* The PS/2 mux on the BMS2003 board needs 450 ms after power on

  before we can access it; add delay in case we are faster (with no
  CF card inserted)

* Cleanup of some init functions

* Make sure SCC Ethernet is always stopped by the time we boot Linux
  to avoid Linux crashes by early packets coming in.

* Accelerate flash accesses on LWMON board by using buffered writes

1 files changed, 63 insertions, 63 deletions

diff --git a/include/configs/AR405.h b/include/configs/AR405.h
index 847edbc..1fae916 100644
--- a/include/configs/AR405.h
+++ b/include/configs/AR405.h
@@ -34,12 +34,12 @@
  */
 
 #define CONFIG_405GP		1	/* This is a PPC405GP CPU	*/
-#define CONFIG_4xx		1	/* ...member of PPC4xx family   */
-#define CONFIG_AR405		1	/* ...on a AR405 board	        */
+#define CONFIG_4xx		1	/* ...member of PPC4xx family	*/
+#define CONFIG_AR405		1	/* ...on a AR405 board		*/
 
-#define CONFIG_BOARD_PRE_INIT   1       /* call board_pre_init()        */
+#define CONFIG_BOARD_EARLY_INIT_F 1	/* call board_early_init_f()	*/
 
-#define CONFIG_SYS_CLK_FREQ     33000000 /* external frequency to pll   */
+#define CONFIG_SYS_CLK_FREQ	33000000 /* external frequency to pll	*/
 
 #define CONFIG_BAUDRATE		9600
 #define CONFIG_BOOTDELAY	3	/* autoboot after 3 seconds	*/
@@ -51,8 +51,8 @@
 #endif
 
 #if 0
-#define CONFIG_BOOTARGS		"root=/dev/nfs "                        \
-    "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 "        \
+#define CONFIG_BOOTARGS		"root=/dev/nfs "			\
+    "ip=192.168.2.176:192.168.2.190:192.168.2.79:255.255.255.0 "	\
     "nfsroot=192.168.2.190:/home/stefan/cpci405/target_ftest4"
 #else
 #define CONFIG_BOOTARGS		"root=/dev/hda1 "			\
@@ -64,7 +64,7 @@
 #define CFG_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
 
 #define CONFIG_MII		1	/* MII PHY management		*/
-#define	CONFIG_PHY_ADDR		0	/* PHY address			*/
+#define CONFIG_PHY_ADDR		0	/* PHY address			*/
 
 #define CONFIG_COMMANDS	      ( CONFIG_CMD_DFL	| \
 				CFG_CMD_PCI	| \
@@ -76,7 +76,7 @@
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
-#define	CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
+#define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0	*/
 
 /*
  * Miscellaneous configurable options
@@ -84,30 +84,30 @@
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
 #if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-#define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
-#define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
+#define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
 #endif
 #define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
 #define CFG_MAXARGS	16		/* max number of command args	*/
 #define CFG_BARGSIZE	CFG_CBSIZE	/* Boot Argument Buffer Size	*/
 
-#define CFG_CONSOLE_INFO_QUIET  1       /* don't print console @ startup*/
+#define CFG_CONSOLE_INFO_QUIET	1	/* don't print console @ startup*/
 
 #define CFG_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CFG_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
 
-#define CFG_EXT_SERIAL_CLOCK    14745600 /* use external serial clock   */
+#define CFG_EXT_SERIAL_CLOCK	14745600 /* use external serial clock	*/
 
 /* The following table includes the supported baudrates */
-#define CFG_BAUDRATE_TABLE      \
+#define CFG_BAUDRATE_TABLE	\
 	{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 	 57600, 115200, 230400, 460800, 921600 }
 
 #define CFG_LOAD_ADDR	0x100000	/* default load address */
 #define CFG_EXTBDINFO	1		/* To use extended board_into (bd_t) */
 
