Merge branch 'upstream'

9 files changed, 1197 insertions, 149 deletions

diff --git a/drivers/Makefile b/drivers/Makefile
index d68cba6..c7fcc3f 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -30,7 +30,7 @@ LIB	= $(obj)libdrivers.a
 COBJS	= 3c589.o 5701rls.o ali512x.o atmel_usart.o \
 	  bcm570x.o bcm570x_autoneg.o cfb_console.o cfi_flash.o \
 	  cs8900.o ct69000.o dataflash.o dc2114x.o dm9000x.o \
-	  e1000.o eepro100.o \
+	  e1000.o eepro100.o enc28j60.o \
 	  i8042.o inca-ip_sw.o keyboard.o \
 	  lan91c96.o macb.o \
 	  natsemi.o ne2000.o netarm_eth.o netconsole.o \
diff --git a/drivers/enc28j60.c b/drivers/enc28j60.c
new file mode 100755
index 0000000..98303ac
--- /dev/null
+++ b/drivers/enc28j60.c
@@ -0,0 +1,983 @@
+/*
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <config.h>
+#include <common.h>
+#ifdef CONFIG_ENC28J60
+#include <net.h>
+#include <asm/arch/hardware.h>
+#include <asm/arch/spi.h>
+
+/*
+ * Control Registers in Bank 0
+ */
+
+#define CTL_REG_ERDPTL	 0x00
+#define CTL_REG_ERDPTH	 0x01
+#define CTL_REG_EWRPTL	 0x02
+#define CTL_REG_EWRPTH	 0x03
+#define CTL_REG_ETXSTL	 0x04
+#define CTL_REG_ETXSTH	 0x05
+#define CTL_REG_ETXNDL	 0x06
+#define CTL_REG_ETXNDH	 0x07
+#define CTL_REG_ERXSTL	 0x08
+#define CTL_REG_ERXSTH	 0x09
+#define CTL_REG_ERXNDL	 0x0A
+#define CTL_REG_ERXNDH	 0x0B
+#define CTL_REG_ERXRDPTL 0x0C
+#define CTL_REG_ERXRDPTH 0x0D
+#define CTL_REG_ERXWRPTL 0x0E
+#define CTL_REG_ERXWRPTH 0x0F
+#define CTL_REG_EDMASTL  0x10
+#define CTL_REG_EDMASTH  0x11
+#define CTL_REG_EDMANDL  0x12
+#define CTL_REG_EDMANDH  0x13
+#define CTL_REG_EDMADSTL 0x14
+#define CTL_REG_EDMADSTH 0x15
+#define CTL_REG_EDMACSL  0x16
+#define CTL_REG_EDMACSH  0x17
+/* these are common in all banks */
+#define CTL_REG_EIE	 0x1B
+#define CTL_REG_EIR	 0x1C
+#define CTL_REG_ESTAT	 0x1D
+#define CTL_REG_ECON2	 0x1E
+#define CTL_REG_ECON1	 0x1F
+
+/*
+ * Control Registers in Bank 1
+ */
+
+#define CTL_REG_EHT0	0x00
+#define CTL_REG_EHT1	0x01
+#define CTL_REG_EHT2	0x02
+#define CTL_REG_EHT3	0x03
+#define CTL_REG_EHT4	0x04
+#define CTL_REG_EHT5	0x05
+#define CTL_REG_EHT6	0x06
+#define CTL_REG_EHT7	0x07
+#define CTL_REG_EPMM0	0x08
+#define CTL_REG_EPMM1	0x09
+#define CTL_REG_EPMM2	0x0A
+#define CTL_REG_EPMM3	0x0B
+#define CTL_REG_EPMM4	0x0C
+#define CTL_REG_EPMM5	0x0D
+#define CTL_REG_EPMM6	0x0E
+#define CTL_REG_EPMM7	0x0F
+#define CTL_REG_EPMCSL	0x10
+#define CTL_REG_EPMCSH	0x11
+#define CTL_REG_EPMOL	0x14
+#define CTL_REG_EPMOH	0x15
+#define CTL_REG_EWOLIE	0x16
+#define CTL_REG_EWOLIR	0x17
+#define CTL_REG_ERXFCON 0x18
+#define CTL_REG_EPKTCNT 0x19
+
+/*
+ * Control Registers in Bank 2
+ */
+
+#define CTL_REG_MACON1	 0x00
+#define CTL_REG_MACON2	 0x01
+#define CTL_REG_MACON3	 0x02
