rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

1 files changed, 79 insertions, 79 deletions

diff --git a/include/configs/W7OLMG.h b/include/configs/W7OLMG.h
index c3b39f2..2260338 100644
--- a/include/configs/W7OLMG.h
+++ b/include/configs/W7OLMG.h
@@ -63,7 +63,7 @@
 #define CONFIG_SERVERIP		192.168.1.2
 
 #define CONFIG_LOADS_ECHO	1		/* echo on for serial download	*/
-#undef CFG_LOADS_BAUD_CHANGE			/* disallow baudrate change	*/
+#undef CONFIG_SYS_LOADS_BAUD_CHANGE			/* disallow baudrate change	*/
 
 #define CONFIG_MII		1		/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		0		/* PHY address			*/
@@ -71,9 +71,9 @@
 #define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
 #define CONFIG_DTT_LM75     1                /* ON Semi's LM75 */
 #define CONFIG_DTT_SENSORS  {2, 4}           /* Sensor addresses */
-#define CFG_DTT_MAX_TEMP	70
-#define CFG_DTT_LOW_TEMP	-30
-#define CFG_DTT_HYSTERESIS	3
+#define CONFIG_SYS_DTT_MAX_TEMP	70
+#define CONFIG_SYS_DTT_LOW_TEMP	-30
+#define CONFIG_SYS_DTT_HYSTERESIS	3
 
 
 /*
@@ -112,38 +112,38 @@
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP				/* undef to save memory		*/
-#define CFG_PROMPT		"Wave7Optics> " /* Monitor Command Prompt	*/
-#undef  CFG_HUSH_PARSER				/* No hush parse for U-Boot       */
-#ifdef  CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2     "> "
+#define CONFIG_SYS_LONGHELP				/* undef to save memory		*/
+#define CONFIG_SYS_PROMPT		"Wave7Optics> " /* Monitor Command Prompt	*/
+#undef  CONFIG_SYS_HUSH_PARSER				/* No hush parse for U-Boot       */
+#ifdef  CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 #endif
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE		1024		/* Console I/O Buffer Size	*/
 #else
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size	*/
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size	*/
+#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on		*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/
+#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on		*/
+#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM		*/
 
-#undef  CFG_EXT_SERIAL_CLOCK			/* external serial clock */
-#define CFG_405_UART_ERRATA_59			/* 405GP/CR Rev. D silicon */
-#define CFG_BASE_BAUD		384000
+#undef  CONFIG_SYS_EXT_SERIAL_CLOCK			/* external serial clock */
+#define CONFIG_SYS_405_UART_ERRATA_59			/* 405GP/CR Rev. D silicon */
+#define CONFIG_SYS_BASE_BAUD		384000
 
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE	{9600}
+#define CONFIG_SYS_BAUDRATE_TABLE	{9600}
 
-#define CFG_CLKS_IN_HZ		1		/* everything, incl board info, in Hz */
+#define CONFIG_SYS_CLKS_IN_HZ		1		/* everything, incl board info, in Hz */
 
-#define CFG_LOAD_ADDR		0x100000	/* default load address		*/
-#define CFG_EXTBDINFO		1		/* use extended board_info (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address		*/
+#define CONFIG_SYS_EXTBDINFO		1		/* use extended board_info (bd_t) */
 
-#define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ			1000		/* decrementer freq: 1 ms ticks */
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -157,14 +157,14 @@
 #define CONFIG_PCI_HOST		PCI_HOST_AUTO	/* select pci host function	*/
 #define CONFIG_PCI_PNP				/* pci plug-and-play		*/
 /* resource configuration	*/
-#define CFG_PCI_SUBSYS_VENDORID 0x1014		/* PCI Vendor ID: IBM		*/
-#define CFG_PCI_SUBSYS_DEVICEID 0x0156		/* PCI Device ID: 405GP		*/
-#define CFG_PCI_PTM1LA		0x00000000	/* point to sdram		*/
-#define CFG_PCI_PTM1MS		0x80000001	/* 2GB, enable hard-wired to 1	*/
-#define CFG_PCI_PTM1PCI		0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA		0x00000000	/* disabled			*/
-#define CFG_PCI_PTM2MS		0x00000000	/* disabled			*/
-#define CFG_PCI_PTM2PCI		0x00000000      /* Host: use this pci address   */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1014		/* PCI Vendor ID: IBM		*/
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0156		/* PCI Device ID: 405GP		*/
+#define CONFIG_SYS_PCI_PTM1LA		0x00000000	/* point to sdram		*/
+#define CONFIG_SYS_PCI_PTM1MS		0x80000001	/* 2GB, enable hard-wired to 1	*/
+#define CONFIG_SYS_PCI_PTM1PCI		0x00000000      /* Host: use this pci address   */
+#define CONFIG_SYS_PCI_PTM2LA		0x00000000	/* disabled			*/
+#define CONFIG_SYS_PCI_PTM2MS		0x00000000	/* disabled			*/
+#define CONFIG_SYS_PCI_PTM2PCI		0x00000000      /* Host: use this pci address   */
 
