* The PS/2 mux on the BMS2003 board needs 450 ms after power on

  before we can access it; add delay in case we are faster (with no
  CF card inserted)

* Cleanup of some init functions

* Make sure SCC Ethernet is always stopped by the time we boot Linux
  to avoid Linux crashes by early packets coming in.

* Accelerate flash accesses on LWMON board by using buffered writes

1 files changed, 129 insertions, 129 deletions

diff --git a/include/configs/CPCI405AB.h b/include/configs/CPCI405AB.h
index 492fe49..3c94ebc 100644
--- a/include/configs/CPCI405AB.h
+++ b/include/configs/CPCI405AB.h
@@ -34,38 +34,38 @@
  */
 
 #define CONFIG_405GP		1	/* This is a PPC405 CPU		*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
 #define CONFIG_CPCI405		1	/* ...on a CPCI405 board	*/
-#define CONFIG_CPCI405_VER2     1       /* ...version 2                 */
-#define CONFIG_CPCI405AB        1       /* ...and special AB version    */
+#define CONFIG_CPCI405_VER2	1	/* ...version 2			*/
+#define CONFIG_CPCI405AB	1	/* ...and special AB version	*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     33333333 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33333333 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
 
 #if 0
-#define CONFIG_PREBOOT                                                          \
-	"crc32 f0207004 ffc 0;"                                                 \
-	"if cmp 0 f0207000 1;"                                                  \
-	"then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;"             \
+#define CONFIG_PREBOOT								\
+	"crc32 f0207004 ffc 0;"							\
+	"if cmp 0 f0207000 1;"							\
+	"then;echo Old CRC is correct;crc32 f0207004 ff4 f0207000;"		\
 	"else;echo Old CRC is bad;fi"
 #endif
 
 #undef	CONFIG_BOOTARGS
-#define CONFIG_BOOTCOMMAND	"bootm 100000"	/* default boot command	*/
+#define CONFIG_BOOTCOMMAND	"bootm 100000"	/* default boot command */
 
-#undef  CONFIG_LOADS_ECHO		/* echo on for serial download	*/
+#undef	CONFIG_LOADS_ECHO		/* echo on for serial download	*/
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_RTC_M48T35A	1		/* ST Electronics M48 timekeeper */
 
-#define CONFIG_BOOTP_MASK       (CONFIG_BOOTP_DEFAULT | \
+#define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | \
 				 CONFIG_BOOTP_DNS | \
 				 CONFIG_BOOTP_DNS2 | \
 				 CONFIG_BOOTP_SEND_HOSTNAME )
@@ -81,7 +81,7 @@
 				CFG_CMD_I2C	| \
 				CFG_CMD_MII	| \
 				CFG_CMD_PING	| \
-				CFG_CMD_EEPROM  )
+				CFG_CMD_EEPROM	)
 
 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION
@@ -89,9 +89,9 @@
 /* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
 #include <cmd_confdefs.h>
 
-#undef  CONFIG_WATCHDOG			/* watchdog disabled		*/
+#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -101,89 +101,89 @@
 
 #undef	CFG_HUSH_PARSER			/* use "hush" command parser	*/
 #ifdef	CFG_HUSH_PARSER
-#define	CFG_PROMPT_HUSH_PS2	"> "
+#define CFG_PROMPT_HUSH_PS2	"> "
 #endif
 
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_DEVICE_NULLDEV      1       /* include nulldev device       */
+#define CFG_DEVICE_NULLDEV	1	/* include nulldev device	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#undef  CFG_EXT_SERIAL_CLOCK           /* no external serial clock used */
-#define CFG_IGNORE_405_UART_ERRATA_59   /* ignore ppc405gp errata #59   */
-#define CFG_BASE_BAUD       691200
+#undef	CFG_EXT_SERIAL_CLOCK	       /* no external serial clock used */
+#define CFG_IGNORE_405_UART_ERRATA_59	/* ignore ppc405gp errata #59	*/
+#define CFG_BASE_BAUD	    691200
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
-#define CONFIG_VERSION_VARIABLE	1       /* include version env variable */
+#define CONFIG_VERSION_VARIABLE 1	/* include version env variable */
 