+#define CTL_REG_MACON4	 0x03
+#define CTL_REG_MABBIPG  0x04
+#define CTL_REG_MAIPGL	 0x06
+#define CTL_REG_MAIPGH	 0x07
+#define CTL_REG_MACLCON1 0x08
+#define CTL_REG_MACLCON2 0x09
+#define CTL_REG_MAMXFLL  0x0A
+#define CTL_REG_MAMXFLH  0x0B
+#define CTL_REG_MAPHSUP  0x0D
+#define CTL_REG_MICON	 0x11
+#define CTL_REG_MICMD	 0x12
+#define CTL_REG_MIREGADR 0x14
+#define CTL_REG_MIWRL	 0x16
+#define CTL_REG_MIWRH	 0x17
+#define CTL_REG_MIRDL	 0x18
+#define CTL_REG_MIRDH	 0x19
+
+/*
+ * Control Registers in Bank 3
+ */
+
+#define CTL_REG_MAADR1	0x00
+#define CTL_REG_MAADR0	0x01
+#define CTL_REG_MAADR3	0x02
+#define CTL_REG_MAADR2	0x03
+#define CTL_REG_MAADR5	0x04
+#define CTL_REG_MAADR4	0x05
+#define CTL_REG_EBSTSD	0x06
+#define CTL_REG_EBSTCON 0x07
+#define CTL_REG_EBSTCSL 0x08
+#define CTL_REG_EBSTCSH 0x09
+#define CTL_REG_MISTAT	0x0A
+#define CTL_REG_EREVID	0x12
+#define CTL_REG_ECOCON	0x15
+#define CTL_REG_EFLOCON 0x17
+#define CTL_REG_EPAUSL	0x18
+#define CTL_REG_EPAUSH	0x19
+
+
+/*
+ * PHY Register
+ */
+
+#define PHY_REG_PHID1 0x02
+#define PHY_REG_PHID2 0x03
+/* taken from the Linux driver */
+#define PHY_REG_PHCON1 0x00
+#define PHY_REG_PHCON2 0x10
+#define PHY_REG_PHLCON 0x14
+
+/*
+ * Receive Filter Register (ERXFCON) bits
+ */
+
+#define ENC_RFR_UCEN  0x80
+#define ENC_RFR_ANDOR 0x40
+#define ENC_RFR_CRCEN 0x20
+#define ENC_RFR_PMEN  0x10
+#define ENC_RFR_MPEN  0x08
+#define ENC_RFR_HTEN  0x04
+#define ENC_RFR_MCEN  0x02
+#define ENC_RFR_BCEN  0x01
+
+/*
+ * ECON1 Register Bits
+ */
+
+#define ENC_ECON1_TXRST  0x80
+#define ENC_ECON1_RXRST  0x40
+#define ENC_ECON1_DMAST  0x20
+#define ENC_ECON1_CSUMEN 0x10
+#define ENC_ECON1_TXRTS  0x08
+#define ENC_ECON1_RXEN	 0x04
+#define ENC_ECON1_BSEL1  0x02
+#define ENC_ECON1_BSEL0  0x01
+
+/*
+ * ECON2 Register Bits
+ */
+#define ENC_ECON2_AUTOINC 0x80
+#define ENC_ECON2_PKTDEC  0x40
+#define ENC_ECON2_PWRSV   0x20
+#define ENC_ECON2_VRPS	  0x08
+
+/*
+ * EIR Register Bits
+ */
+#define ENC_EIR_PKTIF  0x40
+#define ENC_EIR_DMAIF  0x20
+#define ENC_EIR_LINKIF 0x10
+#define ENC_EIR_TXIF   0x08
+#define ENC_EIR_WOLIF  0x04
+#define ENC_EIR_TXERIF 0x02
+#define ENC_EIR_RXERIF 0x01
+
+/*
+ * ESTAT Register Bits
+ */
+
+#define ENC_ESTAT_INT	  0x80
+#define ENC_ESTAT_LATECOL 0x10
+#define ENC_ESTAT_RXBUSY  0x04
+#define ENC_ESTAT_TXABRT  0x02
+#define ENC_ESTAT_CLKRDY  0x01
+
+/*
+ * EIE Register Bits
+ */
+
+#define ENC_EIE_INTIE  0x80
+#define ENC_EIE_PKTIE  0x40
+#define ENC_EIE_DMAIE  0x20
+#define ENC_EIE_LINKIE 0x10
+#define ENC_EIE_TXIE   0x08
+#define ENC_EIE_WOLIE  0x04
+#define ENC_EIE_TXERIE 0x02
+#define ENC_EIE_RXERIE 0x01
+
+/*
+ * MACON1 Register Bits
+ */
+#define ENC_MACON1_LOOPBK  0x10
+#define ENC_MACON1_TXPAUS  0x08
