rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

1 files changed, 85 insertions, 85 deletions

diff --git a/include/configs/quad100hd.h b/include/configs/quad100hd.h
index 2e73ff7..1a76301 100644
--- a/include/configs/quad100hd.h
+++ b/include/configs/quad100hd.h
@@ -49,7 +49,7 @@
 #define CONFIG_HAS_ETH1		1
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0x01	/* PHY address			*/
-#define CFG_RX_ETH_BUFFER	16	/* Number of ethernet rx buffers & descriptors */
+#define CONFIG_SYS_RX_ETH_BUFFER	16	/* Number of ethernet rx buffers & descriptors */
 #define CONFIG_PHY_RESET	1
 #define CONFIG_PHY_RESET_DELAY	300	/* PHY RESET recovery delay	*/
 
@@ -84,59 +84,59 @@
 #define CONFIG_SDRAM_BANK0  1
 
 /* FIX! SDRAM timings used in datasheet */
-#define CFG_SDRAM_CL            3       /* CAS latency */
-#define CFG_SDRAM_tRP           20      /* PRECHARGE command period */
-#define CFG_SDRAM_tRC           66      /* ACTIVE-to-ACTIVE command period */
-#define CFG_SDRAM_tRCD          20      /* ACTIVE-to-READ delay */
-#define CFG_SDRAM_tRFC          66      /* Auto refresh period */
+#define CONFIG_SYS_SDRAM_CL            3       /* CAS latency */
+#define CONFIG_SYS_SDRAM_tRP           20      /* PRECHARGE command period */
+#define CONFIG_SYS_SDRAM_tRC           66      /* ACTIVE-to-ACTIVE command period */
+#define CONFIG_SYS_SDRAM_tRCD          20      /* ACTIVE-to-READ delay */
+#define CONFIG_SYS_SDRAM_tRFC          66      /* Auto refresh period */
 
 /*
  * JFFS2
  */
-#define CFG_JFFS2_FIRST_BANK    0
-#ifdef  CFG_KERNEL_IN_JFFS2
-#define CFG_JFFS2_FIRST_SECTOR  0   /* JFFS starts at block 0 */
+#define CONFIG_SYS_JFFS2_FIRST_BANK    0
+#ifdef  CONFIG_SYS_KERNEL_IN_JFFS2
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR  0   /* JFFS starts at block 0 */
 #else /* kernel not in JFFS */
-#define CFG_JFFS2_FIRST_SECTOR  8   /* block 0-7 is kernel (1MB = 8 sectors) */
+#define CONFIG_SYS_JFFS2_FIRST_SECTOR  8   /* block 0-7 is kernel (1MB = 8 sectors) */
 #endif
-#define CFG_JFFS2_NUM_BANKS     1
+#define CONFIG_SYS_JFFS2_NUM_BANKS     1
 
 /*-----------------------------------------------------------------------
  * Serial Port
  *----------------------------------------------------------------------*/
-#undef	CFG_EXT_SERIAL_CLOCK			/* external serial clock */
-#define CFG_BASE_BAUD		691200
+#undef	CONFIG_SYS_EXT_SERIAL_CLOCK			/* external serial clock */
+#define CONFIG_SYS_BASE_BAUD		691200
 #define CONFIG_BAUDRATE		115200
 #define CONFIG_SERIAL_MULTI
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE	\
+#define CONFIG_SYS_BAUDRATE_TABLE	\
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
 
 /*-----------------------------------------------------------------------
  * Miscellaneous configurable options
  *----------------------------------------------------------------------*/
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#define CONFIG_SYS_PROMPT	        "=> "	/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	        1024	/* Console I/O Buffer Size	*/
 #else
-#define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	        256	/* Console I/O Buffer Size	*/
 #endif
-#define CFG_PBSIZE              (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	        16	/* max number of command args	*/
-#define CFG_BARGSIZE	        CFG_CBSIZE /* Boot Argument Buffer Size	*/
+#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	        16	/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	        CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size	*/
 
