rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

1 files changed, 187 insertions, 187 deletions

diff --git a/include/configs/MPC8323ERDB.h b/include/configs/MPC8323ERDB.h
index b95f54d..c6ac91a 100644
--- a/include/configs/MPC8323ERDB.h
+++ b/include/configs/MPC8323ERDB.h
@@ -32,7 +32,7 @@
 /*
  * Hardware Reset Configuration Word
  */
-#define CFG_HRCW_LOW (\
+#define CONFIG_SYS_HRCW_LOW (\
 	HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
 	HRCWL_DDR_TO_SCB_CLK_2X1 |\
 	HRCWL_VCO_1X2 |\
@@ -42,7 +42,7 @@
 	HRCWL_CE_PLL_DIV_1X1 |\
 	HRCWL_CE_TO_PLL_1X3)
 
-#define CFG_HRCW_HIGH (\
+#define CONFIG_SYS_HRCW_HIGH (\
 	HRCWH_PCI_HOST |\
 	HRCWH_PCI1_ARBITER_ENABLE |\
 	HRCWH_CORE_ENABLE |\
@@ -56,29 +56,29 @@
 /*
  * System IO Config
  */
-#define CFG_SICRL		0x00000000
+#define CONFIG_SYS_SICRL		0x00000000
 
 #define CONFIG_BOARD_EARLY_INIT_F	/* call board_pre_init */
 
 /*
  * IMMR new address
  */
-#define CFG_IMMR		0xE0000000
+#define CONFIG_SYS_IMMR		0xE0000000
 
 /*
  * System performance
  */
-#define CFG_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
-#define CFG_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
-#define CFG_SPCR_OPT		1	/* (0-1) Optimize transactions between  CSB and the SEC and QUICC Engine block */
+#define CONFIG_SYS_ACR_PIPE_DEP	3	/* Arbiter pipeline depth (0-3) */
+#define CONFIG_SYS_ACR_RPTCNT		3	/* Arbiter repeat count (0-7) */
+#define CONFIG_SYS_SPCR_OPT		1	/* (0-1) Optimize transactions between  CSB and the SEC and QUICC Engine block */
 
 /*
  * DDR Setup
  */
-#define CFG_DDR_BASE		0x00000000	/* DDR is system memory */
-#define CFG_SDRAM_BASE		CFG_DDR_BASE
-#define CFG_DDR_SDRAM_BASE	CFG_DDR_BASE
-#define CFG_DDRCDR		0x73000002	/* DDR II voltage is 1.8V */
+#define CONFIG_SYS_DDR_BASE		0x00000000	/* DDR is system memory */
+#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDR_SDRAM_BASE	CONFIG_SYS_DDR_BASE
+#define CONFIG_SYS_DDRCDR		0x73000002	/* DDR II voltage is 1.8V */
 
