Merge branch 'fixes' into cleanups

Conflicts:

	board/atmel/atngw100/atngw100.c
	board/atmel/atstk1000/atstk1000.c
	cpu/at32ap/at32ap700x/gpio.c
	include/asm-avr32/arch-at32ap700x/clk.h
	include/configs/atngw100.h
	include/configs/atstk1002.h
	include/configs/atstk1003.h
	include/configs/atstk1004.h
	include/configs/atstk1006.h
	include/configs/favr-32-ezkit.h
	include/configs/hammerhead.h
	include/configs/mimc200.h

1 files changed, 254 insertions, 254 deletions

diff --git a/include/configs/MPC8349EMDS.h b/include/configs/MPC8349EMDS.h
index c8870b5..8e82aac 100644
--- a/include/configs/MPC8349EMDS.h
+++ b/include/configs/MPC8349EMDS.h
@@ -65,11 +65,11 @@
 
 #define CONFIG_BOARD_EARLY_INIT_F		/* call board_pre_init */
 
-#define CFG_IMMR		0xE0000000
+#define CONFIG_SYS_IMMR		0xE0000000
 
-#undef CFG_DRAM_TEST				/* memory test, takes time */
-#define CFG_MEMTEST_START	0x00000000      /* memtest region */
-#define CFG_MEMTEST_END		0x00100000
+#undef CONFIG_SYS_DRAM_TEST				/* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START	0x00000000      /* memtest region */
+#define CONFIG_SYS_MEMTEST_END		0x00100000
 
 /*
  * DDR Setup
@@ -90,17 +90,17 @@
  */
 #undef CONFIG_DDR_32BIT
 
-#define CFG_DDR_BASE		0x00000000	/* DDR is system memory*/
-#define CFG_SDRAM_BASE		CFG_DDR_BASE
-#define CFG_DDR_SDRAM_BASE	CFG_DDR_BASE
-#define CFG_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
+#define CONFIG_SYS_DDR_BASE		0x00000000	/* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
 				DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
 #undef  CONFIG_DDR_2T_TIMING
 
 /*
  * DDRCDR - DDR Control Driver Register
  */
-#define CFG_DDRCDR_VALUE	0x80080001
+#define CONFIG_SYS_DDRCDR_VALUE	0x80080001
 
 #if defined(CONFIG_SPD_EEPROM)
 /*
@@ -111,34 +111,34 @@
 /*
  * Manually set up DDR parameters
  */
-#define CFG_DDR_SIZE		256		/* MB */
+#define CONFIG_SYS_DDR_SIZE		256		/* MB */
 #if defined(CONFIG_DDR_II)
-#define CFG_DDRCDR		0x80080001
-#define CFG_DDR_CS2_BNDS	0x0000000f
-#define CFG_DDR_CS2_CONFIG	0x80330102
-#define CFG_DDR_TIMING_0	0x00220802
-#define CFG_DDR_TIMING_1	0x38357322
-#define CFG_DDR_TIMING_2	0x2f9048c8
-#define CFG_DDR_TIMING_3	0x00000000
-#define CFG_DDR_CLK_CNTL	0x02000000
-#define CFG_DDR_MODE		0x47d00432
-#define CFG_DDR_MODE2		0x8000c000
-#define CFG_DDR_INTERVAL	0x03cf0080
-#define CFG_DDR_SDRAM_CFG	0x43000000
-#define CFG_DDR_SDRAM_CFG2	0x00401000
+#define CONFIG_SYS_DDRCDR		0x80080001
+#define CONFIG_SYS_DDR_CS2_BNDS	0x0000000f
+#define CONFIG_SYS_DDR_CS2_CONFIG	0x80330102
+#define CONFIG_SYS_DDR_TIMING_0	0x00220802
+#define CONFIG_SYS_DDR_TIMING_1	0x38357322
+#define CONFIG_SYS_DDR_TIMING_2	0x2f9048c8
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+#define CONFIG_SYS_DDR_CLK_CNTL	0x02000000
+#define CONFIG_SYS_DDR_MODE		0x47d00432
+#define CONFIG_SYS_DDR_MODE2		0x8000c000
+#define CONFIG_SYS_DDR_INTERVAL	0x03cf0080
+#define CONFIG_SYS_DDR_SDRAM_CFG	0x43000000
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
 #else
-#define CFG_DDR_CONFIG		(CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
-#define CFG_DDR_TIMING_1	0x36332321
-#define CFG_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
-#define CFG_DDR_CONTROL		0xc2000000	/* unbuffered,no DYN_PWR */
-#define CFG_DDR_INTERVAL	0x04060100	/* autocharge,no open page */
+#define CONFIG_SYS_DDR_CONFIG		(CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_10)
+#define CONFIG_SYS_DDR_TIMING_1	0x36332321
+#define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
+#define CONFIG_SYS_DDR_CONTROL		0xc2000000	/* unbuffered,no DYN_PWR */
+#define CONFIG_SYS_DDR_INTERVAL	0x04060100	/* autocharge,no open page */
 