-#define CFG_MEMTEST_START	0x0400000 /* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
+#define CONFIG_SYS_MEMTEST_START	0x0400000 /* memtest works on		*/
+#define CONFIG_SYS_MEMTEST_END		0x0C00000 /* 4 ... 12 MB in DRAM	*/
 
-#define CFG_LOAD_ADDR		0x100000  /* default load address	*/
-#define CFG_EXTBDINFO		1	/* To use extended board_info (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR		0x100000  /* default load address	*/
+#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_info (bd_t) */
 
-#define CFG_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
+#define CONFIG_SYS_HZ		        1000	/* decrementer freq: 1 ms ticks	*/
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_LOOPW            1       /* enable loopw command         */
@@ -149,53 +149,53 @@
  *----------------------------------------------------------------------*/
 #define CONFIG_HARD_I2C		1		/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_SLAVE		0x7F
 
-#define CFG_I2C_EEPROM_ADDR	0x50		/* base address */
-#define CFG_I2C_EEPROM_ADDR_LEN	2		/* bytes of address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* base address */
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2		/* bytes of address */
 
-#define CFG_EEPROM_PAGE_WRITE_BITS	5	/* 8 byte write page size */
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
-#define CFG_EEPROM_SIZE			0x2000
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* 8 byte write page size */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
+#define CONFIG_SYS_EEPROM_SIZE			0x2000
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_FLASH_BASE		0xFFC00000
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
-#define CFG_MONITOR_BASE	(TEXT_BASE)
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		0xFFC00000
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+#define CONFIG_SYS_MONITOR_BASE	(TEXT_BASE)
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_FLASH_CFI			/* The flash is CFI compatible	*/
+#define CONFIG_SYS_FLASH_CFI			/* The flash is CFI compatible	*/
 #define	CONFIG_FLASH_CFI_DRIVER
 
-#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
 
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks	*/
-#define CFG_MAX_FLASH_SECT	128	/* max number of sectors on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks	*/
+#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max number of sectors on one chip */
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms) */
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms) */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms) */
 
-#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster) */
-#define CFG_FLASH_INCREMENT      0       /* there is only one bank         */
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster) */
+#define CONFIG_SYS_FLASH_INCREMENT      0       /* there is only one bank         */
 
-#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash */
+#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash */
 
 #ifdef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SECT_SIZE	0x10000	/* size of one complete sector	*/
@@ -210,21 +210,21 @@
 #ifdef CONFIG_ENV_IS_IN_EEPROM
 #define CONFIG_ENV_SIZE		0x400		/* Size of Environment vars */
 #define CONFIG_ENV_OFFSET		0x00000000
-#define CFG_ENABLE_CRC_16	1       /* Intrinsyc formatting used crc16 */
+#define CONFIG_SYS_ENABLE_CRC_16	1       /* Intrinsyc formatting used crc16 */
 #endif
 
 /* partly from PPCBoot */
 /* NAND */
 #define CONFIG_NAND
 #ifdef CONFIG_NAND
-#define CFG_NAND_BASE   0x60000000
-#define CFG_NAND_CS	10   /* our CS is GPIO10 */
-#define CFG_NAND_RDY	23   /* our RDY is GPIO23 */
-#define CFG_NAND_CE	24   /* our CE is GPIO24  */
-#define CFG_NAND_CLE	31   /* our CLE is GPIO31 */
-#define CFG_NAND_ALE	30   /* our ALE is GPIO30 */
+#define CONFIG_SYS_NAND_BASE   0x60000000
+#define CONFIG_SYS_NAND_CS	10   /* our CS is GPIO10 */
+#define CONFIG_SYS_NAND_RDY	23   /* our RDY is GPIO23 */
+#define CONFIG_SYS_NAND_CE	24   /* our CE is GPIO24  */
+#define CONFIG_SYS_NAND_CLE	31   /* our CLE is GPIO31 */
+#define CONFIG_SYS_NAND_ALE	30   /* our ALE is GPIO30 */
 #define NAND_MAX_CHIPS	1
-#define CFG_MAX_NAND_DEVICE	1
+#define CONFIG_SYS_MAX_NAND_DEVICE	1
 #endif
 
