powerpc: mpc5xxx: remove galaxy5200 board support

This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Eric Millbrandt <emillbrandt@dekaresearch.com>

1 files changed, 0 insertions, 431 deletions

diff --git a/include/configs/galaxy5200.h b/include/configs/galaxy5200.h
deleted file mode 100644
index b555d82..0000000
--- a/include/configs/galaxy5200.h
+++ /dev/null
@@ -1,431 +0,0 @@
-/*
- * (C) Copyright 2003-2005
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * (C) Copyright 2006
- * Eric Schumann, Phytec Messatechnik GmbH
- *
- * (C) Copyright 2009
- * Jon Smirl <jonsmirl@gmail.com>
- *
- * (C) Copyright 2009
- * Eric Millbrandt, DEKA Research and Development Corporation
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#define CONFIG_BOARDINFO	 "galaxy5200"
-
-/*
- * High Level Configuration Options
- * (easy to change)
- */
-#define CONFIG_MPC5200		1	/* This is an MPC5200 CPU */
-#define CONFIG_SYS_MPC5XXX_CLKIN 33333333	/* ... running at 33.333333MHz */
-
-/*
- * Valid values for CONFIG_SYS_TEXT_BASE are:
- * 0xFFF00000	boot high (standard configuration)
- * 0xFE000000	boot low
- * 0x00100000	boot from RAM (for testing only) does not work
- */
-#ifdef CONFIG_galaxy5200_LOWBOOT
-#define	CONFIG_SYS_TEXT_BASE	0xFE000000
-#endif
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xFFF00000	/* Standard: boot high */
-#endif
-
-/*
- * Serial console configuration
- */
-#define CONFIG_PSC_CONSOLE	4	/* console is on PSC4 -> */
-					/* define gps port conf. */
-					/* register later on to  */
-					/* enable UART function! */
-#define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
-#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DATE
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_JFFS2
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NFS
-#define CONFIG_CMD_SNTP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_ASKENV
-#define CONFIG_CMD_USB
-#define CONFIG_CMD_CACHE
-#define CONFIG_CMD_FAT
-
-#define	CONFIG_TIMESTAMP	1	/* Print image info with timestamp */
-
-#if (CONFIG_SYS_TEXT_BASE == 0xFE000000)		/* Boot low */
-#define CONFIG_SYS_LOWBOOT 1
-#endif
-/* RAMBOOT will be defined automatically in memory section */
-
-#define MTDIDS_DEFAULT		"nor0=physmap-flash.0"
-#define MTDPARTS_DEFAULT	"mtdparts=physmap-flash.0:256k(ubootl)," \
-	"1792k(kernel),13312k(jffs2),256k(uboot)ro,256k(oftree),-(space)"
-
-/*
- * Autobooting
- */
-#define CONFIG_BOOTDELAY	10	/* autoboot after 10 seconds */
-#define CONFIG_ZERO_BOOTDELAY_CHECK	/* allow stopping of boot process */
-					/* even with bootdelay=0 */
-#define CONFIG_BOOT_RETRY_TIME 120	/* Reset if no command is entered  */
-#define CONFIG_RESET_TO_RETRY
-
-#define CONFIG_PREBOOT	"echo;"	\
-	"echo Welcome to U-Boot;"\
-	"echo"
-
-#define CONFIG_BOOTCOMMAND     "go ff300004 0; go ff300004 2 2;" \
-	"bootm ff040000 ff900000 fffc0000"
-#define CONFIG_BOOTARGS        "console=ttyPSC0,115200"
-#define CONFIG_EXTRA_ENV_SETTINGS "epson=yes\0"
-
-/*
- * IPB Bus clocking configuration.
