summaryrefslogtreecommitdiff
path: root/include/configs/ADS860.h
diff options
context:
space:
mode:
authorwdenk <wdenk>2002-10-11 15:28:05 +0000
committerwdenk <wdenk>2002-10-11 15:28:05 +0000
commita9ab73b02ae09f7a3ecda92012e9ab61d08b800d (patch)
treeeb3925e8429557745c5f803d6901e2b7a31351a9 /include/configs/ADS860.h
parenta17d0ff41dcd890d12f58b68c73a27a767869581 (diff)
downloadu-boot-imx-a9ab73b02ae09f7a3ecda92012e9ab61d08b800d.zip
u-boot-imx-a9ab73b02ae09f7a3ecda92012e9ab61d08b800d.tar.gz
u-boot-imx-a9ab73b02ae09f7a3ecda92012e9ab61d08b800d.tar.bz2
Initial revision
Diffstat (limited to 'include/configs/ADS860.h')
-rw-r--r--include/configs/ADS860.h479
1 files changed, 479 insertions, 0 deletions
diff --git a/include/configs/ADS860.h b/include/configs/ADS860.h
new file mode 100644
index 0000000..1b73692
--- /dev/null
+++ b/include/configs/ADS860.h
@@ -0,0 +1,479 @@
+/*
+ * A collection of structures, addresses, and values associated with
+ * the Motorola 860 ADS board. Copied from the MBX stuff.
+ * Magnus Damm added defines for 8xxrom and extended bd_info.
+ * Helmut Buchsbaum added bitvalues for BCSRx
+ *
+ * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
+ */
+
+/* ------------------------------------------------------------------------- */
+
+#ifndef _CONFIG_ADS860_H
+#define _CONFIG_ADS860_H
+
+/*
+ * High Level Configuration Options
+ * (easy to change)
+ */
+#include <mpc8xx_irq.h>
+
+#define CONFIG_MPC860 1
+#define CONFIG_ADS 1
+
+#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
+#undef CONFIG_8xx_CONS_SMC2
+#undef CONFIG_8xx_CONS_NONE
+#define CONFIG_BAUDRATE 19200 /* console baudrate */
+#define CONFIG_PCMCIA 1 /* To enable PCMCIA support */
+
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CFG_I2C_SPEED 400000 /* I2C speed and slave address defaults */
+#define CFG_I2C_SLAVE 0x7F
+
+#define MPC8XX_XIN 32768 /* 32.768 kHz input frequency */
+#define MPC8XX_FACT 0x5F6 /* Multiply by 1526 */
+ /* MPC8XX_FACT * MPC8XX_XIN = 50 MHz */
+
+#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
+
+#if 0
+#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
+#else
+#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
+#endif
+
+#undef CONFIG_BOOTARGS
+#define CONFIG_BOOTCOMMAND \
+ "bootp; " \
+ "setenv bootargs root=/dev/nfs rw nfsroot=$(serverip):$(rootpath) " \
+ "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off; " \
+ "bootm"
+
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#undef CFG_LOADS_BAUD_CHANGE /* don't allow baudrate change */
+
+#undef CONFIG_WATCHDOG /* watchdog disabled */
+
+#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE)
+
+
+#if 0 /* private command defs */
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_I2C | \
+ CFG_CMD_IDE | CFG_CMD_PCMCIA)
+#endif
+ /* default command defs */
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL & ~CFG_CMD_CACHE)
+
+/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
+#include <cmd_confdefs.h>
+
+
+/*
+ * Miscellaneous configurable options
+ */
+#undef CFG_LONGHELP /* undef to save memory */
+#define CFG_PROMPT "=>" /* Monitor Command Prompt */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
+#else
+#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
+#endif
+#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
+#define CFG_MAXARGS 16 /* max number of command args */
+#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
+
+#define CFG_MEMTEST_START 0x00100000 /* memtest works on */
+#define CFG_MEMTEST_END 0x00F00000 /* 1 ... 15 MB in DRAM */
+
+#define CFG_LOAD_ADDR 0x00100000
+
+#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+
+#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
+
+/*
+ * Low Level Configuration Settings
+ * (address mappings, register initial values, etc.)
+ * You should know what you are doing if you make changes here.
