Merge branch 'master' of /home/stefan/git/u-boot/u-boot

1 files changed, 101 insertions, 101 deletions

diff --git a/include/configs/IDS8247.h b/include/configs/IDS8247.h
index 4d0397c..a610ac9 100644
--- a/include/configs/IDS8247.h
+++ b/include/configs/IDS8247.h
@@ -73,8 +73,8 @@
 /* enable I2C and select the hardware/software driver */
 #undef  CONFIG_HARD_I2C			/* I2C with hardware support	*/
 #define CONFIG_SOFT_I2C		1	/* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000	/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_SLAVE		0x7F
 
 /*
  * Software (bit-bang) I2C driver configuration
@@ -91,10 +91,10 @@
 #define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */
 
 #if 0
-#define CFG_I2C_EEPROM_ADDR	0x50
-#define CFG_I2C_EEPROM_ADDR_LEN 2
-#define CFG_EEPROM_PAGE_WRITE_BITS	4
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x50
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
 
 #define CONFIG_I2C_X
 #endif
@@ -108,17 +108,17 @@
 /*
  * NS16550 Configuration
  */
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
 
-#define CFG_NS16550_REG_SIZE    1
+#define CONFIG_SYS_NS16550_REG_SIZE    1
 
-#define CFG_NS16550_CLK         14745600
+#define CONFIG_SYS_NS16550_CLK         14745600
 
-#define	CFG_UART_BASE	0xE0000000
-#define CFG_UART_SIZE	0x10000
+#define	CONFIG_SYS_UART_BASE	0xE0000000
+#define CONFIG_SYS_UART_SIZE	0x10000
 
-#define CFG_NS16550_COM1        (CFG_UART_BASE + 0x8000)
+#define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_UART_BASE + 0x8000)
 
 
 /* pass open firmware flat tree */
@@ -154,17 +154,17 @@
  * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
  * - Enable Full Duplex in FSMR
  */
-# define CFG_CMXFCR_MASK	(CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
-# define CFG_CMXFCR_VALUE	(CMXFCR_RF1CS_CLK10|CMXFCR_TF1CS_CLK9)
-# define CFG_CPMFCR_RAMTYPE	0
-# define CFG_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
+# define CONFIG_SYS_CMXFCR_MASK	(CMXFCR_FC1|CMXFCR_RF1CS_MSK|CMXFCR_TF1CS_MSK)
+# define CONFIG_SYS_CMXFCR_VALUE	(CMXFCR_RF1CS_CLK10|CMXFCR_TF1CS_CLK9)
+# define CONFIG_SYS_CPMFCR_RAMTYPE	0
+# define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB)
 
 
 /* system clock rate (CLKIN) - equal to the 60x and local bus speed */
 #define CONFIG_8260_CLKIN	66666666	/* in Hz */
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#undef	CFG_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
+#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/
 
 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -180,7 +180,7 @@
 #define CONFIG_BOOTP_BOOTFILESIZE
 
 #define CONFIG_RTC_PCF8563
-#define CFG_I2C_RTC_ADDR		0x51
+#define CONFIG_SYS_I2C_RTC_ADDR		0x51
 
 /*
  * Command line configuration.
@@ -197,62 +197,62 @@
 /*
  * Miscellaneous configurable options
  */
-#define	CFG_LONGHELP			/* undef to save memory		*/
-#define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
+#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
+#define	CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if defined(CONFIG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
-#define	CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
-#define	CFG_MAXARGS	16		/* max number of command args	*/
-#define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
+#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CFG_MEMTEST_END	0x0C00000	/* 4 ... 12 MB in DRAM	*/
+#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
+#define CONFIG_SYS_MEMTEST_END	0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define	CFG_LOAD_ADDR	0x100000	/* default load address	*/
+#define	CONFIG_SYS_LOAD_ADDR	0x100000	/* default load address	*/
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define	CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks	*/
 
-#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
 
-#define	CFG_RESET_ADDRESS 0xFDFFFFFC	/* "bad" address		*/
+#define	CONFIG_SYS_RESET_ADDRESS 0xFDFFFFFC	/* "bad" address		*/
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ        (8 << 20)       /* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ        (8 << 20)       /* Initial Memory map for Linux */
 