- */
-#define CONFIG_SYS_IPBCLK_EQUALS_XLBCLK	/* define for 133MHz speed */
-#define CONFIG_SYS_XLB_PIPELINING	1
-
-/*
- * I2C configuration
- */
-#define CONFIG_HARD_I2C 1		/* I2C with hardware support */
-#define CONFIG_SYS_I2C_MODULE 2		/* Select I2C module #1 or #2 */
-#define CONFIG_SYS_I2C_SPEED 100000	/* 100 kHz */
-#define CONFIG_SYS_I2C_SLAVE 0x7F
-#define CONFIG_SYS_I2C_INIT_MPC5XXX	/* Reset devices on i2c bus */
-
-/*
- * EEPROM CAT24WC32 configuration
- */
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x52	/* 1010100x */
-#define CONFIG_SYS_I2C_FACT_ADDR	0x52	/* EEPROM CAT24WC32 */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address */
-#define CONFIG_SYS_EEPROM_SIZE		4096
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 15
-
-/*
- * RTC configuration
- */
-#define RTC
-#define CONFIG_RTC_DS3231		1
-#define CONFIG_SYS_I2C_RTC_ADDR		0x68
-
-/*
- * Flash configuration
- */
-
-#define CONFIG_SYS_FLASH_BASE		0xfe000000
-/*
- * The flash size is autoconfigured, but arch/powerpc/cpu/mpc5xxx/cpu_init.c needs this
- * variable defined
- */
-#define CONFIG_SYS_FLASH_SIZE		0x02000000
-#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
-
-#define CONFIG_SYS_FLASH_CFI 1		/* Flash is CFI conformant */
-#define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_MAX_FLASH_SECT 259	/* max num of sects on one chip */
-#define CONFIG_SYS_MAX_FLASH_BANKS 1	/* max num of flash banks */
-					/* (= chip selects) */
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-
-/*
- * Use hardware protection. This seems required, as the BDI uses hardware
- * protection. Without this, U-Boot can't work with this sectors as its
- * protection is software only by default.
- */
-#define CONFIG_SYS_FLASH_PROTECTION	1
-
-/*
- * Environment settings
- */
-
-#define CONFIG_ENV_IS_IN_EEPROM	1
-#define CONFIG_ENV_OFFSET	0x00	/* environment starts at the */
-					/* beginning of the EEPROM */
-#define CONFIG_ENV_SIZE		CONFIG_SYS_EEPROM_SIZE
-
-#define CONFIG_ENV_OVERWRITE	1
-
-/*
- * SDRAM configuration
- */
-#define SDRAM_DDR	1
-#define SDRAM_MODE	0x018D0000
-#define SDRAM_EMODE	0x40090000
-#define SDRAM_CONTROL	0x71500F00
-#define SDRAM_CONFIG1	0x73711930
-#define SDRAM_CONFIG2	0x47770000
-
-/*
- * Memory map
- */
-#define CONFIG_SYS_MBAR	0xF0000000	/* MBAR has to be switched by other */
-					/* bootloader or debugger config */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_DEFAULT_MBAR		0x80000000
-
-/* Use SRAM until RAM will be available */
-#define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
-
-/* End of used area in SPRAM */
-#define CONFIG_SYS_INIT_RAM_SIZE		MPC5XXX_SRAM_SIZE
-
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE
-#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
-#	define CONFIG_SYS_RAMBOOT		1
-#endif
-
-#define CONFIG_SYS_MONITOR_LEN (192 << 10)	/* Reserve 192 kB for Monitor */