 #undef CONFIG_SPD_EEPROM
 #if defined(CONFIG_SPD_EEPROM)
@@ -88,12 +88,12 @@
 #else
 /* Manually set up DDR parameters
  */
-#define CFG_DDR_SIZE		64	/* MB */
-#define CFG_DDR_CS0_CONFIG	( CSCONFIG_EN \
+#define CONFIG_SYS_DDR_SIZE		64	/* MB */
+#define CONFIG_SYS_DDR_CS0_CONFIG	( CSCONFIG_EN \
 				| CSCONFIG_ODT_WR_ACS \
 				| CSCONFIG_ROW_BIT_13 | CSCONFIG_COL_BIT_9 )
 				/* 0x80010101 */
-#define CFG_DDR_TIMING_0	( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_0	( ( 0 << TIMING_CFG0_RWT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_WRT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_RRT_SHIFT ) \
 				| ( 0 << TIMING_CFG0_WWT_SHIFT ) \
@@ -102,7 +102,7 @@
 				| ( 8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT ) \
 				| ( 2 << TIMING_CFG0_MRS_CYC_SHIFT ) )
 				/* 0x00220802 */
-#define CFG_DDR_TIMING_1	( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_1	( ( 2 << TIMING_CFG1_PRETOACT_SHIFT ) \
 				| ( 6 << TIMING_CFG1_ACTTOPRE_SHIFT ) \
 				| ( 2 << TIMING_CFG1_ACTTORW_SHIFT ) \
 				| ( 5 << TIMING_CFG1_CASLAT_SHIFT ) \
@@ -111,7 +111,7 @@
 				| ( 2 << TIMING_CFG1_ACTTOACT_SHIFT ) \
 				| ( 2 << TIMING_CFG1_WRTORD_SHIFT ) )
 				/* 0x26253222 */
-#define CFG_DDR_TIMING_2	( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
+#define CONFIG_SYS_DDR_TIMING_2	( ( 1 << TIMING_CFG2_ADD_LAT_SHIFT ) \
 				| (31 << TIMING_CFG2_CPO_SHIFT ) \
 				| ( 2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT ) \
 				| ( 2 << TIMING_CFG2_RD_TO_PRE_SHIFT ) \
@@ -119,99 +119,99 @@
 				| ( 3 << TIMING_CFG2_CKE_PLS_SHIFT ) \
 				| ( 7 << TIMING_CFG2_FOUR_ACT_SHIFT) )
 				/* 0x1f9048c7 */
-#define CFG_DDR_TIMING_3	0x00000000
-#define CFG_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
+#define CONFIG_SYS_DDR_TIMING_3	0x00000000
+#define CONFIG_SYS_DDR_CLK_CNTL	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
 				/* 0x02000000 */
-#define CFG_DDR_MODE		( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
+#define CONFIG_SYS_DDR_MODE		( ( 0x4448 << SDRAM_MODE_ESD_SHIFT ) \
 				| ( 0x0232 << SDRAM_MODE_SD_SHIFT ) )
 				/* 0x44480232 */
-#define CFG_DDR_MODE2		0x8000c000
-#define CFG_DDR_INTERVAL	( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
+#define CONFIG_SYS_DDR_MODE2		0x8000c000
+#define CONFIG_SYS_DDR_INTERVAL	( ( 800 << SDRAM_INTERVAL_REFINT_SHIFT ) \
 				| ( 100 << SDRAM_INTERVAL_BSTOPRE_SHIFT ) )
 				/* 0x03200064 */
-#define CFG_DDR_CS0_BNDS	0x00000003
-#define CFG_DDR_SDRAM_CFG	( SDRAM_CFG_SREN \
+#define CONFIG_SYS_DDR_CS0_BNDS	0x00000003
+#define CONFIG_SYS_DDR_SDRAM_CFG	( SDRAM_CFG_SREN \
 				| SDRAM_CFG_SDRAM_TYPE_DDR2 \
 				| SDRAM_CFG_32_BE )
 				/* 0x43080000 */
-#define CFG_DDR_SDRAM_CFG2	0x00401000
+#define CONFIG_SYS_DDR_SDRAM_CFG2	0x00401000
 #endif
 
 /*
  * Memory test
  */
-#undef CFG_DRAM_TEST		/* memory test, takes time */
-#define CFG_MEMTEST_START	0x00030000	/* memtest region */
-#define CFG_MEMTEST_END		0x03f00000
+#undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
+#define CONFIG_SYS_MEMTEST_START	0x00030000	/* memtest region */
+#define CONFIG_SYS_MEMTEST_END		0x03f00000
 
 /*
  * The reserved memory
  */
-#define CFG_MONITOR_BASE	TEXT_BASE	/* start of monitor */
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE	/* start of monitor */
 
-#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
-#define CFG_RAMBOOT
+#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
+#define CONFIG_SYS_RAMBOOT
 #else
-#undef  CFG_RAMBOOT
+#undef  CONFIG_SYS_RAMBOOT
 #endif
 