-#define CFG_FLASH_CFI				/* The flash is CFI compatible  */
+#define CONFIG_SYS_FLASH_CFI				/* The flash is CFI compatible  */
 #define CONFIG_FLASH_CFI_DRIVER			/* Use common CFI driver        */
-#define CFG_FLASH_BANKS_LIST	{ 0xFF800000 }
-#define CFG_MAX_FLASH_BANKS_DETECT	1
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ 0xFF800000 }
+#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT	1
 /* What should the base address of the main FLASH be and how big is
  * it (in MBytes)? This must contain TEXT_BASE from board/ids8247/config.mk
  * The main FLASH is whichever is connected to *CS0.
  */
-#define CFG_FLASH0_BASE 0xFFF00000
-#define CFG_FLASH0_SIZE 8
+#define CONFIG_SYS_FLASH0_BASE 0xFFF00000
+#define CONFIG_SYS_FLASH0_SIZE 8
 
 /* Flash bank size (for preliminary settings)
  */
-#define CFG_FLASH_SIZE CFG_FLASH0_SIZE
+#define CONFIG_SYS_FLASH_SIZE CONFIG_SYS_FLASH0_SIZE
 
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max num of memory banks      */
-#define CFG_MAX_FLASH_SECT	128	/* max num of sects on one chip */
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */
+#define CONFIG_SYS_MAX_FLASH_SECT	128	/* max num of sects on one chip */
 
-#define CFG_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
-#define CFG_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
+#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
 
 /* Environment in flash */
 #define CONFIG_ENV_IS_IN_FLASH	1
-#define CONFIG_ENV_ADDR		(CFG_FLASH_BASE+0x60000)
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+0x60000)
 #define CONFIG_ENV_SIZE		0x20000
 #define CONFIG_ENV_SECT_SIZE	0x20000
 
@@ -263,9 +263,9 @@
 #if defined(CONFIG_CMD_NAND)
 
 #define CONFIG_NAND_LEGACY
-#define CFG_NAND0_BASE 0xE1000000
+#define CONFIG_SYS_NAND0_BASE 0xE1000000
 
-#define CFG_MAX_NAND_DEVICE     1       /* Max number of NAND devices           */
+#define CONFIG_SYS_MAX_NAND_DEVICE     1       /* Max number of NAND devices           */
 #define SECTORSIZE 512
 #define NAND_NO_RB
 
@@ -326,47 +326,47 @@
 /*-----------------------------------------------------------------------
  * Hard Reset Configuration Words
  *
- * if you change bits in the HRCW, you must also change the CFG_*
+ * if you change bits in the HRCW, you must also change the CONFIG_SYS_*
  * defines for the various registers affected by the HRCW e.g. changing
- * HRCW_DPPCxx requires you to also change CFG_SIUMCR.
+ * HRCW_DPPCxx requires you to also change CONFIG_SYS_SIUMCR.
  */
-#define CFG_HRCW_MASTER	(HRCW_BPS01 | HRCW_BMS | HRCW_ISB100 | HRCW_APPC10 | HRCW_MODCK_H1000)
+#define CONFIG_SYS_HRCW_MASTER	(HRCW_BPS01 | HRCW_BMS | HRCW_ISB100 | HRCW_APPC10 | HRCW_MODCK_H1000)
 
 /* no slaves so just fill with zeros */
-#define CFG_HRCW_SLAVE1		0
-#define CFG_HRCW_SLAVE2		0
-#define CFG_HRCW_SLAVE3		0
-#define CFG_HRCW_SLAVE4		0
-#define CFG_HRCW_SLAVE5		0
-#define CFG_HRCW_SLAVE6		0
-#define CFG_HRCW_SLAVE7		0
+#define CONFIG_SYS_HRCW_SLAVE1		0
+#define CONFIG_SYS_HRCW_SLAVE2		0
+#define CONFIG_SYS_HRCW_SLAVE3		0
+#define CONFIG_SYS_HRCW_SLAVE4		0
+#define CONFIG_SYS_HRCW_SLAVE5		0
+#define CONFIG_SYS_HRCW_SLAVE6		0
+#define CONFIG_SYS_HRCW_SLAVE7		0
 
 /*-----------------------------------------------------------------------
  * Internal Memory Mapped Register
  */
-#define CFG_IMMR		0xF0000000
+#define CONFIG_SYS_IMMR		0xF0000000
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_RAM_ADDR	CFG_IMMR
-#define CFG_INIT_RAM_END	0x2000  /* End of used area in DPRAM    */
-#define CFG_GBL_DATA_SIZE	128 /* size in bytes reserved for initial data*/
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
+#define CONFIG_SYS_INIT_RAM_END	0x2000  /* End of used area in DPRAM    */
+#define CONFIG_SYS_GBL_DATA_SIZE	128 /* size in bytes reserved for initial data*/
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  *
- * 60x SDRAM is mapped at CFG_SDRAM_BASE
+ * 60x SDRAM is mapped at CONFIG_SYS_SDRAM_BASE
  */
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_FLASH_BASE		CFG_FLASH0_BASE
-#define CFG_MONITOR_BASE	TEXT_BASE
-#define CFG_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
-#define CFG_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()*/
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_FLASH0_BASE
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
+#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */
+#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()*/
 