-#define CONFIG_SYS_MALLOC_LEN (128 << 10)	/* Reserve 128 kB for malloc() */
-#define CONFIG_SYS_BOOTMAPSZ (8 << 20)	/* Initial Memory map for Linux */
-
-/* Chip Select configuration for NAND flash */
-#define CONFIG_SYS_CS1_START		0x20000000
-#define CONFIG_SYS_CS1_SIZE		0x90000
-#define CONFIG_SYS_CS1_CFG		0x00025b00
-
-/* Chip Select configuration for Epson S1D13513 */
-#define CONFIG_SYS_CS3_START		0x10000000
-#define CONFIG_SYS_CS3_SIZE		0x400000
-#define CONFIG_SYS_CS3_CFG		0xffff3d10
-
-/*
- * Ethernet configuration
- */
-#define CONFIG_MPC5xxx_FEC		1
-#define CONFIG_MPC5xxx_FEC_MII100
-#define CONFIG_PHY_ADDR			0x01
-#define CONFIG_NO_AUTOLOAD		1
-
-/*
- * GPIO configuration
- *
- * GPS port configuration
- *
- * [29:31] = 01x
- * AC97 on PSC1
- * PSC1_0 -> AC97 SDATA out
- * PSC1_1 -> AC97 SDTA in
- * PSC1_2 -> AC97 SYNC out
- * PSC1_3 -> AC97 bitclock out
- * PSC1_4 -> AC97 reset out
- *
- * [28] = Reserved
- *
- * [25:27] = 110
- * SPI on PSC2
- * PSC2_0 -> MOSI
- * PSC2_1 -> MISO
- * PSC2_2 -> n/a
- * PSC2_3 -> CLK
- * PSC2_4 -> SS
- *
- * [24] = Reserved
- *
- * [20:23] = 0001
- * USB on PSC3
- * PSC3_0 -> USB_OE OE out
- * PSC3_1 -> USB_TXN Tx- out
- * PSC3_2 -> USB_TXP Tx+ out
- * PSC3_3 -> USB_TXD
- * PSC3_4 -> USB_RXP Rx+ in
- * PSC3_5 -> USB_RXN Rx- in
- * PSC3_6 -> USB_PWR PortPower out
- * PSC3_7 -> USB_SPEED speed out
- * PSC3_8 -> USB_SUSPEND suspend
- * PSC3_9 -> USB_OVRCURNT overcurrent in
- *
- * [18:19] = 10
- * Two UARTs
- *
- * [17] = 0
- * USB differential mode
- *
- * [16] = 1
- * PCI disabled
- *
- * [12:15] = 0101
- * Ethernet 100Mbit with MD
- * ETH_0 -> ETH Txen
- * ETH_1 -> ETH TxD0
- * ETH_2 -> ETH TxD1
- * ETH_3 -> ETH TxD2
- * ETH_4 -> ETH TxD3
- * ETH_5 -> ETH Txerr
- * ETH_6 -> ETH MDC
- * ETH_7 -> ETH MDIO
- * ETH_8 -> ETH RxDv
- * ETH_9 -> ETH RxCLK
- * ETH_10 -> ETH Collision
- * ETH_11 -> ETH TxD
- * ETH_12 -> ETH RxD0
- * ETH_13 -> ETH RxD1
- * ETH_14 -> ETH RxD2
- * ETH_15 -> ETH RxD3
- * ETH_16 -> ETH Rxerr
- * ETH_17 -> ETH CRS
- *
- * [9:11] = 111
- * SPI on PSC6
- * PSC6_0 -> MISO
- * PSC6_1 -> SS#
- * PSC6_2 -> MOSI
- * PSC6_3 -> CLK
- *
- * [8] = 0
- * IrDA/USB 48MHz clock generated internally
- *
- * [6:7] = 01
- * ATA chip selects on csb_4/5
- * CSB_4 -> ATA_CS0 out
- * CSB_5 -> ATA_CS1 out
- *
- * [5] = 1
- * PSC3_4 is used as CS6
- *
- * [4] = 1
- * PSC3_5 is used as CS7
- *
- * [2:3] = 00
- * No Alternatives
- *
- * [1] = 0
- * gpio_wkup_7 is GPIO
- *
- * [0] = 0
- * gpio_wkup_6 is GPIO
- *
- */
-#define CONFIG_SYS_GPS_PORT_CONFIG	0x0d75a162
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory */
-#define CONFIG_SYS_PROMPT "uboot> "		/* Monitor Command Prompt */
-
-#define CONFIG_CMDLINE_EDITING 1		/* add command line history */
-
-#define CONFIG_SYS_CACHELINE_SIZE 32		/* For MPC5xxx CPUs */