-/* CFG_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
+/* CONFIG_SYS_MONITOR_LEN must be a multiple of CONFIG_ENV_SECT_SIZE */
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Mon */
+#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserved for malloc */
 
 /*
  * Initial RAM Base Address Setup
  */
-#define CFG_INIT_RAM_LOCK	1
-#define CFG_INIT_RAM_ADDR	0xE6000000	/* Initial RAM address */
-#define CFG_INIT_RAM_END	0x1000		/* End of used area in RAM */
-#define CFG_GBL_DATA_SIZE	0x100		/* num bytes initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_LOCK	1
+#define CONFIG_SYS_INIT_RAM_ADDR	0xE6000000	/* Initial RAM address */
+#define CONFIG_SYS_INIT_RAM_END	0x1000		/* End of used area in RAM */
+#define CONFIG_SYS_GBL_DATA_SIZE	0x100		/* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 
 /*
  * Local Bus Configuration & Clock Setup
  */
-#define CFG_LCRR		(LCRR_DBYP | LCRR_CLKDIV_2)
-#define CFG_LBC_LBCR		0x00000000
+#define CONFIG_SYS_LCRR		(LCRR_DBYP | LCRR_CLKDIV_2)
+#define CONFIG_SYS_LBC_LBCR		0x00000000
 
 /*
  * FLASH on the Local Bus
  */
-#define CFG_FLASH_CFI		/* use the Common Flash Interface */
+#define CONFIG_SYS_FLASH_CFI		/* use the Common Flash Interface */
 #define CONFIG_FLASH_CFI_DRIVER	/* use the CFI driver */
-#define CFG_FLASH_BASE		0xFE000000	/* FLASH base address */
-#define CFG_FLASH_SIZE		16	/* FLASH size is 16M */
-#define CFG_FLASH_PROTECTION	1		/* Use h/w Flash protection. */
+#define CONFIG_SYS_FLASH_BASE		0xFE000000	/* FLASH base address */
+#define CONFIG_SYS_FLASH_SIZE		16	/* FLASH size is 16M */
+#define CONFIG_SYS_FLASH_PROTECTION	1		/* Use h/w Flash protection. */
 
-#define CFG_LBLAWBAR0_PRELIM	CFG_FLASH_BASE	/* Window base at flash base */
-#define CFG_LBLAWAR0_PRELIM	0x80000018	/* 32MB window size */
+#define CONFIG_SYS_LBLAWBAR0_PRELIM	CONFIG_SYS_FLASH_BASE	/* Window base at flash base */
+#define CONFIG_SYS_LBLAWAR0_PRELIM	0x80000018	/* 32MB window size */
 
-#define CFG_BR0_PRELIM	(CFG_FLASH_BASE |	/* Flash Base address */ \
+#define CONFIG_SYS_BR0_PRELIM	(CONFIG_SYS_FLASH_BASE |	/* Flash Base address */ \
 			(2 << BR_PS_SHIFT) |	/* 16 bit port size */ \
 			BR_V)			/* valid */
-#define CFG_OR0_PRELIM		0xfe006ff7	/* 16MB Flash size */
+#define CONFIG_SYS_OR0_PRELIM		0xfe006ff7	/* 16MB Flash size */
 
-#define CFG_MAX_FLASH_BANKS	1		/* number of banks */
-#define CFG_MAX_FLASH_SECT	128		/* sectors per device */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1		/* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	128		/* sectors per device */
 
-#undef CFG_FLASH_CHECKSUM
+#undef CONFIG_SYS_FLASH_CHECKSUM
 
 /*
  * SDRAM on the Local Bus
  */
-#undef CFG_LB_SDRAM		/* The board has not SRDAM on local bus */
+#undef CONFIG_SYS_LB_SDRAM		/* The board has not SRDAM on local bus */
 