 #if defined(CONFIG_DDR_32BIT)
 /* set burst length to 8 for 32-bit data path */
-#define CFG_DDR_MODE		0x00000023	/* DLL,normal,seq,4/2.5, 8 burst len */
+#define CONFIG_SYS_DDR_MODE		0x00000023	/* DLL,normal,seq,4/2.5, 8 burst len */
 #else
 /* the default burst length is 4 - for 64-bit data path */
-#define CFG_DDR_MODE		0x00000022	/* DLL,normal,seq,4/2.5, 4 burst len */
+#define CONFIG_SYS_DDR_MODE		0x00000022	/* DLL,normal,seq,4/2.5, 4 burst len */
 #endif
 #endif
 #endif
@@ -146,63 +146,63 @@
 /*
  * SDRAM on the Local Bus
  */
-#define CFG_LBC_SDRAM_BASE	0xF0000000	/* Localbus SDRAM */
-#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+#define CONFIG_SYS_LBC_SDRAM_BASE	0xF0000000	/* Localbus SDRAM */
+#define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
 
 /*
  * FLASH on the Local Bus
  */
-#define CFG_FLASH_CFI				/* use the Common Flash Interface */
+#define CONFIG_SYS_FLASH_CFI				/* use the Common Flash Interface */
 #define CONFIG_FLASH_CFI_DRIVER			/* use the CFI driver */
-#define CFG_FLASH_BASE		0xFE000000	/* start of FLASH   */
-#define CFG_FLASH_SIZE		32		/* max flash size in MB */
-/* #define CFG_FLASH_USE_BUFFER_WRITE */
+#define CONFIG_SYS_FLASH_BASE		0xFE000000	/* start of FLASH   */
+#define CONFIG_SYS_FLASH_SIZE		32		/* max flash size in MB */
+#define CONFIG_SYS_FLASH_PROTECTION	1		/* Use h/w Flash protection. */
+/* #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE */
 
-#define CFG_BR0_PRELIM		(CFG_FLASH_BASE |	/* flash Base address */ \
+#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE |	/* flash Base address */ \
 				(2 << BR_PS_SHIFT) |	/* 16 bit port size */	 \
 				BR_V)			/* valid */
-#define CFG_OR0_PRELIM		((~(CFG_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
+#define CONFIG_SYS_OR0_PRELIM		((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
 				OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | OR_GPCM_XACS | OR_GPCM_SCY_15 | \
 				OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
-#define CFG_LBLAWBAR0_PRELIM	CFG_FLASH_BASE	/* window base at flash base */
-#define CFG_LBLAWAR0_PRELIM	0x80000018	/* 32 MB window size */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE	/* window base at flash base */
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000018	/* 32 MB window size */
 
-#define CFG_MAX_FLASH_BANKS	1		/* number of banks */
-#define CFG_MAX_FLASH_SECT	256		/* max sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	256		/* max sectors per device */
 
-#undef CFG_FLASH_CHECKSUM
-#define CFG_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
-#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
+#undef CONFIG_SYS_FLASH_CHECKSUM
+#define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */
 
-#define CFG_MID_FLASH_JUMP	0x7F000000
-#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_MID_FLASH_JUMP	0x7F000000
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
 
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
 #else
-#undef  CFG_RAMBOOT
+#undef  CONFIG_SYS_RAMBOOT
 #endif
 