 /*-----------------------------------------------------------------------
@@ -232,17 +232,17 @@
  */
 /* use on chip memory (OCM) for temperary stack until sdram is tested */
 /* see ./cpu/ppc4xx/start.S */
-#define CFG_TEMP_STACK_OCM	1
+#define CONFIG_SYS_TEMP_STACK_OCM	1
 
 /* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR	0xF8000000
-#define CFG_OCM_DATA_SIZE	0x1000
-#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of OCM		*/
-#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of OCM		*/
+#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM	*/
 
-#define CFG_GBL_DATA_SIZE	128  /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE	128  /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
@@ -250,17 +250,17 @@
  */
 
 /* see ./cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/ndfc.c */
-#define CFG_EBC_PB0AP		0x04002480
+#define CONFIG_SYS_EBC_PB0AP		0x04002480
 /* AMD NOR flash - this corresponds to FLASH_BASE so may be correct */
-#define CFG_EBC_PB0CR		0xFFC5A000
-#define CFG_EBC_PB1AP           0x04005480
-#define CFG_EBC_PB1CR           0x60018000
-#define CFG_EBC_PB2AP           0x00000000
-#define CFG_EBC_PB2CR           0x00000000
-#define CFG_EBC_PB3AP           0x00000000
-#define CFG_EBC_PB3CR           0x00000000
-#define CFG_EBC_PB4AP           0x00000000
-#define CFG_EBC_PB4CR           0x00000000
+#define CONFIG_SYS_EBC_PB0CR		0xFFC5A000
+#define CONFIG_SYS_EBC_PB1AP           0x04005480
+#define CONFIG_SYS_EBC_PB1CR           0x60018000
+#define CONFIG_SYS_EBC_PB2AP           0x00000000
+#define CONFIG_SYS_EBC_PB2CR           0x00000000
+#define CONFIG_SYS_EBC_PB3AP           0x00000000
+#define CONFIG_SYS_EBC_PB3CR           0x00000000
+#define CONFIG_SYS_EBC_PB4AP           0x00000000
+#define CONFIG_SYS_EBC_PB4CR           0x00000000
 
 /*-----------------------------------------------------------------------
  * Definitions for GPIO setup (PPC405EP specific)
@@ -268,14 +268,14 @@
  * Taken in part from PPCBoot board/icecube/icecube.h
  */
 /* see ./cpu/ppc4xx/cpu_init.c ./cpu/ppc4xx/start.S */
-#define CFG_GPIO0_OSRH		0x55555550
-#define CFG_GPIO0_OSRL		0x00000110
-#define CFG_GPIO0_ISR1H		0x00000000
-#define CFG_GPIO0_ISR1L		0x15555445
-#define CFG_GPIO0_TSRH		0x00000000
-#define CFG_GPIO0_TSRL		0x00000000
-#define CFG_GPIO0_TCR		0xFFFF8097
-#define CFG_GPIO0_ODR		0x00000000
+#define CONFIG_SYS_GPIO0_OSRH		0x55555550
+#define CONFIG_SYS_GPIO0_OSRL		0x00000110
+#define CONFIG_SYS_GPIO0_ISR1H		0x00000000
+#define CONFIG_SYS_GPIO0_ISR1L		0x15555445
+#define CONFIG_SYS_GPIO0_TSRH		0x00000000
+#define CONFIG_SYS_GPIO0_TSRL		0x00000000
+#define CONFIG_SYS_GPIO0_TCR		0xFFFF8097
+#define CONFIG_SYS_GPIO0_ODR		0x00000000
 
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */