Merge branch 'master' of git://git.denx.de/u-boot-i2c

The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
	board/sandburst/common/ppc440gx_i2c.c
	board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>

3 files changed, 39 insertions, 15 deletions

diff --git a/include/configs/km/keymile-common.h b/include/configs/km/keymile-common.h
index d0e4b3f..a82987d 100644
--- a/include/configs/km/keymile-common.h
+++ b/include/configs/km/keymile-common.h
@@ -62,10 +62,7 @@
 #define CONFIG_LOADS_ECHO
 #define CONFIG_SYS_LOADS_BAUD_CHANGE
 
-#define CONFIG_I2C_MULTI_BUS
-#define CONFIG_SYS_MAX_I2C_BUS		1
 #define CONFIG_SYS_I2C_INIT_BOARD
-#define CONFIG_I2C_MUX
 
 /* Support the IVM EEprom */
 #define	CONFIG_SYS_IVM_EEPROM_ADR	0x50
diff --git a/include/configs/km/km83xx-common.h b/include/configs/km/km83xx-common.h
index 6b3a4cc..0ff866a 100644
--- a/include/configs/km/km83xx-common.h
+++ b/include/configs/km/km83xx-common.h
@@ -201,11 +201,23 @@
 #endif /* CFG_SYS_RAMBOOT */
 
 /* I2C */
-#define CONFIG_HARD_I2C		/* I2C with hardware support */
-#define CONFIG_FSL_I2C
-#define CONFIG_SYS_I2C_SPEED	200000	/* I2C speed and slave address */
-#define CONFIG_SYS_I2C_SLAVE	0x7F
-#define CONFIG_SYS_I2C_OFFSET	0x3000
+#define CONFIG_SYS_I2C
+#define CONFIG_SYS_NUM_I2C_BUSES	4
+#define CONFIG_SYS_I2C_MAX_HOPS		1
+#define CONFIG_SYS_I2C_FSL
+#define CONFIG_SYS_FSL_I2C_SPEED	200000
+#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_FSL_I2C2_SPEED	200000
+#define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
+#define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
+#define CONFIG_SYS_I2C_BUSES	{{0, {I2C_NULL_HOP} }, \
+		{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+		{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+		{1, {I2C_NULL_HOP} } }
+
+#define CONFIG_KM_IVM_BUS		2	/* I2C2 (Mux-Port 1)*/
 
 /* I2C SYSMON (LM75, AD7414 is almost compatible) */
 #define CONFIG_DTT_LM75		/* ON Semi's LM75 */
@@ -213,7 +225,7 @@
 #define CONFIG_SYS_DTT_MAX_TEMP	70
 #define CONFIG_SYS_DTT_LOW_TEMP	-30
 #define CONFIG_SYS_DTT_HYSTERESIS	3
-#define CONFIG_SYS_DTT_BUS_NUM		(CONFIG_SYS_MAX_I2C_BUS)
+#define CONFIG_SYS_DTT_BUS_NUM		1
 
 #if defined(CONFIG_CMD_NAND)
 #define CONFIG_NAND_KMETER1
@@ -309,7 +321,6 @@
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	CONFIG_KM_DEF_ENV						\
 	CONFIG_KM_DEF_ARCH						\
-	"EEprom_ivm=pca9547:70:9\0"					\
 	"newenv="							\
 		"prot off 0xF00C0000 +0x40000 && "			\
 		"era 0xF00C0000 +0x40000\0"				\
diff --git a/include/configs/km/km_arm.h b/include/configs/km/km_arm.h
index 97bdeba..e0368cb 100644
--- a/include/configs/km/km_arm.h
+++ b/include/configs/km/km_arm.h
@@ -42,7 +42,6 @@
 
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_SF
-#define CONFIG_SOFT_I2C		/* I2C bit-banged	*/
 
 /* SPI NOR Flash default params, used by sf commands */
 #define CONFIG_SF_DEFAULT_SPEED		8100000
@@ -171,8 +170,23 @@
 /*
  * I2C related stuff
  */
+#undef CONFIG_I2C_MVTWSI
+#define CONFIG_SYS_I2C
+#define	CONFIG_SYS_I2C_SOFT	/* I2C bit-banged	*/
+
 #define	CONFIG_KIRKWOOD_GPIO		/* Enable GPIO Support */
-#if defined(CONFIG_SOFT_I2C)
+#if defined(CONFIG_SYS_I2C_SOFT)
+
+#define CONFIG_SYS_NUM_I2C_BUSES	6
+#define CONFIG_SYS_I2C_MAX_HOPS		1
+#define CONFIG_SYS_I2C_BUSES	{	{0, {I2C_NULL_HOP} }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
+					{0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
+				}
+
 #ifndef __ASSEMBLY__
 #include <asm/arch-kirkwood/gpio.h>
 extern void __set_direction(unsigned pin, int high);
@@ -195,6 +209,8 @@ int get_scl(void);
 #define I2C_DELAY	udelay(1)
 #define I2C_SOFT_DECLARATIONS
 
+#define	CONFIG_SYS_I2C_SOFT_SLAVE	0x0
+#define	CONFIG_SYS_I2C_SOFT_SPEED	100000
 #endif
 
 /* EEprom support 24C128, 24C256 valid for environment eeprom */
@@ -224,7 +240,7 @@ int get_scl(void);
 #define CONFIG_SYS_EEPROM_WREN
 #define CONFIG_ENV_OFFSET		0x0 /* no bracets! */
 #define CONFIG_ENV_SIZE			(0x2000 - CONFIG_ENV_OFFSET)
-#define CONFIG_I2C_ENV_EEPROM_BUS	KM_ENV_BUS "\0"
+#define CONFIG_I2C_ENV_EEPROM_BUS	KM_ENV_BUS
 #define CONFIG_ENV_OFFSET_REDUND	0x2000 /* no bracets! */
 #define CONFIG_ENV_SIZE_REDUND		(CONFIG_ENV_SIZE)
 #endif
@@ -263,7 +279,8 @@ int get_scl(void);
 #else
 #define CONFIG_KM_NEW_ENV						\
 	"newenv=setenv addr 0x100000 && "				\
-		"i2c dev 1; mw.b ${addr} 0 4 && "			\
+		"i2c dev " __stringify(CONFIG_I2C_ENV_EEPROM_BUS) "; "  \
+		"mw.b ${addr} 0 4 && "					\
 		"eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR)	\
 		" ${addr} " __stringify(CONFIG_ENV_OFFSET) " 4 && "	\
 		"eeprom write " __stringify(CONFIG_SYS_DEF_EEPROM_ADDR)	\
@@ -277,7 +294,6 @@ int get_scl(void);
 	CONFIG_KM_DEF_ENV						\
 	CONFIG_KM_NEW_ENV						\
 	"arch=arm\0"							\
-	"EEprom_ivm=" KM_IVM_BUS "\0"					\
 	""
 
 #if defined(CONFIG_SYS_NO_FLASH)