ppc4xx: Add NAND booting support for AMCC Acadia (405EZ) eval board

This patch adds NAND booting support for the AMCC Acadia eval board.

Please make sure to configure jumper J7 to position 2-3 when booting
from NOR, and to position 1-2 when booting for NAND.

I also added a board command to configure the I2C bootstrap EEPROM
values. Right now only 267MHz is support for booting either via NOR
or NAND FLASH. Here the usage:

=> bootstrap 267 nor	;to configure the board for 267MHz NOR booting
=> bootstrap 267 nand	;to configure the board for 267MHz NNAND booting

Signed-off-by: Stefan Roese <sr@denx.de>

1 files changed, 119 insertions, 33 deletions

diff --git a/include/configs/acadia.h b/include/configs/acadia.h
index c72d933..0f447b0 100644
--- a/include/configs/acadia.h
+++ b/include/configs/acadia.h
@@ -109,6 +109,7 @@
 /*-----------------------------------------------------------------------
  * FLASH related
  *----------------------------------------------------------------------*/
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
 #define CFG_FLASH_CFI			/* The flash is CFI compatible	*/
 #define CFG_FLASH_CFI_DRIVER		/* Use common CFI driver	*/
 
@@ -122,6 +123,12 @@
 #define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
 #define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
+#define	_CFG_CMD_INCLUDE	(CFG_CMD_ALL)
+#else
+#define	CFG_NO_FLASH		1	/* No NOR on Acadia when NAND-booting	*/
+#define	_CFG_CMD_INCLUDE	((CFG_CMD_ALL) & ~(CFG_CMD_FLASH | CFG_CMD_IMLS))
+#endif
+
 #ifdef CFG_ENV_IS_IN_FLASH
 #define CFG_ENV_SECT_SIZE	0x40000 /* size of one complete sector	*/
 #define CFG_ENV_ADDR		(CFG_MONITOR_BASE-CFG_ENV_SECT_SIZE)
@@ -132,6 +139,63 @@
 #define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
 #endif
 
+/*
+ * IPL (Initial Program Loader, integrated inside CPU)
+ * Will load first 4k from NAND (SPL) into cache and execute it from there.
+ *
+ * SPL (Secondary Program Loader)
+ * Will load special U-Boot version (NUB) from NAND and execute it. This SPL
+ * has to fit into 4kByte. It sets up the CPU and configures the SDRAM
+ * controller and the NAND controller so that the special U-Boot image can be
+ * loaded from NAND to SDRAM.
+ *
+ * NUB (NAND U-Boot)
+ * This NAND U-Boot (NUB) is a special U-Boot version which can be started
+ * from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
+ *
+ * On 440EPx the SPL is copied to SDRAM before the NAND controller is
+ * set up. While still running from cache, I experienced problems accessing
+ * the NAND controller.	sr - 2006-08-25
+ */
+#define CFG_NAND_BOOT_SPL_SRC	0xfffff000	/* SPL location			*/
+#define CFG_NAND_BOOT_SPL_SIZE	(4 << 10)	/* SPL size			*/
+#define CFG_NAND_BOOT_SPL_DST	(CFG_OCM_DATA_ADDR + (12 << 10)) /* Copy SPL here*/
+#define CFG_NAND_U_BOOT_DST	0x01000000	/* Load NUB to this addr	*/
+#define CFG_NAND_U_BOOT_START	CFG_NAND_U_BOOT_DST /* Start NUB from this addr	*/
+#define CFG_NAND_BOOT_SPL_DELTA	(CFG_NAND_BOOT_SPL_SRC - CFG_NAND_BOOT_SPL_DST)
+
+/*
+ * Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
+ */
+#define CFG_NAND_U_BOOT_OFFS	(16 << 10)	/* Offset to RAM U-Boot image	*/
+#define CFG_NAND_U_BOOT_SIZE	(384 << 10)	/* Size of RAM U-Boot image	*/
+
+/*
+ * Now the NAND chip has to be defined (no autodetection used!)
+ */
+#define CFG_NAND_PAGE_SIZE	512		/* NAND chip page size		*/
+#define CFG_NAND_BLOCK_SIZE	(16 << 10)	/* NAND chip block size		*/
+#define CFG_NAND_PAGE_COUNT	32		/* NAND chip page count		*/
+#define CFG_NAND_BAD_BLOCK_POS	5		/* Location of bad block marker	*/
+#undef CFG_NAND_4_ADDR_CYCLE			/* No fourth addr used (<=32MB)	*/
+
+#define CFG_NAND_ECCSIZE	256
+#define CFG_NAND_ECCBYTES	3
+#define CFG_NAND_ECCSTEPS	(CFG_NAND_PAGE_SIZE / CFG_NAND_ECCSIZE)
+#define CFG_NAND_OOBSIZE	16
+#define CFG_NAND_ECCTOTAL	(CFG_NAND_ECCBYTES * CFG_NAND_ECCSTEPS)
+#define CFG_NAND_ECCPOS		{0, 1, 2, 3, 6, 7}
+
+#ifdef CFG_ENV_IS_IN_NAND
+/*
+ * For NAND booting the environment is embedded in the U-Boot image. Please take
+ * look at the file board/amcc/sequoia/u-boot-nand.lds for details.
+ */
+#define CFG_ENV_SIZE		CFG_NAND_BLOCK_SIZE
+#define CFG_ENV_OFFSET		(CFG_NAND_U_BOOT_OFFS + CFG_ENV_SIZE)
+#define CFG_ENV_OFFSET_REDUND	(CFG_ENV_OFFSET + CFG_ENV_SIZE)
+#endif
+
 /*-----------------------------------------------------------------------
  * RAM (CRAM)
  *----------------------------------------------------------------------*/
@@ -209,7 +273,11 @@
 	"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;"	\
 		"cp.b ${fileaddr} fffc0000 ${filesize};"		\
 		"setenv filesize;saveenv\0"				\
-	"upd=run load;run update\0"					\
+	"upd=run load update\0"						\
+	"nload=tftp 200000 acadia/u-boot-nand.bin\0"			\
+	"nupdate=nand erase 0 60000;nand write 200000 0 60000;"		\
+		"setenv filesize;saveenv\0"				\
+	"nupd=run nload nupdate\0"					\
 	"kozio=bootm ffc60000\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
@@ -233,24 +301,24 @@
 
