powerpc/t2081qds: Add T2081 QDS board support

T2081 QDS is a high-performance computing evaluation, development and
test platform supporting the T2081 QorIQ Power Architecture processor.

T2081QDS board Overview
-----------------------
- T2081 SoC integrating four 64-bit dual-threads e6500 cores up to 1.8GHz
- 2MB shared L2 and 512KB L3 CoreNet platform cache (CPC)
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- 32-/64-bit DDR3/DDR3LP SDRAM memory controller with ECC and interleaving
- Ethernet interfaces:
  - Two on-board 10M/100M/1G bps RGMII ports
  - Two 10Gbps XFI with on-board SFP+ cage
  - 1Gbps/2.5Gbps SGMII Riser card
  - 10Gbps XAUI Riser card
- Accelerator:
  - DPAA components consist of FMan, BMan, QMan, PME, DCE and SEC
- SerDes:
  - 8 lanes up to 10.3125GHz
  - Supports SGMII, HiGig, XFI, XAUI and Aurora debug,
- IFC:
  - 512MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- eSPI:
  - Three SPI flash (16MB N25Q128A + 16MB EN25S64 + 512KB SST25WF040)
- USB:
  - Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- PCIe:
  - Four PCI Express controllers (two PCIe 2.0 and two PCIe 3.0 with SR-IOV)
- eSDHC:
  - Supports various SD/SDHC/SDXC/eMMC devices with adapter cards and
    voltage translators
- I2C:
  - Four I2C controllers.
- UART:
  - Dual 4-pins UART serial ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>

1 files changed, 0 insertions, 804 deletions

diff --git a/include/configs/T2080QDS.h b/include/configs/T2080QDS.h
deleted file mode 100644
index 9bd0fe2..0000000
--- a/include/configs/T2080QDS.h
+++ /dev/null
@@ -1,804 +0,0 @@
-/*
- * Copyright 2011-2013 Freescale Semiconductor, Inc.
- *
- * SPDX-License-Identifier:     GPL-2.0+
- */
-
-/*
- * T2080 QDS board configuration file
- */
-
-#ifndef __T2080QDS_H
-#define __T2080QDS_H
-
-#define CONFIG_T2080QDS
-#define CONFIG_ICS307_REFCLK_HZ 25000000  /* ICS307 ref clk freq */
-#define CONFIG_MMC
-#define CONFIG_SPI_FLASH
-#define CONFIG_USB_EHCI
-#define CONFIG_FSL_SATA_V2
-#define CONFIG_SYS_SRIO		/* Enable Serial RapidIO Support */
-#define CONFIG_SRIO1		/* SRIO port 1 */
-#define CONFIG_SRIO2		/* SRIO port 2 */
-
-/* High Level Configuration Options */
-#define CONFIG_PHYS_64BIT
-#define CONFIG_BOOKE
-#define CONFIG_E500		/* BOOKE e500 family */
-#define CONFIG_E500MC		/* BOOKE e500mc family */
-#define CONFIG_SYS_BOOK3E_HV	/* Category E.HV supported */
-#define CONFIG_MP		/* support multiple processors */
-#define CONFIG_ENABLE_36BIT_PHYS
-
-#ifdef CONFIG_PHYS_64BIT
-#define CONFIG_ADDR_MAP 1
-#define CONFIG_SYS_NUM_ADDR_MAP 64 /* number of TLB1 entries */
-#endif
-
-#define CONFIG_SYS_FSL_CPC	/* Corenet Platform Cache */
-#define CONFIG_SYS_NUM_CPC	CONFIG_NUM_DDR_CONTROLLERS
-#define CONFIG_FSL_IFC		/* Enable IFC Support */
-#define CONFIG_FSL_LAW		/* Use common FSL init code */
-#define CONFIG_ENV_OVERWRITE
-
-#ifdef CONFIG_RAMBOOT_PBL
-#define CONFIG_RAMBOOT_TEXT_BASE	CONFIG_SYS_TEXT_BASE
-#define CONFIG_RESET_VECTOR_ADDRESS	0xfffffffc
-#define CONFIG_SYS_FSL_PBL_PBI $(SRCTREE)/board/freescale/t2080qds/t2080_pbi.cfg
-#define CONFIG_SYS_FSL_PBL_RCW $(SRCTREE)/board/freescale/t2080qds/t2080_rcw.cfg
-#endif
-
-#define CONFIG_SRIO_PCIE_BOOT_MASTER
-#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
-/* Set 1M boot space */
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR (CONFIG_SYS_TEXT_BASE & 0xfff00000)
-#define CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR_PHYS \
-		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_SLAVE_ADDR)
-#define CONFIG_RESET_VECTOR_ADDRESS 0xfffffffc
-#define CONFIG_SYS_NO_FLASH
-#endif
-
-#ifndef CONFIG_SYS_TEXT_BASE
-#define CONFIG_SYS_TEXT_BASE	0xeff40000
-#endif
-
-#ifndef CONFIG_RESET_VECTOR_ADDRESS
-#define CONFIG_RESET_VECTOR_ADDRESS	0xeffffffc
-#endif
-
-/*
- * These can be toggled for performance analysis, otherwise use default.