 /*
  * BCSR register on local bus 32KB, 8-bit wide for MDS config reg
  */
-#define CFG_BCSR		0xE2400000
-#define CFG_LBLAWBAR1_PRELIM	CFG_BCSR		/* Access window base at BCSR base */
-#define CFG_LBLAWAR1_PRELIM	0x8000000E		/* Access window size 32K */
-#define CFG_BR1_PRELIM		(CFG_BCSR|0x00000801)	/* Port-size=8bit, MSEL=GPCM */
-#define CFG_OR1_PRELIM		0xFFFFE8F0		/* length 32K */
+#define CONFIG_SYS_BCSR		0xE2400000
+#define CONFIG_SYS_LBLAWBAR1_PRELIM	CONFIG_SYS_BCSR		/* Access window base at BCSR base */
+#define CONFIG_SYS_LBLAWAR1_PRELIM	0x8000000E		/* Access window size 32K */
+#define CONFIG_SYS_BR1_PRELIM		(CONFIG_SYS_BCSR|0x00000801)	/* Port-size=8bit, MSEL=GPCM */
+#define CONFIG_SYS_OR1_PRELIM		0xFFFFE8F0		/* length 32K */
 
-#define CONFIG_L1_INIT_RAM
-#define CFG_INIT_RAM_LOCK	1
-#define CFG_INIT_RAM_ADDR	0xFD000000		/* Initial RAM address */
-#define CFG_INIT_RAM_END	0x1000			/* End of used area in RAM*/
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000		/* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END	0x1000			/* End of used area in RAM*/
 
-#define CFG_GBL_DATA_SIZE	0x100			/* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100			/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
-#define CFG_MONITOR_LEN		(256 * 1024)		/* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN		(128 * 1024)		/* Reserved for malloc */
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)		/* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)		/* Reserved for malloc */
 
 /*
  * Local Bus LCRR and LBCR regs
@@ -210,20 +210,20 @@
  * External Local Bus rate is
  *    CLKIN * HRCWL_CSB_TO_CLKIN / HRCWL_LCL_BUS_TO_SCB_CLK / LCRR_CLKDIV
  */
-#define CFG_LCRR	(LCRR_DBYP | LCRR_CLKDIV_4)
-#define CFG_LBC_LBCR	0x00000000
+#define CONFIG_SYS_LCRR	(LCRR_DBYP | LCRR_CLKDIV_4)
+#define CONFIG_SYS_LBC_LBCR	0x00000000
 
 /*
  * The MPC834xEA MDS for 834xE rev3.1 may not be assembled SDRAM memory.
- * if board has SRDAM on local bus, you can define CFG_LB_SDRAM
+ * if board has SRDAM on local bus, you can define CONFIG_SYS_LB_SDRAM
  */
-#undef CFG_LB_SDRAM
+#undef CONFIG_SYS_LB_SDRAM
 
-#ifdef CFG_LB_SDRAM
+#ifdef CONFIG_SYS_LB_SDRAM
 /* Local bus BR2, OR2 definition for SDRAM if soldered on the MDS board */
 /*
  * Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
  *
  * For BR2, need:
  *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
@@ -235,16 +235,16 @@
  * 0    4    8    12   16   20   24   28
  * 1111 0000 0000 0000 0001 1000 0110 0001 = F0001861
  *
- * FIXME: CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * FIXME: CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
  * FIXME: the top 17 bits of BR2.
  */
 
-#define CFG_BR2_PRELIM		0xF0001861 /* Port-size=32bit, MSEL=SDRAM */
-#define CFG_LBLAWBAR2_PRELIM	0xF0000000
-#define CFG_LBLAWAR2_PRELIM	0x80000019 /* 64M */
+#define CONFIG_SYS_BR2_PRELIM		0xF0001861 /* Port-size=32bit, MSEL=SDRAM */
+#define CONFIG_SYS_LBLAWBAR2_PRELIM	0xF0000000
+#define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000019 /* 64M */
 
 /*
- * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
  *
  * For OR2, need:
  *    64MB mask for AM, OR2[0:7] = 1111 1100
@@ -257,65 +257,65 @@
  * 1111 1100 0000 0000 0110 1001 0000 0001 = FC006901
  */
 