 /*
  * Internal Definitions
@@ -380,9 +380,9 @@
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_CACHELINE_SIZE      32      /* For MPC8260 CPU              */
+#define CONFIG_SYS_CACHELINE_SIZE      32      /* For MPC8260 CPU              */
 #if defined(CONFIG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+# define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
 /*-----------------------------------------------------------------------
@@ -396,28 +396,28 @@
  * HID1 has only read-only information - nothing to set.
  */
 
-#define CFG_HID0_INIT   (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI)
-#define CFG_HID0_FINAL  0
-#define CFG_HID2        0
+#define CONFIG_SYS_HID0_INIT   (HID0_ICE|HID0_DCE|HID0_ICFI|HID0_DCI)
+#define CONFIG_SYS_HID0_FINAL  0
+#define CONFIG_SYS_HID2        0
 
 /*-----------------------------------------------------------------------
  * RMR - Reset Mode Register                                     5-5
  *-----------------------------------------------------------------------
  * turn on Checkstop Reset Enable
  */
-#define CFG_RMR         0
+#define CONFIG_SYS_RMR         0
 
 /*-----------------------------------------------------------------------
  * BCR - Bus Configuration                                       4-25
  *-----------------------------------------------------------------------
  */
-#define CFG_BCR		0
+#define CONFIG_SYS_BCR		0
 
 /*-----------------------------------------------------------------------
  * SIUMCR - SIU Module Configuration                             4-31
  *-----------------------------------------------------------------------
  */
-#define CFG_SIUMCR      (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_BCTLC01)
+#define CONFIG_SYS_SIUMCR      (SIUMCR_DPPC00|SIUMCR_APPC10|SIUMCR_BCTLC01)
 
 /*-----------------------------------------------------------------------
  * SYPCR - System Protection Control                             4-35
@@ -426,10 +426,10 @@
  * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
  */
 #if defined(CONFIG_WATCHDOG)
-#define CFG_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+#define CONFIG_SYS_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
 			 SYPCR_SWRI|SYPCR_SWP|SYPCR_SWE)
 #else
-#define CFG_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
+#define CONFIG_SYS_SYPCR       (SYPCR_SWTC|SYPCR_BMT|SYPCR_PBME|SYPCR_LBME|\
 			 SYPCR_SWRI|SYPCR_SWP)
 #endif /* CONFIG_WATCHDOG */
 
@@ -439,7 +439,7 @@
  * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
  * and enable Time Counter
  */
-#define CFG_TMCNTSC     (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
+#define CONFIG_SYS_TMCNTSC     (TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
 
 /*-----------------------------------------------------------------------
  * PISCR - Periodic Interrupt Status and Control                 4-42
@@ -447,20 +447,20 @@
  * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
  * Periodic timer
  */
-#define CFG_PISCR       (PISCR_PS|PISCR_PTF|PISCR_PTE)
+#define CONFIG_SYS_PISCR       (PISCR_PS|PISCR_PTF|PISCR_PTE)
 
 /*-----------------------------------------------------------------------
  * SCCR - System Clock Control                                   9-8
  *-----------------------------------------------------------------------
  * Ensure DFBRG is Divide by 16
  */
-#define CFG_SCCR        (0x00000028 | SCCR_DFBRG01)
+#define CONFIG_SYS_SCCR        (0x00000028 | SCCR_DFBRG01)
 
 /*-----------------------------------------------------------------------
  * RCCR - RISC Controller Configuration                         13-7
  *-----------------------------------------------------------------------
  */
-#define CFG_RCCR        0
+#define CONFIG_SYS_RCCR        0
 
 /*
  * Init Memory Controller:
@@ -479,60 +479,60 @@
 /* Minimum mask to separate preliminary
  * address ranges for CS[0:2]
  */
-#define CFG_GLOBAL_SDRAM_LIMIT	(32<<20)	/* less than 32 MB */
+#define CONFIG_SYS_GLOBAL_SDRAM_LIMIT	(32<<20)	/* less than 32 MB */
 
-#define CFG_MPTPR       0x6600
+#define CONFIG_SYS_MPTPR       0x6600
 
 /*-----------------------------------------------------------------------------
  * Address for Mode Register Set (MRS) command
  *-----------------------------------------------------------------------------
  */
-#define CFG_MRS_OFFS	0x00000110
+#define CONFIG_SYS_MRS_OFFS	0x00000110
 