- */
-#define CONFIG_SYS_CACHE_STASHING
-#define CONFIG_BTB		/* toggle branch predition */
-#define CONFIG_DDR_ECC
-#ifdef CONFIG_DDR_ECC
-#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
-#define CONFIG_MEM_INIT_VALUE		0xdeadbeef
-#endif
-
-#ifdef CONFIG_SYS_NO_FLASH
-#if !defined(CONFIG_SRIO_PCIE_BOOT_SLAVE) && !defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_ENV_IS_NOWHERE
-#endif
-#else
-#define CONFIG_FLASH_CFI_DRIVER
-#define CONFIG_SYS_FLASH_CFI
-#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
-#endif
-
-#if defined(CONFIG_SPIFLASH)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_SPI_FLASH
-#define CONFIG_ENV_SPI_BUS	0
-#define CONFIG_ENV_SPI_CS	0
-#define CONFIG_ENV_SPI_MAX_HZ	10000000
-#define CONFIG_ENV_SPI_MODE	0
-#define CONFIG_ENV_SIZE		0x2000	   /* 8KB */
-#define CONFIG_ENV_OFFSET	0x100000   /* 1MB */
-#define CONFIG_ENV_SECT_SIZE	0x10000
-#elif defined(CONFIG_SDCARD)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_MMC
-#define CONFIG_SYS_MMC_ENV_DEV	0
-#define CONFIG_ENV_SIZE		0x2000
-#define CONFIG_ENV_OFFSET	(512 * 1658)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_EXTRA_ENV_RELOC
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SIZE		CONFIG_SYS_NAND_BLOCK_SIZE
-#define CONFIG_ENV_OFFSET	(7 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-#define CONFIG_ENV_IS_IN_REMOTE
-#define CONFIG_ENV_ADDR		0xffe20000
-#define CONFIG_ENV_SIZE		0x2000
-#elif defined(CONFIG_ENV_IS_NOWHERE)
-#define CONFIG_ENV_SIZE		0x2000
-#else
-#define CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
-#define CONFIG_ENV_SIZE		0x2000
-#define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
-#endif
-
-#ifndef __ASSEMBLY__
-unsigned long get_board_sys_clk(void);
-unsigned long get_board_ddr_clk(void);
-#endif
-
-#define CONFIG_SYS_CLK_FREQ	get_board_sys_clk()
-#define CONFIG_DDR_CLK_FREQ	get_board_ddr_clk()
-
-/*
- * Config the L3 Cache as L3 SRAM
- */
-#define CONFIG_SYS_INIT_L3_ADDR	 CONFIG_RAMBOOT_TEXT_BASE
-
-#define CONFIG_SYS_DCSRBAR	0xf0000000
-#define CONFIG_SYS_DCSRBAR_PHYS	0xf00000000ull
-
-/* EEPROM */
-#define CONFIG_ID_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_NXID
-#define CONFIG_SYS_EEPROM_BUS_NUM	0
-#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN	1
-
-/*
- * DDR Setup
- */
-#define CONFIG_VERY_BIG_RAM
-#define CONFIG_SYS_DDR_SDRAM_BASE	0x00000000
-#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
-#define CONFIG_DIMM_SLOTS_PER_CTLR	1
-#define CONFIG_CHIP_SELECTS_PER_CTRL	(4 * CONFIG_DIMM_SLOTS_PER_CTLR)
-#define CONFIG_DDR_SPD
-#define CONFIG_SYS_FSL_DDR3
-#undef CONFIG_FSL_DDR_INTERACTIVE
-#define CONFIG_SYS_SPD_BUS_NUM	0
-#define CONFIG_SYS_SDRAM_SIZE	2048	/* for fixed parameter use */
-#define SPD_EEPROM_ADDRESS1	0x51
-#define SPD_EEPROM_ADDRESS2	0x52
-#define SPD_EEPROM_ADDRESS	SPD_EEPROM_ADDRESS1
-#define CTRL_INTLV_PREFERED	cacheline
-
-/*
- * IFC Definitions
- */
-#define CONFIG_SYS_FLASH_BASE		0xe0000000
-#define CONFIG_SYS_FLASH_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_FLASH_BASE)
-#define CONFIG_SYS_NOR0_CSPR_EXT	(0xf)
-#define CONFIG_SYS_NOR0_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS \
-				+ 0x8000000) | \
-				CSPR_PORT_SIZE_16 | \
-				CSPR_MSEL_NOR | \
-				CSPR_V)
-#define CONFIG_SYS_NOR1_CSPR_EXT	(0xf)
-#define CONFIG_SYS_NOR1_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | \
-				CSPR_PORT_SIZE_16 | \