-#define CFG_OR2_PRELIM	0xFC006901
+#define CONFIG_SYS_OR2_PRELIM	0xFC006901
 
-#define CFG_LBC_LSRT	0x32000000    /* LB sdram refresh timer, about 6us */
-#define CFG_LBC_MRTPR	0x20000000    /* LB refresh timer prescal, 266MHz/32 */
+#define CONFIG_SYS_LBC_LSRT	0x32000000    /* LB sdram refresh timer, about 6us */
+#define CONFIG_SYS_LBC_MRTPR	0x20000000    /* LB refresh timer prescal, 266MHz/32 */
 
 /*
  * LSDMR masks
  */
-#define CFG_LBC_LSDMR_RFEN	(1 << (31 -  1))
-#define CFG_LBC_LSDMR_BSMA1516	(3 << (31 - 10))
-#define CFG_LBC_LSDMR_BSMA1617	(4 << (31 - 10))
-#define CFG_LBC_LSDMR_RFCR5	(3 << (31 - 16))
-#define CFG_LBC_LSDMR_RFCR8	(5 << (31 - 16))
-#define CFG_LBC_LSDMR_RFCR16	(7 << (31 - 16))
-#define CFG_LBC_LSDMR_PRETOACT3	(3 << (31 - 19))
-#define CFG_LBC_LSDMR_PRETOACT6	(5 << (31 - 19))
-#define CFG_LBC_LSDMR_PRETOACT7	(7 << (31 - 19))
-#define CFG_LBC_LSDMR_ACTTORW3	(3 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW7	(7 << (31 - 22))
-#define CFG_LBC_LSDMR_ACTTORW6	(6 << (31 - 22))
-#define CFG_LBC_LSDMR_BL8	(1 << (31 - 23))
-#define CFG_LBC_LSDMR_WRC2	(2 << (31 - 27))
-#define CFG_LBC_LSDMR_WRC3	(3 << (31 - 27))
-#define CFG_LBC_LSDMR_WRC4	(0 << (31 - 27))
-#define CFG_LBC_LSDMR_BUFCMD	(1 << (31 - 29))
-#define CFG_LBC_LSDMR_CL3	(3 << (31 - 31))
-
-#define CFG_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
-
-#define CFG_LBC_LSDMR_COMMON    ( CFG_LBC_LSDMR_RFEN            \
-				| CFG_LBC_LSDMR_BSMA1516	\
-				| CFG_LBC_LSDMR_RFCR8		\
-				| CFG_LBC_LSDMR_PRETOACT6	\
-				| CFG_LBC_LSDMR_ACTTORW3	\
-				| CFG_LBC_LSDMR_BL8		\
-				| CFG_LBC_LSDMR_WRC3		\
-				| CFG_LBC_LSDMR_CL3		\
+#define CONFIG_SYS_LBC_LSDMR_RFEN	(1 << (31 -  1))
+#define CONFIG_SYS_LBC_LSDMR_BSMA1516	(3 << (31 - 10))
+#define CONFIG_SYS_LBC_LSDMR_BSMA1617	(4 << (31 - 10))
+#define CONFIG_SYS_LBC_LSDMR_RFCR5	(3 << (31 - 16))
+#define CONFIG_SYS_LBC_LSDMR_RFCR8	(5 << (31 - 16))
+#define CONFIG_SYS_LBC_LSDMR_RFCR16	(7 << (31 - 16))
+#define CONFIG_SYS_LBC_LSDMR_PRETOACT3	(3 << (31 - 19))
+#define CONFIG_SYS_LBC_LSDMR_PRETOACT6	(5 << (31 - 19))
+#define CONFIG_SYS_LBC_LSDMR_PRETOACT7	(7 << (31 - 19))
+#define CONFIG_SYS_LBC_LSDMR_ACTTORW3	(3 << (31 - 22))
+#define CONFIG_SYS_LBC_LSDMR_ACTTORW7	(7 << (31 - 22))
+#define CONFIG_SYS_LBC_LSDMR_ACTTORW6	(6 << (31 - 22))
+#define CONFIG_SYS_LBC_LSDMR_BL8	(1 << (31 - 23))
+#define CONFIG_SYS_LBC_LSDMR_WRC2	(2 << (31 - 27))
+#define CONFIG_SYS_LBC_LSDMR_WRC3	(3 << (31 - 27))
+#define CONFIG_SYS_LBC_LSDMR_WRC4	(0 << (31 - 27))
+#define CONFIG_SYS_LBC_LSDMR_BUFCMD	(1 << (31 - 29))
+#define CONFIG_SYS_LBC_LSDMR_CL3	(3 << (31 - 31))
+
+#define CONFIG_SYS_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
+
+#define CONFIG_SYS_LBC_LSDMR_COMMON    ( CONFIG_SYS_LBC_LSDMR_RFEN            \
+				| CONFIG_SYS_LBC_LSDMR_BSMA1516	\
+				| CONFIG_SYS_LBC_LSDMR_RFCR8		\
+				| CONFIG_SYS_LBC_LSDMR_PRETOACT6	\
+				| CONFIG_SYS_LBC_LSDMR_ACTTORW3	\
+				| CONFIG_SYS_LBC_LSDMR_BL8		\
+				| CONFIG_SYS_LBC_LSDMR_WRC3		\
+				| CONFIG_SYS_LBC_LSDMR_CL3		\
 				)
 