-#define	CFG_HZ		1000		/* decrementer freq: 1 ms ticks	*/
+#define CFG_HZ		1000		/* decrementer freq: 1 ms ticks */
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 
@@ -115,27 +115,27 @@
  * PCI stuff
  *-----------------------------------------------------------------------
  */
-#define PCI_HOST_ADAPTER 0              /* configure ar pci adapter     */
-#define PCI_HOST_FORCE  1               /* configure as pci host        */
-#define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
+#define PCI_HOST_ADAPTER 0		/* configure ar pci adapter	*/
+#define PCI_HOST_FORCE	1		/* configure as pci host	*/
+#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
 
-#define CONFIG_PCI			/* include pci support	        */
-#define CONFIG_PCI_HOST	PCI_HOST_FORCE  /* select pci host function     */
-#define CONFIG_PCI_PNP			/* do pci plug-and-play         */
-					/* resource configuration       */
+#define CONFIG_PCI			/* include pci support		*/
+#define CONFIG_PCI_HOST PCI_HOST_FORCE	/* select pci host function	*/
+#define CONFIG_PCI_PNP			/* do pci plug-and-play		*/
+					/* resource configuration	*/
 
-#define CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
+#define CONFIG_PCI_SCAN_SHOW		/* print pci devices @ startup	*/
 
-#define CONFIG_PCI_BOOTDELAY    0       /* enable pci bootdelay variable*/
+#define CONFIG_PCI_BOOTDELAY	0	/* enable pci bootdelay variable*/
 
-#define CFG_PCI_SUBSYS_VENDORID 0x12FE  /* PCI Vendor ID: esd gmbh      */
-#define CFG_PCI_SUBSYS_DEVICEID 0x0403  /* PCI Device ID: ARISTO405     */
-#define CFG_PCI_PTM1LA  0x00000000      /* point to sdram               */
-#define CFG_PCI_PTM1MS  0x80000001      /* 2GB, enable hard-wired to 1  */
-#define CFG_PCI_PTM1PCI 0x00000000      /* Host: use this pci address   */
-#define CFG_PCI_PTM2LA  0xfff00000      /* point to flash               */
-#define CFG_PCI_PTM2MS  0xfff00001      /* 1MB, enable                  */
-#define CFG_PCI_PTM2PCI 0x04000000      /* Host: use this pci address   */
+#define CFG_PCI_SUBSYS_VENDORID 0x12FE	/* PCI Vendor ID: esd gmbh	*/
+#define CFG_PCI_SUBSYS_DEVICEID 0x0403	/* PCI Device ID: ARISTO405	*/
+#define CFG_PCI_PTM1LA	0x00000000	/* point to sdram		*/
+#define CFG_PCI_PTM1MS	0x80000001	/* 2GB, enable hard-wired to 1	*/
+#define CFG_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
+#define CFG_PCI_PTM2LA	0xfff00000	/* point to flash		*/
+#define CFG_PCI_PTM2MS	0xfff00001	/* 1MB, enable			*/
+#define CFG_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
 
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
@@ -163,24 +163,24 @@
 #define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
 #define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_WORD_SIZE     unsigned short  /* flash word size (width)      */
-#define CFG_FLASH_ADDR0         0x5555  /* 1st address for flash config cycles  */
-#define CFG_FLASH_ADDR1         0x2AAA  /* 2nd address for flash config cycles  */
+#define CFG_FLASH_WORD_SIZE	unsigned short	/* flash word size (width)	*/
+#define CFG_FLASH_ADDR0		0x5555	/* 1st address for flash config cycles	*/
+#define CFG_FLASH_ADDR1		0x2AAA	/* 2nd address for flash config cycles	*/
 /*
  * The following defines are added for buggy IOP480 byte interface.
  * All other boards should use the standard values (CPCI405 etc.)
  */
-#define CFG_FLASH_READ0         0x0000  /* 0 is standard                        */
-#define CFG_FLASH_READ1         0x0001  /* 1 is standard                        */
-#define CFG_FLASH_READ2         0x0002  /* 2 is standard                        */
+#define CFG_FLASH_READ0		0x0000	/* 0 is standard			*/
+#define CFG_FLASH_READ1		0x0001	/* 1 is standard			*/
+#define CFG_FLASH_READ2		0x0002	/* 2 is standard			*/
 
