f776d 100644
--- a/include/configs/taihu.h
+++ b/include/configs/taihu.h
@@ -32,6 +32,12 @@
 #define CONFIG_4xx		1	/*  member of PPC4xx family */
 #define CONFIG_TAIHU	        1	/*  on a taihu board */
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		taihu
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f */
 
 #define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
@@ -70,87 +76,31 @@
 
 #define CFG_ENV_IS_IN_FLASH     1	/* use FLASH for environment vars */
 
-#define CONFIG_ENV_OVERWRITE 1
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"bootfile=/tftpboot/taihu/uImage\0"				\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"netdev=eth0\0"							\
-	"hostname=taihu\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
+/*
+ * Default environment variables
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_PPC						\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=FC000000\0"					\
 	"ramdisk_addr=FC180000\0"					\
-	"load=tftp 200000 /tftpboot/taihu/u-boot.bin\0"			\
-	"update=protect off FFFC0000 FFFFFFFF;era FFFC0000 FFFFFFFF;"	\
-		"cp.b 200000 FFFC0000 40000\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
 
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0x14	/* PHY address			*/
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #define CONFIG_PHY1_ADDR	0x10	/* EMAC1 PHY address		*/
-#define CONFIG_NET_MULTI	1
-#define CFG_RX_ETH_BUFFER	16	/* Number of ethernet rx buffers & descriptors */
 #define CONFIG_PHY_RESET	1
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_CACHE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SPI
 
-#undef CONFIG_WATCHDOG			/* watchdog disabled */
-
 #undef CONFIG_SPD_EEPROM		/* use SPD EEPROM for setup */
 #define CFG_SDRAM_SIZE_PER_BANK 0x04000000 /* 64MB */
 #define CFG_SDRAM_BANKS	        2
@@ -169,23 +119,6 @@
 #define CFG_SDRAM_tRFC		66	/* Auto refresh period */
 
 /*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* print buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START  0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END	   0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-/*
  * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
  * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
  * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
@@ -198,35 +131,13 @@
 #undef  CFG_EXT_SERIAL_CLOCK           /* external serial clock */
 #undef  CFG_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */
 #define CFG_BASE_BAUD		691200
-
-#define CONFIG_BAUDRATE		115200
-
 #define CONFIG_UART1_CONSOLE	1
 
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR	    0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ			1000	/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
-
 /*-----------------------------------------------------------------------
  * I2C stuff
  *-----------------------------------------------------------------------
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef  CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_NOPROBES	{ 0x69 } /* avoid iprobe hangup (why?) */
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	6 /* 24C02 requires 5ms delay */
@@ -278,25 +189,12 @@ unsigned char spi_read(void);
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0xFFE00000
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
-#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-
 #define CFG_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
 #define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
@@ -421,21 +319,5 @@ unsigned char spi_read(void);
 
 #define CPLD_REG0_ADDR	0x50100000
 #define CPLD_REG1_ADDR	0x50100001
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02		/* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
 
 #endif	/* __CONFIG_H */
diff --git a/include/configs/taishan.h b/include/configs/taishan.h
index 1879d38..ba42192 100644
--- a/include/configs/taishan.h
+++ b/include/configs/taishan.h
@@ -32,9 +32,15 @@
 #define CONFIG_440GX		1	/* Specifc GX support		*/
 #define CONFIG_440		1	/* ... PPC440 family		*/
 #define CONFIG_4xx		1	/* ... PPC4xx family		*/
-#undef	CFG_DRAM_TEST			/* Disable-takes long time!	*/
 #define CONFIG_SYS_CLK_FREQ	33333333 /* external freq to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		taishan
+#define CONFIG_USE_TTY		ttyS1
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_pre_init		*/
 #define CONFIG_MISC_INIT_R	1	/* Call misc_init_r		*/
 
@@ -42,9 +48,7 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CFG_FLASH_BASE		0xfc000000	/* start of FLASH	*/
-#define CFG_MONITOR_BASE	0xfffc0000	/* start of monitor	*/
 #define CFG_PCI_MEMBASE		0x80000000	/* mapped pci memory	*/
 #define CFG_PERIPHERAL_BASE	0xe0000000	/* internal peripherals	*/
 #define CFG_ISRAM_BASE		0xc0000000	/* internal SRAM	*/
@@ -70,19 +74,11 @@
 #define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
 #define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
 
