Merge 'next' branch

Conflicts:

	board/freescale/mpc8536ds/mpc8536ds.c
	include/configs/mgcoge.h

Signed-off-by: Wolfgang Denk <wd@denx.de>

1 files changed, 66 insertions, 66 deletions

diff --git a/include/configs/JSE.h b/include/configs/JSE.h
index b457272..508b5c8 100644
--- a/include/configs/JSE.h
+++ b/include/configs/JSE.h
@@ -41,28 +41,28 @@
   /* ... with a 33MHz OSC. connected to the SysCLK input */
 #define CONFIG_SYS_CLK_FREQ	33333333
   /* ... with on-chip memory here (4KBytes) */
-#define CFG_OCM_DATA_ADDR 0xF4000000
-#define CFG_OCM_DATA_SIZE 0x00001000
+#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000
+#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000
   /* Do not set up locked dcache as init ram. */
-#undef CFG_INIT_DCACHE_CS
+#undef CONFIG_SYS_INIT_DCACHE_CS
 
   /* Map the SystemACE chip (CS#1) here. (Must be a multiple of 1Meg) */
 #define CONFIG_SYSTEMACE 1
-#define CFG_SYSTEMACE_BASE 0xf0000000
-#define CFG_SYSTEMACE_WIDTH 8
+#define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
+#define CONFIG_SYS_SYSTEMACE_WIDTH 8
 #define CONFIG_DOS_PARTITION 1
 
   /* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */
-#define CFG_TEMP_STACK_OCM 1
+#define CONFIG_SYS_TEMP_STACK_OCM 1
   /* ... place INIT RAM in the OCM address */
-# define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR
+# define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR
   /* ... give it the whole init ram */
-# define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE
+# define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE
   /* ... Shave a bit off the end for global data */
-# define CFG_GBL_DATA_SIZE	128
-# define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+# define CONFIG_SYS_GBL_DATA_SIZE	128
+# define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
   /* ... and place the stack pointer at the top of what's left. */
-# define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+# define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
   /* Enable board_pre_init function */
 #define CONFIG_BOARD_PRE_INIT	1
@@ -72,7 +72,7 @@
   /* Disable call to post_init_f: late init function. */
 #undef CONFIG_POST
   /* Enable DRAM test. */
-#define CFG_DRAM_TEST 1
+#define CONFIG_SYS_DRAM_TEST 1
   /* Enable misc_init_r function. */
 #define CONFIG_MISC_INIT_R 1
 
@@ -83,14 +83,14 @@
 #undef	CONFIG_ENV_IS_NOWHERE
 
   /* This is the 7bit address of the device, not including P. */
-#define CFG_I2C_EEPROM_ADDR 0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
   /* After the device address, need one more address byte. */
-#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
   /* The EEPROM is 512 bytes. */
-#define CFG_EEPROM_SIZE 512
+#define CONFIG_SYS_EEPROM_SIZE 512
   /* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
-#define CFG_EEPROM_PAGE_WRITE_BITS 4
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
   /* Put the environment in the second half. */
 #define CONFIG_ENV_OFFSET	0x00
 #define CONFIG_ENV_SIZE	512
@@ -130,7 +130,7 @@
 
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
+#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
 #define CONFIG_PHY_ADDR		1	/* PHY address			*/
@@ -171,52 +171,52 @@
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP			/* undef to save memory		*/
-#define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#define CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 
-#define CFG_HUSH_PARSER			/* use "hush" command parser	*/
-#ifdef	CFG_HUSH_PARSER
-#define CFG_PROMPT_HUSH_PS2	"> "
+#define CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/
+#ifdef	CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if defined(CONFIG_CMD_KGDB)
-#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
+#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
 /*
- * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
+ * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
  * The Linux BASE_BAUD define should match this configuration.
  *    baseBaud = cpuClock/(uartDivisor*16)
- * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
  * set Linux BASE_BAUD to 403200.
  */
-#undef	CFG_EXT_SERIAL_CLOCK	       /* external serial clock */
-#undef	CFG_405_UART_ERRATA_59	       /* 405GP/CR Rev. D silicon */
-#define CFG_BASE_BAUD	    691200
+#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* external serial clock */
+#undef	CONFIG_SYS_405_UART_ERRATA_59	       /* 405GP/CR Rev. D silicon */
+#define CONFIG_SYS_BASE_BAUD	    691200
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE  \
+#define CONFIG_SYS_BAUDRATE_TABLE  \
     {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
 
-#define CFG_LOAD_ADDR		0x100000	/* default load address */
-#define CFG_EXTBDINFO		1	/* To use extended board_into (bd_t) */
+#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
+#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
 
-#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
 #undef	CONFIG_SOFT_I2C			/* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_SLAVE		0x7F
 
 
 /*-----------------------------------------------------------------------
@@ -232,14 +232,14 @@
 #undef	CONFIG_PCI_PNP			/* do pci plug-and-play		*/
 					/* resource configuration	*/
 
-#define CFG_PCI_SUBSYS_VENDORID 0x0000	/* PCI Vendor ID: to-do!!!	*/
-#define CFG_PCI_SUBSYS_DEVICEID 0x0000	/* PCI Device ID: to-do!!!	*/
-#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
-#define CFG_PCI_PTM1MS	0x80000001	/* 2GB, enable hard-wired to 1	*/
-#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
-#define CFG_PCI_PTM2LA	0x00000000	/* disabled			*/
-#define CFG_PCI_PTM2MS	0x00000000	/* disabled			*/
-#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
+#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000	/* PCI Vendor ID: to-do!!!	*/
+#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000	/* PCI Device ID: to-do!!!	*/
+#define CONFIG_SYS_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CONFIG_SYS_PCI_PTM1MS	0x80000001	/* 2GB, enable hard-wired to 1	*/
+#define CONFIG_SYS_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CONFIG_SYS_PCI_PTM2LA	0x00000000	/* disabled			*/
+#define CONFIG_SYS_PCI_PTM2MS	0x00000000	/* disabled			*/
+#define CONFIG_SYS_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * External peripheral base address
@@ -248,36 +248,36 @@
 #undef	CONFIG_IDE_LED			/* no led for ide supported	*/
 #undef	CONFIG_IDE_RESET		/* no reset for ide supported	*/
 
-#define CFG_KEY_REG_BASE_ADDR	0xF0100000
-#define CFG_IR_REG_BASE_ADDR	0xF0200000
-#define CFG_FPGA_REG_BASE_ADDR	0xF0300000
+#define CONFIG_SYS_KEY_REG_BASE_ADDR	0xF0100000
+#define CONFIG_SYS_IR_REG_BASE_ADDR	0xF0200000
+#define CONFIG_SYS_FPGA_REG_BASE_ADDR	0xF0300000
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_FLASH_BASE		0xFFF80000
-#define CFG_MONITOR_BASE	CFG_FLASH_BASE
-#define CFG_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CFG_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		0xFFF80000
+#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
+#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
+#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
 /*
  * Init Memory Controller:
@@ -285,7 +285,7 @@
  * BR0/1 and OR0/1 (FLASH)
  */
 
-#define FLASH_BASE0_PRELIM	CFG_FLASH_BASE	/* FLASH bank #0	*/
+#define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0	*/
 #define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/