 #define CONFIG_SUPPORT_VFAT
 
-#define CONFIG_COMMANDS       (CONFIG_CMD_DFL	|	\
-			       CFG_CMD_ASKENV	|	\
-			       CFG_CMD_DHCP	|	\
-			       CFG_CMD_DTT	|	\
-			       CFG_CMD_DIAG	|	\
-			       CFG_CMD_EEPROM	|	\
-			       CFG_CMD_ELF	|	\
-			       CFG_CMD_FAT	|	\
-			       CFG_CMD_I2C	|	\
-			       CFG_CMD_IRQ	|	\
-			       CFG_CMD_MII	|	\
-			       CFG_CMD_NAND	|	\
-			       CFG_CMD_NET	|	\
-			       CFG_CMD_NFS	|	\
-			       CFG_CMD_PCI	|	\
-			       CFG_CMD_PING	|	\
-			       CFG_CMD_REGINFO	|	\
-			       CFG_CMD_USB)
+#define CONFIG_COMMANDS	((CONFIG_CMD_DFL & _CFG_CMD_INCLUDE)	|	\
+			 CFG_CMD_ASKENV	|				\
+			 CFG_CMD_DHCP	|				\
+			 CFG_CMD_DTT	|				\
+			 CFG_CMD_DIAG	|				\
+			 CFG_CMD_EEPROM	|				\
+			 CFG_CMD_ELF	|				\
+			 CFG_CMD_FAT	|				\
+			 CFG_CMD_I2C	|				\
+			 CFG_CMD_IRQ	|				\
+			 CFG_CMD_MII	|				\
+			 CFG_CMD_NAND	|				\
+			 CFG_CMD_NET	|				\
+			 CFG_CMD_NFS	|				\
+			 CFG_CMD_PCI	|				\
+			 CFG_CMD_PING	|				\
+			 CFG_CMD_REGINFO |				\
+			 CFG_CMD_USB)
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
@@ -312,12 +380,16 @@
 /*-----------------------------------------------------------------------
  * External Bus Controller (EBC) Setup
  *----------------------------------------------------------------------*/
-#define CFG_NAND_CS		3		/* NAND chip connected to CSx	*/
-
+#if !defined(CONFIG_NAND_U_BOOT) && !defined(CONFIG_NAND_SPL)
+#define CFG_NAND_CS		3
 /* Memory Bank 0 (Flash) initialization						*/
 #define CFG_EBC_PB0AP		0x03337200
 #define CFG_EBC_PB0CR		0xfe0bc000
 