 /*
  * SDRAM Controller configuration sequence.
  */
-#define CFG_LBC_LSDMR_1		( CFG_LBC_LSDMR_COMMON \
-				| CFG_LBC_LSDMR_OP_PCHALL)
-#define CFG_LBC_LSDMR_2		( CFG_LBC_LSDMR_COMMON \
-				| CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_3		( CFG_LBC_LSDMR_COMMON \
-				| CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_4		( CFG_LBC_LSDMR_COMMON \
-				| CFG_LBC_LSDMR_OP_MRW)
-#define CFG_LBC_LSDMR_5		( CFG_LBC_LSDMR_COMMON \
-				| CFG_LBC_LSDMR_OP_NORMAL)
+#define CONFIG_SYS_LBC_LSDMR_1		( CONFIG_SYS_LBC_LSDMR_COMMON \
+				| CONFIG_SYS_LBC_LSDMR_OP_PCHALL)
+#define CONFIG_SYS_LBC_LSDMR_2		( CONFIG_SYS_LBC_LSDMR_COMMON \
+				| CONFIG_SYS_LBC_LSDMR_OP_ARFRSH)
+#define CONFIG_SYS_LBC_LSDMR_3		( CONFIG_SYS_LBC_LSDMR_COMMON \
+				| CONFIG_SYS_LBC_LSDMR_OP_ARFRSH)
+#define CONFIG_SYS_LBC_LSDMR_4		( CONFIG_SYS_LBC_LSDMR_COMMON \
+				| CONFIG_SYS_LBC_LSDMR_OP_MRW)
+#define CONFIG_SYS_LBC_LSDMR_5		( CONFIG_SYS_LBC_LSDMR_COMMON \
+				| CONFIG_SYS_LBC_LSDMR_OP_NORMAL)
 #endif
 
 /*
@@ -323,22 +323,22 @@
  */
 #define CONFIG_CONS_INDEX     1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE    1
-#define CFG_NS16550_CLK		get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
 
-#define CFG_BAUDRATE_TABLE  \
+#define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-#define CFG_NS16550_COM1        (CFG_IMMR+0x4500)
-#define CFG_NS16550_COM2        (CFG_IMMR+0x4600)
+#define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 /* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef  CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef  CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 #endif
 
 /* pass open firmware flat tree */
@@ -352,53 +352,53 @@
 #define CONFIG_FSL_I2C
 #define CONFIG_I2C_MULTI_BUS
 #define CONFIG_I2C_CMD_TREE
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address */
-#define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_NOPROBES	{{0,0x69}}	/* Don't probe these addrs */
-#define CFG_I2C_OFFSET		0x3000
-#define CFG_I2C2_OFFSET		0x3100
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_NOPROBES	{{0,0x69}}	/* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET		0x3000
+#define CONFIG_SYS_I2C2_OFFSET		0x3100
 
 /* SPI */
 #define CONFIG_MPC8XXX_SPI
 #undef CONFIG_SOFT_SPI			/* SPI bit-banged */
 