-#ifdef CFG_LB_SDRAM
-#define CFG_LBC_SDRAM_BASE	0xF0000000	/* SDRAM base address */
-#define CFG_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
+#ifdef CONFIG_SYS_LB_SDRAM
+#define CONFIG_SYS_LBC_SDRAM_BASE	0xF0000000	/* SDRAM base address */
+#define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */
 
-#define CFG_LBLAWBAR2_PRELIM	CFG_LBC_SDRAM_BASE
-#define CFG_LBLAWAR2_PRELIM	0x80000019	/* 64MB */
+#define CONFIG_SYS_LBLAWBAR2_PRELIM	CONFIG_SYS_LBC_SDRAM_BASE
+#define CONFIG_SYS_LBLAWAR2_PRELIM	0x80000019	/* 64MB */
 
 /*local bus BR2, OR2 definition for SDRAM if soldered on the EPB board */
 /*
  * Base Register 2 and Option Register 2 configure SDRAM.
- * The SDRAM base address, CFG_LBC_SDRAM_BASE, is 0xf0000000.
+ * The SDRAM base address, CONFIG_SYS_LBC_SDRAM_BASE, is 0xf0000000.
  *
  * For BR2, need:
  *    Base address of 0xf0000000 = BR[0:16] = 1111 0000 0000 0000 0
@@ -223,14 +223,14 @@
  * 0    4    8    12   16   20   24   28
  * 1111 0000 0000 0000 0001 1000 0110 0001 = f0001861
  *
- * CFG_LBC_SDRAM_BASE should be masked and OR'ed into
+ * CONFIG_SYS_LBC_SDRAM_BASE should be masked and OR'ed into
  * the top 17 bits of BR2.
  */
 
-#define CFG_BR2_PRELIM	0xf0001861	/*Port size=32bit, MSEL=SDRAM */
+#define CONFIG_SYS_BR2_PRELIM	0xf0001861	/*Port size=32bit, MSEL=SDRAM */
 
 /*
- * The SDRAM size in MB, CFG_LBC_SDRAM_SIZE, is 64.
+ * The SDRAM size in MB, CONFIG_SYS_LBC_SDRAM_SIZE, is 64.
  *
  * For OR2, need:
  *    64MB mask for AM, OR2[0:7] = 1111 1100
@@ -243,68 +243,68 @@
  * 1111 1100 0000 0000 0110 1001 0000 0001 = fc006901
  */
 
-#define CFG_OR2_PRELIM	0xfc006901
+#define CONFIG_SYS_OR2_PRELIM	0xfc006901
 
-#define CFG_LBC_LSRT	0x32000000	/* LB sdram refresh timer, about 6us */
-#define CFG_LBC_MRTPR	0x20000000	/* LB refresh timer prescal, 266MHz/32 */
+#define CONFIG_SYS_LBC_LSRT	0x32000000	/* LB sdram refresh timer, about 6us */
+#define CONFIG_SYS_LBC_MRTPR	0x20000000	/* LB refresh timer prescal, 266MHz/32 */
 
 /*
  * LSDMR masks
  */
-#define CFG_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
-#define CFG_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_NORMAL	(0 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_ARFRSH	(1 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_SRFRSH	(2 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_MRW	(3 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_PRECH	(4 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_PCHALL	(5 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_ACTBNK	(6 << (31 - 4))
+#define CONFIG_SYS_LBC_LSDMR_OP_RWINV	(7 << (31 - 4))
 
-#define CFG_LBC_LSDMR_COMMON	0x0063b723
+#define CONFIG_SYS_LBC_LSDMR_COMMON	0x0063b723
 