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon*/
-#define CFG_MALLOC_LEN		(1024 * 1024)	/* Reserve 1024 kB for malloc*/
-
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CONFIG_UART1_CONSOLE	1	/* use of UART1 as console	*/
-#define CONFIG_SERIAL_MULTI     1	/* enable serial multi support	*/
 #define CFG_EXT_SERIAL_CLOCK	(1843200 * 6)	/* Ext clk @ 11.059 MHz */
-#define CONFIG_BAUDRATE		115200
-
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
 
 /*-----------------------------------------------------------------------
  * Environment
@@ -138,10 +134,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #undef CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	0x50
@@ -159,65 +152,23 @@
 #define CFG_DTT_LOW_TEMP	-30
 #define CFG_DTT_HYSTERESIS	3
 
-/*-----------------------------------------------------------------------
- * Environment
- *----------------------------------------------------------------------*/
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=taishan\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS1,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/taishan/uImage\0"				\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"ramdisk_addr=fc180000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/taishan/u-boot.bin\0"		\
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
-	"fixedip=setenv bootargs $(bootargs) ip=$(ipaddr):$(serverip):" \
-	"$(gatewayip):$(netmask):$(hostname):$(netdev):off panic=1\0"	\
-	"dhcp=setenv bootargs $(bootargs) ip=dhcp\0"			\
 	"kozio=bootm 0xffe00000\0"					\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 /*-----------------------------------------------------------------------
  * Networking
  *----------------------------------------------------------------------*/
 #define CONFIG_EMAC_NR_START	2	/* start with EMAC 2 (skip 0&1)	*/
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_NET_MULTI	1
 #define CONFIG_PHY_ADDR		0xff	     /* no phy on EMAC0		*/
 #define CONFIG_PHY1_ADDR	0xff	     /* no phy on EMAC1		*/
 #define CONFIG_PHY2_ADDR	0x1
@@ -230,70 +181,12 @@
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
 #define CONFIG_PHY_RESET        1       /* reset phy upon startup         */
 #define CONFIG_PHY_RESET_DELAY	1000
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
 
 /*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*-----------------------------------------------------------------------
- * Miscellaneous configurable options
- *----------------------------------------------------------------------*/
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -312,28 +205,4 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
 #define CFG_PCI_SUBSYS_DEVICEID 0xcafe	/* Whatever */
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/walnut.h b/include/configs/walnut.h
index adc420b..e19c5f3 100644
--- a/include/configs/walnut.h
+++ b/include/configs/walnut.h
@@ -38,122 +38,44 @@
 #define CONFIG_WALNUT		1	/* ...on a WALNUT board		*/
 					/* ...and on a SYCAMORE board	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		walnut
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
 
 #define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll	*/
 
-#define CONFIG_PREBOOT	"echo;" \
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-#define CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=walnut\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
-		"bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=/tftpboot/walnut/uImage\0"				\
+/*
+ * Default environment variables
+ */
+#define	CONFIG_EXTRA_ENV_SETTINGS					\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fff80000\0"					\
 	"ramdisk_addr=fff80000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 /tftpboot/walnut/u-boot.bin\0"		\
-	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
-		"cp.b 100000 fffc0000 40000;"				\
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run net_nfs"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address			*/
-
-#define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 #define CONFIG_HAS_ETH0		1
 
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-#define CONFIG_NET_MULTI		/* needed for NetConsole	*/
-
 #define CONFIG_RTC_DS174x	1	/* use DS1743 RTC in Walnut	*/
 
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
 /*
- * Command line configuration.
+ * Commands additional to the ones defined in amcc-common.h
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 #define CONFIG_CMD_SNTP
 
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
 #define CONFIG_SPD_EEPROM      1       /* use SPD EEPROM for setup    */
 
 /*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-/*
  * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
  * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
  * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
@@ -167,29 +89,11 @@
 #undef	CFG_405_UART_ERRATA_59	       /* 405GP/CR Rev. D silicon */
 #define CFG_BASE_BAUD	    691200
 
-/* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW		1	/* enable loopw command		*/
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
 /*-----------------------------------------------------------------------
  * I2C stuff
  *-----------------------------------------------------------------------
  */
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -224,13 +128,8 @@
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
 #define CFG_FLASH_BASE		0xFFF80000
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
-#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
 
