summaryrefslogtreecommitdiff
path: root/include/commproc.h
diff options
context:
space:
mode:
authorMasahiro Yamada <yamada.m@jp.panasonic.com>2014-04-04 15:25:03 +0900
committerTom Rini <trini@ti.com>2014-04-18 10:42:29 -0400
commitd6b11fd1f0ef1b6cbc81ca7655c47bf68a16f32d (patch)
tree7842ceb3aa2ed0178611d168da341cace09dafca /include/commproc.h
parenta146e8b189abf73b8bac0bfa9c8c3c1b3bfe5507 (diff)
downloadu-boot-imx-d6b11fd1f0ef1b6cbc81ca7655c47bf68a16f32d.zip
u-boot-imx-d6b11fd1f0ef1b6cbc81ca7655c47bf68a16f32d.tar.gz
u-boot-imx-d6b11fd1f0ef1b6cbc81ca7655c47bf68a16f32d.tar.bz2
powerpc: remove MBX and MBX860T boards support
Enough time has passed since these boards were moved to Orphan. Remove. - Remove board/mbx8xx/* - Remove include/configs/{MBX.h,MBX860T.h} - Clean-up if defined(CONFIG_MBX) - Move the entries from boards.cfg to doc/README.scrapyard Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Diffstat (limited to 'include/commproc.h')
-rw-r--r--include/commproc.h32
1 files changed, 0 insertions, 32 deletions
diff --git a/include/commproc.h b/include/commproc.h
index 12b9421..62468c3 100644
--- a/include/commproc.h
+++ b/include/commproc.h
@@ -12,10 +12,6 @@
* CPM capabilities. I (or someone else) will add definitions as they
* are needed. -- Dan
*
- * On the MBX board, EPPC-Bug loads CPM microcode into the first 512
- * bytes of the DP RAM and relocates the I2C parameter area to the
- * IDMA1 space. The remaining DP RAM is available for buffer descriptors
- * or other use.
*/
#ifndef __CPM_8XX__
#define __CPM_8XX__
@@ -135,7 +131,6 @@ typedef struct cpm_buf_desc {
#define PROFF_SMC2 ((uint)0x0380)
/* Define enough so I can at least use the serial port as a UART.
- * The MBX uses SMC1 as the host serial port.
*/
typedef struct smc_uart {
ushort smc_rbase; /* Rx Buffer descriptor base address */
@@ -888,33 +883,6 @@ typedef struct scc_enet {
#define SICR_ENET_CLKRT ((uint)0x00003E00)
#endif /* CONFIG_LWMON */
-/*** MBX ************************************************************/
-
-#ifdef CONFIG_MBX
-/* Bits in parallel I/O port registers that have to be set/cleared
- * to configure the pins for SCC1 use. The TCLK and RCLK seem unique
- * to the MBX860 board. Any two of the four available clocks could be
- * used, and the MPC860 cookbook manual has an example using different
- * clock pins.
- */
-#define PROFF_ENET PROFF_SCC1
-#define CPM_CR_ENET CPM_CR_CH_SCC1
-#define SCC_ENET 0
-#define PA_ENET_RXD ((ushort)0x0001)
-#define PA_ENET_TXD ((ushort)0x0002)
-#define PA_ENET_TCLK ((ushort)0x0200)
-#define PA_ENET_RCLK ((ushort)0x0800)
-#define PC_ENET_TENA ((ushort)0x0001)
-#define PC_ENET_CLSN ((ushort)0x0010)
-#define PC_ENET_RENA ((ushort)0x0020)
-
-/* Control bits in the SICR to route TCLK (CLK2) and RCLK (CLK4) to
- * SCC1. Also, make sure GR1 (bit 24) and SC1 (bit 25) are zero.
- */
-#define SICR_ENET_MASK ((uint)0x000000ff)
-#define SICR_ENET_CLKRT ((uint)0x0000003d)
-#endif /* CONFIG_MBX */
-
/*** KM8XX *********************************************************/
/* The KM8XX Service Module uses SCC3 for Ethernet */