 /* GPIOs.  Used as SPI chip selects */
-#define CFG_GPIO1_PRELIM
-#define CFG_GPIO1_DIR		0xC0000000  /* SPI CS on 0, LED on 1 */
-#define CFG_GPIO1_DAT		0xC0000000  /* Both are active LOW */
+#define CONFIG_SYS_GPIO1_PRELIM
+#define CONFIG_SYS_GPIO1_DIR		0xC0000000  /* SPI CS on 0, LED on 1 */
+#define CONFIG_SYS_GPIO1_DAT		0xC0000000  /* Both are active LOW */
 
 /* TSEC */
-#define CFG_TSEC1_OFFSET 0x24000
-#define CFG_TSEC1 (CFG_IMMR+CFG_TSEC1_OFFSET)
-#define CFG_TSEC2_OFFSET 0x25000
-#define CFG_TSEC2 (CFG_IMMR+CFG_TSEC2_OFFSET)
+#define CONFIG_SYS_TSEC1_OFFSET 0x24000
+#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
+#define CONFIG_SYS_TSEC2_OFFSET 0x25000
+#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)
 
 /* USB */
-#define CFG_USE_MPC834XSYS_USB_PHY	1 /* Use SYS board PHY */
+#define CONFIG_SYS_USE_MPC834XSYS_USB_PHY	1 /* Use SYS board PHY */
 
 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
-#define CFG_PCI1_MEM_BASE	0x80000000
-#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
-#define CFG_PCI1_MMIO_BASE	0x90000000
-#define CFG_PCI1_MMIO_PHYS	CFG_PCI1_MMIO_BASE
-#define CFG_PCI1_MMIO_SIZE	0x10000000	/* 256M */
-#define CFG_PCI1_IO_BASE	0x00000000
-#define CFG_PCI1_IO_PHYS	0xE2000000
-#define CFG_PCI1_IO_SIZE	0x00100000	/* 1M */
-
-#define CFG_PCI2_MEM_BASE	0xA0000000
-#define CFG_PCI2_MEM_PHYS	CFG_PCI2_MEM_BASE
-#define CFG_PCI2_MEM_SIZE	0x10000000	/* 256M */
-#define CFG_PCI2_MMIO_BASE	0xB0000000
-#define CFG_PCI2_MMIO_PHYS	CFG_PCI2_MMIO_BASE
-#define CFG_PCI2_MMIO_SIZE	0x10000000	/* 256M */
-#define CFG_PCI2_IO_BASE	0x00000000
-#define CFG_PCI2_IO_PHYS	0xE2100000
-#define CFG_PCI2_IO_SIZE	0x00100000	/* 1M */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE	0x00000000
+#define CONFIG_SYS_PCI1_IO_PHYS	0xE2000000
+#define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
+
+#define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
+#define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
+#define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
+#define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
+#define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI2_IO_BASE	0x00000000
+#define CONFIG_SYS_PCI2_IO_PHYS	0xE2100000
+#define CONFIG_SYS_PCI2_IO_SIZE	0x00100000	/* 1M */
 
 #if defined(CONFIG_PCI)
 
@@ -424,7 +424,7 @@
 #endif
 
 #undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID 0x1957  /* Freescale */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957  /* Freescale */
 
 #endif	/* CONFIG_PCI */
 
@@ -459,30 +459,30 @@
  * Configure on-board RTC
  */
 #define CONFIG_RTC_DS1374			/* use ds1374 rtc via i2c	*/
-#define CFG_I2C_RTC_ADDR		0x68	/* at address 0x68		*/
+#define CONFIG_SYS_I2C_RTC_ADDR		0x68	/* at address 0x68		*/
 
 /*
  * Environment
  */
-#ifndef CFG_RAMBOOT
-	#define CFG_ENV_IS_IN_FLASH	1
-	#define CFG_ENV_ADDR		(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
-	#define CFG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env */
-	#define CFG_ENV_SIZE		0x2000
+#ifndef CONFIG_SYS_RAMBOOT
+	#define CONFIG_ENV_IS_IN_FLASH	1
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env */
+	#define CONFIG_ENV_SIZE		0x2000
 
 /* Address and size of Redundant Environment Sector	*/
-#define CFG_ENV_ADDR_REDUND	(CFG_ENV_ADDR + CFG_ENV_SECT_SIZE)
-#define CFG_ENV_SIZE_REDUND	(CFG_ENV_SIZE)
+#define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
 
