drivers/hwmon : move hardware monitor drviers to drivers/hwmon

Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

1 files changed, 0 insertions, 174 deletions

diff --git a/dtt/adm1021.c b/dtt/adm1021.c
deleted file mode 100644
index 9f65cfb..0000000
--- a/dtt/adm1021.c
+++ /dev/null
@@ -1,174 +0,0 @@
-/*
- * (C) Copyright 2003
- * Murray Jensen, CSIRO-MIT, Murray.Jensen@csiro.au
- *
- * based on dtt/lm75.c which is ...
- *
- * (C) Copyright 2001
- * Bill Hunter,  Wave 7 Optics, williamhunter@mediaone.net
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- */
-
-/*
- * Analog Devices's ADM1021
- * "Low Cost Microprocessor System Temperature Monitor"
- */
-
-#include <common.h>
-
-#ifdef CONFIG_DTT_ADM1021
-
-#include <i2c.h>
-#include <dtt.h>
-
-typedef
-	struct {
-		uint i2c_addr:7;	/* 7bit i2c chip address */
-		uint conv_rate:3;	/* conversion rate */
-		uint enable_alert:1;	/* enable alert output pin */
-		uint enable_local:1;	/* enable internal temp sensor */
-		uint max_local:8;	/* internal temp maximum */
-		uint min_local:8;	/* internal temp minimum */
-		uint enable_remote:1;	/* enable remote temp sensor */
-		uint max_remote:8;	/* remote temp maximum */
-		uint min_remote:8;	/* remote temp minimum */
-	}
-dtt_cfg_t;
-
-dtt_cfg_t dttcfg[] = CFG_DTT_ADM1021;
-
-int
-dtt_read (int sensor, int reg)
-{
-	dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
-	uchar data;
-
-	if (i2c_read(dcp->i2c_addr, reg, 1, &data, 1) != 0)
-		return -1;
-
-	return (int)data;
-} /* dtt_read() */
-
-int
-dtt_write (int sensor, int reg, int val)
-{
-	dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
-	uchar data;
-
-	data = (uchar)(val & 0xff);
-
-	if (i2c_write(dcp->i2c_addr, reg, 1, &data, 1) != 0)
-		return 1;
-
-	return 0;
-} /* dtt_write() */
-
-static int
-_dtt_init (int sensor)
-{
-	dtt_cfg_t *dcp = &dttcfg[sensor >> 1];
-	int reg, val;
-
-	if (((sensor & 1) == 0 ? dcp->enable_local : dcp->enable_remote) == 0)
-		return 1;	/* sensor is disabled (or rather ignored) */
-
-	/*
-	 * Setup High Limit register
-	 */
-	if ((sensor & 1) == 0) {
-		reg = DTT_WRITE_LOC_HIGHLIM;
-		val = dcp->max_local;
-	}
-	else {
-		reg = DTT_WRITE_REM_HIGHLIM;
-		val = dcp->max_remote;
-	}
-	if (dtt_write (sensor, reg, val) != 0)
-		return 1;
-
-	/*
-	 * Setup Low Limit register
-	 */
-	if ((sensor & 1) == 0) {
-		reg = DTT_WRITE_LOC_LOWLIM;
-		val = dcp->min_local;
-	}
-	else {
-		reg = DTT_WRITE_REM_LOWLIM;
-		val = dcp->min_remote;
-	}
-	if (dtt_write (sensor, reg, val) != 0)
-		return 1;
-
-	/* shouldn't hurt if the rest gets done twice */
-
-	/*
-	 * Setup Conversion Rate register
-	 */
-	if (dtt_write (sensor, DTT_WRITE_CONVRATE, dcp->conv_rate) != 0)
-		return 1;
-
-	/*
-	 * Setup configuraton register
-	 */
-	val = 0;				/* running */
-	if (dcp->enable_alert == 0)
-		val |= DTT_CONFIG_ALERT_MASKED;	/* mask ALERT pin */
-	if (dtt_write (sensor, DTT_WRITE_CONFIG, val) != 0)
-		return 1;
-
-	return 0;
-} /* _dtt_init() */
-
-int
-dtt_init (void)
-{
-	int i;
-	unsigned char sensors[] = CONFIG_DTT_SENSORS;
-	const char *const header = "DTT:   ";
-
-	/* switch to correct I2C bus */
-	I2C_SET_BUS(CFG_DTT_BUS_NUM);
-
-	for (i = 0; i < sizeof(sensors); i++) {
-		if (_dtt_init(sensors[i]) != 0)
-			printf ("%s%d FAILED INIT\n", header, i+1);
-		else
-			printf ("%s%d is %i C\n", header, i+1,
-				dtt_get_temp(sensors[i]));
-	}
-
-	return (0);
-} /* dtt_init() */
-
-int
-dtt_get_temp (int sensor)
-{
-	signed char val;
-
-	if ((sensor & 1) == 0)
-		val = dtt_read(sensor, DTT_READ_LOC_VALUE);
-	else
-		val = dtt_read(sensor, DTT_READ_REM_VALUE);
-
-	return (int) val;
-} /* dtt_get_temp() */
-
-#endif /* CONFIG_DTT_ADM1021 */