-				CSPR_MSEL_NOR | \
-				CSPR_V)
-#define CONFIG_SYS_NOR_AMASK	IFC_AMASK(128*1024*1024)
-/* NOR Flash Timing Params */
-#define CONFIG_SYS_NOR_CSOR	CSOR_NAND_TRHZ_80
-
-#define CONFIG_SYS_NOR_FTIM0	(FTIM0_NOR_TACSE(0x4) | \
-				FTIM0_NOR_TEADC(0x5) | \
-				FTIM0_NOR_TEAHC(0x5))
-#define CONFIG_SYS_NOR_FTIM1	(FTIM1_NOR_TACO(0x35) | \
-				FTIM1_NOR_TRAD_NOR(0x1A) |\
-				FTIM1_NOR_TSEQRAD_NOR(0x13))
-#define CONFIG_SYS_NOR_FTIM2	(FTIM2_NOR_TCS(0x4) | \
-				FTIM2_NOR_TCH(0x4) | \
-				FTIM2_NOR_TWPH(0x0E) | \
-				FTIM2_NOR_TWP(0x1c))
-#define CONFIG_SYS_NOR_FTIM3	0x0
-
-#define CONFIG_SYS_FLASH_QUIET_TEST
-#define CONFIG_FLASH_SHOW_PROGRESS	45 /* count down from 45/5: 9..1 */
-
-#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* number of banks */
-#define CONFIG_SYS_MAX_FLASH_SECT	1024	/* sectors per device */
-#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
-
-#define CONFIG_SYS_FLASH_EMPTY_INFO
-#define CONFIG_SYS_FLASH_BANKS_LIST	{CONFIG_SYS_FLASH_BASE_PHYS \
-					+ 0x8000000, CONFIG_SYS_FLASH_BASE_PHYS}
-
-#define CONFIG_FSL_QIXIS	/* use common QIXIS code */
-#define QIXIS_BASE			0xffdf0000
-#define QIXIS_LBMAP_SWITCH		6
-#define QIXIS_LBMAP_MASK		0x0f
-#define QIXIS_LBMAP_SHIFT		0
-#define QIXIS_LBMAP_DFLTBANK		0x00
-#define QIXIS_LBMAP_ALTBANK		0x04
-#define QIXIS_RST_CTL_RESET		0x83
-#define QIXIS_RST_FORCE_MEM		0x1
-#define QIXIS_RCFG_CTL_RECONFIG_IDLE	0x20
-#define QIXIS_RCFG_CTL_RECONFIG_START	0x21
-#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE	0x08
-#define QIXIS_BASE_PHYS		(0xf00000000ull | QIXIS_BASE)
-
-#define CONFIG_SYS_CSPR3_EXT	(0xf)
-#define CONFIG_SYS_CSPR3	(CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
-				| CSPR_PORT_SIZE_8 \
-				| CSPR_MSEL_GPCM \
-				| CSPR_V)
-#define CONFIG_SYS_AMASK3	IFC_AMASK(4*1024)
-#define CONFIG_SYS_CSOR3	0x0
-/* QIXIS Timing parameters for IFC CS3 */
-#define CONFIG_SYS_CS3_FTIM0		(FTIM0_GPCM_TACSE(0x0e) | \
-					FTIM0_GPCM_TEADC(0x0e) | \
-					FTIM0_GPCM_TEAHC(0x0e))
-#define CONFIG_SYS_CS3_FTIM1		(FTIM1_GPCM_TACO(0xff) | \
-					FTIM1_GPCM_TRAD(0x3f))
-#define CONFIG_SYS_CS3_FTIM2		(FTIM2_GPCM_TCS(0x0e) | \
-					FTIM2_GPCM_TCH(0x0) | \
-					FTIM2_GPCM_TWP(0x1f))
-#define CONFIG_SYS_CS3_FTIM3		0x0
-
-/* NAND Flash on IFC */
-#define CONFIG_NAND_FSL_IFC
-#define CONFIG_SYS_NAND_BASE		0xff800000
-#define CONFIG_SYS_NAND_BASE_PHYS	(0xf00000000ull | CONFIG_SYS_NAND_BASE)
-
-#define CONFIG_SYS_NAND_CSPR_EXT	(0xf)
-#define CONFIG_SYS_NAND_CSPR	(CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
-				| CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
-				| CSPR_MSEL_NAND	 /* MSEL = NAND */ \
-				| CSPR_V)
-#define CONFIG_SYS_NAND_AMASK	IFC_AMASK(64*1024)
-
-#define CONFIG_SYS_NAND_CSOR	(CSOR_NAND_ECC_ENC_EN	/* ECC on encode */ \
-				| CSOR_NAND_ECC_DEC_EN	/* ECC on decode */ \
-				| CSOR_NAND_ECC_MODE_4	/* 4-bit ECC */	    \
-				| CSOR_NAND_RAL_3	/* RAL = 2Byes */   \
-				| CSOR_NAND_PGS_2K	/* Page Size = 2K */\
-				| CSOR_NAND_SPRZ_64	/* Spare size = 64 */\
-				| CSOR_NAND_PB(64))	/*Pages Per Block = 64*/
-
-#define CONFIG_SYS_NAND_ONFI_DETECTION
-
-/* ONFI NAND Flash mode0 Timing Params */
-#define CONFIG_SYS_NAND_FTIM0		(FTIM0_NAND_TCCST(0x07) | \
-					FTIM0_NAND_TWP(0x18)    | \
-					FTIM0_NAND_TWCHT(0x07)  | \
-					FTIM0_NAND_TWH(0x0a))
-#define CONFIG_SYS_NAND_FTIM1		(FTIM1_NAND_TADLE(0x32) | \
-					FTIM1_NAND_TWBE(0x39)   | \