 #else
-	#define CFG_NO_FLASH		1	/* Flash is not usable now */
-	#define CFG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
-	#define CFG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
-	#define CFG_ENV_SIZE		0x2000
+	#define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
+	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
+	#define CONFIG_ENV_SIZE		0x2000
 #endif
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
 
 /*
@@ -508,7 +508,7 @@
     #define CONFIG_CMD_PCI
 #endif
 
-#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
     #undef CONFIG_CMD_ENV
     #undef CONFIG_CMD_LOADS
 #endif
@@ -519,60 +519,60 @@
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP			/* undef to save memory */
-#define CFG_LOAD_ADDR	0x2000000	/* default load address */
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP			/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt */
 
 #if defined(CONFIG_CMD_KGDB)
-	#define CFG_CBSIZE	1024		/* Console I/O Buffer Size */
+	#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size */
 #else
-	#define CFG_CBSIZE	256		/* Console I/O Buffer Size */
+	#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size */
 #endif
 
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args */
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
-#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
+#define CONFIG_SYS_BOOTMAPSZ	(8 << 20)	/* Initial Memory map for Linux*/
 
-#define CFG_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
+#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */
 
 #if 1 /*528/264*/
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN |\
 	HRCWL_VCO_1X2 |\
 	HRCWL_CORE_TO_CSB_2X1)
 #elif 0 /*396/132*/
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN |\
 	HRCWL_VCO_1X4 |\
 	HRCWL_CORE_TO_CSB_3X1)
 #elif 0 /*264/132*/
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN |\
 	HRCWL_VCO_1X4 |\
 	HRCWL_CORE_TO_CSB_2X1)
 #elif 0 /*132/132*/
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN |\
 	HRCWL_VCO_1X4 |\
 	HRCWL_CORE_TO_CSB_1X1)
 #elif 0 /*264/264 */
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_1X1 |\
 	HRCWL_CSB_TO_CLKIN |\
@@ -581,7 +581,7 @@
 #endif
 
 #ifdef CONFIG_PCISLAVE
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
 	HRCWH_PCI_AGENT |\
 	HRCWH_64_BIT_PCI |\
 	HRCWH_PCI1_ARBITER_DISABLE |\
@@ -595,7 +595,7 @@
 	HRCWH_TSEC2M_IN_GMII )
 #else
 #if defined(PCI_64BIT)
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
 	HRCWH_PCI_HOST |\
 	HRCWH_64_BIT_PCI |\
 	HRCWH_PCI1_ARBITER_ENABLE |\
@@ -608,7 +608,7 @@
 	HRCWH_TSEC1M_IN_GMII |\
 	HRCWH_TSEC2M_IN_GMII )
 #else
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
 	HRCWH_PCI_HOST |\
 	HRCWH_32_BIT_PCI |\
 	HRCWH_PCI1_ARBITER_ENABLE |\
@@ -626,85 +626,85 @@
 /*
  * System performance
  */
-#define CFG_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
-#define CFG_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
-#define CFG_SPCR_TSEC1EP	3	/* TSEC1 emergency priority (0-3) */
-#define CFG_SPCR_TSEC2EP	3	/* TSEC2 emergency priority (0-3) */
-#define CFG_SCCR_TSEC1CM	1	/* TSEC1 clock mode (0-3) */
-#define CFG_SCCR_TSEC2CM	1	/* TSEC2 & I2C0 clock mode (0-3) */
+#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
+#define CONFIG_SYS_SPCR_TSEC1EP	3	/* TSEC1 emergency priority (0-3) */
+#define CONFIG_SYS_SPCR_TSEC2EP	3	/* TSEC2 emergency priority (0-3) */
+#define CONFIG_SYS_SCCR_TSEC1CM	1	/* TSEC1 clock mode (0-3) */
+#define CONFIG_SYS_SCCR_TSEC2CM	1	/* TSEC2 & I2C0 clock mode (0-3) */
 
 /* System IO Config */
-#define CFG_SICRH SICRH_TSOBI1
-#define CFG_SICRL SICRL_LDP_A
+#define CONFIG_SYS_SICRH SICRH_TSOBI1
+#define CONFIG_SYS_SICRL SICRL_LDP_A
 