+/* Memory Bank 3 (NAND-FLASH) initialization					*/
+#define CFG_EBC_PB3AP		0x018003c0
+#define CFG_EBC_PB3CR		(CFG_NAND_ADDR | 0x1c000)
+
 /* Just initial configuration for CRAM. Will be changed in memory.c to sync mode*/
 /* Memory Bank 1 (CRAM) initialization						*/
 #define CFG_EBC_PB1AP		0x030400c0
@@ -326,10 +398,24 @@
 /* Memory Bank 2 (CRAM) initialization						*/
 #define CFG_EBC_PB2AP		0x030400c0
 #define CFG_EBC_PB2CR		0x020bc000
+#else
+#define CFG_NAND_CS		0		/* NAND chip connected to CSx	*/
+/* Memory Bank 0 (NAND-FLASH) initialization					*/
+#define CFG_EBC_PB0AP		0x018003c0
+#define CFG_EBC_PB0CR		(CFG_NAND_ADDR | 0x1c000)
 
-/* Memory Bank 3 (NAND-FLASH) initialization					*/
-#define CFG_EBC_PB3AP		0x018003c0
-#define CFG_EBC_PB3CR		(CFG_NAND_ADDR | 0x1c000)
+/*
+ * When NAND-booting the CRAM EBC setup must be done in sync mode, since the
+ * NAND-SPL already initialized the CRAM and EBC to sync mode.
+ */
+/* Memory Bank 1 (CRAM) initialization						*/
+#define CFG_EBC_PB1AP		0x9C0201C0
+#define CFG_EBC_PB1CR		0x000bc000
+
+/* Memory Bank 2 (CRAM) initialization						*/
+#define CFG_EBC_PB2AP		0x9C0201C0
+#define CFG_EBC_PB2CR		0x020bc000
+#endif
 
 /* Memory Bank 4 (CPLD) initialization						*/
 #define CFG_EBC_PB4AP		0x04006000
@@ -341,9 +427,9 @@
  * GPIO Setup
  *----------------------------------------------------------------------*/
 #define CFG_GPIO_CRAM_CLK	8
-#define CFG_GPIO_CRAM_WAIT	9
+#define CFG_GPIO_CRAM_WAIT	9		/* GPIO-In		*/
 #define CFG_GPIO_CRAM_ADV	10
-#define CFG_GPIO_CRAM_CRE	(32 + 21)
+#define CFG_GPIO_CRAM_CRE	(32 + 21)	/* GPIO-Out		*/
 
 /*-----------------------------------------------------------------------
  * Definitions for GPIO_0 setup (PPC405EZ specific)
@@ -365,10 +451,10 @@
  * GPIO0[28-30]	- Trace Outputs / PWM Inputs
  * GPIO0[31]	- PWM_8 I/O
  */
-#define CFG_GPIO0_TCR		0xC0000000
-#define CFG_GPIO0_OSRL		0x50000000
+#define CFG_GPIO0_TCR		0xC0A00000
+#define CFG_GPIO0_OSRL		0x50004400
 #define CFG_GPIO0_OSRH		0x02000055
-#define CFG_GPIO0_ISR1L		0x00000000
+#define CFG_GPIO0_ISR1L		0x00001000
 #define CFG_GPIO0_ISR1H		0x00000055
 #define CFG_GPIO0_TSRL		0x02000000
 #define CFG_GPIO0_TSRH		0x00000055
@@ -387,13 +473,13 @@
  * GPIO1[16]	- SPI_SS_1_N Output
  * GPIO1[17-20]	- Trace Output/External Interrupts IRQ0 - IRQ3 inputs
  */
-#define CFG_GPIO1_OSRH		0x55455555
+#define CFG_GPIO1_TCR		0xFFFF8414
 #define CFG_GPIO1_OSRL		0x40000110
-#define CFG_GPIO1_ISR1H		0x00000000
+#define CFG_GPIO1_OSRH		0x55455555
 #define CFG_GPIO1_ISR1L		0x15555445
-#define CFG_GPIO1_TSRH		0x00000000
+#define CFG_GPIO1_ISR1H		0x00000000
 #define CFG_GPIO1_TSRL		0x00000000
-#define CFG_GPIO1_TCR		0xFFFF8014
+#define CFG_GPIO1_TSRH		0x00000000
 
 /*
  * Internal Definitions