-					FTIM1_NAND_TRR(0x0e)    | \
-					FTIM1_NAND_TRP(0x18))
-#define CONFIG_SYS_NAND_FTIM2		(FTIM2_NAND_TRAD(0x0f)  | \
-					FTIM2_NAND_TREH(0x0a)   | \
-					FTIM2_NAND_TWHRE(0x1e))
-#define CONFIG_SYS_NAND_FTIM3		0x0
-
-#define CONFIG_SYS_NAND_DDR_LAW		11
-#define CONFIG_SYS_NAND_BASE_LIST	{ CONFIG_SYS_NAND_BASE }
-#define CONFIG_SYS_MAX_NAND_DEVICE	1
-#define CONFIG_MTD_NAND_VERIFY_WRITE
-#define CONFIG_CMD_NAND
-#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
-
-#if defined(CONFIG_NAND)
-#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR0		CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK0		CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR0		CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NAND_FTIM3
-#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR2		CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK2		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR2		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NOR_FTIM3
-#else
-#define CONFIG_SYS_CSPR0_EXT		CONFIG_SYS_NOR0_CSPR_EXT
-#define CONFIG_SYS_CSPR0		CONFIG_SYS_NOR0_CSPR
-#define CONFIG_SYS_AMASK0		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR0		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS0_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS0_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS0_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS0_FTIM3		CONFIG_SYS_NOR_FTIM3
-#define CONFIG_SYS_CSPR2_EXT		CONFIG_SYS_NAND_CSPR_EXT
-#define CONFIG_SYS_CSPR2		CONFIG_SYS_NAND_CSPR
-#define CONFIG_SYS_AMASK2		CONFIG_SYS_NAND_AMASK
-#define CONFIG_SYS_CSOR2		CONFIG_SYS_NAND_CSOR
-#define CONFIG_SYS_CS2_FTIM0		CONFIG_SYS_NAND_FTIM0
-#define CONFIG_SYS_CS2_FTIM1		CONFIG_SYS_NAND_FTIM1
-#define CONFIG_SYS_CS2_FTIM2		CONFIG_SYS_NAND_FTIM2
-#define CONFIG_SYS_CS2_FTIM3		CONFIG_SYS_NAND_FTIM3
-#endif
-#define CONFIG_SYS_CSPR1_EXT		CONFIG_SYS_NOR1_CSPR_EXT
-#define CONFIG_SYS_CSPR1		CONFIG_SYS_NOR1_CSPR
-#define CONFIG_SYS_AMASK1		CONFIG_SYS_NOR_AMASK
-#define CONFIG_SYS_CSOR1		CONFIG_SYS_NOR_CSOR
-#define CONFIG_SYS_CS1_FTIM0		CONFIG_SYS_NOR_FTIM0
-#define CONFIG_SYS_CS1_FTIM1		CONFIG_SYS_NOR_FTIM1
-#define CONFIG_SYS_CS1_FTIM2		CONFIG_SYS_NOR_FTIM2
-#define CONFIG_SYS_CS1_FTIM3		CONFIG_SYS_NOR_FTIM3
-
-#if defined(CONFIG_RAMBOOT_PBL)
-#define CONFIG_SYS_RAMBOOT
-#endif
-
-#define CONFIG_SYS_MONITOR_BASE	 CONFIG_SYS_TEXT_BASE
-#define CONFIG_BOARD_EARLY_INIT_R	/* call board_early_init_r function */
-#define CONFIG_MISC_INIT_R
-#define CONFIG_HWCONFIG
-
-/* define to use L1 as initial stack */
-#define CONFIG_L1_INIT_RAM
-#define CONFIG_SYS_INIT_RAM_LOCK
-#define CONFIG_SYS_INIT_RAM_ADDR	0xfdd00000 /* Initial L1 address */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH	0xf
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW	0xfe0ec000
-/* The assembler doesn't like typecast */
-#define CONFIG_SYS_INIT_RAM_ADDR_PHYS \
-			((CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH * 1ull << 32) | \
-			CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW)
-#define CONFIG_SYS_INIT_RAM_SIZE	0x00004000
-#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - \
-						GENERATED_GBL_DATA_SIZE)
-#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
-#define CONFIG_SYS_MALLOC_LEN		(4 * 1024 * 1024)
-
-/*
- * Serial Port
- */
-#define CONFIG_CONS_INDEX		1
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		(get_bus_freq(0)/2)