 /*
  * SDRAM Controller configuration sequence.
  */
-#define CFG_LBC_LSDMR_1		( CFG_LBC_LSDMR_COMMON \
-				| CFG_LBC_LSDMR_OP_PCHALL)
-#define CFG_LBC_LSDMR_2		( CFG_LBC_LSDMR_COMMON \
-				| CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_3		( CFG_LBC_LSDMR_COMMON \
-				| CFG_LBC_LSDMR_OP_ARFRSH)
-#define CFG_LBC_LSDMR_4		( CFG_LBC_LSDMR_COMMON \
-				| CFG_LBC_LSDMR_OP_MRW)
-#define CFG_LBC_LSDMR_5		( CFG_LBC_LSDMR_COMMON \
-				| CFG_LBC_LSDMR_OP_NORMAL)
+#define CONFIG_SYS_LBC_LSDMR_1		( CONFIG_SYS_LBC_LSDMR_COMMON \
+				| CONFIG_SYS_LBC_LSDMR_OP_PCHALL)
+#define CONFIG_SYS_LBC_LSDMR_2		( CONFIG_SYS_LBC_LSDMR_COMMON \
+				| CONFIG_SYS_LBC_LSDMR_OP_ARFRSH)
+#define CONFIG_SYS_LBC_LSDMR_3		( CONFIG_SYS_LBC_LSDMR_COMMON \
+				| CONFIG_SYS_LBC_LSDMR_OP_ARFRSH)
+#define CONFIG_SYS_LBC_LSDMR_4		( CONFIG_SYS_LBC_LSDMR_COMMON \
+				| CONFIG_SYS_LBC_LSDMR_OP_MRW)
+#define CONFIG_SYS_LBC_LSDMR_5		( CONFIG_SYS_LBC_LSDMR_COMMON \
+				| CONFIG_SYS_LBC_LSDMR_OP_NORMAL)
 
 #endif
 
 /*
  * Windows to access PIB via local bus
  */
-#define CFG_LBLAWBAR3_PRELIM	0xf8008000	/* windows base 0xf8008000 */
-#define CFG_LBLAWAR3_PRELIM	0x8000000f	/* windows size 64KB */
+#define CONFIG_SYS_LBLAWBAR3_PRELIM	0xf8008000	/* windows base 0xf8008000 */
+#define CONFIG_SYS_LBLAWAR3_PRELIM	0x8000000f	/* windows size 64KB */
 
 /*
  * Serial Port
  */
 #define CONFIG_CONS_INDEX	1
 #undef CONFIG_SERIAL_SOFTWARE_FIFO
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
-#define CFG_NS16550_REG_SIZE	1
-#define CFG_NS16550_CLK		get_bus_freq(0)
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)
 
-#define CFG_BAUDRATE_TABLE  \
+#define CONFIG_SYS_BAUDRATE_TABLE  \
 	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
 
-#define CFG_NS16550_COM1	(CFG_IMMR+0x4500)
-#define CFG_NS16550_COM2	(CFG_IMMR+0x4600)
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_IMMR+0x4500)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_IMMR+0x4600)
 
 #define CONFIG_CMDLINE_EDITING	1	/* add command line history */
 /* Use the HUSH parser */
-#define CFG_HUSH_PARSER
-#ifdef CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2 "> "
+#define CONFIG_SYS_HUSH_PARSER
+#ifdef CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 #endif
 
 /* pass open firmware flat tree */
@@ -316,32 +316,32 @@
 #define CONFIG_HARD_I2C		/* I2C with hardware support */
 #undef CONFIG_SOFT_I2C		/* I2C bit-banged */
 #define CONFIG_FSL_I2C
-#define CFG_I2C_SPEED	400000	/* I2C speed and slave address */
-#define CFG_I2C_SLAVE	0x7F
-#define CFG_I2C_NOPROBES	{0x51}	/* Don't probe these addrs */
-#define CFG_I2C_OFFSET	0x3000
+#define CONFIG_SYS_I2C_SPEED	400000	/* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE	0x7F
+#define CONFIG_SYS_I2C_NOPROBES	{0x51}	/* Don't probe these addrs */
+#define CONFIG_SYS_I2C_OFFSET	0x3000
 