 /*
  * Define here the location of the environment variables (FLASH or NVRAM).
@@ -243,13 +142,6 @@
 #define CFG_ENV_IS_IN_NVRAM	1	/* use NVRAM for environment vars	*/
 #endif
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
@@ -335,21 +227,4 @@
  */
 #define SPD_EEPROM_ADDRESS	0x50
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/yosemite.h b/include/configs/yosemite.h
index f22e798..891b515 100644
--- a/include/configs/yosemite.h
+++ b/include/configs/yosemite.h
@@ -42,6 +42,11 @@
 #define CONFIG_4xx		1	/* ... PPC4xx family		*/
 #define CONFIG_SYS_CLK_FREQ	66666666    /* external freq to pll	*/
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#include "amcc-common.h"
+
 #define CONFIG_BOARD_EARLY_INIT_F 1     /* Call board_early_init_f	*/
 #define CONFIG_MISC_INIT_R	1	/* call misc_init_r()		*/
 #define CONFIG_BOARD_RESET	1	/* call board_reset()		*/
@@ -50,10 +55,6 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_MONITOR_LEN		(512 * 1024)	/* Reserve 512 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(256 * 1024)	/* Reserve 256 kB for malloc()	*/
-#define CFG_MONITOR_BASE	(-CFG_MONITOR_LEN)
-#define CFG_SDRAM_BASE	        0x00000000	    /* _must_ be 0	*/
 #define CFG_FLASH_BASE	        0xfc000000	    /* start of FLASH	*/
 #define CFG_PCI_MEMBASE	        0xa0000000	    /* mapped pci memory*/
 #define CFG_PCI_MEMBASE1        CFG_PCI_MEMBASE  + 0x10000000
@@ -84,14 +85,9 @@
  * Serial Port
  *----------------------------------------------------------------------*/
 #define CFG_EXT_SERIAL_CLOCK	11059200 /* use external 11.059MHz clk	*/
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_SERIAL_MULTI     1
 /*define this if you want console on UART1*/
 #undef CONFIG_UART1_CONSOLE
 
-#define CFG_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * Environment
  *----------------------------------------------------------------------*/
@@ -142,10 +138,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	    /* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			    /* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_MULTI_EEPROMS
 #define CFG_I2C_EEPROM_ADDR	(0xa8>>1)
@@ -167,72 +160,22 @@
 #define CFG_DTT_LOW_TEMP	-30
 #define CFG_DTT_HYSTERESIS	3
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
-/* Setup some board specific values for the default environment variables */
-#ifndef CONFIG_YELLOWSTONE
-#define CONFIG_HOSTNAME		yosemite
-#define CFG_BOOTFILE		"bootfile=/tftpboot/yosemite/uImage\0"
-#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xxFP\0"
-#else
-#define CONFIG_HOSTNAME		yellowstone
-#define CFG_BOOTFILE		"bootfile=/tftpboot/yellowstone/uImage\0"
-#define CFG_ROOTPATH		"rootpath=/opt/eldk/ppc_4xx\0"
-#endif
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	CFG_BOOTFILE							\
-	CFG_ROOTPATH							\
-	"netdev=eth0\0"							\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-	        "bootm\0"						\
-	"bootfile=/tftpboot/${hostname}/uImage\0"			\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_POWERPC					\
+	CONFIG_AMCC_DEF_ENV_PPC_OLD					\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=fc000000\0"					\
 	"ramdisk_addr=fc180000\0"					\
-	"load=tftp 200000 /tftpboot/${hostname}/u-boot.bin\0"		\
-	"update=protect off fff80000 ffffffff;era fff80000 ffffffff;"	\
-		"cp.b 200000 fff80000 80000;"			        \
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#if 0
-#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
-#else
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-#endif
-
-#define CONFIG_BAUDRATE		115200
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_NET_MULTI        1	/* required for netconsole      */
-#define CONFIG_PHY1_ADDR        3
 #define CONFIG_HAS_ETH0		1	/* add support for "ethaddr"	*/
 #define CONFIG_HAS_ETH1		1	/* add support for "eth1addr"	*/
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
-
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
+#define CONFIG_PHY1_ADDR        3
 
 /* Partitions */
 #define CONFIG_MAC_PARTITION
@@ -263,36 +206,11 @@
 #define CONFIG_HW_WATCHDOG			/* watchdog */
 #endif
 
-
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
 #define CONFIG_CMD_DTT
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_SDRAM
 
