Merge branch 'fixes' into cleanups

Conflicts:

	board/atmel/atngw100/atngw100.c
	board/atmel/atstk1000/atstk1000.c
	cpu/at32ap/at32ap700x/gpio.c
	include/asm-avr32/arch-at32ap700x/clk.h
	include/configs/atngw100.h
	include/configs/atstk1002.h
	include/configs/atstk1003.h
	include/configs/atstk1004.h
	include/configs/atstk1006.h
	include/configs/favr-32-ezkit.h
	include/configs/hammerhead.h
	include/configs/mimc200.h

1 files changed, 85 insertions, 93 deletions

diff --git a/include/configs/M5253DEMO.h b/include/configs/M5253DEMO.h
index 9f78f6e..378e45a 100644
--- a/include/configs/M5253DEMO.h
+++ b/include/configs/M5253DEMO.h
@@ -31,9 +31,9 @@
 #define CONFIG_MCFTMR
 
 #define CONFIG_MCFUART
-#define CFG_UART_PORT		(0)
+#define CONFIG_SYS_UART_PORT		(0)
 #define CONFIG_BAUDRATE		115200
-#define CFG_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600 , 19200 , 38400 , 57600, 115200 }
 
 #undef CONFIG_WATCHDOG		/* disable watchdog */
 
@@ -43,13 +43,13 @@
  * Environment is embedded in u-boot in the second sector of the flash
  */
 #ifdef CONFIG_MONITOR_IS_IN_RAM
-#	define CFG_ENV_OFFSET		0x4000
-#	define CFG_ENV_SECT_SIZE	0x1000
-#	define CFG_ENV_IS_IN_FLASH	1
+#	define CONFIG_ENV_OFFSET		0x4000
+#	define CONFIG_ENV_SECT_SIZE	0x1000
+#	define CONFIG_ENV_IS_IN_FLASH	1
 #else
-#	define CFG_ENV_ADDR		(CFG_FLASH_BASE + 0x4000)
-#	define CFG_ENV_SECT_SIZE	0x1000
-#	define CFG_ENV_IS_IN_FLASH	1
+#	define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE + 0x4000)
+#	define CONFIG_ENV_SECT_SIZE	0x1000
+#	define CONFIG_ENV_IS_IN_FLASH	1
 #endif
 
 /*
@@ -75,22 +75,22 @@
 #	define CONFIG_ATAPI
 #	undef CONFIG_LBA48
 
-#	define CFG_IDE_MAXBUS		1
-#	define CFG_IDE_MAXDEVICE	2
+#	define CONFIG_SYS_IDE_MAXBUS		1
+#	define CONFIG_SYS_IDE_MAXDEVICE	2
 
-#	define CFG_ATA_BASE_ADDR	(CFG_MBAR2 + 0x800)
-#	define CFG_ATA_IDE0_OFFSET	0
+#	define CONFIG_SYS_ATA_BASE_ADDR	(CONFIG_SYS_MBAR2 + 0x800)
+#	define CONFIG_SYS_ATA_IDE0_OFFSET	0
 
-#	define CFG_ATA_DATA_OFFSET	0xA0	/* Offset for data I/O */
-#	define CFG_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
-#	define CFG_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers */
-#	define CFG_ATA_STRIDE		4	/* Interval between registers */
+#	define CONFIG_SYS_ATA_DATA_OFFSET	0xA0	/* Offset for data I/O */
+#	define CONFIG_SYS_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
+#	define CONFIG_SYS_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers */
+#	define CONFIG_SYS_ATA_STRIDE		4	/* Interval between registers */
 #	define _IO_BASE			0
 #endif
 
 #define CONFIG_DRIVER_DM9000
 #ifdef CONFIG_DRIVER_DM9000
-#	define CONFIG_DM9000_BASE	((CFG_CSAR1 << 16) | 0x300)
+#	define CONFIG_DM9000_BASE	(CONFIG_SYS_CS1_BASE | 0x300)
 #	define DM9000_IO		CONFIG_DM9000_BASE
 #	define DM9000_DATA		(CONFIG_DM9000_BASE + 4)
 #	undef CONFIG_DM9000_DEBUG
@@ -104,7 +104,7 @@
 