 /*
  * Config on-board EEPROM
  */
-#define CFG_I2C_EEPROM_ADDR		0x50
-#define CFG_I2C_EEPROM_ADDR_LEN		2
-#define CFG_EEPROM_PAGE_WRITE_BITS	6
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10
+#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	6
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10
 
 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
-#define CFG_PCI1_MEM_BASE	0x80000000
-#define CFG_PCI1_MEM_PHYS	CFG_PCI1_MEM_BASE
-#define CFG_PCI1_MEM_SIZE	0x10000000	/* 256M */
-#define CFG_PCI1_MMIO_BASE	0x90000000
-#define CFG_PCI1_MMIO_PHYS	CFG_PCI1_MMIO_BASE
-#define CFG_PCI1_MMIO_SIZE	0x10000000	/* 256M */
-#define CFG_PCI1_IO_BASE		0xd0000000
-#define CFG_PCI1_IO_PHYS		CFG_PCI1_IO_BASE
-#define CFG_PCI1_IO_SIZE		0x04000000	/* 64M */
+#define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
+#define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
+#define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
+#define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
+#define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
+#define CONFIG_SYS_PCI1_IO_BASE		0xd0000000
+#define CONFIG_SYS_PCI1_IO_PHYS		CONFIG_SYS_PCI1_IO_BASE
+#define CONFIG_SYS_PCI1_IO_SIZE		0x04000000	/* 64M */
 
 #ifdef CONFIG_PCI
 #define CONFIG_PCI_SKIP_HOST_BRIDGE
@@ -350,7 +350,7 @@
 
 #undef CONFIG_EEPRO100
 #undef CONFIG_PCI_SCAN_SHOW	/* show pci devices on startup */
-#define CFG_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID	0x1957	/* Freescale */
 
 #endif	/* CONFIG_PCI */
 
@@ -368,42 +368,42 @@
 #define CONFIG_UEC_ETH1		/* ETH3 */
 
 #ifdef CONFIG_UEC_ETH1
-#define CFG_UEC1_UCC_NUM	2	/* UCC3 */
-#define CFG_UEC1_RX_CLK		QE_CLK9
-#define CFG_UEC1_TX_CLK		QE_CLK10
-#define CFG_UEC1_ETH_TYPE	FAST_ETH
-#define CFG_UEC1_PHY_ADDR	4
-#define CFG_UEC1_INTERFACE_MODE	ENET_100_MII
+#define CONFIG_SYS_UEC1_UCC_NUM	2	/* UCC3 */
+#define CONFIG_SYS_UEC1_RX_CLK		QE_CLK9
+#define CONFIG_SYS_UEC1_TX_CLK		QE_CLK10
+#define CONFIG_SYS_UEC1_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC1_PHY_ADDR	4
+#define CONFIG_SYS_UEC1_INTERFACE_MODE	ENET_100_MII
 #endif
 
 #define CONFIG_UEC_ETH2		/* ETH4 */
 
 #ifdef CONFIG_UEC_ETH2
-#define CFG_UEC2_UCC_NUM	1	/* UCC2 */
-#define CFG_UEC2_RX_CLK		QE_CLK16
-#define CFG_UEC2_TX_CLK		QE_CLK3
-#define CFG_UEC2_ETH_TYPE	FAST_ETH
-#define CFG_UEC2_PHY_ADDR	0
-#define CFG_UEC2_INTERFACE_MODE	ENET_100_MII
+#define CONFIG_SYS_UEC2_UCC_NUM	1	/* UCC2 */
+#define CONFIG_SYS_UEC2_RX_CLK		QE_CLK16
+#define CONFIG_SYS_UEC2_TX_CLK		QE_CLK3
+#define CONFIG_SYS_UEC2_ETH_TYPE	FAST_ETH
+#define CONFIG_SYS_UEC2_PHY_ADDR	0
+#define CONFIG_SYS_UEC2_INTERFACE_MODE	ENET_100_MII
 #endif
 
