Merge branch 'master' of git://git.denx.de/u-boot-arm

1 files changed, 0 insertions, 359 deletions

diff --git a/include/configs/mpq101.h b/include/configs/mpq101.h
deleted file mode 100644
index 4cac8ee..0000000
--- a/include/configs/mpq101.h
+++ /dev/null
@@ -1,359 +0,0 @@
-/*
- * Copyright 2011 Alex Dubov <oakad@yahoo.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Merury Computers MPQ101 board configuration file
- *
- */
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#ifdef CONFIG_36BIT
-# define CONFIG_PHYS_64BIT
-#endif
-
-/* High Level Configuration Options */
-#define CONFIG_BOOKE      /* BOOKE */
-#define CONFIG_E500       /* BOOKE e500 family */
-#define CONFIG_MPC85xx    /* MPC8540/60/55/41/48 */
-#define CONFIG_MPC8548    /* MPC8548 specific */
-#define CONFIG_MPQ101     /* MPQ101 board specific */
-
-#define CONFIG_SYS_SRIO   /* enable serial RapidIO */
-#define CONFIG_TSEC_ENET  /* tsec ethernet support */
-#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
-#define CONFIG_FSL_LAW    /* Use common FSL init code */
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_L2_CACHE   /* toggle L2 cache */
-#define CONFIG_BTB        /* toggle branch predition */
-
-#define CONFIG_PANIC_HANG
-
-/*
- * Only possible on E500 Version 2 or newer cores.
- */
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#ifdef CONFIG_PHYS_64BIT
-# define CONFIG_ADDR_MAP
-# define CONFIG_SYS_NUM_ADDR_MAP 16 /* number of TLB1 entries */
-#endif
-
-
-#define CONFIG_SYS_CLK_FREQ      33000000 /* sysclk for MPC85xx */
-
-#define CONFIG_SYS_CCSRBAR		0xe0000000
-#define CONFIG_SYS_CCSRBAR_PHYS_LOW	CONFIG_SYS_CCSRBAR
-
-/* DDR Setup */
-#define CONFIG_SYS_FSL_DDR2
-
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
-
-#define CONFIG_MEM_INIT_VALUE        0xDeadBeef
-#define CONFIG_SYS_DDR_SDRAM_BASE    0x00000000 /* DDR is system memory*/
-#define CONFIG_SYS_SDRAM_BASE        CONFIG_SYS_DDR_SDRAM_BASE
-
-#define CONFIG_NUM_DDR_CONTROLLERS   1
-#define CONFIG_DIMM_SLOTS_PER_CTLR   1
-#define CONFIG_CHIP_SELECTS_PER_CTRL (2 * CONFIG_DIMM_SLOTS_PER_CTLR)
-
-/* Fixed 512MB DDR2 parameters */
-#define CONFIG_SYS_SDRAM_SIZE_LOG    29 /* DDR is 512MB */
-#define CONFIG_SYS_DDR_CS0_BNDS      0x0000001f
-#define CONFIG_SYS_DDR_CS0_CONFIG    0x80014102
-#define CONFIG_SYS_DDR_TIMING_3      0x00010000
-#define CONFIG_SYS_DDR_TIMING_0      0x00260802
-#define CONFIG_SYS_DDR_TIMING_1      0x5c47a432
-#define CONFIG_SYS_DDR_TIMING_1_PERF 0x49352322
-#define CONFIG_SYS_DDR_TIMING_2      0x03984cce
-#define CONFIG_SYS_DDR_TIMING_2_PERF 0x14904cca
-#define CONFIG_SYS_DDR_MODE_1        0x00400442
-#define CONFIG_SYS_DDR_MODE_1_PERF   0x00480432
-#define CONFIG_SYS_DDR_MODE_2        0x00000000
-#define CONFIG_SYS_DDR_MODE_2_PERF   0x00000000
-#define CONFIG_SYS_DDR_INTERVAL      0x08200100
-#define CONFIG_SYS_DDR_INTERVAL_PERF 0x06180100
-#define CONFIG_SYS_DDR_CLK_CTRL      0x03800000
-#define CONFIG_SYS_DDR_CONTROL       0xc3008000 /* Type = DDR2 */
-#define CONFIG_SYS_DDR_CONTROL2      0x04400000
-
-#define CONFIG_SYS_ALT_MEMTEST
-#define CONFIG_SYS_MEMTEST_START     0x0ff00000 /* memtest works on */
-#define CONFIG_SYS_MEMTEST_END       0x0ffffffc
-
-/*
- * RAM definitions
- */
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR   0xe4010000 /* Initial RAM address */
-#define CONFIG_SYS_INIT_RAM_SIZE   0x4000     /* Size of used area in RAM */
-
-#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE \
-				    - GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET  CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_LEN     (256 * 1024)  /* Reserve 256 kB for Mon */
-#define CONFIG_SYS_MALLOC_LEN      (1024 * 1024) /* Reserved for malloc */
-
-/*
- * Local Bus Definitions
- */
-#define CONFIG_SYS_LBC_LCRR 0x00000004 /* LB clock ratio reg */
-#define CONFIG_SYS_LBC_LBCR 0x00000000 /* LB config reg */
-
-
-/*
- * FLASH on the Local Bus
- * One bank, 128M, using the CFI driver.