 #ifdef CONFIG_440EP
     #define CONFIG_CMD_USB
@@ -300,36 +218,6 @@
     #define CONFIG_CMD_EXT2
 #endif
 
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on	        */
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-#define CONFIG_LYNXKDI          1       /* support kdi files            */
-
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
-
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
@@ -347,13 +235,6 @@
 #define CFG_PCI_SUBSYS_VENDORID 0x10e8	/* AMCC */
 #define CFG_PCI_SUBSYS_ID       0xcafe	/* Whatever */
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
@@ -370,21 +251,4 @@
 
 #define CFG_BCSR5_PCI66EN	0x80
 
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
-#define BOOTFLAG_WARM	0x02		/* Software reboot			*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */
diff --git a/include/configs/yucca.h b/include/configs/yucca.h
index 6f9d3e3..026fef6 100644
--- a/include/configs/yucca.h
+++ b/include/configs/yucca.h
@@ -38,13 +38,18 @@
 #define CONFIG_440			1	/* ... PPC440 family	*/
 #define CONFIG_440SPE			1	/* Specifc SPe support	*/
 #define CONFIG_BOARD_EARLY_INIT_F	1	/* Call board_pre_init	*/
-#undef	CFG_DRAM_TEST				/* Disable-takes long time */
 #define CONFIG_SYS_CLK_FREQ	33333333	/* external freq to pll	*/
 #define EXTCLK_33_33		33333333
 #define EXTCLK_66_66		66666666
 #define EXTCLK_50		50000000
 #define EXTCLK_83		83333333
 
+/*
+ * Include common defines/options for all AMCC eval boards
+ */
+#define CONFIG_HOSTNAME		yucca
+#include "amcc-common.h"
+
 #define	CONFIG_MISC_INIT_F	1	/* Use misc_init_f()		*/
 #undef  CONFIG_SHOW_BOOT_PROGRESS
 #undef  CONFIG_STRESS
@@ -53,9 +58,7 @@
  * Base addresses -- Note these are effective addresses where the
  * actual resources get mapped (not physical addresses)
  *----------------------------------------------------------------------*/
-#define CFG_SDRAM_BASE		0x00000000	/* _must_ be 0		*/
 #define CFG_FLASH_BASE		0xfff00000	/* start of FLASH	*/
-#define CFG_MONITOR_BASE	0xfffb0000	/* start of monitor	*/
 #define CFG_PERIPHERAL_BASE	0xa0000000	/* internal peripherals	*/
 #define CFG_ISRAM_BASE		0x90000000	/* internal SRAM	*/
 
@@ -99,24 +102,15 @@
 #define CFG_POST_WORD_ADDR	(CFG_GBL_DATA_OFFSET - 0x4)
 #define CFG_INIT_SP_OFFSET	CFG_POST_WORD_ADDR
 
-#define CFG_MONITOR_LEN		(320 * 1024)	/* Reserve 320 kB for Mon */
-#define CFG_MALLOC_LEN		(512 * 1024)	/* Reserve 512 kB for malloc */
-
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
-#define CONFIG_SERIAL_MULTI	1
 #undef CONFIG_UART1_CONSOLE
 
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
 #undef CFG_EXT_SERIAL_CLOCK
 /* #define CFG_EXT_SERIAL_CLOCK	(1843200 * 6) */ /* Ext clk @ 11.059 MHz */
 
-#define CONFIG_BAUDRATE		115200
-
-#define CFG_BAUDRATE_TABLE  \
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-
 /*-----------------------------------------------------------------------
  * DDR SDRAM
  *----------------------------------------------------------------------*/
@@ -127,10 +121,7 @@
 /*-----------------------------------------------------------------------
  * I2C
  *----------------------------------------------------------------------*/
-#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
-#undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
 #define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
 
 #define IIC0_BOOTPROM_ADDR	0x50
 #define IIC0_ALT_BOOTPROM_ADDR	0x54
@@ -153,123 +144,32 @@
 #undef	CFG_ENV_IS_IN_EEPROM		/* ... not in EEPROM		*/
 #define CONFIG_ENV_OVERWRITE	1
 