 /*
  * Environment
  */
-#ifndef CFG_RAMBOOT
+#ifndef CONFIG_SYS_RAMBOOT
 	#define CONFIG_ENV_IS_IN_FLASH	1
-	#define CONFIG_ENV_ADDR		(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 	#define CONFIG_ENV_SECT_SIZE	0x20000
 	#define CONFIG_ENV_SIZE		0x2000
 #else
-	#define CFG_NO_FLASH		1	/* Flash is not usable now */
+	#define CONFIG_SYS_NO_FLASH		1	/* Flash is not usable now */
 	#define CONFIG_ENV_IS_NOWHERE	1	/* Store ENV in memory only */
-	#define CONFIG_ENV_ADDR		(CFG_MONITOR_BASE - 0x1000)
+	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 	#define CONFIG_ENV_SIZE		0x2000
 #endif
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */
 
 /*
  * BOOTP options
@@ -426,7 +426,7 @@
 #if defined(CONFIG_PCI)
 	#define CONFIG_CMD_PCI
 #endif
-#if defined(CFG_RAMBOOT)
+#if defined(CONFIG_SYS_RAMBOOT)
 	#undef CONFIG_CMD_ENV
 	#undef CONFIG_CMD_LOADS
 #endif
@@ -436,34 +436,34 @@
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP		/* undef to save memory */
-#define CFG_LOAD_ADDR		0x2000000	/* default load address */
-#define CFG_PROMPT		"=> "	/* Monitor Command Prompt */
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR		0x2000000	/* default load address */
+#define CONFIG_SYS_PROMPT		"=> "	/* Monitor Command Prompt */
 
 #if (CONFIG_CMD_KGDB)
-	#define CFG_CBSIZE	1024	/* Console I/O Buffer Size */
+	#define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size */
 #else
-	#define CFG_CBSIZE	256	/* Console I/O Buffer Size */
+	#define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
 #endif
 
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args */
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size */
-#define CFG_HZ		1000		/* decrementer freq: 1ms ticks */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args */
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1ms ticks */
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*
  * Core HID Setup
  */
-#define CFG_HID0_INIT		0x000000000
-#define CFG_HID0_FINAL		HID0_ENABLE_MACHINE_CHECK
-#define CFG_HID2		HID2_HBE
+#define CONFIG_SYS_HID0_INIT		0x000000000
+#define CONFIG_SYS_HID0_FINAL		HID0_ENABLE_MACHINE_CHECK
+#define CONFIG_SYS_HID2		HID2_HBE
 
 /*
  * MMU Setup
@@ -471,64 +471,64 @@
 #define CONFIG_HIGH_BATS	1	/* High BATs supported */
 
 /* DDR: cache cacheable */
-#define CFG_IBAT0L	(CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT0U	(CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT0L	CFG_IBAT0L
-#define CFG_DBAT0U	CFG_IBAT0U
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
 
 /* IMMRBAR & PCI IO: cache-inhibit and guarded */
-#define CFG_IBAT1L	(CFG_IMMR | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_IMMR | BATL_PP_10 | \
 			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT1U	(CFG_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
-#define CFG_DBAT1L	CFG_IBAT1L
-#define CFG_DBAT1U	CFG_IBAT1U
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
 
 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
-#define CFG_IBAT2L	(CFG_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT2U	(CFG_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
-#define CFG_DBAT2L	(CFG_FLASH_BASE | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT2U	(CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT2L	(CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
 			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_DBAT2U	CFG_IBAT2U
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
 
-#define CFG_IBAT3L	(0)
-#define CFG_IBAT3U	(0)
-#define CFG_DBAT3L	CFG_IBAT3L
-#define CFG_DBAT3U	CFG_IBAT3U
+#define CONFIG_SYS_IBAT3L	(0)
+#define CONFIG_SYS_IBAT3U	(0)
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
 