-#define CONFIG_SYS_BAUDRATE_TABLE	\
-	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200}
-#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x11C500)
-#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x11C600)
-#define CONFIG_SYS_NS16550_COM3 (CONFIG_SYS_CCSRBAR+0x11D500)
-#define CONFIG_SYS_NS16550_COM4 (CONFIG_SYS_CCSRBAR+0x11D600)
-
-/* Use the HUSH parser */
-#define CONFIG_SYS_HUSH_PARSER
-#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
-
-/* pass open firmware flat tree */
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_OF_STDOUT_VIA_ALIAS
-
-/* new uImage format support */
-#define CONFIG_FIT
-#define CONFIG_FIT_VERBOSE	/* enable fit_format_{error,warning}() */
-
-/*
- * I2C
- */
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_FSL
-#define CONFIG_SYS_FSL_I2C_SLAVE   0x7F
-#define CONFIG_SYS_FSL_I2C2_SLAVE  0x7F
-#define CONFIG_SYS_FSL_I2C3_SLAVE  0x7F
-#define CONFIG_SYS_FSL_I2C4_SLAVE  0x7F
-#define CONFIG_SYS_FSL_I2C_OFFSET  0x118000
-#define CONFIG_SYS_FSL_I2C2_OFFSET 0x118100
-#define CONFIG_SYS_FSL_I2C3_OFFSET 0x119000
-#define CONFIG_SYS_FSL_I2C4_OFFSET 0x119100
-#define CONFIG_SYS_FSL_I2C_SPEED   100000
-#define CONFIG_SYS_FSL_I2C2_SPEED  100000
-#define CONFIG_SYS_FSL_I2C3_SPEED  100000
-#define CONFIG_SYS_FSL_I2C4_SPEED  100000
-#define I2C_MUX_PCA_ADDR_PRI	0x77 /* I2C bus multiplexer,primary */
-#define I2C_MUX_PCA_ADDR_SEC1	0x75 /* I2C bus multiplexer,secondary 1 */
-#define I2C_MUX_PCA_ADDR_SEC2	0x76 /* I2C bus multiplexer,secondary 2 */
-#define I2C_MUX_CH_DEFAULT	0x8
-
-
-/*
- * RapidIO
- */
-#define CONFIG_SYS_SRIO1_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_SRIO1_MEM_PHYS	0xc20000000ull
-#define CONFIG_SYS_SRIO1_MEM_SIZE	0x10000000 /* 256M */
-#define CONFIG_SYS_SRIO2_MEM_VIRT	0xb0000000
-#define CONFIG_SYS_SRIO2_MEM_PHYS	0xc30000000ull
-#define CONFIG_SYS_SRIO2_MEM_SIZE	0x10000000 /* 256M */
-/*
- * for slave u-boot IMAGE instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_PHYS 0xfef080000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS1 0xfff80000ull
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_SIZE     0x80000 /* 512K */
-#define CONFIG_SRIO_PCIE_BOOT_IMAGE_MEM_BUS2 0x3fff80000ull
-/*
- * for slave UCODE and ENV instored in master memory space,
- * PHYS must be aligned based on the SIZE
- */
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_PHYS 0xfef040000ull
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_MEM_BUS 0x3ffe00000ull
-#define CONFIG_SRIO_PCIE_BOOT_UCODE_ENV_SIZE    0x40000	/* 256K */
-
-/* slave core release by master*/
-#define CONFIG_SRIO_PCIE_BOOT_BRR_OFFSET 0xe00e4
-#define CONFIG_SRIO_PCIE_BOOT_RELEASE_MASK 0x00000001 /* release core 0 */
-
-/*
- * SRIO_PCIE_BOOT - SLAVE
- */
-#ifdef CONFIG_SRIO_PCIE_BOOT_SLAVE
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR 0xFFE00000
-#define CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR_PHYS \
-		(0x300000000ull | CONFIG_SYS_SRIO_PCIE_BOOT_UCODE_ENV_ADDR)
-#endif
-
-/*
- * eSPI - Enhanced SPI
- */
-#ifdef CONFIG_SPI_FLASH
-#define CONFIG_FSL_ESPI
-#define CONFIG_SPI_FLASH_SST
-#define CONFIG_SPI_FLASH_STMICRO
-#define CONFIG_SPI_FLASH_SPANSION
-#define CONFIG_CMD_SF
-#define CONFIG_SF_DEFAULT_SPEED	 10000000
-#define CONFIG_SF_DEFAULT_MODE	  0
-#endif
-
-/*
- * General PCI
- * Memory space is mapped 1-1, but I/O space must start from 0.