+ */
+/*-----------------------------------------------------------------------
+ * Internal Memory Mapped Register
+ */
+#define CFG_IMMR 0xfff00000
+#define CFG_IMMR_SIZE ((uint)(64 * 1024))
+
+/*-----------------------------------------------------------------------
+ * Definitions for initial stack pointer and data area (in DPRAM)
+ */
+#define CFG_INIT_RAM_ADDR CFG_IMMR
+#define CFG_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
+#define CFG_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
+#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
+
+/*-----------------------------------------------------------------------
+ * Start addresses for the final memory configuration
+ * (Set up by the startup code)
+ * Please note that CFG_SDRAM_BASE _must_ start at 0
+ */
+#define CFG_SDRAM_BASE 0x00000000
+#define CFG_SRAM_BASE 0x00000000
+#define CFG_FLASH_BASE 0xfe000000
+#define CFG_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */
+
+#define CFG_MONITOR_LEN (384 << 10) /* Reserve 384 kB for Monitor */
+#define CFG_MONITOR_BASE CFG_FLASH_BASE
+#define CFG_MALLOC_LEN (384 << 10) /* Reserve 384 kB for malloc() */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
+/*-----------------------------------------------------------------------
+ * FLASH organization
+ */
+#define CFG_MAX_FLASH_BANKS 1 /* max number of memory banks */
+#define CFG_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
+
+#define CFG_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
+#define CFG_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
+
+#undef CFG_ENV_IS_IN_NVRAM
+#undef CFG_ENV_IS_IN_EEPROM
+#define CFG_ENV_IS_IN_FLASH 1
+
+#define CFG_ENV_OFFSET 0x00040000
+#define CFG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
+#define CFG_ENV_SECT_SIZE 0x40000 /* see README - env sector total size */
+
+/* the other CS:s are determined by looking at parameters in BCSRx */
+
+/*-----------------------------------------------------------------------
+ * Cache Configuration
+ */
+#define CFG_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
+#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#define CFG_CACHELINE_SHIFT 4 /* log base 2 of the above value */
+#endif
+
+/*-----------------------------------------------------------------------
+ * SYPCR - System Protection Control 11-9
+ * SYPCR can only be written once after reset!
+ *-----------------------------------------------------------------------
+ * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
+ */
+#if defined(CONFIG_WATCHDOG)
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
+ SYPCR_SWE | SYPCR_SWRI | SYPCR_SWP)
+#else
+#define CFG_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
+#endif
+
+/*-----------------------------------------------------------------------
+ * SUMCR - SIU Module Configuration 11-6
+ *-----------------------------------------------------------------------
+ * PCMCIA config., multi-function pin tri-state
+ */
+#define CFG_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
+
+/*-----------------------------------------------------------------------
+ * TBSCR - Time Base Status and Control 11-26
+ *-----------------------------------------------------------------------
+ * Clear Reference Interrupt Status, Timebase freezing enabled
+ */
+#define CFG_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE)
+
+/*-----------------------------------------------------------------------
+ * PISCR - Periodic Interrupt Status and Control 11-31
+ *-----------------------------------------------------------------------
+ * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
+ */
+#define CFG_PISCR (PISCR_PS | PISCR_PITF)
+
+/*-----------------------------------------------------------------------
+ * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
+ *-----------------------------------------------------------------------
+ * set the PLL, the low-power modes and the reset control (15-29)
+ */
+#define CFG_PLPRCR (((MPC8XX_FACT-1) << 20) | \
+ PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
+
+/*-----------------------------------------------------------------------
+ * SCCR - System Clock and reset Control Register 15-27
+ *-----------------------------------------------------------------------
+ * Set clock output, timebase and RTC source and divider,
+ * power management and some other internal clocks
+ */
+#define SCCR_MASK SCCR_EBDF11
+#define CFG_SCCR (SCCR_TBS | SCCR_COM00 | SCCR_DFSYNC00 | \
+ SCCR_DFBRG00 | SCCR_DFNL000 | SCCR_DFNH000 | \
+ SCCR_DFLCD000 | SCCR_DFALCD00)
+
+
+ /*-----------------------------------------------------------------------
+ *
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_DER 0
+
+/* Because of the way the 860 starts up and assigns CS0 the
+* entire address space, we have to set the memory controller
+* differently. Normally, you write the option register
+* first, and then enable the chip select by writing the
+* base register. For CS0, you must write the base register
+* first, followed by the option register.