 
 /* Bank 0 - FLASH
  */
-#define CFG_BR0_PRELIM  ((CFG_FLASH_BASE & BRx_BA_MSK)  |\
+#define CONFIG_SYS_BR0_PRELIM  ((CONFIG_SYS_FLASH_BASE & BRx_BA_MSK)  |\
 			 BRx_PS_8                       |\
 			 BRx_MS_GPCM_P                  |\
 			 BRx_V)
 
-#define CFG_OR0_PRELIM  (MEG_TO_AM(CFG_FLASH_SIZE)      |\
+#define CONFIG_SYS_OR0_PRELIM  (MEG_TO_AM(CONFIG_SYS_FLASH_SIZE)      |\
 			 ORxG_SCY_6_CLK                 )
 
 #if defined(CONFIG_CMD_NAND)
 /* Bank 1 - NAND Flash
 */
-#define	CFG_NAND_BASE		CFG_NAND0_BASE
-#define	CFG_NAND_SIZE		0x8000
+#define	CONFIG_SYS_NAND_BASE		CONFIG_SYS_NAND0_BASE
+#define	CONFIG_SYS_NAND_SIZE		0x8000
 
-#define CFG_OR_TIMING_NAND	0x000036
+#define CONFIG_SYS_OR_TIMING_NAND	0x000036
 
-#define CFG_BR1_PRELIM  ((CFG_NAND_BASE & BRx_BA_MSK) | BRx_PS_8 | BRx_MS_GPCM_P | BRx_V  )
-#define CFG_OR1_PRELIM  (P2SZ_TO_AM(CFG_NAND_SIZE) | CFG_OR_TIMING_NAND )
+#define CONFIG_SYS_BR1_PRELIM  ((CONFIG_SYS_NAND_BASE & BRx_BA_MSK) | BRx_PS_8 | BRx_MS_GPCM_P | BRx_V  )
+#define CONFIG_SYS_OR1_PRELIM  (P2SZ_TO_AM(CONFIG_SYS_NAND_SIZE) | CONFIG_SYS_OR_TIMING_NAND )
 #endif
 
 /* Bank 2 - 60x bus SDRAM
  */
-#define CFG_PSRT        0x20
-#define CFG_LSRT        0x20
+#define CONFIG_SYS_PSRT        0x20
+#define CONFIG_SYS_LSRT        0x20
 
-#define CFG_BR2_PRELIM  ((CFG_SDRAM_BASE & BRx_BA_MSK)  |\
+#define CONFIG_SYS_BR2_PRELIM  ((CONFIG_SYS_SDRAM_BASE & BRx_BA_MSK)  |\
 			 BRx_PS_32                      |\
 			 BRx_MS_SDRAM_P                 |\
 			 BRx_V)
 
-#define CFG_OR2_PRELIM	CFG_OR2
+#define CONFIG_SYS_OR2_PRELIM	CONFIG_SYS_OR2
 
 
 /* SDRAM initialization values
 */
-#define CFG_OR2    ((~(CFG_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
+#define CONFIG_SYS_OR2    ((~(CONFIG_SYS_GLOBAL_SDRAM_LIMIT-1) & ORxS_SDAM_MSK) |\
 			 ORxS_BPD_4                     |\
 			 ORxS_ROWST_PBI0_A9		|\
 			 ORxS_NUMR_12)
 
-#define CFG_PSDMR  (PSDMR_SDAM_A14_IS_A5 |\
+#define CONFIG_SYS_PSDMR  (PSDMR_SDAM_A14_IS_A5 |\
 			 PSDMR_BSMA_A15_A17           |\
 			 PSDMR_SDA10_PBI0_A10		|\
 			 PSDMR_RFRC_5_CLK               |\
@@ -546,7 +546,7 @@
 /* Bank 3 - UART
 */
 
-#define CFG_BR3_PRELIM  ((CFG_UART_BASE & BRx_BA_MSK) | BRx_PS_8 | BRx_MS_GPCM_P | BRx_V  )
-#define CFG_OR3_PRELIM  (((-CFG_UART_SIZE) & ORxG_AM_MSK) | ORxG_CSNT | ORxG_SCY_1_CLK | ORxG_TRLX )
+#define CONFIG_SYS_BR3_PRELIM  ((CONFIG_SYS_UART_BASE & BRx_BA_MSK) | BRx_PS_8 | BRx_MS_GPCM_P | BRx_V  )
+#define CONFIG_SYS_OR3_PRELIM  (((-CONFIG_SYS_UART_SIZE) & ORxG_AM_MSK) | ORxG_CSNT | ORxG_SCY_1_CLK | ORxG_TRLX )
 
 #endif	/* __CONFIG_H */