 /*-----------------------------------------------------------------------
  * Set up values for external bus controller
@@ -175,94 +175,94 @@
 #define CONFIG_USE_PERWE 1
 
 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM        1
+#define CONFIG_SYS_TEMP_STACK_OCM        1
 
 /* bank 0 is boot flash */
 /* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
-#define CFG_W7O_EBC_PB0AP   0x03050440
+#define CONFIG_SYS_W7O_EBC_PB0AP   0x03050440
 /* BAS=0xFFE,BS=0x1(2MB),BU=0x3(R/W),BW=0x0(8 bits) */
-#define CFG_W7O_EBC_PB0CR   0xFFE38000
+#define CONFIG_SYS_W7O_EBC_PB0CR   0xFFE38000
 
 /* bank 1 is main flash */
 /* BME=0,TWT=9,CSN=1,OEN=1,WBN=0,WBF=0,TH=1,RE=0,SOR=0,BEM=1,PEN=0 */
-#define CFG_EBC_PB1AP   0x04850240
+#define CONFIG_SYS_EBC_PB1AP   0x04850240
 /* BAS=0xF00,BS=0x7(128MB),BU=0x3(R/W),BW=0x10(32 bits) */
-#define CFG_EBC_PB1CR   0xF00FC000
+#define CONFIG_SYS_EBC_PB1CR   0xF00FC000
 
 /* bank 2 is RTC/NVRAM */
 /* BME=0,TWT=6,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
-#define CFG_EBC_PB2AP   0x03000440
+#define CONFIG_SYS_EBC_PB2AP   0x03000440
 /* BAS=0xFC0,BS=0x0(1MB),BU=0x3(R/W),BW=0x0(8 bits) */
-#define CFG_EBC_PB2CR   0xFC018000
+#define CONFIG_SYS_EBC_PB2CR   0xFC018000
 
 /* bank 3 is FPGA 0 */
 /* BME=0,TWT=4,CSN=0,OEN=0,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=0,PEN=0 */
-#define CFG_EBC_PB3AP   0x02000400
+#define CONFIG_SYS_EBC_PB3AP   0x02000400
 /* BAS=0xFD0,BS=0x0(1MB),BU=0x3(R/W),BW=0x1(16 bits) */
-#define CFG_EBC_PB3CR   0xFD01A000
+#define CONFIG_SYS_EBC_PB3CR   0xFD01A000
 
 /* bank 4 is SAM 8 bit range */
 /* BME=,TWT=,CSN=,OEN=,WBN=,WBF=,TH=,RE=,SOR=,BEM=,PEN= */
-#define CFG_EBC_PB4AP   0x02840380
+#define CONFIG_SYS_EBC_PB4AP   0x02840380
 /* BAS=,BS=,BU=0x3(R/W),BW=0x0(8 bits) */
-#define CFG_EBC_PB4CR   0xFE878000
+#define CONFIG_SYS_EBC_PB4CR   0xFE878000
 
 /* bank 5 is SAM 16 bit range */
 /* BME=0,TWT=10,CSN=2,OEN=0,WBN=0,WBF=0,TH=6,RE=1,SOR=1,BEM=0,PEN=0 */
-#define CFG_EBC_PB5AP   0x05040d80
+#define CONFIG_SYS_EBC_PB5AP   0x05040d80
 /* BAS=,BS=,BU=0x3(R/W),BW=0x1(16 bits) */
-#define CFG_EBC_PB5CR   0xFD87A000
+#define CONFIG_SYS_EBC_PB5CR   0xFD87A000
 
 /* bank 6 is unused */
 /* pb6ap = 0 */
-#define CFG_EBC_PB6AP   0x00000000
+#define CONFIG_SYS_EBC_PB6AP   0x00000000
 /* pb6cr = 0 */
-#define CFG_EBC_PB6CR   0x00000000
+#define CONFIG_SYS_EBC_PB6CR   0x00000000
 
