* The PS/2 mux on the BMS2003 board needs 450 ms after power on

  before we can access it; add delay in case we are faster (with no
  CF card inserted)

* Cleanup of some init functions

* Make sure SCC Ethernet is always stopped by the time we boot Linux
  to avoid Linux crashes by early packets coming in.

* Accelerate flash accesses on LWMON board by using buffered writes

1 files changed, 33 insertions, 33 deletions

diff --git a/include/configs/DASA_SIM.h b/include/configs/DASA_SIM.h
index 30e978c..5ff9b9e 100644
--- a/include/configs/DASA_SIM.h
+++ b/include/configs/DASA_SIM.h
@@ -12,7 +12,7 @@
  *
  * This program is distributed in the hope that it will be useful,
  * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
  * GNU General Public License for more details.
  *
  * You should have received a copy of the GNU General Public License
@@ -34,20 +34,20 @@
  */
 
 #define CONFIG_IOP480		1	/* This is a IOP480 CPU		*/
-#define CONFIG_DASA_SIM		1	/* ...on a DASA_SIM board 	*/
+#define CONFIG_DASA_SIM		1	/* ...on a DASA_SIM board	*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
+#define CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */
 
-#define CONFIG_CPUCLOCK	        66
-#define CONFIG_BUSCLOCK	        (CONFIG_CPUCLOCK)
+#define CONFIG_CPUCLOCK		66
+#define CONFIG_BUSCLOCK		(CONFIG_CPUCLOCK)
 
-#define CONFIG_BAUDRATE	        9600
+#define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 5 seconds	*/
 #define CONFIG_BOOTCOMMAND	"bootm ffe00000" /* autoboot command	*/
 
-#undef  CONFIG_BOOTARGS
+#undef	CONFIG_BOOTARGS
 
 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
@@ -63,16 +63,16 @@
 				CFG_CMD_IRQ	| \
 				CFG_CMD_BSP	| \
 				CFG_CMD_ASKENV	| \
-				CFG_CMD_ELF     )
+				CFG_CMD_ELF	)
 #else
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
-				CFG_CMD_BSP     )
+				CFG_CMD_BSP	)
 #endif
 
 #if 0 /* Does not appear to be used?!  If it is used, needs to be fixed */
 #define CONFIG_SOFT_I2C			/* Software I2C support enabled */
 #endif
-#define CFG_I2C_EEPROM_ADDR_LEN	1	/* Bytes of address		*/
+#define CFG_I2C_EEPROM_ADDR_LEN 1	/* Bytes of address		*/
 
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
@@ -83,33 +83,33 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200 }
 
-#define CFG_LOAD_ADDR	0x100000	/* default load address	*/
+#define CFG_LOAD_ADDR	0x100000	/* default load address */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
-#define CFG_INIT_RAM_ADDR	0x00df0000 /* inside of SDRAM                   */
+#define CFG_INIT_RAM_ADDR	0x00df0000 /* inside of SDRAM			*/
 #define CFG_INIT_RAM_END	0x0f00	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
@@ -131,37 +131,37 @@
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/
+#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
 #define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	256     /* max number of sectors on one chip	*/
+#define CFG_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
 
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned char   /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x0AA9  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x0556  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned char	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x0AA9	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x0556	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0002  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0000  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0004  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0002	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0000	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0004	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#define	CFG_ENV_IS_IN_FLASH	1
-#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector	*/
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector */
 #define CFG_ENV_SIZE		0x1000	/* Total Size of Environment Sector	*/
 
 #if 0
 #define CFG_ENV_SECT_SIZE	0x8000	/* see README - env sector total size	*/
 #else
-#define CFG_ENV_SECT_SIZE	0x10000	/* see README - env sector total size	*/
+#define CFG_ENV_SECT_SIZE	0x10000 /* see README - env sector total size	*/
 #endif
 
 /*-----------------------------------------------------------------------
@@ -170,12 +170,12 @@
 #define CONFIG_PCI			/* include pci support			*/
 #undef CONFIG_PCI_PNP
 
-#define CONFIG_NET_MULTI		/* Multi ethernet cards support 	*/
+#define CONFIG_NET_MULTI		/* Multi ethernet cards support		*/
 
 #define CONFIG_TULIP
 
-#define CFG_ETH_DEV_FN       0x0000
-#define CFG_ETH_IOBASE       0x0fff0000
+#define CFG_ETH_DEV_FN	     0x0000
+#define CFG_ETH_IOBASE	     0x0fff0000
 #define CFG_PCI9054_DEV_FN   0x0800
 #define CFG_PCI9054_IOBASE   0x0eff0000