+#define ENC_MACON1_RXPAUS  0x04
+#define ENC_MACON1_PASSALL 0x02
+#define ENC_MACON1_MARXEN  0x01
+
+
+/*
+ * MACON2 Register Bits
+ */
+#define ENC_MACON2_MARST   0x80
+#define ENC_MACON2_RNDRST  0x40
+#define ENC_MACON2_MARXRST 0x08
+#define ENC_MACON2_RFUNRST 0x04
+#define ENC_MACON2_MATXRST 0x02
+#define ENC_MACON2_TFUNRST 0x01
+
+/*
+ * MACON3 Register Bits
+ */
+#define ENC_MACON3_PADCFG2 0x80
+#define ENC_MACON3_PADCFG1 0x40
+#define ENC_MACON3_PADCFG0 0x20
+#define ENC_MACON3_TXCRCEN 0x10
+#define ENC_MACON3_PHDRLEN 0x08
+#define ENC_MACON3_HFRMEN  0x04
+#define ENC_MACON3_FRMLNEN 0x02
+#define ENC_MACON3_FULDPX  0x01
+
+/*
+ * MICMD Register Bits
+ */
+#define ENC_MICMD_MIISCAN 0x02
+#define ENC_MICMD_MIIRD   0x01
+
+/*
+ * MISTAT Register Bits
+ */
+#define ENC_MISTAT_NVALID 0x04
+#define ENC_MISTAT_SCAN   0x02
+#define ENC_MISTAT_BUSY   0x01
+
+/*
+ * PHID1 and PHID2 values
+ */
+#define ENC_PHID1_VALUE 0x0083
+#define ENC_PHID2_VALUE 0x1400
+#define ENC_PHID2_MASK	0xFC00
+
+
+#define ENC_SPI_SLAVE_CS 0x00010000	/* pin P1.16 */
+#define ENC_RESET	 0x00020000	/* pin P1.17 */
+
+#define FAILSAFE_VALUE 5000
+
+/*
+ * Controller memory layout:
+ *
+ * 0x0000 - 0x17ff  6k bytes receive buffer
+ * 0x1800 - 0x1fff  2k bytes transmit buffer
+ */
+/* Use the lower memory for receiver buffer. See errata pt. 5 */
+#define ENC_RX_BUF_START 0x0000
+#define ENC_TX_BUF_START 0x1800
+/* taken from the Linux driver */
+#define ENC_RX_BUF_END   0x17ff
+#define ENC_TX_BUF_END   0x1fff
+
+/* maximum frame length */
+#define ENC_MAX_FRM_LEN 1518
+
+#define enc_enable() PUT32(IO1CLR, ENC_SPI_SLAVE_CS)
+#define enc_disable() PUT32(IO1SET, ENC_SPI_SLAVE_CS)
+#define enc_cfg_spi() spi_set_cfg(0, 0, 0); spi_set_clock(8);
+
+
+static unsigned char encReadReg (unsigned char regNo);
+static void encWriteReg (unsigned char regNo, unsigned char data);
+static void encWriteRegRetry (unsigned char regNo, unsigned char data, int c);
+static void encReadBuff (unsigned short length, unsigned char *pBuff);
+static void encWriteBuff (unsigned short length, unsigned char *pBuff);
+static void encBitSet (unsigned char regNo, unsigned char data);
+static void encBitClr (unsigned char regNo, unsigned char data);
+static void encReset (void);
+static void encInit (unsigned char *pEthAddr);
+static unsigned short phyRead (unsigned char addr);
+static void phyWrite(unsigned char, unsigned short);
+static void encPoll (void);
+static void encRx (void);
+
+#define m_nic_read(reg) encReadReg(reg)
+#define m_nic_write(reg, data) encWriteReg(reg, data)
+#define m_nic_write_retry(reg, data, count) encWriteRegRetry(reg, data, count)
+#define m_nic_read_data(len, buf) encReadBuff((len), (buf))