-#define CFG_FLASH_EMPTY_INFO            /* print 'E' for empty sector on flinfo */
+#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
 
-#define	CFG_ENV_IS_IN_FLASH	1
-#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector	*/
+#define CFG_ENV_IS_IN_FLASH	1
+#define CFG_ENV_OFFSET		0x00010000	/* Offset of Environment Sector */
 #define CFG_ENV_SIZE		0x1000	/* Total Size of Environment Sector	*/
 
-#define CFG_ENV_SECT_SIZE	0x10000	/* see README - env sector total size	*/
+#define CFG_ENV_SECT_SIZE	0x10000 /* see README - env sector total size	*/
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
@@ -204,40 +204,40 @@
  * External Bus Controller (EBC) Setup
  */
 
-/* Memory Bank 0 (Flash Bank 0) initialization                                  */
-#define CFG_EBC_PB0AP           0x92015480
-#define CFG_EBC_PB0CR           0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 0 (Flash Bank 0) initialization					*/
+#define CFG_EBC_PB0AP		0x92015480
+#define CFG_EBC_PB0CR		0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 
-/* Memory Bank 1 (CAN0, 1, 2, 3) initialization                                 */
-#define CFG_EBC_PB1AP           0x01000380  /* enable Ready, BEM=0              */
-#define CFG_EBC_PB1CR           0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 1 (CAN0, 1, 2, 3) initialization					*/
+#define CFG_EBC_PB1AP		0x01000380  /* enable Ready, BEM=0		*/
+#define CFG_EBC_PB1CR		0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 2 (Expension Bus) initialization                                 */
-#define CFG_EBC_PB2AP           0x01000280  /* disable Ready, BEM=0             */
-#define CFG_EBC_PB2CR           0xF0118000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 2 (Expension Bus) initialization					*/
+#define CFG_EBC_PB2AP		0x01000280  /* disable Ready, BEM=0		*/
+#define CFG_EBC_PB2CR		0xF0118000  /* BAS=0xF01,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 3 (16552) initialization                                         */
-#define CFG_EBC_PB3AP           0x01000380  /* enable Ready, BEM=0              */
-#define CFG_EBC_PB3CR           0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit  */
+/* Memory Bank 3 (16552) initialization						*/
+#define CFG_EBC_PB3AP		0x01000380  /* enable Ready, BEM=0		*/
+#define CFG_EBC_PB3CR		0xF0218000  /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit	*/
 
-/* Memory Bank 4 (FPGA regs) initialization                                     */
-#define CFG_EBC_PB4AP           0x01005380  /* enable Ready, BEM=0              */
-#define CFG_EBC_PB4CR           0xF031C000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=32bit */
+/* Memory Bank 4 (FPGA regs) initialization					*/
+#define CFG_EBC_PB4AP		0x01005380  /* enable Ready, BEM=0		*/
+#define CFG_EBC_PB4CR		0xF031C000  /* BAS=0xF03,BS=1MB,BU=R/W,BW=32bit */
 
-/* Memory Bank 5 (Flash Bank 1/DUMMY) initialization                            */
-#define CFG_EBC_PB5AP           0x92015480
-#define CFG_EBC_PB5CR           0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
+/* Memory Bank 5 (Flash Bank 1/DUMMY) initialization				*/
+#define CFG_EBC_PB5AP		0x92015480
+#define CFG_EBC_PB5CR		0xFF85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in data cache)
  */
-#define CFG_INIT_DCACHE_CS      7       /* use cs # 7 for data cache memory    */
+#define CFG_INIT_DCACHE_CS	7	/* use cs # 7 for data cache memory    */
 
-#define CFG_INIT_RAM_ADDR       0x40000000  /* use data cache                  */
-#define CFG_INIT_RAM_END        0x2000  /* End of used area in RAM             */
+#define CFG_INIT_RAM_ADDR	0x40000000  /* use data cache		       */
+#define CFG_INIT_RAM_END	0x2000	/* End of used area in RAM	       */
 #define CFG_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 #define CFG_GBL_DATA_OFFSET    (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET      CFG_GBL_DATA_OFFSET
+#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
 
 /*
  * Internal Definitions