+*/
+
+/*
+ * Init Memory Controller:
+ *
+ * BR0/1 and OR0/1 (FLASH)
+ */
+/* the other CS:s are determined by looking at parameters in BCSRx */
+
+#define BCSR_ADDR ((uint) 0xff010000)
+#define BCSR_SIZE ((uint)(64 * 1024))
+
+#define FLASH_BASE0_PRELIM 0xfe000000 /* FLASH bank #0 */
+#define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */
+
+#define CFG_REMAP_OR_AM 0xff000000 /* OR addr mask */
+#define CFG_PRELIM_OR_AM 0xffe00000 /* OR addr mask */
+
+/* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */
+#define CFG_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
+
+#define CFG_OR0_REMAP (CFG_REMAP_OR_AM | CFG_OR_TIMING_FLASH)
+
+#ifdef USE_REAL_FLASH_VALUES
+/*
+ * These values fit our FADS860T ...
+ * The "default" behaviour with 1Mbyte initial doesn't work for us!
+ */
+#define CFG_BR0_PRELIM 0x0fe000001 /* Real values for the board */
+#define CFG_OR0_PRELIM 0x0ffe00d34
+#define CFG_BR2_PRELIM 0x000000081
+#define CFG_OR2_PRELIM 0x0ff000800
+#else
+#define CFG_OR0_PRELIM (CFG_PRELIM_OR_AM | CFG_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/
+#define CFG_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )
+#endif
+
+/* BCSRx - Board Control and Status Registers */
+/* #define CFG_OR1_REMAP CFG_OR0_REMAP */
+#define CFG_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */
+#define CFG_BR1_PRELIM ((BCSR_ADDR) | BR_V )
+
+/*
+ * Memory Periodic Timer Prescaler
+ */
+
+/* periodic timer for refresh */
+#define CFG_MAMR_PTA 97 /* start with divider for 100 MHz */
+
+/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
+#define CFG_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
+
+/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
+#define CFG_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
+#define CFG_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
+
+/*
+ * MAMR settings for SDRAM
+ */
+
+/* 8 column SDRAM */
+#define CFG_MAMR_8COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+/* 9 column SDRAM */
+#define CFG_MAMR_9COL ((CFG_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
+ MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
+ MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
+
+#define CFG_MAMR 0x13a01114
+/*
+ * Internal Definitions
+ *
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+
+/* values according to the manual */
+#define BCSR0 ((uint) (BCSR_ADDR + 00))
+#define BCSR1 ((uint) (BCSR_ADDR + 0x04))
+#define BCSR2 ((uint) (BCSR_ADDR + 0x08))
+#define BCSR3 ((uint) (BCSR_ADDR + 0x0c))
+#define BCSR4 ((uint) (BCSR_ADDR + 0x10))
+
+
+/*-----------------------------------------------------------------------
+ * PCMCIA stuff
+ *-----------------------------------------------------------------------
+ *
+ */
+#define CFG_PCMCIA_MEM_ADDR (0xE0000000)
+#define CFG_PCMCIA_MEM_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_DMA_ADDR (0xE4000000)
+#define CFG_PCMCIA_DMA_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_ATTRB_ADDR (0xE8000000)
+#define CFG_PCMCIA_ATTRB_SIZE ( 64 << 20 )
+#define CFG_PCMCIA_IO_ADDR (0xEC000000)
+#define CFG_PCMCIA_IO_SIZE ( 64 << 20 )
+
+
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff
+ *-----------------------------------------------------------------------
+ */
+#define CONFIG_IDE_8xx_DIRECT 1 /* PCMCIA interface required */
+#undef CONFIG_IDE_LED /* LED for ide supported */
+#define CONFIG_IDE_RESET 1 /* reset for ide supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 2 IDE busses */
+#define CFG_IDE_MAXDEVICE (CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
+
+#define CFG_PIO_MODE 0 /* IDE interface in PIO Mode 0 */
+#define CFG_PC_IDE_RESET ((ushort)0x0008) /* PC 12 */
+
+/* #define CFG_ATA_BASE_ADDR 0xFE100000 */
+#define CFG_ATA_BASE_ADDR CFG_PCMCIA_MEM_ADDR
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