- */
-#define CONFIG_PCI		/* Enable PCI/PCIE */
-#define CONFIG_PCIE1		/* PCIE controler 1 */
-#define CONFIG_PCIE2		/* PCIE controler 2 */
-#define CONFIG_PCIE3		/* PCIE controler 3 */
-#define CONFIG_PCIE4		/* PCIE controler 4 */
-#define CONFIG_FSL_PCI_INIT	/* Use common FSL init code */
-#define CONFIG_SYS_PCI_64BIT	/* enable 64-bit PCI resources */
-/* controller 1, direct to uli, tgtid 3, Base address 20000 */
-#define CONFIG_SYS_PCIE1_MEM_VIRT	0x80000000
-#define CONFIG_SYS_PCIE1_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE1_MEM_PHYS	0xc00000000ull
-#define CONFIG_SYS_PCIE1_MEM_SIZE	0x20000000      /* 512M */
-#define CONFIG_SYS_PCIE1_IO_VIRT	0xf8000000
-#define CONFIG_SYS_PCIE1_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE1_IO_PHYS	0xff8000000ull
-#define CONFIG_SYS_PCIE1_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 2, Slot 2, tgtid 2, Base address 201000 */
-#define CONFIG_SYS_PCIE2_MEM_VIRT	0xa0000000
-#define CONFIG_SYS_PCIE2_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE2_MEM_PHYS	0xc20000000ull
-#define CONFIG_SYS_PCIE2_MEM_SIZE	0x10000000 /* 256M */
-#define CONFIG_SYS_PCIE2_IO_VIRT	0xf8010000
-#define CONFIG_SYS_PCIE2_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE2_IO_PHYS	0xff8010000ull
-#define CONFIG_SYS_PCIE2_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 3, Slot 1, tgtid 1, Base address 202000 */
-#define CONFIG_SYS_PCIE3_MEM_VIRT	0xb0000000
-#define CONFIG_SYS_PCIE3_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE3_MEM_PHYS	0xc30000000ull
-#define CONFIG_SYS_PCIE3_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCIE3_IO_VIRT	0xf8020000
-#define CONFIG_SYS_PCIE3_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE3_IO_PHYS	0xff8020000ull
-#define CONFIG_SYS_PCIE3_IO_SIZE	0x00010000	/* 64k */
-
-/* controller 4, Base address 203000 */
-#define CONFIG_SYS_PCIE4_MEM_VIRT       0xc0000000
-#define CONFIG_SYS_PCIE4_MEM_BUS	0xe0000000
-#define CONFIG_SYS_PCIE4_MEM_PHYS	0xc40000000ull
-#define CONFIG_SYS_PCIE4_MEM_SIZE	0x10000000	/* 256M */
-#define CONFIG_SYS_PCIE4_IO_BUS		0x00000000
-#define CONFIG_SYS_PCIE4_IO_PHYS	0xff8030000ull
-#define CONFIG_SYS_PCIE4_IO_SIZE	0x00010000	/* 64k */
-
-#ifdef CONFIG_PCI
-#define CONFIG_PCI_INDIRECT_BRIDGE
-#define CONFIG_FSL_PCIE_RESET           /* need PCIe reset errata LSZ ADD */
-#define CONFIG_NET_MULTI
-#define CONFIG_E1000
-#define CONFIG_PCI_PNP		/* do pci plug-and-play */
-#define CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#define CONFIG_DOS_PARTITION
-#endif
-
-/* Qman/Bman */
-#ifndef CONFIG_NOBQFMAN
-#define CONFIG_SYS_DPAA_QBMAN		/* Support Q/Bman */
-#define CONFIG_SYS_BMAN_NUM_PORTALS	18
-#define CONFIG_SYS_BMAN_MEM_BASE	0xf4000000
-#define CONFIG_SYS_BMAN_MEM_PHYS	0xff4000000ull
-#define CONFIG_SYS_BMAN_MEM_SIZE	0x02000000
-#define CONFIG_SYS_QMAN_NUM_PORTALS	18
-#define CONFIG_SYS_QMAN_MEM_BASE	0xf6000000
-#define CONFIG_SYS_QMAN_MEM_PHYS	0xff6000000ull
-#define CONFIG_SYS_QMAN_MEM_SIZE	0x02000000
-
-#define CONFIG_SYS_DPAA_FMAN
-#define CONFIG_SYS_DPAA_PME
-#define CONFIG_SYS_PMAN
-#define CONFIG_SYS_DPAA_DCE
-#define CONFIG_SYS_DPAA_RMAN		/* RMan */
-#define CONFIG_SYS_INTERLAKEN
-
-/* Default address of microcode for the Linux Fman driver */
-#if defined(CONFIG_SPIFLASH)
-/*
- * env is stored at 0x100000, sector size is 0x10000, ucode is stored after
- * env, so we got 0x110000.
- */
-#define CONFIG_SYS_QE_FW_IN_SPIFLASH
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0x110000
-#elif defined(CONFIG_SDCARD)
-/*
- * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is
- * about 825KB (1650 blocks), Env is stored after the image, and the env size is
- * 0x2000 (16 blocks), 8 + 1650 + 16 = 1674, enlarge it to 1680.