-#define CFG_HID0_INIT	0x000000000
-#define CFG_HID0_FINAL	HID0_ENABLE_MACHINE_CHECK
+#define CONFIG_SYS_HID0_INIT	0x000000000
+#define CONFIG_SYS_HID0_FINAL	HID0_ENABLE_MACHINE_CHECK
 
-/* #define CFG_HID0_FINAL		(\
+/* #define CONFIG_SYS_HID0_FINAL		(\
 	HID0_ENABLE_INSTRUCTION_CACHE |\
 	HID0_ENABLE_M_BIT |\
 	HID0_ENABLE_ADDRESS_BROADCAST ) */
 
 
-#define CFG_HID2 HID2_HBE
+#define CONFIG_SYS_HID2 HID2_HBE
 #define CONFIG_HIGH_BATS	1	/* High BATs supported */
 
 /* DDR @ 0x00000000 */
-#define CFG_IBAT0L	(CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT0U	(CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 
 /* PCI @ 0x80000000 */
 #ifdef CONFIG_PCI
-#define CFG_IBAT1L	(CFG_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT1U	(CFG_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT2L	(CFG_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT2U	(CFG_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_PCI1_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_PCI1_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_PCI1_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_PCI1_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 #else
-#define CFG_IBAT1L	(0)
-#define CFG_IBAT1U	(0)
-#define CFG_IBAT2L	(0)
-#define CFG_IBAT2U	(0)
+#define CONFIG_SYS_IBAT1L	(0)
+#define CONFIG_SYS_IBAT1U	(0)
+#define CONFIG_SYS_IBAT2L	(0)
+#define CONFIG_SYS_IBAT2U	(0)
 #endif
 
 #ifdef CONFIG_MPC83XX_PCI2
-#define CFG_IBAT3L	(CFG_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT3U	(CFG_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_IBAT4L	(CFG_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT4U	(CFG_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L	(CONFIG_SYS_PCI2_MEM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT3U	(CONFIG_SYS_PCI2_MEM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_PCI2_MMIO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_PCI2_MMIO_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 #else
-#define CFG_IBAT3L	(0)
-#define CFG_IBAT3U	(0)
-#define CFG_IBAT4L	(0)
-#define CFG_IBAT4U	(0)
+#define CONFIG_SYS_IBAT3L	(0)
+#define CONFIG_SYS_IBAT3U	(0)
+#define CONFIG_SYS_IBAT4L	(0)
+#define CONFIG_SYS_IBAT4U	(0)
 #endif
 
 /* IMMRBAR @ 0xE0000000, PCI IO @ 0xE2000000 & BCSR @ 0xE2400000 */
-#define CFG_IBAT5L	(CFG_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT5U	(CFG_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_IMMR | BATL_PP_10 | BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
+#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_IMMR | BATU_BL_256M | BATU_VS | BATU_VP)
 
 /* SDRAM @ 0xF0000000, stack in DCACHE 0xFDF00000 & FLASH @ 0xFE000000 */
-#define CFG_IBAT6L	(0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
-
-#define CFG_IBAT7L	(0)
-#define CFG_IBAT7U	(0)
-
-#define CFG_DBAT0L	CFG_IBAT0L
-#define CFG_DBAT0U	CFG_IBAT0U
-#define CFG_DBAT1L	CFG_IBAT1L
-#define CFG_DBAT1U	CFG_IBAT1U
-#define CFG_DBAT2L	CFG_IBAT2L
-#define CFG_DBAT2U	CFG_IBAT2U
-#define CFG_DBAT3L	CFG_IBAT3L
-#define CFG_DBAT3U	CFG_IBAT3U
-#define CFG_DBAT4L	CFG_IBAT4L
-#define CFG_DBAT4U	CFG_IBAT4U
-#define CFG_DBAT5L	CFG_IBAT5L
-#define CFG_DBAT5U	CFG_IBAT5U
-#define CFG_DBAT6L	CFG_IBAT6L
-#define CFG_DBAT6U	CFG_IBAT6U
-#define CFG_DBAT7L	CFG_IBAT7L
-#define CFG_DBAT7U	CFG_IBAT7U
+#define CONFIG_SYS_IBAT6L	(0xF0000000 | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT6U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+
+#define CONFIG_SYS_IBAT7L	(0)
+#define CONFIG_SYS_IBAT7U	(0)
+
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
+#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
+#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 
 /*
  * Internal Definitions