- */
-#define CONFIG_SYS_BOOT_BLOCK 0xf8000000            /* boot TLB block */
-#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_BOOT_BLOCK /* start of FLASH 128M */
-
-#ifdef CONFIG_PHYS_64BIT
-# define CONFIG_SYS_FLASH_BASE_PHYS 0xff8000000ull
-#else
-# define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
-#endif
-
-/* 0xf8001801 */
-#define CONFIG_SYS_BR0_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \
-			       | BR_PS_32 | BR_V)
-
-/* 0xf8006ff7 */
-#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(128) | OR_GPCM_XAM | OR_GPCM_CSNT \
-			       | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS \
-			       | OR_GPCM_SCY_15 | OR_GPCM_TRLX \
-			       | OR_GPCM_EHTR | OR_GPCM_EAD)
-
-#define CONFIG_SYS_FLASH_BANKS_LIST    {CONFIG_SYS_FLASH_BASE_PHYS}
-#define CONFIG_FLASH_SHOW_PROGRESS     45   /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS     1    /* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT      512  /* sectors per device */
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT    60000 /* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT    500   /* Flash Write Timeout (ms) */
-
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
-/*
- * When initializing flash, if we cannot find the manufacturer ID,
- * assume this is the AMD flash.
- */
-#define CONFIG_ASSUME_AMD_FLASH
-
-/*
- * Environment parameters
- */
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_OVERWRITE
-#define CONFIG_SYS_USE_PPCENV
-#define ENV_IS_EMBEDDED
-#define CONFIG_ENV_SECT_SIZE 0x40000   /* 256K */
-#define CONFIG_ENV_SIZE      0x800
-
-/* Environment at the start of flash sector, before text. */
-#define CONFIG_ENV_ADDR         (CONFIG_SYS_TEXT_BASE - CONFIG_ENV_SIZE)
-#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
-#define CONFIG_SYS_TEXT_BASE    0xfffc0800
-#define CONFIG_SYS_LDSCRIPT     "board/mercury/mpq101/u-boot.lds"
-
-/*
- * Cypress CY7C67200 USB controller on the Local Bus.
- * Not supported by u-boot at present.
- */
-#define CONFIG_SYS_LBC_OPTION_BASE 0xf0000000
-
-#ifdef CONFIG_PHYS_64BIT
-# define CONFIG_SYS_LBC_OPTION_BASE_PHYS 0xff0000000ull
-#else
-# define CONFIG_SYS_LBC_OPTION_BASE_PHYS CONFIG_SYS_LBC_OPTION_BASE
-#endif
-
-/* 0xf0001001 */
-#define CONFIG_SYS_BR1_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_LBC_OPTION_BASE_PHYS) \
-			       | BR_PS_16 | BR_V)
-
-/* fffff002 */
-#define CONFIG_SYS_OR1_PRELIM (P2SZ_TO_AM(0x8000) | OR_GPCM_XAM \
-			       | OR_GPCM_BCTLD | OR_GPCM_EHTR)
-
-/*
- * Serial Ports
- */
-#define CONFIG_CONS_INDEX           2
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE 1
-#define CONFIG_SYS_NS16550_CLK      get_bus_freq(0)
-
-#define CONFIG_SYS_BAUDRATE_TABLE   {300, 600, 1200, 2400, 4800, 9600, \
-				     19200, 38400, 115200}
-
-#define CONFIG_SYS_NS16550_COM1     (CONFIG_SYS_CCSRBAR+0x4500)
-#define CONFIG_SYS_NS16550_COM2     (CONFIG_SYS_CCSRBAR+0x4600)
-
-/*
- * I2C buses and peripherals
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SPEED	400000
-#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
-#define CONFIG_SYS_FSL_I2C2_SPEED	400000
-#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
-#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
-#define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69} }
-
-/* I2C RTC - M41T81 */
-#define CONFIG_RTC_M41T62
-#define CONFIG_SYS_I2C_RTC_ADDR     0x68
-#define CONFIG_SYS_M41T11_BASE_YEAR 2000
-