+#define m_nic_write_data(len, buf) encWriteBuff((len), (buf))
+
+/* bit field set */
+#define m_nic_bfs(reg, data) encBitSet(reg, data)
+
+/* bit field clear */
+#define m_nic_bfc(reg, data) encBitClr(reg, data)
+
+static unsigned char bank = 0;	/* current bank in enc28j60 */
+static unsigned char next_pointer_lsb;
+static unsigned char next_pointer_msb;
+
+static unsigned char buffer[ENC_MAX_FRM_LEN];
+static int rxResetCounter = 0;
+
+#define RX_RESET_COUNTER 1000;
+
+/*-----------------------------------------------------------------------------
+ * Always returns 0
+ */
+int eth_init (bd_t * bis)
+{
+	unsigned char estatVal;
+
+	/* configure GPIO */
+	(*((volatile unsigned long *) IO1DIR)) |= ENC_SPI_SLAVE_CS;
+	(*((volatile unsigned long *) IO1DIR)) |= ENC_RESET;
+
+	/* CS and RESET active low */
+	PUT32 (IO1SET, ENC_SPI_SLAVE_CS);
+	PUT32 (IO1SET, ENC_RESET);
+
+	spi_init ();
+
+	/* taken from the Linux driver - dangerous stuff here! */
+	/* Wait for CLKRDY to become set (i.e., check that we can communicate with
+	   the ENC) */
+	do
+	{
+		estatVal = m_nic_read(CTL_REG_ESTAT);
+	} while ((estatVal & 0x08) || (~estatVal & ENC_ESTAT_CLKRDY));
+
+	/* initialize controller */
+	encReset ();
+	encInit (bis->bi_enetaddr);
+
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_RXEN);	/* enable receive */
+
+	return 0;
+}
+
+int eth_send (volatile void *packet, int length)
+{
+	/* check frame length, etc. */
+	/* TODO: */
+
+	/* switch to bank 0 */
+	m_nic_bfc (CTL_REG_ECON1, (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
+
+	/* set EWRPT */
+	m_nic_write (CTL_REG_EWRPTL, (ENC_TX_BUF_START & 0xff));
+	m_nic_write (CTL_REG_EWRPTH, (ENC_TX_BUF_START >> 8));
+
+	/* set ETXND */
+	m_nic_write (CTL_REG_ETXNDL, (length + ENC_TX_BUF_START) & 0xFF);
+	m_nic_write (CTL_REG_ETXNDH, (length + ENC_TX_BUF_START) >> 8);
+
+	/* set ETXST */
+	m_nic_write (CTL_REG_ETXSTL, ENC_TX_BUF_START & 0xFF);
+	m_nic_write (CTL_REG_ETXSTH, ENC_TX_BUF_START >> 8);
+
+	/* write packet */
+	m_nic_write_data (length, (unsigned char *) packet);
+
+	/* taken from the Linux driver */
+	/* Verify that the internal transmit logic has not been altered by excessive
+	   collisions.  See Errata B4 12 and 14.
+	 */
+	if (m_nic_read(CTL_REG_EIR) & ENC_EIR_TXERIF) {
+		m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_TXRST);
+		m_nic_bfc(CTL_REG_ECON1, ENC_ECON1_TXRST);
+	}
+	m_nic_bfc(CTL_REG_EIR, (ENC_EIR_TXERIF | ENC_EIR_TXIF));
+
+	/* set ECON1.TXRTS */
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_TXRTS);
+
+	return 0;
+}
+
+
+/*****************************************************************************
+ * This function resets the receiver only. This function may be called from
+ * interrupt-context.