- */
-#define CONFIG_SYS_QE_FMAN_FW_IN_MMC
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(512 * 1680)
-#elif defined(CONFIG_NAND)
-#define CONFIG_SYS_QE_FMAN_FW_IN_NAND
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	(8 * CONFIG_SYS_NAND_BLOCK_SIZE)
-#elif defined(CONFIG_SRIO_PCIE_BOOT_SLAVE)
-/*
- * Slave has no ucode locally, it can fetch this from remote. When implementing
- * in two corenet boards, slave's ucode could be stored in master's memory
- * space, the address can be mapped from slave TLB->slave LAW->
- * slave SRIO or PCIE outbound window->master inbound window->
- * master LAW->the ucode address in master's memory space.
- */
-#define CONFIG_SYS_QE_FMAN_FW_IN_REMOTE
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xFFE00000
-#else
-#define CONFIG_SYS_QE_FMAN_FW_IN_NOR
-#define CONFIG_SYS_QE_FMAN_FW_ADDR	0xEFF00000
-#endif
-#define CONFIG_SYS_QE_FMAN_FW_LENGTH	0x10000
-#define CONFIG_SYS_FDT_PAD		(0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH)
-#endif /* CONFIG_NOBQFMAN */
-
-#ifdef CONFIG_SYS_DPAA_FMAN
-#define CONFIG_FMAN_ENET
-#define CONFIG_PHYLIB_10G
-#define CONFIG_PHY_VITESSE
-#define CONFIG_PHY_REALTEK
-#define CONFIG_PHY_TERANETICS
-#define RGMII_PHY1_ADDR	0x1
-#define RGMII_PHY2_ADDR	0x2
-#define FM1_10GEC1_PHY_ADDR	  0x3
-#define SGMII_CARD_PORT1_PHY_ADDR 0x1C
-#define SGMII_CARD_PORT2_PHY_ADDR 0x1D
-#define SGMII_CARD_PORT3_PHY_ADDR 0x1E
-#define SGMII_CARD_PORT4_PHY_ADDR 0x1F
-#endif
-
-#ifdef CONFIG_FMAN_ENET
-#define CONFIG_MII		/* MII PHY management */
-#define CONFIG_ETHPRIME		"FM1@DTSEC3"
-#define CONFIG_PHY_GIGE		/* Include GbE speed/duplex detection */
-#endif
-
-/*
- * SATA
- */
-#ifdef CONFIG_FSL_SATA_V2
-#define CONFIG_LIBATA
-#define CONFIG_FSL_SATA
-#define CONFIG_SYS_SATA_MAX_DEVICE	2
-#define CONFIG_SATA1
-#define CONFIG_SYS_SATA1		CONFIG_SYS_MPC85xx_SATA1_ADDR
-#define CONFIG_SYS_SATA1_FLAGS		FLAGS_DMA
-#define CONFIG_SATA2
-#define CONFIG_SYS_SATA2		CONFIG_SYS_MPC85xx_SATA2_ADDR
-#define CONFIG_SYS_SATA2_FLAGS		FLAGS_DMA
-#define CONFIG_LBA48
-#define CONFIG_CMD_SATA
-#define CONFIG_DOS_PARTITION
-#define CONFIG_CMD_EXT2
-#endif
-
-/*
- * USB
- */
-#ifdef CONFIG_USB_EHCI
-#define CONFIG_CMD_USB
-#define CONFIG_USB_STORAGE
-#define CONFIG_USB_EHCI_FSL
-#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
-#define CONFIG_CMD_EXT2
-#define CONFIG_HAS_FSL_DR_USB
-#endif
-
-/*
- * SDHC
- */
-#ifdef CONFIG_MMC
-#define CONFIG_CMD_MMC
-#define CONFIG_FSL_ESDHC
-#define CONFIG_SYS_FSL_ESDHC_ADDR	CONFIG_SYS_MPC85xx_ESDHC_ADDR
-#define CONFIG_SYS_FSL_ESDHC_BROKEN_TIMEOUT
-#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
-#define CONFIG_GENERIC_MMC
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-#define CONFIG_DOS_PARTITION
-#endif
-
-/*
- * Environment
- */
-#define CONFIG_LOADS_ECHO	/* echo on for serial download */
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	/* allow baudrate change */
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_ERRATA
-#define CONFIG_CMD_GREPENV
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_SETEXPR
-#define CONFIG_CMD_REGINFO
-#define CONFIG_CMD_BDI
-
-#ifdef CONFIG_PCI
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_NET
-#endif
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP		/* undef to save memory */
-#define CONFIG_CMDLINE_EDITING		/* Command-line editing */
-#define CONFIG_AUTO_COMPLETE		/* add autocompletion support */
-#define CONFIG_SYS_LOAD_ADDR	0x2000000 /* default load address */
-#define CONFIG_SYS_PROMPT	"=> "	  /* Monitor Command Prompt */
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_SYS_CBSIZE	1024	  /* Console I/O Buffer Size */
-#else
-#define CONFIG_SYS_CBSIZE	256	  /* Console I/O Buffer Size */
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
-#define CONFIG_SYS_MAXARGS	16	/* max number of command args */
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */
-#define CONFIG_SYS_HZ		1000	/* decrementer freq: 1ms ticks*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 64 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ	(64 << 20)	/* Initial map for Linux*/
-#define CONFIG_SYS_BOOTM_LEN	(64 << 20)	/* Increase max gunzip size */
-
-#ifdef CONFIG_CMD_KGDB
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
-#endif
-
-/*
- * Environment Configuration
- */
-#define CONFIG_ROOTPATH	 "/opt/nfsroot"
-#define CONFIG_BOOTFILE	 "uImage"
-#define CONFIG_UBOOTPATH "u-boot.bin"	/* U-Boot image on TFTP server */
-
-/* default location for tftp and bootm */
-#define CONFIG_LOADADDR		1000000
-#define CONFIG_BAUDRATE		115200
-#define CONFIG_BOOTDELAY	10	/* -1 disables auto-boot */
-#define __USB_PHY_TYPE		utmi
-
-#define	CONFIG_EXTRA_ENV_SETTINGS				\
-	"hwconfig=fsl_ddr:"					\
-	"ctlr_intlv=" __stringify(CTRL_INTLV_PREFERED) ","	\
-	"bank_intlv=auto;"					\
-	"usb1:dr_mode=host,phy_type=" __stringify(__USB_PHY_TYPE) "\0"\
-	"netdev=eth0\0"						\
-	"uboot=" __stringify(CONFIG_UBOOTPATH) "\0"		\
-	"ubootaddr=" __stringify(CONFIG_SYS_TEXT_BASE) "\0"	\
-	"tftpflash=tftpboot $loadaddr $uboot && "		\
-	"protect off $ubootaddr +$filesize && "			\
-	"erase $ubootaddr +$filesize && "			\
-	"cp.b $loadaddr $ubootaddr $filesize && "		\
-	"protect on $ubootaddr +$filesize && "			\
-	"cmp.b $loadaddr $ubootaddr $filesize\0"		\
-	"consoledev=ttyS0\0"					\
-	"ramdiskaddr=2000000\0"					\
-	"ramdiskfile=t2080qds/ramdisk.uboot\0"			\
-	"fdtaddr=c00000\0"					\
-	"fdtfile=t2080qds/t2080qds.dtb\0"			\
-	"bdev=sda3\0"						\
-	"c=ffe\0"
-
-/*
- * For emulation this causes u-boot to jump to the start of the
- * proof point app code automatically
- */
-#define CONFIG_PROOF_POINTS				\
-	"setenv bootargs root=/dev/$bdev rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"cpu 1 release 0x29000000 - - -;"		\
-	"cpu 2 release 0x29000000 - - -;"		\
-	"cpu 3 release 0x29000000 - - -;"		\
-	"cpu 4 release 0x29000000 - - -;"		\
-	"cpu 5 release 0x29000000 - - -;"		\
-	"cpu 6 release 0x29000000 - - -;"		\
-	"cpu 7 release 0x29000000 - - -;"		\
-	"go 0x29000000"
-
-#define CONFIG_HVBOOT				\
-	"setenv bootargs config-addr=0x60000000; "	\
-	"bootm 0x01000000 - 0x00f00000"
-
-#define CONFIG_ALU				\
-	"setenv bootargs root=/dev/$bdev rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"cpu 1 release 0x01000000 - - -;"		\
-	"cpu 2 release 0x01000000 - - -;"		\
-	"cpu 3 release 0x01000000 - - -;"		\
-	"cpu 4 release 0x01000000 - - -;"		\
-	"cpu 5 release 0x01000000 - - -;"		\
-	"cpu 6 release 0x01000000 - - -;"		\
-	"cpu 7 release 0x01000000 - - -;"		\
-	"go 0x01000000"
-
-#define CONFIG_LINUX				\
-	"setenv bootargs root=/dev/ram rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"setenv ramdiskaddr 0x02000000;"		\
-	"setenv fdtaddr 0x00c00000;"			\
-	"setenv loadaddr 0x1000000;"			\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_HDBOOT					\
-	"setenv bootargs root=/dev/$bdev rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_NFSBOOTCOMMAND			\
-	"setenv bootargs root=/dev/nfs rw "	\
-	"nfsroot=$serverip:$rootpath "		\
-	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $loadaddr $bootfile;"		\
-	"tftp $fdtaddr $fdtfile;"		\
-	"bootm $loadaddr - $fdtaddr"
-
-#define CONFIG_RAMBOOTCOMMAND				\
-	"setenv bootargs root=/dev/ram rw "		\
-	"console=$consoledev,$baudrate $othbootargs;"	\
-	"tftp $ramdiskaddr $ramdiskfile;"		\
-	"tftp $loadaddr $bootfile;"			\
-	"tftp $fdtaddr $fdtfile;"			\
-	"bootm $loadaddr $ramdiskaddr $fdtaddr"
-
-#define CONFIG_BOOTCOMMAND		CONFIG_LINUX
-
-#ifdef CONFIG_SECURE_BOOT
-#include <asm/fsl_secure_boot.h>
-#undef CONFIG_CMD_USB
-#endif
-
-#endif	/* __T2080QDS_H */