-#define CFG_RX_ETH_BUFFER	16      /* use 16 rx buffer on 405 emac */
+#define CFG_RX_ETH_BUFFER	16	/* use 16 rx buffer on 405 emac */
 
 /*-----------------------------------------------------------------------
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
-
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_AUTO   /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
-
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
-
-#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
-
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0405  /* PCI Device ID: CPCI-405      */
-#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A    */
-#define CFG_PCI_CLASSCODE       0x0b20  /* PCI Class Code: Processor/PPC*/
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0xfc000001      /* 64MB, enable hard-wired to 1 */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xffc00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xffc00001      /* 4MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define PCI_HOST_ADAPTER 0		/* configure as pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
+
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_AUTO	/* select pci host function	*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
+
+#define CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
+
+#define CONFIG_PCI_BOOTDELAY	0	/* enable pci bootdelay variable*/
+
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0405	/* PCI Device ID: CPCI-405	*/
+#define CFG_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A	*/
+#define CFG_PCI_CLASSCODE	0x0b20	/* PCI Class Code: Processor/PPC*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0xfc000001	/* 64MB, enable hard-wired to 1 */
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xffc00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xffc00001	/* 4MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * IDE/ATA stuff
  *-----------------------------------------------------------------------
  */
-#undef  CONFIG_IDE_8xx_DIRECT               /* no pcmcia interface required */
-#undef  CONFIG_IDE_LED                  /* no led for ide supported     */
+#undef	CONFIG_IDE_8xx_DIRECT		    /* no pcmcia interface required */
+#undef	CONFIG_IDE_LED			/* no led for ide supported	*/
 #define CONFIG_IDE_RESET	1	/* reset for ide supported	*/
 
-#define	CFG_IDE_MAXBUS	        1		/* max. 1 IDE busses	*/
-#define	CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
+#define CFG_IDE_MAXBUS		1		/* max. 1 IDE busses	*/
+#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
 
-#define	CFG_ATA_BASE_ADDR	0xF0100000
-#define	CFG_ATA_IDE0_OFFSET	0x0000
+#define CFG_ATA_BASE_ADDR	0xF0100000
+#define CFG_ATA_IDE0_OFFSET	0x0000
 
 #define CFG_ATA_DATA_OFFSET	0x0000	/* Offset for data I/O			*/
-#define	CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
+#define CFG_ATA_REG_OFFSET	0x0000	/* Offset for normal register accesses	*/
 #define CFG_ATA_ALT_OFFSET	0x0000	/* Offset for alternate registers	*/
 
 /*-----------------------------------------------------------------------
@@ -212,21 +212,21 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#define CFG_JFFS2_FIRST_BANK    0           /* use for JFFS2 */
-#define CFG_JFFS2_NUM_BANKS     1           /* ! second bank contains U-Boot */
+#define CFG_JFFS2_FIRST_BANK	0	    /* use for JFFS2 */
+#define CFG_JFFS2_NUM_BANKS	1	    /* ! second bank contains U-Boot */
 
 /*-----------------------------------------------------------------------
  * I2C EEPROM (CAT24WC32) for environment
@@ -236,20 +236,20 @@
 #define CFG_I2C_SLAVE		0x7F
 
 #define CFG_I2C_EEPROM_ADDR	0x50	/* EEPROM CAT28WC32		*/
-#define CFG_I2C_EEPROM_ADDR_LEN	2	/* Bytes of address		*/
-/* mask of address bits that overflow into the "EEPROM chip address"    */
+#define CFG_I2C_EEPROM_ADDR_LEN 2	/* Bytes of address		*/
+/* mask of address bits that overflow into the "EEPROM chip address"	*/
 #define CFG_I2C_EEPROM_ADDR_OVERFLOW	0x01
 #define CFG_EEPROM_PAGE_WRITE_BITS 5	/* The Catalyst CAT24WC32 has	*/
 					/* 32 byte page write mode using*/
-					/* last	5 bits of the address	*/
+					/* last 5 bits of the address	*/
 #define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10   /* and takes up to 10 msec */
 #define CFG_EEPROM_PAGE_WRITE_ENABLE
 