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
-	"echo"
-
-#undef	CONFIG_BOOTARGS
-
+/*
+ * Default environment variables
+ */
 #define	CONFIG_EXTRA_ENV_SETTINGS					\
-	"netdev=eth0\0"							\
-	"hostname=yucca\0"						\
-	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
-		"nfsroot=${serverip}:${rootpath}\0"			\
-	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
-	"addip=setenv bootargs ${bootargs} "				\
-		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
-		":${hostname}:${netdev}:off panic=1\0"			\
-	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
-	"flash_nfs=run nfsargs addip addtty;"				\
-		"bootm ${kernel_addr}\0"				\
-	"flash_self=run ramargs addip addtty;"				\
-		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
-	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"     \
-		"bootm\0"						\
-	"rootpath=/opt/eldk/ppc_4xx\0"					\
-	"bootfile=yucca/uImage\0"					\
+	CONFIG_AMCC_DEF_ENV						\
+	CONFIG_AMCC_DEF_ENV_PPC						\
+	CONFIG_AMCC_DEF_ENV_NOR_UPD					\
 	"kernel_addr=E7F10000\0"					\
 	"ramdisk_addr=E7F20000\0"					\
-	"initrd_high=30000000\0"					\
-	"load=tftp 100000 yuca/u-boot.bin\0"				\
-	"update=protect off 2:4-7;era 2:4-7;"				\
-		"cp.b ${fileaddr} FFFB0000 ${filesize};"		\
-		"setenv filesize;saveenv\0"				\
-	"upd=run load update\0"						\
 	"pciconfighost=1\0"						\
 	"pcie_mode=RP:EP:EP\0"						\
 	""
-#define CONFIG_BOOTCOMMAND	"run flash_self"
-
-#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
 
 /*
- * BOOTP options
+ * Commands additional to the ones defined in amcc-common.h
  */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_DIAG
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_NFS
 #define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_REGINFO
 #define CONFIG_CMD_SDRAM
 
-
 #define	CONFIG_IBM_EMAC4_V4	1
-#define CONFIG_MII		1	/* MII PHY management		*/
-#undef CONFIG_NET_MULTI
 #define CONFIG_PHY_ADDR		1	/* PHY address, See schematics	*/
 #define CONFIG_HAS_ETH0
 #define CONFIG_PHY_RESET        1	/* reset phy upon startup	*/
 #define CONFIG_PHY_RESET_DELAY	1000
 #define CONFIG_CIS8201_PHY	1	/* Enable 'special' RGMII mode for Cicada phy */
 #define CONFIG_PHY_GIGE		1	/* Include GbE speed/duplex detection */
-#define CFG_RX_ETH_BUFFER	32	/* Number of ethernet rx buffers & descriptors */
-
-#define CONFIG_NETCONSOLE		/* include NetConsole support	*/
-#define CONFIG_NET_MULTI		/* needed for NetConsole	*/
-
-#undef CONFIG_WATCHDOG			/* watchdog disabled		*/
-
-/*
- * Miscellaneous configurable options
- */
-#define CFG_LONGHELP				/* undef to save memory		*/
-#define CFG_PROMPT		"=> "		/* Monitor Command Prompt	*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
-#else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
-#endif
-#define CFG_PBSIZE		(CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/
-
-#define CFG_LOAD_ADDR		0x100000	/* default load address		*/
-#define CFG_EXTBDINFO		1		/* To use extended board_into (bd_t) */
-
-#define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */
-
-#define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
-#define CONFIG_LOOPW            1       /* enable loopw command         */
-#define CONFIG_MX_CYCLIC        1       /* enable mdc/mwc commands      */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
-#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
 /*-----------------------------------------------------------------------
  * FLASH related
@@ -318,26 +218,6 @@
 /* Support for Intel 82557/82559/82559ER chips. */
 #define CONFIG_EEPRO100
 
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CFG_BOOTMAPSZ		(8 << 20)	/*Initial Memory map for Linux*/
-
-/*
- * Internal Definitions
- *
- * Boot Flags
- */
-#define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH */
-#define BOOTFLAG_WARM	0x02		/* Software reboot */
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
 /* FB Divisor selection */
 #define FPGA_FB_DIV_6		6
 #define FPGA_FB_DIV_10		10
@@ -539,10 +419,4 @@
 #define PERIOD_33_33MHZ		30000	/* 30ns */
 #define PERIOD_25_00MHZ		40000	/* 40ns */
 
-/*---------------------------------------------------------------------------*/
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT	1
-#define CONFIG_OF_BOARD_SETUP	1
-
 #endif	/* __CONFIG_H */