 #	define CONFIG_EXTRA_ENV_SETTINGS		\
 		"netdev=eth0\0"				\
-		"inpclk=" MK_STR(CFG_INPUT_CLKSRC) "\0"	\
+		"inpclk=" MK_STR(CONFIG_SYS_INPUT_CLKSRC) "\0"	\
 		"loadaddr=10000\0"			\
 		"u-boot=u-boot.bin\0"			\
 		"load=tftp ${loadaddr) ${u-boot}\0"	\
@@ -121,41 +121,41 @@
 /* I2C */
 #define CONFIG_FSL_I2C
 #define CONFIG_HARD_I2C		/* I2C with hw support */
-#define CFG_I2C_SPEED		80000
-#define CFG_I2C_SLAVE		0x7F
-#define CFG_I2C_OFFSET		0x00000280
-#define CFG_IMMR		CFG_MBAR
-#define CFG_I2C_PINMUX_REG	(*(u32 *) (CFG_MBAR+0x19C))
-#define CFG_I2C_PINMUX_CLR	(0xFFFFE7FF)
-#define CFG_I2C_PINMUX_SET	(0)
+#define CONFIG_SYS_I2C_SPEED		80000
+#define CONFIG_SYS_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_OFFSET		0x00000280
+#define CONFIG_SYS_IMMR		CONFIG_SYS_MBAR
+#define CONFIG_SYS_I2C_PINMUX_REG	(*(u32 *) (CONFIG_SYS_MBAR+0x19C))
+#define CONFIG_SYS_I2C_PINMUX_CLR	(0xFFFFE7FF)
+#define CONFIG_SYS_I2C_PINMUX_SET	(0)
 
-#define CFG_PROMPT		"=> "
-#define CFG_LONGHELP		/* undef to save memory */
+#define CONFIG_SYS_PROMPT		"=> "
+#define CONFIG_SYS_LONGHELP		/* undef to save memory */
 
 #if defined(CONFIG_CMD_KGDB)
-#	define CFG_CBSIZE		1024	/* Console I/O Buffer Size */
+#	define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size */
 #else
-#	define CFG_CBSIZE		256	/* Console I/O Buffer Size */
+#	define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size */
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size */
-#define CFG_MAXARGS		16	/* max number of command args */
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS		16	/* max number of command args */
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size */
 
-#define CFG_LOAD_ADDR		0x00100000
+#define CONFIG_SYS_LOAD_ADDR		0x00100000
 
-#define CFG_MEMTEST_START	0x400
-#define CFG_MEMTEST_END		0x380000
+#define CONFIG_SYS_MEMTEST_START	0x400
+#define CONFIG_SYS_MEMTEST_END		0x380000
 
-#define CFG_HZ			1000
+#define CONFIG_SYS_HZ			1000
 
-#undef CFG_PLL_BYPASS		/* bypass PLL for test purpose */
-#define CFG_FAST_CLK
-#ifdef CFG_FAST_CLK
-#	define CFG_PLLCR	0x1243E054
-#	define CFG_CLK		140000000
+#undef CONFIG_SYS_PLL_BYPASS		/* bypass PLL for test purpose */
+#define CONFIG_SYS_FAST_CLK
+#ifdef CONFIG_SYS_FAST_CLK
+#	define CONFIG_SYS_PLLCR	0x1243E054
+#	define CONFIG_SYS_CLK		140000000
 #else
-#	define CFG_PLLCR	0x135a4140
-#	define CFG_CLK		70000000
+#	define CONFIG_SYS_PLLCR	0x135a4140
+#	define CONFIG_SYS_CLK		70000000
 #endif
 
 /*
@@ -164,100 +164,92 @@
  * You should know what you are doing if you make changes here.
  */
 
-#define CFG_MBAR		0x10000000	/* Register Base Addrs */
-#define CFG_MBAR2		0x80000000	/* Module Base Addrs 2 */
+#define CONFIG_SYS_MBAR		0x10000000	/* Register Base Addrs */
+#define CONFIG_SYS_MBAR2		0x80000000	/* Module Base Addrs 2 */
 
 /*
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_RAM_ADDR	0x20000000
-#define CFG_INIT_RAM_END	0x10000	/* End of used area in internal SRAM */
-#define CFG_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR	0x20000000
+#define CONFIG_SYS_INIT_RAM_END	0x10000	/* End of used area in internal SRAM */
+#define CONFIG_SYS_GBL_DATA_SIZE	128	/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_SDRAM_SIZE		16	/* SDRAM size in MB */
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_SDRAM_SIZE		16	/* SDRAM size in MB */
 
 #ifdef CONFIG_MONITOR_IS_IN_RAM
-#	define CFG_MONITOR_BASE	0x20000
+#	define CONFIG_SYS_MONITOR_BASE	0x20000
 #else
-#	define CFG_MONITOR_BASE	(CFG_FLASH_BASE + 0x400)
+#	define CONFIG_SYS_MONITOR_BASE	(CONFIG_SYS_FLASH_BASE + 0x400)
 #endif
 
-#define CFG_MONITOR_LEN		0x40000
-#define CFG_MALLOC_LEN		(256 << 10)
-#define CFG_BOOTPARAMS_LEN	(64*1024)
+#define CONFIG_SYS_MONITOR_LEN		0x40000
+#define CONFIG_SYS_MALLOC_LEN		(256 << 10)
+#define CONFIG_SYS_BOOTPARAMS_LEN	(64*1024)
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization ??
  */
-#define CFG_BOOTMAPSZ		(CFG_SDRAM_BASE + (CFG_SDRAM_SIZE << 20))
+#define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
 
