* Add start-up delay to make sure power has stabilized before

  attempting to switch on USB on SX1 board.

* Patch by Josef Wagner, 18 Mar 2004:
  - Add support for MicroSys XM250 board (PXA255)
  - Add support for MicroSys PM828 board (MPC8280)
  - Add support for 32 MB Flash on PM825/826
  - new SDRAM refresh rate for PM825/PM826
  - added support for MicroSys PM520 (MPC5200)
  - replaced Query by Identify command in CPU86/flash.c
    to support 28F160F3B

* Fix wrap around problem with udelay() on ARM920T

* Add support for Macronix flash on TRAB board

1 files changed, 565 insertions, 0 deletions

diff --git a/include/configs/PM828.h b/include/configs/PM828.h
new file mode 100644
index 0000000..d6a926d
--- /dev/null
+++ b/include/configs/PM828.h
@@ -0,0 +1,565 @@
+/*
+ * (C) Copyright 2001-2004
+ * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * board/config.h - configuration options, board specific
+ */
+
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+#undef CFG_RAMBOOT
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+
+#define CONFIG_MPC8260		1	/* This is a MPC8260 CPU	*/
+#define CONFIG_PM828		1	/* ...on a PM828 module */
+
+#undef CONFIG_DB_CR826_J30x_ON		/* J30x jumpers on D.B. carrier */
+
+#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+
+#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
+
+#define CONFIG_PREBOOT	"echo;echo Type \"run flash_nfs\" to mount root filesystem over NFS;echo"
+
+#undef	CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND							\
+	"bootp;"								\
+	"setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) "	\
+	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;"	\
+	"bootm"
+
+/* enable I2C and select the hardware/software driver */
+#undef	CONFIG_HARD_I2C
+#define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
+# define CFG_I2C_SPEED		50000
+# define CFG_I2C_SLAVE		0xFE
+/*
+ * Software (bit-bang) I2C driver configuration
+ */
+#define I2C_PORT	3		/* Port A=0, B=1, C=2, D=3 */
+#define I2C_ACTIVE	(iop->pdir |=  0x00010000)
+#define I2C_TRISTATE	(iop->pdir &= ~0x00010000)
+#define I2C_READ	((iop->pdat & 0x00010000) != 0)
+#define I2C_SDA(bit)	if(bit) iop->pdat |=  0x00010000; \
+			else	iop->pdat &= ~0x00010000
+#define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00020000; \
+			else	iop->pdat &= ~0x00020000
+#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
+
+
+#define CONFIG_RTC_PCF8563
+#define CFG_I2C_RTC_ADDR	0x51
+
+/*
+ * select serial console configuration
+ *
+ * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
+ * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
+ * for SCC).
+ *
+ * if CONFIG_CONS_NONE is defined, then the serial console routines must
+ * defined elsewhere (for example, on the cogent platform, there are serial
+ * ports on the motherboard which are used for the serial console - see
+ * cogent/cma101/serial.[ch]).
+ */
+#define CONFIG_CONS_ON_SMC		/* define if console on SMC */
+#undef	CONFIG_CONS_ON_SCC		/* define if console on SCC */
+#undef	CONFIG_CONS_NONE		/* define if console on something else*/
+#define CONFIG_CONS_INDEX	2	/* which serial channel for console */
+
+/*
+ * select ethernet configuration
+ *
+ * if CONFIG_ETHER_ON_SCC is selected, then
+ *   - CONFIG_ETHER_INDEX must be set to the channel number (1-4)
+ *   - CONFIG_NET_MULTI must not be defined
+ *
+ * if CONFIG_ETHER_ON_FCC is selected, then
+ *   - one or more CONFIG_ETHER_ON_FCCx (x=1,2,3) must also be selected
+ *   - CONFIG_NET_MULTI must be defined
+ *
+ * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
+ * defined elsewhere (as for the console), or CFG_CMD_NET must be removed
+ * from CONFIG_COMMANDS to remove support for networking.
+ */
+#define CONFIG_NET_MULTI
+#undef	CONFIG_ETHER_NONE		/* define if ether on something else */
+
+#undef	CONFIG_ETHER_ON_SCC		/* define if ether on SCC	*/
+#define CONFIG_ETHER_INDEX    1		/* which SCC channel for ethernet */
+
+#define CONFIG_ETHER_ON_FCC		/* define if ether on FCC	*/
+/*
+ * - Rx-CLK is CLK11
+ * - Tx-CLK is CLK10
+ */
+#define CONFIG_ETHER_ON_FCC1
+# define CFG_CMXFCR_MASK1	(CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
+#ifndef CONFIG_DB_CR826_J30x_ON
+# define CFG_CMXFCR_VALUE1	(CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK10)
+#else
+# define CFG_CMXFCR_VALUE1	(CMXFCR_RF1CS_CLK11|CMXFCR_TF1CS_CLK12)
+#endif
+/*
+ * - Rx-CLK is CLK15
+ * - Tx-CLK is CLK14
+ */
+#define CONFIG_ETHER_ON_FCC2
+# define CFG_CMXFCR_MASK2	(CMXFCR_FC2|CMXFCR_RF2CS_MSK|CMXFCR_TF2CS_MSK)
+# define CFG_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13|CMXFCR_TF2CS_CLK14)
+/*
+ * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
+ * - Enable Full Duplex in FSMR
+ */
+# define CFG_CPMFCR_RAMTYPE	0
+# define CFG_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
+
+/* system clock rate (CLKIN) - equal to the 60x and local bus speed */
+#define CONFIG_8260_CLKIN	100000000	/* in Hz */
+
+#if defined(CONFIG_CONS_NONE) || defined(CONFIG_CONS_USE_EXTC)
+#define CONFIG_BAUDRATE		230400
+#else
+#define CONFIG_BAUDRATE		9600
+#endif
+
+#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
+#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
+
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT|CONFIG_BOOTP_BOOTFILESIZE)
+
+#ifdef CONFIG_PCI
+#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | \
+				 CFG_CMD_BEDBUG | \
+				 CFG_CMD_DATE	| \
+				 CFG_CMD_DOC	| \
+				 CFG_CMD_EEPROM | \
+				 CFG_CMD_I2C	| \
+				 CFG_CMD_PCI)
+#else	/* ! PCI */
+#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | \
+				 CFG_CMD_BEDBUG | \
+				 CFG_CMD_DATE	| \
+				 CFG_CMD_DOC	| \
+				 CFG_CMD_EEPROM | \
+				 CFG_CMD_I2C	)
+#endif	/* CONFIG_PCI */
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+/*
+ * Disk-On-Chip configuration
+ */
+
+#define CFG_DOC_SHORT_TIMEOUT
+#define CFG_MAX_DOC_DEVICE	1	/* Max number of DOC devices	*/
+
+#define CFG_DOC_SUPPORT_2000
+#define CFG_DOC_SUPPORT_MILLENNIUM
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CFG_LONGHELP			/* undef to save memory		*/
+#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#else
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS	16		/* max number of command args	*/
+#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+
+#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CFG_MEMTEST_END 0x0C00000	/* 4 ... 12 MB in DRAM	*/
+
+#define CFG_LOAD_ADDR	0x100000	/* default load address */
+
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+
+#define CFG_RESET_ADDRESS 0xFDFFFFFC	/* "bad" address		*/
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ	     (8 << 20)	     /* Initial Memory map for Linux */
+
+/*-----------------------------------------------------------------------
+ * Flash and Boot ROM mapping
+ */
+
+#define CFG_BOOTROM_BASE	0xFF800000
+#define CFG_BOOTROM_SIZE	0x00080000
+#define CFG_FLASH0_BASE		0x40000000
+#define CFG_FLASH0_SIZE		0x02000000
+#define CFG_DOC_BASE		0xFF800000
+#define CFG_DOC_SIZE		0x00100000
+
+
+/* Flash bank size (for preliminary settings)
+ */
+#define CFG_FLASH_SIZE CFG_FLASH0_SIZE
+
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS	1	/* max num of memory banks	*/
+#define CFG_MAX_FLASH_SECT	135	/* max num of sects on one chip */
+
+#define CFG_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)	*/
+#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)	*/
+
+#if 0
+/* Start port with environment in flash; switch to EEPROM later */
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_ADDR		(CFG_FLASH_BASE+0x40000)
+#define CFG_ENV_SIZE		0x40000
+#define CFG_ENV_SECT_SIZE	0x40000
+#else
+/* Final version: environment in EEPROM */
+#define CFG_ENV_IS_IN_EEPROM	1
+#define CFG_I2C_EEPROM_ADDR	0x58
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_BITS	4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
+#define CFG_ENV_OFFSET		512
+#define CFG_ENV_SIZE		(2048 - 512)
+#endif
+
+/*-----------------------------------------------------------------------
+ * Hard Reset Configuration Words
+ *
+ * if you change bits in the HRCW, you must also change the CFG_*
+ * defines for the various registers affected by the HRCW e.g. changing
+ * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ */
+#if defined(CONFIG_BOOT_ROM)
+#define CFG_HRCW_MASTER		(HRCW_BPS01 | HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
+#else
+#define CFG_HRCW_MASTER		(HRCW_CIP | HRCW_ISB100 | HRCW_BMS)
+#endif
+
+/* no slaves so just fill with zeros */
+#define CFG_HRCW_SLAVE1		0
+#define CFG_HRCW_SLAVE2		0
+#define CFG_HRCW_SLAVE3		0
+#define CFG_HRCW_SLAVE4		0
+#define CFG_HRCW_SLAVE5		0
+#define CFG_HRCW_SLAVE6		0
+#define CFG_HRCW_SLAVE7		0
+
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR		0xF0000000
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR	CFG_IMMR
+#define CFG_INIT_RAM_END	0x4000	/* End of used area in DPRAM	*/
+#define CFG_GBL_DATA_SIZE	128 /* size in bytes reserved for initial data*/
+#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ *
+ * 60x SDRAM is mapped at CFG_SDRAM_BASE, local SDRAM
+ * is mapped at SDRAM_BASE2_PRELIM.
+ */
+#define CFG_SDRAM_BASE		0x00000000
+#define CFG_FLASH_BASE		CFG_FLASH0_BASE
+#define CFG_MONITOR_BASE	TEXT_BASE
+#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()*/
+
+#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
+# define CFG_RAMBOOT
+#endif
+
+#ifdef	CONFIG_PCI
+#define CONFIG_PCI_PNP
+#define CONFIG_EEPRO100
+#define CFG_RX_ETH_BUFFER	8		/* use 8 rx buffer on eepro100	*/
+#endif
+
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD		0x01	/* Normal Power-On: Boot from FLASH*/
+#define BOOTFLAG_WARM		0x02	/* Software reboot		   */
+
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE	32	/* For MPC8260 CPU		*/
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * HIDx - Hardware Implementation-dependent Registers			 2-11
+ *-----------------------------------------------------------------------
+ * HID0 also contains cache control - initially enable both caches and
+ * invalidate contents, then the final state leaves only the instruction
+ * cache enabled. Note that Power-On and Hard reset invalidate the caches,
+ * but Soft reset does not.
+ *
+ * HID1 has only read-only information - nothing to set.
+ */
+#define CFG_HID0_INIT	(HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI|\
+				HID0_IFEM|HID0_ABE)
+#define CFG_HID0_FINAL	(HID0_ICE|HID0_IFEM|HID0_ABE)
+#define CFG_HID2	0
+
+/*-----------------------------------------------------------------------
+ * RMR - Reset Mode Register					 5-5
+ *-----------------------------------------------------------------------
+ * turn on Checkstop Reset Enable
+ */
+#define CFG_RMR		RMR_CSRE
+
+/*-----------------------------------------------------------------------
+ * BCR - Bus Configuration					 4-25
+ *-----------------------------------------------------------------------
+ */
+
+#define BCR_APD01	0x10000000
+#define CFG_BCR		(BCR_APD01|BCR_ETM|BCR_LETM)	/* 8260 mode */
+
+/*-----------------------------------------------------------------------
+ * SIUMCR - SIU Module Configuration				 4-31
+ *-----------------------------------------------------------------------
+ */
+#if 0
+#define CFG_SIUMCR	(SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_CS10PC01)
+#else
+#define CFG_SIUMCR	(SIUMCR_DPPC10|SIUMCR_APPC10)
+#endif
+
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control				 4-35
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR	(SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+			 SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
+#else
+#define CFG_SYPCR	(SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+			 SYPCR_SWRI|SYPCR_SWP)
+#endif /* CONFIG_WATCHDOG */
+
+/*-----------------------------------------------------------------------
+ * TMCNTSC - Time Counter Status and Control			 4-40
+ *-----------------------------------------------------------------------
+ * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
+ * and enable Time Counter
+ */
+#define CFG_TMCNTSC	(TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control		 4-42
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
+ * Periodic timer
+ */
+#define CFG_PISCR	(PISCR_PS|PISCR_PTF|PISCR_PTE)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock Control					 9-8
+ *-----------------------------------------------------------------------
+ */
+#define CFG_SCCR	(SCCR_DFBRG00)
+
+/*-----------------------------------------------------------------------
+ * RCCR - RISC Controller Configuration				13-7
+ *-----------------------------------------------------------------------
+ */
+#define CFG_RCCR	0
+
+/*
+ * Init Memory Controller:
+ *
+ * Bank Bus	Machine PortSz	Device
+ * ---- ---	------- ------	------
+ *  0	60x	GPCM	64 bit	FLASH
+ *  1	60x	SDRAM	64 bit	SDRAM
+ *
+ */
+
+	/* Initialize SDRAM on local bus
+	 */
+#define CFG_INIT_LOCAL_SDRAM
+
+
+/* Minimum mask to separate preliminary
+ * address ranges for CS[0:2]
+ */