 /* bank 7 is LED register */
 /* BME=0,TWT=6,CSN=1,OEN=1,WBN=0,WBF=0,TH=2,RE=0,SOR=0,BEM=1,PEN=0 */
-#define CFG_W7O_EBC_PB7AP   0x03050440
+#define CONFIG_SYS_W7O_EBC_PB7AP   0x03050440
 /* BAS=0xFE0,BS=0x0(1MB),BU=0x3(R/W),BW=0x2(32 bits) */
-#define CFG_W7O_EBC_PB7CR   0xFE01C000
+#define CONFIG_SYS_W7O_EBC_PB7CR   0xFE01C000
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_FLASH_BASE		0xFFFC0000
-#define CFG_MONITOR_BASE	CFG_FLASH_BASE
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 196 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		0xFFFC0000
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 196 kB for Monitor	*/
+#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	2		/* max number of memory banks	*/
-#define CFG_MAX_FLASH_SECT	256		/* max number of sec on 1 chip	*/
+#define CONFIG_SYS_MAX_FLASH_BANKS	2		/* max number of memory banks	*/
+#define CONFIG_SYS_MAX_FLASH_SECT	256		/* max number of sec on 1 chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000		/* Timeout, Flash Erase, in ms	*/
-#define CFG_FLASH_WRITE_TOUT	500		/* Timeout, Flash Write, in ms	*/
-#define CFG_FLASH_PROTECTION	1		/* Use real Flash protection	*/
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000		/* Timeout, Flash Erase, in ms	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500		/* Timeout, Flash Write, in ms	*/
+#define CONFIG_SYS_FLASH_PROTECTION	1		/* Use real Flash protection	*/
 
 #if 1 /* Use NVRAM for environment variables */
 /*-----------------------------------------------------------------------
  * NVRAM organization
  */
 #define CONFIG_ENV_IS_IN_NVRAM	1		/* use NVRAM for env vars	*/
-#define CFG_NVRAM_BASE_ADDR	0xfc000000	/* NVRAM base address		*/
-#define CFG_NVRAM_SIZE		(32*1024)	/* NVRAM size			*/
+#define CONFIG_SYS_NVRAM_BASE_ADDR	0xfc000000	/* NVRAM base address		*/
+#define CONFIG_SYS_NVRAM_SIZE		(32*1024)	/* NVRAM size			*/
 #define CONFIG_ENV_SIZE		0x1000		/* Size of Environment vars	*/
 /*define CONFIG_ENV_ADDR		 \
-	(CFG_NVRAM_BASE_ADDR+CFG_NVRAM_SIZE-CONFIG_ENV_SIZE) Env  */
-#define CONFIG_ENV_ADDR		CFG_NVRAM_BASE_ADDR
+	(CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) Env  */
+#define CONFIG_ENV_ADDR		CONFIG_SYS_NVRAM_BASE_ADDR
 
 #else /* Use Boot Flash for environment variables */
 /*-----------------------------------------------------------------------
@@ -279,13 +279,13 @@
  * I2C EEPROM (ATMEL 24C04N)
  */
 #define CONFIG_HARD_I2C		1		/* Hardware assisted I2C	*/
-#define CFG_I2C_SPEED		400000		/* I2C speed and slave address */
-#define CFG_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
 
-#define CFG_I2C_EEPROM_ADDR	0x50		/* EEPROM ATMEL 24C04N		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	1		/* Bytes of address		*/
-#define CFG_EEPROM_PAGE_WRITE_BITS 3
-#define CFG_I2C_MULTI_EEPROMS
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50		/* EEPROM ATMEL 24C04N		*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1		/* Bytes of address		*/
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
+#define CONFIG_SYS_I2C_MULTI_EEPROMS
 /*-----------------------------------------------------------------------
  * Definitions for Serial Presence Detect EEPROM address
  * (to get SDRAM settings)
@@ -299,17 +299,17 @@
 #define FLASH_BASE1_PRELIM	0xF0000000	/* FLASH bank #1		*/
 
 /* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR	0xF8000000
-#define CFG_OCM_DATA_SIZE	0x1000
+#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in RAM)
  */
-#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
-#define CFG_GBL_DATA_SIZE	64		/* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
+#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM	*/
+#define CONFIG_SYS_GBL_DATA_SIZE	64		/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 
 /*
@@ -328,7 +328,7 @@
 /*
  * FPGA(s) configuration
  */
-#define CFG_FPGA_IMAGE_LEN	0x80000		/* 512KB FPGA image		*/
+#define CONFIG_SYS_FPGA_IMAGE_LEN	0x80000		/* 512KB FPGA image		*/
 #define CONFIG_NUM_FPGAS	1		/* Number of FPGAs on board	*/
 #define CONFIG_MAX_FPGAS	6		/* Maximum number of FPGAs	*/
 #define CONFIG_FPGAS_BASE	0xFD000000L	/* Base address of FPGAs	*/