rename CFG_ macros to CONFIG_SYS

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

1 files changed, 82 insertions, 82 deletions

diff --git a/include/configs/KUP4X.h b/include/configs/KUP4X.h
index a71be0f..be6dfda 100644
--- a/include/configs/KUP4X.h
+++ b/include/configs/KUP4X.h
@@ -50,11 +50,11 @@
 
 #define CONFIG_BOARD_TYPES	1	/* support board types			*/
 
-#define CFG_8XX_FACT		8	/* Multiply by 8			*/
-#define CFG_8XX_XIN		16000000	/* 16 MHz in			*/
+#define CONFIG_SYS_8XX_FACT		8	/* Multiply by 8			*/
+#define CONFIG_SYS_8XX_XIN		16000000	/* 16 MHz in			*/
 
 
-#define MPC8XX_HZ ((CFG_8XX_XIN) * (CFG_8XX_FACT))
+#define MPC8XX_HZ ((CONFIG_SYS_8XX_XIN) * (CONFIG_SYS_8XX_FACT))
 
 /* should ALWAYS define this, measure_gclk in speed.c is unreliable */
 /* in general, we always know this for FADS+new ADS anyway */
@@ -91,7 +91,7 @@
 #define CONFIG_MISC_INIT_F	1
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
 
 #define	CONFIG_WATCHDOG		1	/* watchdog enabled		*/
 
@@ -118,8 +118,8 @@
 #undef	CONFIG_HARD_I2C			/* I2C with hardware support	*/
 #define	CONFIG_SOFT_I2C         1	/* I2C bit-banged		*/
 
-#define CFG_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
-#define CFG_I2C_SLAVE		0xFE
+#define CONFIG_SYS_I2C_SPEED		93000	/* 93 kHz is supposed to work	*/
+#define CONFIG_SYS_I2C_SLAVE		0xFE
 
 #ifdef CONFIG_SOFT_I2C
 /*
@@ -144,20 +144,20 @@
  * I2C Configuration
  */
 
-#define CFG_I2C_PICIO_ADDR	0x21	/* PCF8574 IO Expander			*/
-#define CFG_I2C_RTC_ADDR	0x51	/* PCF8563 RTC				*/
+#define CONFIG_SYS_I2C_PICIO_ADDR	0x21	/* PCF8574 IO Expander			*/
+#define CONFIG_SYS_I2C_RTC_ADDR	0x51	/* PCF8563 RTC				*/
 
 
 /* List of I2C addresses to be verified by POST */
 
-#define I2C_ADDR_LIST	{CFG_I2C_PICIO_ADDR,	\
-			CFG_I2C_RTC_ADDR,	\
+#define I2C_ADDR_LIST	{CONFIG_SYS_I2C_PICIO_ADDR,	\
+			CONFIG_SYS_I2C_RTC_ADDR,	\
 			}
 
 
 #define CONFIG_RTC_PCF8563		/* use Philips PCF8563 RTC	*/
 
-#define CFG_DISCOVER_PHY
+#define CONFIG_SYS_DISCOVER_PHY
 #define CONFIG_MII
 
 #if 0
@@ -172,9 +172,9 @@
 #if 1
 /* POST support */
 
-#define CONFIG_POST		(CFG_POST_CPU	   | \
-				 CFG_POST_RTC	   | \
-				 CFG_POST_I2C)
+#define CONFIG_POST		(CONFIG_SYS_POST_CPU	   | \
+				 CONFIG_SYS_POST_RTC	   | \
+				 CONFIG_SYS_POST_I2C)
 #endif
 
 
@@ -199,26 +199,26 @@
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_MEMTEST_START	0x000400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x003C00000	/* 4 ... 60 MB in DRAM	*/
-#define CFG_LOAD_ADDR		0x200000	/* default load address */
+#define CONFIG_SYS_MEMTEST_START	0x000400000	/* memtest works on	*/
+#define CONFIG_SYS_MEMTEST_END		0x003C00000	/* 4 ... 60 MB in DRAM	*/
+#define CONFIG_SYS_LOAD_ADDR		0x200000	/* default load address */
 
-#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */
 
-#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 115200 }
 
-#define CFG_CONSOLE_INFO_QUIET 1
+#define CONFIG_SYS_CONSOLE_INFO_QUIET 1
 
 /*
  * Low Level Configuration Settings
@@ -228,43 +228,43 @@
 /*-----------------------------------------------------------------------
  * Internal Memory Mapped Register
  */
-#define CFG_IMMR		0xFFF00000
+#define CONFIG_SYS_IMMR		0xFFF00000
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_RAM_ADDR	CFG_IMMR
-#define CFG_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
-#define CFG_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
+#define CONFIG_SYS_GBL_DATA_SIZE	64	/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_FLASH_BASE		0x40000000
-#define CFG_MONITOR_LEN		(192 << 10)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MONITOR_BASE	CFG_FLASH_BASE
-#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		0x40000000
+#define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 256 kB for Monitor	*/
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	19	/* max number of sectors on one chip	*/
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CONFIG_SYS_MAX_FLASH_SECT	19	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
 #define CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_OFFSET		0x40000 /*   Offset   of Environment Sector	*/
@@ -280,16 +280,16 @@
  * Hardware Information Block
  */
 #if 1
-#define CFG_HWINFO_OFFSET	0x000F0000	/* offset of HW Info block */
-#define CFG_HWINFO_SIZE		0x00000100	/* size   of HW Info block */
-#define CFG_HWINFO_MAGIC	0x4B26500D	/* 'K&P<CR>' */
+#define CONFIG_SYS_HWINFO_OFFSET	0x000F0000	/* offset of HW Info block */
+#define CONFIG_SYS_HWINFO_SIZE		0x00000100	/* size   of HW Info block */
+#define CONFIG_SYS_HWINFO_MAGIC	0x4B26500D	/* 'K&P<CR>' */
 #endif
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
+#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
+#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
 #endif
 