+#define CFG_MIN_AM_MASK 0xC0000000
+
+/*
+ * we use the same values for 32 MB and 128 MB SDRAM
+ * refresh rate = 7.68 uS (100 MHz Bus Clock)
+ */
+#define CFG_MPTPR	0x2000
+#define CFG_PSRT	0x16
+
+#define CFG_MRS_OFFS	0x00000000
+
+
+#if defined(CONFIG_BOOT_ROM)
+/*
+ * Bank 0 - Boot ROM (8 bit wide)
+ */
+#define CFG_BR0_PRELIM	((CFG_BOOTROM_BASE & BRx_BA_MSK)|\
+			 BRx_PS_8			|\
+			 BRx_MS_GPCM_P			|\
+			 BRx_V)
+
+#define CFG_OR0_PRELIM	(P2SZ_TO_AM(CFG_BOOTROM_SIZE)	|\
+			 ORxG_CSNT			|\
+			 ORxG_ACS_DIV1			|\
+			 ORxG_SCY_5_CLK			|\
+			 ORxG_EHTR			|\
+			 ORxG_TRLX)
+
+/*
+ * Bank 1 - Flash (64 bit wide)
+ */
+#define CFG_BR1_PRELIM	((CFG_FLASH_BASE & BRx_BA_MSK)	|\
+			 BRx_PS_64			|\
+			 BRx_MS_GPCM_P			|\
+			 BRx_V)
+
+#define CFG_OR1_PRELIM	(P2SZ_TO_AM(CFG_FLASH_SIZE)	|\
+			 ORxG_CSNT			|\
+			 ORxG_ACS_DIV1			|\
+			 ORxG_SCY_5_CLK			|\
+			 ORxG_EHTR			|\
+			 ORxG_TRLX)
+
+#else	/* ! CONFIG_BOOT_ROM */
+
+/*
+ * Bank 0 - Flash (64 bit wide)
+ */
+#define CFG_BR0_PRELIM	((CFG_FLASH_BASE & BRx_BA_MSK)	|\
+			 BRx_PS_64			|\
+			 BRx_MS_GPCM_P			|\
+			 BRx_V)
+
+#define CFG_OR0_PRELIM	(P2SZ_TO_AM(CFG_FLASH_SIZE)	|\
+			 ORxG_CSNT			|\
+			 ORxG_ACS_DIV1			|\
+			 ORxG_SCY_5_CLK			|\
+			 ORxG_EHTR			|\
+			 ORxG_TRLX)
+
+/*
+ * Bank 1 - Disk-On-Chip
+ */
+#define CFG_BR1_PRELIM	((CFG_DOC_BASE & BRx_BA_MSK)	|\
+			 BRx_PS_8			|\
+			 BRx_MS_GPCM_P			|\
+			 BRx_V)
+
+#define CFG_OR1_PRELIM	(P2SZ_TO_AM(CFG_DOC_SIZE)	|\
+			 ORxG_CSNT			|\
+			 ORxG_ACS_DIV1			|\
+			 ORxG_SCY_5_CLK			|\
+			 ORxG_EHTR			|\
+			 ORxG_TRLX)
+
+#endif /* CONFIG_BOOT_ROM */
+
+/* Bank 2 - SDRAM
+ */
+
+#ifndef CFG_RAMBOOT
+#define CFG_BR2_PRELIM	((CFG_SDRAM_BASE & BRx_BA_MSK)	|\
+			 BRx_PS_64			|\
+			 BRx_MS_SDRAM_P			|\
+			 BRx_V)
+
+	/* SDRAM initialization values for 8-column chips
+	 */
+#define CFG_OR2_8COL	(CFG_MIN_AM_MASK		|\
+			 ORxS_BPD_4			|\
+			 ORxS_ROWST_PBI0_A9		|\
+			 ORxS_NUMR_12)
+
+#define CFG_PSDMR_8COL	(PSDMR_SDAM_A13_IS_A5		|\
+			 PSDMR_BSMA_A14_A16		|\
+			 PSDMR_SDA10_PBI0_A10		|\
+			 PSDMR_RFRC_7_CLK		|\
+			 PSDMR_PRETOACT_2W		|\
+			 PSDMR_ACTTORW_2W		|\
+			 PSDMR_LDOTOPRE_1C		|\
+			 PSDMR_WRC_1C			|\
+			 PSDMR_CL_2)
+
+	/* SDRAM initialization values for 9-column chips
+	 */
+#define CFG_OR2_9COL	(CFG_MIN_AM_MASK		|\
+			 ORxS_BPD_4			|\
+			 ORxS_ROWST_PBI0_A7		|\
+			 ORxS_NUMR_13)
+
+#define CFG_PSDMR_9COL	(PSDMR_SDAM_A14_IS_A5		|\
+			 PSDMR_BSMA_A13_A15		|\
+			 PSDMR_SDA10_PBI0_A9		|\
+			 PSDMR_RFRC_7_CLK		|\
+			 PSDMR_PRETOACT_2W		|\
+			 PSDMR_ACTTORW_2W		|\
+			 PSDMR_LDOTOPRE_1C		|\
+			 PSDMR_WRC_1C			|\
+			 PSDMR_CL_2)
+
+#define CFG_OR2_PRELIM	 CFG_OR2_9COL
+#define CFG_PSDMR	 CFG_PSDMR_9COL
+
+#endif /* CFG_RAMBOOT */
+
+#endif	/* __CONFIG_H */