summaryrefslogtreecommitdiff
path: root/include/ata.h
diff options
context:
space:
mode:
authormushtaq khan <mushtaq_k@procsys.com>2007-04-20 14:23:02 +0530
committerWolfgang Denk <wd@denx.de>2007-05-15 23:25:37 +0200
commit66d9dbec1cc27d6398ee6cf84639dbe14971251e (patch)
tree55c162c1992cf22fb7a94cb71009e5a9e87f36f9 /include/ata.h
parent644e6fb4eb8be90ea04ba34b643a8bf019d680e0 (diff)
downloadu-boot-imx-66d9dbec1cc27d6398ee6cf84639dbe14971251e.zip
u-boot-imx-66d9dbec1cc27d6398ee6cf84639dbe14971251e.tar.gz
u-boot-imx-66d9dbec1cc27d6398ee6cf84639dbe14971251e.tar.bz2
Add driver for S-ATA-controller on Intel processors with South
Bridge, ICH-5, ICH-6 and ICH-7. Implementation: 1. Code is divided in to two files. All functions, which are controller specific are kept in "drivers/ata_piix.c" file and functions, which are not controller specific, are kept in "common/cmd_sata.c" file. 2. Reading and Writing from the S-ATA drive is done using PIO method. 3. Driver can be configured for 48-bit addressing by defining macro CONFIG_LBA48, if this macro is not defined driver uses the 28-bit addressing. 4. S-ATA read function is hooked to the File system, commands like ext2ls and ext2load file can be used. This has been tested. 5. U-Boot command "SATA_init" is added, which initializes the S-ATA controller and identifies the S-ATA drives connected to it. 6. U-Boot command "sata" is added, which is used to read/write, print partition table and get info about the drives present. This I have implemented in same way as "ide" command is implemented in U-Boot. 7. This driver is for S-ATA in native mode. 8. This driver does not support the Native command queuing and Hot-plugging. Signed-off-by: Mushtaq Khan <mushtaq_k@procsys.com>
Diffstat (limited to 'include/ata.h')
-rw-r--r--include/ata.h60
1 files changed, 60 insertions, 0 deletions
diff --git a/include/ata.h b/include/ata.h
index 8584226..d36bdf6 100644
--- a/include/ata.h
+++ b/include/ata.h
@@ -83,6 +83,66 @@
#define ATA_DEVICE(x) ((x & 1)<<4)
#define ATA_LBA 0xE0
+enum {
+ ATA_MAX_DEVICES = 1, /* per bus/port */
+ ATA_MAX_PRD = 256, /* we could make these 256/256 */
+ ATA_SECT_SIZE = 256, /*256 words per sector */
+
+ /* bits in ATA command block registers */
+ ATA_HOB = (1 << 7), /* LBA48 selector */
+ ATA_NIEN = (1 << 1), /* disable-irq flag */
+ /*ATA_LBA = (1 << 6), *//* LBA28 selector */
+ ATA_DEV1 = (1 << 4), /* Select Device 1 (slave) */
+ ATA_DEVICE_OBS = (1 << 7) | (1 << 5), /* obs bits in dev reg */
+ ATA_DEVCTL_OBS = (1 << 3), /* obsolete bit in devctl reg */
+ ATA_BUSY = (1 << 7), /* BSY status bit */
+ ATA_DRDY = (1 << 6), /* device ready */
+ ATA_DF = (1 << 5), /* device fault */
+ ATA_DRQ = (1 << 3), /* data request i/o */
+ ATA_ERR = (1 << 0), /* have an error */
+ ATA_SRST = (1 << 2), /* software reset */
+ ATA_ABORTED = (1 << 2), /* command aborted */
+ /* ATA command block registers */
+ ATA_REG_DATA = 0x00,
+ ATA_REG_ERR = 0x01,
+ ATA_REG_NSECT = 0x02,
+ ATA_REG_LBAL = 0x03,
+ ATA_REG_LBAM = 0x04,
+ ATA_REG_LBAH = 0x05,
+ ATA_REG_DEVICE = 0x06,
+ ATA_REG_STATUS = 0x07,
+ ATA_PCI_CTL_OFS = 0x02,
+ /* and their aliases */
+ ATA_REG_FEATURE = ATA_REG_ERR,
+ ATA_REG_CMD = ATA_REG_STATUS,
+ ATA_REG_BYTEL = ATA_REG_LBAM,
+ ATA_REG_BYTEH = ATA_REG_LBAH,
+ ATA_REG_DEVSEL = ATA_REG_DEVICE,
+ ATA_REG_IRQ = ATA_REG_NSECT,
+
+ /* SETFEATURES stuff */
+ SETFEATURES_XFER = 0x03,
+ XFER_UDMA_7 = 0x47,
+ XFER_UDMA_6 = 0x46,
+ XFER_UDMA_5 = 0x45,
+ XFER_UDMA_4 = 0x44,
+ XFER_UDMA_3 = 0x43,
+ XFER_UDMA_2 = 0x42,
+ XFER_UDMA_1 = 0x41,
+ XFER_UDMA_0 = 0x40,
+ XFER_MW_DMA_2 = 0x22,
+ XFER_MW_DMA_1 = 0x21,
+ XFER_MW_DMA_0 = 0x20,
+ XFER_PIO_4 = 0x0C,
+ XFER_PIO_3 = 0x0B,
+ XFER_PIO_2 = 0x0A,
+ XFER_PIO_1 = 0x09,
+ XFER_PIO_0 = 0x08,
+ XFER_SW_DMA_2 = 0x12,
+ XFER_SW_DMA_1 = 0x11,
+ XFER_SW_DMA_0 = 0x10,
+ XFER_PIO_SLOW = 0x00
+};
/*
* ATA Commands (only mandatory commands listed here)
*/