-/* I2C EEPROM - 24C256 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR            0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS     6
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 12
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN        2
-#define CONFIG_SYS_EEPROM_BUS_NUM             1
-
-/*
- * RapidIO MMU
- */
-#ifdef CONFIG_SYS_SRIO
-# define CONFIG_SRIO1
-# define CONFIG_SYS_SRIO1_MEM_VIRT  0xc0000000
-# define CONFIG_SYS_SRIO1_MEM_SIZE  0x20000000 /* 512M */
-
-# ifdef CONFIG_PHYS_64BIT
-#  define CONFIG_SYS_SRIO1_MEM_PHYS 0xfc0000000ull
-# else
-#  define CONFIG_SYS_SRIO1_MEM_PHYS CONFIG_SYS_SRIO1_MEM_VIRT
-# endif
-#endif
-
-/*
- * Ethernet
- */
-#ifdef CONFIG_TSEC_ENET
-
-# define CONFIG_MII                /* MII PHY management */
-# define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
-
-# define CONFIG_TSEC1
-# define CONFIG_TSEC1_NAME       "eTSEC0"
-# define TSEC1_PHY_ADDR          0x10
-# define TSEC1_PHYIDX            0
-# define TSEC1_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
-
-# define CONFIG_TSEC2
-# define CONFIG_TSEC2_NAME       "eTSEC1"
-# define TSEC2_PHY_ADDR          0x11
-# define TSEC2_PHYIDX            0
-# define TSEC2_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
-
-# define CONFIG_TSEC3
-# define CONFIG_TSEC3_NAME       "eTSEC2"
-# define TSEC3_PHY_ADDR          0x12
-# define TSEC3_PHYIDX            0
-# define TSEC3_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
-
-# define CONFIG_TSEC4
-# define CONFIG_TSEC4_NAME       "eTSEC3"
-# define TSEC4_PHY_ADDR          0x13
-# define TSEC4_PHYIDX            0
-# define TSEC4_FLAGS             (TSEC_GIGABIT | TSEC_REDUCED)
-
-/* Options are: eTSEC[0-3] */
-# define CONFIG_ETHPRIME         "eTSEC0"
-# define CONFIG_PHY_GIGE         /* Include GbE speed/duplex detection */
-#endif
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_SETEXPR
-#define CONFIG_CMD_JFFS2
-
-/*
- * Miscellaneous configurable options
- */
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-#define CONFIG_FIT         /* new uImage format support */
-#define CONFIG_FIT_VERBOSE /* enable fit_format_{error,warning}() */
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-
-
-#define CONFIG_LOADS_ECHO            /* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */
-
-#define CONFIG_SYS_LONGHELP          /* undef to save memory */
-#define CONFIG_CMDLINE_EDITING       /* Command-line editing */
-#define CONFIG_AUTO_COMPLETE         /* add autocompletion support */
-
-#define CONFIG_SYS_LOAD_ADDR         0x2000000    /* default load address */
-#define CONFIG_SYS_PROMPT            "MPQ-101=> " /* Monitor Command Prompt */
-
-/* Console I/O Buffer Size */
-#ifdef CONFIG_CMD_KGDB
-# define CONFIG_SYS_CBSIZE 1024
-#else
-# define CONFIG_SYS_CBSIZE 256
-#endif
-
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
-
-#define CONFIG_SYS_MAXARGS  16                /* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 16 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN (16 << 20) /* Increase max gunzip size */
-
-#ifdef CONFIG_CMD_KGDB
-# define CONFIG_KGDB_BAUDRATE  230400 /* speed to run kgdb serial port */
-#endif
-
-/*
- * Basic Environment Configuration
- */
-#define CONFIG_BAUDRATE  115200
-#define CONFIG_BOOTDELAY 5            /* -1 disables auto-boot */
-
-/*default location for tftp and bootm*/
-#define CONFIG_LOADADDR  CONFIG_SYS_LOAD_ADDR
-
-#endif /* __CONFIG_H */