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CACHELINE_SHIFT 5		/* log base 2 of the above value */
-#endif
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE 1024			/* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE 512			/* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
-						/* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS 32			/* max number of command args */
-#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
-
-#define CONFIG_SYS_MEMTEST_START 0x00100000	/* memtest works on */
-#define CONFIG_SYS_MEMTEST_END 0x00f00000	/* 1 ... 15 MB in DRAM */
-
-#define CONFIG_SYS_LOAD_ADDR 0x400000		/* default load address */
-
-#define CONFIG_DISPLAY_BOARDINFO 1
-
-#define CONFIG_SYS_HUSH_PARSER 1
-
-#define CONFIG_CRC32_VERIFY  1
-
-#define CONFIG_BOOTP_DNS
-#define CONFIG_BOOTP_DNS2
-#define CONFIG_BOOTP_SEND_HOSTNAME
-
-#define CONFIG_VERSION_VARIABLE 1
-
-/*
- * Various low-level settings
- */
-#define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
-#define CONFIG_SYS_HID0_FINAL		HID0_ICE
-
-/* no burst access on the LPB */
-#define CONFIG_SYS_CS_BURST		0x00000000
-/* one deadcycle for the 33MHz statemachine */
-#define CONFIG_SYS_CS_DEADCYCLE		0x33333331
-
-#define CONFIG_SYS_BOOTCS_CFG		0x0002d900
-#define CONFIG_SYS_BOOTCS_START		CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
-
-#define CONFIG_SYS_RESET_ADDRESS	0xff000000
-
-/*
- * USB settings
- */
-#define CONFIG_USB_CLOCK		0x0001bbbb
-/* USB is on PSC3 */
-#define CONFIG_PSC3_USB
-#define CONFIG_USB_CONFIG		0x00000100
-#define CONFIG_USB_OHCI
-#define CONFIG_USB_STORAGE
-
-/*
- * IDE/ATA stuff Supports IDE harddisk
- */
-#undef  CONFIG_IDE_8xx_PCCARD	/* Use IDE with PC Card Adapter */
-#undef	CONFIG_IDE_8xx_DIRECT	/* Direct IDE not supported */
-#undef	CONFIG_IDE_LED		/* LED for ide not supported */
-
-#define	CONFIG_IDE_RESET 1	/* reset for ide supported */
-#define CONFIG_IDE_PREINIT
-#define CONFIG_SYS_IDE_MAXBUS 1	/* max. 1 IDE bus */
-#define CONFIG_SYS_IDE_MAXDEVICE 2	/* max. 2 drives per IDE bus */
-#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
-#define CONFIG_SYS_ATA_BASE_ADDR	MPC5XXX_ATA
-/* Offset for data I/O			*/
-#define CONFIG_SYS_ATA_DATA_OFFSET	(0x0060)
-/* Offset for normal register accesses	*/
-#define CONFIG_SYS_ATA_REG_OFFSET	(CONFIG_SYS_ATA_DATA_OFFSET)
-/* Offset for alternate registers	*/
-#define CONFIG_SYS_ATA_ALT_OFFSET	(0x005C)
-/* Interval between registers */
-#define CONFIG_SYS_ATA_STRIDE		4
-#define CONFIG_ATAPI			1
-
-/* we enable IDE and FAT support, so we also need partition support */
-#define CONFIG_DOS_PARTITION 1
-
-/*
- * Open Firmware flat tree
- */
-#define CONFIG_OF_LIBFDT		1
-#define CONFIG_OF_BOARD_SETUP		1
-
-#define OF_CPU				"PowerPC,5200@0"
-#define OF_TBCLK			CONFIG_SYS_MPC5XXX_CLKIN
-#define OF_SOC				"soc5200@f0000000"
-#define OF_STDOUT_PATH			"/soc5200@f0000000/serial@2600"
-
-#endif /* __CONFIG_H */