 /* FLASH organization */
-#define CFG_FLASH_BASE		(CFG_CSAR0 << 16)
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks */
-#define CFG_MAX_FLASH_SECT	2048	/* max number of sectors on one chip */
-#define CFG_FLASH_ERASE_TOUT	1000
+#define CONFIG_SYS_FLASH_BASE		(CONFIG_SYS_CS0_BASE)
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
+#define CONFIG_SYS_MAX_FLASH_SECT	2048	/* max number of sectors on one chip */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	1000
 
 #define FLASH_SST6401B		0x200
 #define SST_ID_xF6401B		0x236D236D
 
-#undef CFG_FLASH_CFI
-#ifdef CFG_FLASH_CFI
+#undef CONFIG_SYS_FLASH_CFI
+#ifdef CONFIG_SYS_FLASH_CFI
 /*
  * Unable to use CFI driver, due to incompatible sector erase command by SST.
  * Amd/Atmel use 0x30 for sector erase, SST use 0x50.
  * 0x30 is block erase in SST
  */
 #	define CONFIG_FLASH_CFI_DRIVER	1
-#	define CFG_FLASH_SIZE		0x800000
-#	define CFG_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
+#	define CONFIG_SYS_FLASH_SIZE		0x800000
+#	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
 #	define CONFIG_FLASH_CFI_LEGACY
 #else
-#	define CFG_SST_SECT		2048
-#	define CFG_SST_SECTSZ		0x1000
-#	define CFG_FLASH_WRITE_TOUT	500
+#	define CONFIG_SYS_SST_SECT		2048
+#	define CONFIG_SYS_SST_SECTSZ		0x1000
+#	define CONFIG_SYS_FLASH_WRITE_TOUT	500
 #endif
 
 /* Cache Configuration */
-#define CFG_CACHELINE_SIZE	16
+#define CONFIG_SYS_CACHELINE_SIZE	16
 
 /* Port configuration */
-#define CFG_FECI2C		0xF0
+#define CONFIG_SYS_FECI2C		0xF0
 
-#define CFG_CSAR0		0xFF80
-#define CFG_CSMR0		0x007F0021
-#define CFG_CSCR0		0x1D80
+#define CONFIG_SYS_CS0_BASE		0xFF800000
+#define CONFIG_SYS_CS0_MASK		0x007F0021
+#define CONFIG_SYS_CS0_CTRL		0x00001D80
 
-#define CFG_CSAR1               0xE000
-#define CFG_CSMR1               0x00000001
-#define CFG_CSCR1               0x3DD8
-
-#define CFG_CSAR2		0
-#define CFG_CSMR2		0
-#define CFG_CSCR2		0
-
-#define CFG_CSAR3		0
-#define CFG_CSMR3		0
-#define CFG_CSCR3		0
+#define CONFIG_SYS_CS1_BASE		0xE0000000
+#define CONFIG_SYS_CS1_MASK		0x00000001
+#define CONFIG_SYS_CS1_CTRL		0x00003DD8
 
 /*-----------------------------------------------------------------------
  * Port configuration
  */
-#define CFG_GPIO_FUNC		0x00000008	/* Set gpio pins: none */
-#define CFG_GPIO1_FUNC		0x00df00f0	/* 36-39(SWITCH),48-52(FPGAs),54 */
-#define CFG_GPIO_EN		0x00000008	/* Set gpio output enable */
-#define CFG_GPIO1_EN		0x00c70000	/* Set gpio output enable */
-#define CFG_GPIO_OUT		0x00000008	/* Set outputs to default state */
-#define CFG_GPIO1_OUT		0x00c70000	/* Set outputs to default state */
-#define CFG_GPIO1_LED		0x00400000	/* user led */
+#define CONFIG_SYS_GPIO_FUNC		0x00000008	/* Set gpio pins: none */
+#define CONFIG_SYS_GPIO1_FUNC		0x00df00f0	/* 36-39(SWITCH),48-52(FPGAs),54 */
+#define CONFIG_SYS_GPIO_EN		0x00000008	/* Set gpio output enable */
+#define CONFIG_SYS_GPIO1_EN		0x00c70000	/* Set gpio output enable */
+#define CONFIG_SYS_GPIO_OUT		0x00000008	/* Set outputs to default state */
+#define CONFIG_SYS_GPIO1_OUT		0x00c70000	/* Set outputs to default state */
+#define CONFIG_SYS_GPIO1_LED		0x00400000	/* user led */
 
 #endif				/* _M5253DEMO_H */