diff options
| author | Sudhakar Rajashekhara <sudhakar.raj@ti.com> | 2010-11-18 09:59:37 -0500 |
|---|---|---|
| committer | Sandeep Paulraj <s-paulraj@ti.com> | 2010-11-30 11:27:44 -0500 |
| commit | d26074012b1ae28e4d593fabde389a3dc4471114 (patch) | |
| tree | 7678e3a4733b9943df1b360e9781252a16844027 /drivers | |
| parent | 48571ff00526701c88cfcac1294adf20aeeade74 (diff) | |
| download | u-boot-imx-d26074012b1ae28e4d593fabde389a3dc4471114.zip u-boot-imx-d26074012b1ae28e4d593fabde389a3dc4471114.tar.gz u-boot-imx-d26074012b1ae28e4d593fabde389a3dc4471114.tar.bz2 | |
da850: Add RMII support for EMAC
This patch is a port of the work by Sudhakar Rajeshekhara in commit
ab3effbcad8851cc65dc5241a01c064d2030a3b2 of
git://arago-project.org/git/people/sandeep/u-boot-davinci.git.
The da850 UI board has on it an RMII PHY which can be used if the MDC line
to the MII PHY on the baseboard is disabled and the RMII PHY is enabled by
configuring the values of some GPIO pins on the IO expander of the UI board.
This patch implements disabling that line via GPIO2[6], configuring the UI
board's IO expander and setting only the pinmux settings that are needed for
RMII operation.
Tested on da850evm by adding a define for CONFIG_DRIVER_TI_EMAC_USE_RMII.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Ben Gardiner <bengardiner@nanometrics.ca>
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Ben Warren <biggerbadderben@gmail.com>
CC: Mike Frysinger <vapier@gentoo.org>
CC: Sughosh Ganu <urwithsughosh@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Diffstat (limited to 'drivers')
| -rw-r--r-- | drivers/net/davinci_emac.c | 41 |
1 files changed, 40 insertions, 1 deletions
diff --git a/drivers/net/davinci_emac.c b/drivers/net/davinci_emac.c index e06896f..43a3d79 100644 --- a/drivers/net/davinci_emac.c +++ b/drivers/net/davinci_emac.c @@ -243,8 +243,35 @@ static int gen_get_link_speed(int phy_addr) { u_int16_t tmp; - if (davinci_eth_phy_read(phy_addr, MII_STATUS_REG, &tmp) && (tmp & 0x04)) + if (davinci_eth_phy_read(phy_addr, MII_STATUS_REG, &tmp) && + (tmp & 0x04)) { +#if defined(CONFIG_DRIVER_TI_EMAC_USE_RMII) && \ + defined(CONFIG_MACH_DAVINCI_DA850_EVM) + davinci_eth_phy_read(phy_addr, PHY_ANLPAR, &tmp); + + /* Speed doesn't matter, there is no setting for it in EMAC. */ + if (tmp & (PHY_ANLPAR_TXFD | PHY_ANLPAR_10FD)) { + /* set EMAC for Full Duplex */ + writel(EMAC_MACCONTROL_MIIEN_ENABLE | + EMAC_MACCONTROL_FULLDUPLEX_ENABLE, + &adap_emac->MACCONTROL); + } else { + /*set EMAC for Half Duplex */ + writel(EMAC_MACCONTROL_MIIEN_ENABLE, + &adap_emac->MACCONTROL); + } + + if (tmp & (PHY_ANLPAR_TXFD | PHY_ANLPAR_TX)) + writel(readl(&adap_emac->MACCONTROL) | + EMAC_MACCONTROL_RMIISPEED_100, + &adap_emac->MACCONTROL); + else + writel(readl(&adap_emac->MACCONTROL) & + ~EMAC_MACCONTROL_RMIISPEED_100, + &adap_emac->MACCONTROL); +#endif return(1); + } return(0); } @@ -326,6 +353,12 @@ static int davinci_eth_open(struct eth_device *dev, bd_t *bis) } #endif +#if defined(CONFIG_DRIVER_TI_EMAC_USE_RMII) && \ + defined(CONFIG_MACH_DAVINCI_DA850_EVM) + adap_ewrap->c0rxen = adap_ewrap->c1rxen = adap_ewrap->c2rxen = 0; + adap_ewrap->c0txen = adap_ewrap->c1txen = adap_ewrap->c2txen = 0; + adap_ewrap->c0miscen = adap_ewrap->c1miscen = adap_ewrap->c2miscen = 0; +#endif rx_desc = emac_rx_desc; writel(1, &adap_emac->TXCONTROL); @@ -480,6 +513,12 @@ static void davinci_eth_close(struct eth_device *dev) writel(0, &adap_ewrap->EWCTL); #endif +#if defined(CONFIG_DRIVER_TI_EMAC_USE_RMII) && \ + defined(CONFIG_MACH_DAVINCI_DA850_EVM) + adap_ewrap->c0rxen = adap_ewrap->c1rxen = adap_ewrap->c2rxen = 0; + adap_ewrap->c0txen = adap_ewrap->c1txen = adap_ewrap->c2txen = 0; + adap_ewrap->c0miscen = adap_ewrap->c1miscen = adap_ewrap->c2miscen = 0; +#endif debug_emac("- emac_close\n"); } |