 /*-----------------------------------------------------------------------
@@ -299,10 +299,10 @@
  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
  */
 #if 0 && defined(CONFIG_WATCHDOG)       /* KUP uses external TPS3705 WD */
-#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 #else
-#define CFG_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
 #endif
 
 /*-----------------------------------------------------------------------
@@ -310,14 +310,14 @@
  *-----------------------------------------------------------------------
  * PCMCIA config., multi-function pin tri-state
  */
-#define CFG_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC00)
+#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC00)
 
 /*-----------------------------------------------------------------------
  * TBSCR - Time Base Status and Control				11-26
  *-----------------------------------------------------------------------
  * Clear Reference Interrupt Status, Timebase freezing enabled
  */
-#define CFG_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
+#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
 
 
 /*-----------------------------------------------------------------------
@@ -325,7 +325,7 @@
  *-----------------------------------------------------------------------
  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
  */
-#define CFG_PISCR	(PISCR_PS | PISCR_PITF)
+#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)
 
 
 /*-----------------------------------------------------------------------
@@ -333,7 +333,7 @@
  *-----------------------------------------------------------------------
  * set the PLL, the low-power modes and the reset control (15-29)
  */
-#define CFG_PLPRCR	((CFG_8XX_FACT << PLPRCR_MFI_SHIFT) |	\
+#define CONFIG_SYS_PLPRCR	((CONFIG_SYS_8XX_FACT << PLPRCR_MFI_SHIFT) |	\
 				PLPRCR_SPLSS | PLPRCR_TEXPS)
 
 
@@ -344,7 +344,7 @@
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF00
-#define CFG_SCCR	(SCCR_TBS | SCCR_EBDF01 |  \
+#define CONFIG_SYS_SCCR	(SCCR_TBS | SCCR_EBDF01 |  \
 			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)
@@ -358,14 +358,14 @@
 /* KUP4K use both slots, SLOT_A as "primary". */
 #define CONFIG_PCMCIA_SLOT_A 1
 
-#define CFG_PCMCIA_MEM_ADDR	(0xE0000000)
-#define CFG_PCMCIA_MEM_SIZE	( 64 << 20 )
-#define CFG_PCMCIA_DMA_ADDR	(0xE4000000)
-#define CFG_PCMCIA_DMA_SIZE	( 64 << 20 )
-#define CFG_PCMCIA_ATTRB_ADDR	(0xE8000000)
-#define CFG_PCMCIA_ATTRB_SIZE	( 64 << 20 )
-#define CFG_PCMCIA_IO_ADDR	(0xEC000000)
-#define CFG_PCMCIA_IO_SIZE	( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
+#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
+#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
+#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
+#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
+#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )
 
 #define PCMCIA_SOCKETS_NO 1
 #define PCMCIA_MEM_WIN_NO 8
@@ -380,23 +380,23 @@
 #define CONFIG_IDE_LED			1   /* LED   for ide supported	*/
 #undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/
 
-#define CFG_IDE_MAXBUS		1
-#define CFG_IDE_MAXDEVICE	2
+#define CONFIG_SYS_IDE_MAXBUS		1
+#define CONFIG_SYS_IDE_MAXDEVICE	2
 
-#define CFG_ATA_IDE0_OFFSET	0x0000
+#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000
 
-#define CFG_ATA_IDE1_OFFSET	(4 * CFG_PCMCIA_MEM_SIZE)
+#define CONFIG_SYS_ATA_IDE1_OFFSET	(4 * CONFIG_SYS_PCMCIA_MEM_SIZE)
 
-#define CFG_ATA_BASE_ADDR	CFG_PCMCIA_MEM_ADDR
+#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR
 
 /* Offset for data I/O			*/
-#define CFG_ATA_DATA_OFFSET	(CFG_PCMCIA_MEM_SIZE + 0x320)
+#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 
 /* Offset for normal register accesses	*/
-#define CFG_ATA_REG_OFFSET	(2 * CFG_PCMCIA_MEM_SIZE + 0x320)
+#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
 
 /* Offset for alternate registers	*/
-#define CFG_ATA_ALT_OFFSET	0x0100
+#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100
 
 
 /*-----------------------------------------------------------------------
@@ -404,7 +404,7 @@
  *-----------------------------------------------------------------------
  *
  */
-#define CFG_DER 0
+#define CONFIG_SYS_DER 0
 
 /*
  * Init Memory Controller:
@@ -417,30 +417,30 @@
  * restrict access enough to keep SRAM working (if any)
  * but not too much to meddle with FLASH accesses
  */
-#define CFG_REMAP_OR_AM		0x80000000	/* OR addr mask */
-#define CFG_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
+#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
+#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */
 
 /*
  * FLASH timing:
  */
-#define CFG_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
+#define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_2_CLK | OR_EHTR | OR_BI)
 
-#define CFG_OR0_REMAP	(CFG_REMAP_OR_AM  | CFG_OR_TIMING_FLASH)
-#define CFG_OR0_PRELIM	(CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH)
-#define CFG_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
+#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
+#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
 
 
 /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
-#define CFG_OR_TIMING_SDRAM	0x00000A00
+#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00
 
 
-#define CFG_MPTPR 0x400
+#define CONFIG_SYS_MPTPR 0x400
 
 /*
  * MAMR settings for SDRAM
  */
-#define CFG_MAMR 0x80802114
+#define CONFIG_SYS_MAMR 0x80802114
 
 
 /*