+#define CFG_ATA_REG_OFFSET 0x0080 /* Offset for normal register accesses */
+#define CFG_ATA_ALT_OFFSET 0x0100 /* Offset for alternate registers */
+
+
+/* (F)ADS bitvalues by Helmut Buchsbaum
+ * see MPC8xxADS User's Manual for a proper description
+ * of the following structures
+ */
+
+#define BCSR0_ERB ((uint)0x80000000)
+#define BCSR0_IP ((uint)0x40000000)
+#define BCSR0_BDIS ((uint)0x10000000)
+#define BCSR0_BPS_MASK ((uint)0x0C000000)
+#define BCSR0_ISB_MASK ((uint)0x01800000)
+#define BCSR0_DBGC_MASK ((uint)0x00600000)
+#define BCSR0_DBPC_MASK ((uint)0x00180000)
+#define BCSR0_EBDF_MASK ((uint)0x00060000)
+
+#define BCSR1_FLASH_EN ((uint)0x80000000)
+#define BCSR1_DRAM_EN ((uint)0x40000000)
+#define BCSR1_ETHEN ((uint)0x20000000)
+#define BCSR1_IRDEN ((uint)0x10000000)
+#define BCSR1_FLASH_CFG_EN ((uint)0x08000000)
+#define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
+#define BCSR1_BCSR_EN ((uint)0x02000000)
+#define BCSR1_RS232EN_1 ((uint)0x01000000)
+#define BCSR1_PCCEN ((uint)0x00800000)
+#define BCSR1_PCCVCC0 ((uint)0x00400000)
+#define BCSR1_PCCVCCON BCSR1_PCCVCC0
+#define BCSR1_PCCVPP_MASK ((uint)0x00300000)
+#define BCSR1_DRAM_HALF_WORD ((uint)0x00080000)
+#define BCSR1_RS232EN_2 ((uint)0x00040000)
+#define BCSR1_SDRAM_EN ((uint)0x00020000)
+#define BCSR1_PCCVCC1 ((uint)0x00010000)
+
+#define BCSR2_FLASH_PD_MASK ((uint)0xF0000000)
+#define BCSR2_DRAM_PD_MASK ((uint)0x07800000)
+#define BCSR2_DRAM_PD_SHIFT (23)
+#define BCSR2_EXTTOLI_MASK ((uint)0x00780000)
+#define BCSR2_DBREVNR_MASK ((uint)0x00030000)
+
+#define BCSR3_DBID_MASK ((ushort)0x3800)
+#define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
+#define BCSR3_BREVNR0 ((ushort)0x0080)
+#define BCSR3_FLASH_PD_MASK ((ushort)0x0070)
+#define BCSR3_BREVN1 ((ushort)0x0008)
+#define BCSR3_BREVN2_MASK ((ushort)0x0003)
+
+#define BCSR4_ETHLOOP ((uint)0x80000000)
+#define BCSR4_TFPLDL ((uint)0x40000000)
+#define BCSR4_TPSQEL ((uint)0x20000000)
+#define BCSR4_SIGNAL_LAMP ((uint)0x10000000)
+#ifdef CONFIG_MPC823
+#define BCSR4_USB_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860SAR
+#define BCSR4_UTOPIA_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC860SAR */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETH_EN ((uint)0x08000000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_USB_SPEED ((uint)0x04000000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHCFG0 ((uint)0x04000000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_VCCO ((uint)0x02000000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHFDE ((uint)0x02000000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_VIDEO_ON ((uint)0x00800000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC823
+#define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHCFG1 ((uint)0x00400000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_VIDEO_RST ((uint)0x00200000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC860T
+#define BCSR4_FETHRST ((uint)0x00200000)
+#endif /* CONFIG_MPC860T */
+#ifdef CONFIG_MPC823
+#define BCSR4_MODEM_EN ((uint)0x00100000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC823
+#define BCSR4_DATA_VOICE ((uint)0x00080000)
+#endif /* CONFIG_MPC823 */
+#ifdef CONFIG_MPC850
+#define BCSR4_DATA_VOICE ((uint)0x00080000)
+#endif /* CONFIG_MPC850 */
+
+#define CONFIG_DRAM_50MHZ 1
+#define CONFIG_SDRAM_50MHZ
+
+#ifdef CONFIG_MPC860T
+/* Interrupt level assignments.
+ */
+#define FEC_INTERRUPT SIU_LEVEL1 /* FEC interrupt */
+#endif /* CONFIG_MPC860T */
+
+/* We don't use the 8259.
+ */
+#define NR_8259_INTS 0
+
+/* Machine type
+ */
+#define _MACH_8xx (_MACH_ads)
+
+#if 0
+#define CONFIG_DISK_SPINUP_TIME 1000000
+#endif
+#undef CONFIG_DISK_SPINUP_TIME /* usinī Compact Flash */
+
+
+/* PCMCIA configuration
+ */
+#define PCMCIA_MAX_SLOTS 2
+#ifdef CONFIG_MPC860
+#define PCMCIA_SLOT_A 1
+#endif
+
+#endif /* _CONFIG_ADS860_H */