 /* Use EEPROM for environment variables */
 
-#define CFG_ENV_IS_IN_EEPROM    1       /* use EEPROM for environment vars */
-#define CFG_ENV_OFFSET          0x000   /* environment starts at the beginning of the EEPROM */
-#define CFG_ENV_SIZE            0x800   /* 2048 bytes may be used for env vars*/
+#define CFG_ENV_IS_IN_EEPROM	1	/* use EEPROM for environment vars */
+#define CFG_ENV_OFFSET		0x000	/* environment starts at the beginning of the EEPROM */
+#define CFG_ENV_SIZE		0x800	/* 2048 bytes may be used for env vars*/
 				   /* total size of a CAT24WC32 is 4096 bytes */
 
 #define CFG_NVRAM_BASE_ADDR	0xf0200000		/* NVRAM base address	*/
@@ -259,8 +259,8 @@
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's    */
-					/* have only 8kB, 16kB is save here     */
+#define CFG_DCACHE_SIZE		16384	/* For IBM 405 CPUs, older 405 ppc's	*/
+					/* have only 8kB, 16kB is save here	*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
@@ -279,89 +279,89 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (Flash Bank 1) initialization                                  */
-#define CFG_EBC_PB1AP           0x92015480
-#define CFG_EBC_PB1CR           0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 1 (Flash Bank 1) initialization					*/
+#define CFG_EBC_PB1AP		0x92015480
+#define CFG_EBC_PB1CR		0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 2 (CAN0, 1) initialization                                       */
-#define CFG_EBC_PB2AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB2CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
-#define CFG_LED_ADDR            0xF0000380
+/* Memory Bank 2 (CAN0, 1) initialization					*/
+#define CFG_EBC_PB2AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB2CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
+#define CFG_LED_ADDR		0xF0000380
 
-/* Memory Bank 3 (CompactFlash IDE) initialization                              */
-#define CFG_EBC_PB3AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB3CR           0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+/* Memory Bank 3 (CompactFlash IDE) initialization				*/
+#define CFG_EBC_PB3AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB3CR		0xF011A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 4 (NVRAM/RTC) initialization                                     */
-/*#define CFG_EBC_PB4AP           0x01805280  / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1     */
-#define CFG_EBC_PB4AP           0x01805680  /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1     */
-#define CFG_EBC_PB4CR           0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 4 (NVRAM/RTC) initialization					*/
+/*#define CFG_EBC_PB4AP		  0x01805280  / * TWT=3,WBN=1,WBF=1,TH=1,SOR=1	   */
+#define CFG_EBC_PB4AP		0x01805680  /* TWT=3,WBN=1,WBF=1,TH=3,SOR=1	*/
+#define CFG_EBC_PB4CR		0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 5 (optional Quart) initialization                                */
-#define CFG_EBC_PB5AP           0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
-#define CFG_EBC_PB5CR           0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 5 (optional Quart) initialization				*/
+#define CFG_EBC_PB5AP		0x04005B80  /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
+#define CFG_EBC_PB5CR		0xF0318000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 6 (FPGA internal) initialization                                 */
-#define CFG_EBC_PB6AP           0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
-#define CFG_EBC_PB6CR           0xF041A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
-#define CFG_FPGA_BASE_ADDR      0xF0400000
+/* Memory Bank 6 (FPGA internal) initialization					*/
+#define CFG_EBC_PB6AP		0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
+#define CFG_EBC_PB6CR		0xF041A000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
+#define CFG_FPGA_BASE_ADDR	0xF0400000
 
 /*-----------------------------------------------------------------------
  * FPGA stuff
  */
 /* FPGA internal regs */
-#define CFG_FPGA_MODE           0x00
-#define CFG_FPGA_STATUS         0x02
-#define CFG_FPGA_TS             0x04
-#define CFG_FPGA_TS_LOW         0x06
-#define CFG_FPGA_TS_CAP0        0x10
-#define CFG_FPGA_TS_CAP0_LOW    0x12
-#define CFG_FPGA_TS_CAP1        0x14
-#define CFG_FPGA_TS_CAP1_LOW    0x16
-#define CFG_FPGA_TS_CAP2        0x18
-#define CFG_FPGA_TS_CAP2_LOW    0x1a
-#define CFG_FPGA_TS_CAP3        0x1c
-#define CFG_FPGA_TS_CAP3_LOW    0x1e
+#define CFG_FPGA_MODE		0x00
+#define CFG_FPGA_STATUS		0x02
+#define CFG_FPGA_TS		0x04
+#define CFG_FPGA_TS_LOW		0x06
+#define CFG_FPGA_TS_CAP0	0x10
+#define CFG_FPGA_TS_CAP0_LOW	0x12
+#define CFG_FPGA_TS_CAP1	0x14
+#define CFG_FPGA_TS_CAP1_LOW	0x16
+#define CFG_FPGA_TS_CAP2	0x18
+#define CFG_FPGA_TS_CAP2_LOW	0x1a
+#define CFG_FPGA_TS_CAP3	0x1c
+#define CFG_FPGA_TS_CAP3_LOW	0x1e
 