 /* Stack in dcache: cacheable, no memory coherence */
-#define CFG_IBAT4L	(CFG_INIT_RAM_ADDR | BATL_PP_10)
-#define CFG_IBAT4U	(CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
-#define CFG_DBAT4L	CFG_IBAT4L
-#define CFG_DBAT4U	CFG_IBAT4U
+#define CONFIG_SYS_IBAT4L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
+#define CONFIG_SYS_IBAT4U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT4L	CONFIG_SYS_IBAT4L
+#define CONFIG_SYS_DBAT4U	CONFIG_SYS_IBAT4U
 
 #ifdef CONFIG_PCI
 /* PCI MEM space: cacheable */
-#define CFG_IBAT5L	(CFG_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT5U	(CFG_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT5L	CFG_IBAT5L
-#define CFG_DBAT5U	CFG_IBAT5U
+#define CONFIG_SYS_IBAT5L	(CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT5U	(CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
 /* PCI MMIO space: cache-inhibit and guarded */
-#define CFG_IBAT6L	(CFG_PCI1_MMIO_PHYS | BATL_PP_10 | \
+#define CONFIG_SYS_IBAT6L	(CONFIG_SYS_PCI1_MMIO_PHYS | BATL_PP_10 | \
 			BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
-#define CFG_IBAT6U	(CFG_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
-#define CFG_DBAT6L	CFG_IBAT6L
-#define CFG_DBAT6U	CFG_IBAT6U
+#define CONFIG_SYS_IBAT6U	(CONFIG_SYS_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
 #else
-#define CFG_IBAT5L	(0)
-#define CFG_IBAT5U	(0)
-#define CFG_IBAT6L	(0)
-#define CFG_IBAT6U	(0)
-#define CFG_DBAT5L	CFG_IBAT5L
-#define CFG_DBAT5U	CFG_IBAT5U
-#define CFG_DBAT6L	CFG_IBAT6L
-#define CFG_DBAT6U	CFG_IBAT6U
+#define CONFIG_SYS_IBAT5L	(0)
+#define CONFIG_SYS_IBAT5U	(0)
+#define CONFIG_SYS_IBAT6L	(0)
+#define CONFIG_SYS_IBAT6U	(0)
+#define CONFIG_SYS_DBAT5L	CONFIG_SYS_IBAT5L
+#define CONFIG_SYS_DBAT5U	CONFIG_SYS_IBAT5U
+#define CONFIG_SYS_DBAT6L	CONFIG_SYS_IBAT6L
+#define CONFIG_SYS_DBAT6U	CONFIG_SYS_IBAT6U
 #endif
 
 /* Nothing in BAT7 */
-#define CFG_IBAT7L	(0)
-#define CFG_IBAT7U	(0)
-#define CFG_DBAT7L	CFG_IBAT7L
-#define CFG_DBAT7U	CFG_IBAT7U
+#define CONFIG_SYS_IBAT7L	(0)
+#define CONFIG_SYS_IBAT7U	(0)
+#define CONFIG_SYS_DBAT7L	CONFIG_SYS_IBAT7L
+#define CONFIG_SYS_DBAT7U	CONFIG_SYS_IBAT7U
 
 /*
  * Internal Definitions
@@ -553,8 +553,8 @@
 #define CONFIG_HAS_ETH1				/* add support for "eth1addr" */
 #define CONFIG_ETH1ADDR	00:04:9f:ef:03:02
 
-/* use mac_read_from_eeprom() to read ethaddr from I2C EEPROM (see CFG_I2C_EEPROM) */
-#define CFG_I2C_MAC_OFFSET	0x7f00	/* MAC address offset in I2C EEPROM */
+/* use mac_read_from_eeprom() to read ethaddr from I2C EEPROM (see CONFIG_SYS_I2C_EEPROM) */
+#define CONFIG_SYS_I2C_MAC_OFFSET	0x7f00	/* MAC address offset in I2C EEPROM */
 
 #define CONFIG_IPADDR		10.0.0.2
 #define CONFIG_SERVERIP		10.0.0.1