Merge 'next' branch

Conflicts:

	board/freescale/mpc8536ds/mpc8536ds.c
	include/configs/mgcoge.h

Signed-off-by: Wolfgang Denk <wd@denx.de>

1 files changed, 52 insertions, 52 deletions

diff --git a/include/configs/M5271EVB.h b/include/configs/M5271EVB.h
index 844b74f..7ddeb55 100644
--- a/include/configs/M5271EVB.h
+++ b/include/configs/M5271EVB.h
@@ -41,9 +41,9 @@
 #define CONFIG_MCFTMR
 
 #define CONFIG_MCFUART
-#define CFG_UART_PORT		(0)
+#define CONFIG_SYS_UART_PORT		(0)
 #define CONFIG_BAUDRATE		115200
-#define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
 
 #undef CONFIG_WATCHDOG		/* disable watchdog */
 
@@ -57,7 +57,7 @@
 #endif
 #define CONFIG_ENV_SECT_SIZE	0x2000
 #define CONFIG_ENV_IS_IN_FLASH	1
-#define	CFG_USE_PPCENV			/* Environment embedded in sect .ppcenv */
+#define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */
 
 /*
  * BOOTP options
@@ -89,32 +89,32 @@
 #	define CONFIG_NET_MULTI		1
 #	define CONFIG_MII		1
 #	define CONFIG_MII_INIT		1
-#	define CFG_DISCOVER_PHY
-#	define CFG_RX_ETH_BUFFER	8
-#	define CFG_FAULT_ECHO_LINK_DOWN
+#	define CONFIG_SYS_DISCOVER_PHY
+#	define CONFIG_SYS_RX_ETH_BUFFER	8
+#	define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 
-#	define CFG_FEC0_PINMUX		0
-#	define CFG_FEC0_MIIBASE		CFG_FEC0_IOBASE
+#	define CONFIG_SYS_FEC0_PINMUX		0
+#	define CONFIG_SYS_FEC0_MIIBASE		CONFIG_SYS_FEC0_IOBASE
 #	define MCFFEC_TOUT_LOOP		50000
-/* If CFG_DISCOVER_PHY is not defined - hardcoded */
-#	ifndef CFG_DISCOVER_PHY
+/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
+#	ifndef CONFIG_SYS_DISCOVER_PHY
 #		define FECDUPLEX	FULL
 #		define FECSPEED		_100BASET
 #	else
-#		ifndef CFG_FAULT_ECHO_LINK_DOWN
-#			define CFG_FAULT_ECHO_LINK_DOWN
+#		ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
+#			define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
 #		endif
-#	endif			/* CFG_DISCOVER_PHY */
+#	endif			/* CONFIG_SYS_DISCOVER_PHY */
 #endif
 
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hw support */
 #undef CONFIG_SOFT_I2C		/* I2C bit-banged */
-#define CFG_I2C_SPEED		80000
-#define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_OFFSET		0x00000300
-#define CFG_IMMR		CFG_MBAR
+#define CONFIG_SYS_I2C_SPEED		80000
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_OFFSET		0x00000300
+#define CONFIG_SYS_IMMR		CONFIG_SYS_MBAR
 
 #define CONFIG_BOOTDELAY	1	/* autoboot after 5 seconds */
 #define CONFIG_BOOTFILE		"u-boot.bin"
@@ -141,25 +141,25 @@
 	"save\0"				\
 	""
 
-#define CFG_PROMPT		"=> "
-#define CFG_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_PROMPT		"=> "
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
 
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE		1024	/* Console I/O Buffer Size      */
+#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size      */
 #else
-#define CFG_CBSIZE		256	/* Console I/O Buffer Size      */
+#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size      */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
-#define CFG_MAXARGS		16	/* max number of command args   */
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size    */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args   */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */
 
-#define CFG_LOAD_ADDR		0x00100000
+#define CONFIG_SYS_LOAD_ADDR		0x00100000
 
-#define CFG_MEMTEST_START	0x400
-#define CFG_MEMTEST_END		0x380000
+#define CONFIG_SYS_MEMTEST_START	0x400
+#define CONFIG_SYS_MEMTEST_END		0x380000
 
-#define CFG_HZ			1000000
-#define CFG_CLK			100000000
+#define CONFIG_SYS_HZ			1000000
+#define CONFIG_SYS_CLK			100000000
 
 /*
  * Low Level Configuration Settings
@@ -167,56 +167,56 @@
  * You should know what you are doing if you make changes here.
  */
 
-#define CFG_MBAR		0x40000000	/* Register Base Addrs */
+#define CONFIG_SYS_MBAR		0x40000000	/* Register Base Addrs */
 
 /*
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_RAM_ADDR	0x20000000
-#define CFG_INIT_RAM_END	0x1000	/* End of used area in internal SRAM    */
-#define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR	0x20000000
+#define CONFIG_SYS_INIT_RAM_END	0x1000	/* End of used area in internal SRAM    */
+#define CONFIG_SYS_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
-#define CFG_FLASH_BASE		0xffe00000
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_SDRAM_SIZE		16	/* SDRAM size in MB */
+#define CONFIG_SYS_FLASH_BASE		0xffe00000
 
 #ifdef	CONFIG_MONITOR_IS_IN_RAM
-#define CFG_MONITOR_BASE	0x20000
+#define CONFIG_SYS_MONITOR_BASE	0x20000
 #else
-#define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)
 #endif
 
-#define CFG_MONITOR_LEN		0x40000
-#define CFG_MALLOC_LEN		(256 << 10)
-#define CFG_BOOTPARAMS_LEN	(64*1024)
+#define CONFIG_SYS_MONITOR_LEN		0x40000
+#define CONFIG_SYS_MALLOC_LEN		(256 << 10)
+#define CONFIG_SYS_BOOTPARAMS_LEN	(64*1024)
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+#define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
 
 /* FLASH organization */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks           */
-#define CFG_MAX_FLASH_SECT	11	/* max number of sectors on one chip    */
-#define CFG_FLASH_ERASE_TOUT	1000
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks           */
+#define CONFIG_SYS_MAX_FLASH_SECT	11	/* max number of sectors on one chip    */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	1000
 
-#define CFG_FLASH_CFI		1
+#define CONFIG_SYS_FLASH_CFI		1
 #define CONFIG_FLASH_CFI_DRIVER	1
-#define CFG_FLASH_SIZE		0x200000
+#define CONFIG_SYS_FLASH_SIZE		0x200000
 
 /* Cache Configuration */
-#define CFG_CACHELINE_SIZE	16
+#define CONFIG_SYS_CACHELINE_SIZE	16
 
 /* Port configuration */
-#define CFG_FECI2C		0xF0
+#define CONFIG_SYS_FECI2C		0xF0
 
 #endif				/* _M5271EVB_H */