 /* FPGA Mode Reg */
-#define CFG_FPGA_MODE_CF_RESET      0x0001
+#define CFG_FPGA_MODE_CF_RESET	    0x0001
 #define CFG_FPGA_MODE_DUART_RESET   0x0002
 #define CFG_FPGA_MODE_ENABLE_OUTPUT 0x0004     /* only set on CPCI-405 Ver 3 */
 #define CFG_FPGA_MODE_TS_IRQ_ENABLE 0x0100
 #define CFG_FPGA_MODE_TS_IRQ_CLEAR  0x1000
-#define CFG_FPGA_MODE_TS_CLEAR      0x2000
+#define CFG_FPGA_MODE_TS_CLEAR	    0x2000
 
 /* FPGA Status Reg */
-#define CFG_FPGA_STATUS_DIP0    0x0001
-#define CFG_FPGA_STATUS_DIP1    0x0002
-#define CFG_FPGA_STATUS_DIP2    0x0004
-#define CFG_FPGA_STATUS_FLASH   0x0008
-#define CFG_FPGA_STATUS_TS_IRQ  0x1000
+#define CFG_FPGA_STATUS_DIP0	0x0001
+#define CFG_FPGA_STATUS_DIP1	0x0002
+#define CFG_FPGA_STATUS_DIP2	0x0004
+#define CFG_FPGA_STATUS_FLASH	0x0008
+#define CFG_FPGA_STATUS_TS_IRQ	0x1000
 
-#define CFG_FPGA_SPARTAN2       1           /* using Xilinx Spartan 2 now    */
-#define CFG_FPGA_MAX_SIZE       128*1024    /* 128kByte is enough for XC2S30 */
+#define CFG_FPGA_SPARTAN2	1	    /* using Xilinx Spartan 2 now    */
+#define CFG_FPGA_MAX_SIZE	128*1024    /* 128kByte is enough for XC2S30 */
 
 /* FPGA program pin configuration */
-#define CFG_FPGA_PRG            0x04000000  /* FPGA program pin (ppc output) */
-#define CFG_FPGA_CLK            0x02000000  /* FPGA clk pin (ppc output)     */
-#define CFG_FPGA_DATA           0x01000000  /* FPGA data pin (ppc output)    */
-#define CFG_FPGA_INIT           0x00010000  /* FPGA init pin (ppc input)     */
-#define CFG_FPGA_DONE           0x00008000  /* FPGA done pin (ppc input)     */
+#define CFG_FPGA_PRG		0x04000000  /* FPGA program pin (ppc output) */
+#define CFG_FPGA_CLK		0x02000000  /* FPGA clk pin (ppc output)     */
+#define CFG_FPGA_DATA		0x01000000  /* FPGA data pin (ppc output)    */
+#define CFG_FPGA_INIT		0x00010000  /* FPGA init pin (ppc input)     */
+#define CFG_FPGA_DONE		0x00008000  /* FPGA done pin (ppc input)     */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */
-#define CFG_INIT_DCACHE_CS      7       /* use cs # 7 for data cache memory    */
+#define CFG_INIT_DCACHE_CS	7	/* use cs # 7 for data cache memory    */
 
-#define CFG_INIT_RAM_ADDR       0x40000000  /* use data cache                  */
-#define CFG_INIT_RAM_END        0x2000  /* End of used area in RAM             */
+#define CFG_INIT_RAM_ADDR	0x40000000  /* use data cache		       */
+#define CFG_INIT_RAM_END	0x2000	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 
 /*