+ */
+static void encReceiverReset (void)
+{
+	unsigned char econ1;
+
+	econ1 = m_nic_read (CTL_REG_ECON1);
+	if ((econ1 & ENC_ECON1_RXRST) == 0) {
+		m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_RXRST);
+		rxResetCounter = RX_RESET_COUNTER;
+	}
+}
+
+/*****************************************************************************
+ * receiver reset timer
+ */
+static void encReceiverResetCallback (void)
+{
+	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_RXRST);
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_RXEN);	/* enable receive */
+}
+
+/*-----------------------------------------------------------------------------
+ * Check for received packets. Call NetReceive for each packet. The return
+ * value is ignored by the caller.
+ */
+int eth_rx (void)
+{
+	if (rxResetCounter > 0 && --rxResetCounter == 0) {
+		encReceiverResetCallback ();
+	}
+
+	encPoll ();
+
+	return 0;
+}
+
+void eth_halt (void)
+{
+	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_RXEN);	/* disable receive */
+}
+
+/*****************************************************************************/
+
+static void encPoll (void)
+{
+	unsigned char eir_reg;
+	volatile unsigned char estat_reg;
+	unsigned char pkt_cnt;
+
+#ifdef CONFIG_USE_IRQ
+	/* clear global interrupt enable bit in enc28j60 */
+	m_nic_bfc (CTL_REG_EIE, ENC_EIE_INTIE);
+#endif
+	estat_reg = m_nic_read (CTL_REG_ESTAT);
+
+	eir_reg = m_nic_read (CTL_REG_EIR);
+
+	if (eir_reg & ENC_EIR_TXIF) {
+		/* clear TXIF bit in EIR */
+		m_nic_bfc (CTL_REG_EIR, ENC_EIR_TXIF);
+	}
+
+	/* We have to use pktcnt and not pktif bit, see errata pt. 6 */
+
+	/* move to bank 1 */
+	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL1);
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL0);
+
+	/* read pktcnt */
+	pkt_cnt = m_nic_read (CTL_REG_EPKTCNT);
+
+	if (pkt_cnt > 0) {
+		if ((eir_reg & ENC_EIR_PKTIF) == 0) {
+			/*printf("encPoll: pkt cnt > 0, but pktif not set\n"); */
+		}
+		encRx ();
+		/* clear PKTIF bit in EIR, this should not need to be done but it
+		   seems like we get problems if we do not */
+		m_nic_bfc (CTL_REG_EIR, ENC_EIR_PKTIF);
+	}
+
+	if (eir_reg & ENC_EIR_RXERIF) {
+		printf ("encPoll: rx error\n");
+		m_nic_bfc (CTL_REG_EIR, ENC_EIR_RXERIF);
+	}
+	if (eir_reg & ENC_EIR_TXERIF) {
+		printf ("encPoll: tx error\n");
+		m_nic_bfc (CTL_REG_EIR, ENC_EIR_TXERIF);
+	}
+
+#ifdef CONFIG_USE_IRQ
+	/* set global interrupt enable bit in enc28j60 */
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_INTIE);
+#endif
+}
+
+static void encRx (void)
+{
+	unsigned short pkt_len;
+	unsigned short copy_len;
+	unsigned short status;
+	unsigned char eir_reg;
+	unsigned char pkt_cnt = 0;
+	unsigned short rxbuf_rdpt;
+
+	/* switch to bank 0 */
+	m_nic_bfc (CTL_REG_ECON1, (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
+
+	m_nic_write (CTL_REG_ERDPTL, next_pointer_lsb);
+	m_nic_write (CTL_REG_ERDPTH, next_pointer_msb);
+
+	do {
+		m_nic_read_data (6, buffer);
+		next_pointer_lsb = buffer[0];
+		next_pointer_msb = buffer[1];
+		pkt_len = buffer[2];
+		pkt_len |= (unsigned short) buffer[3] << 8;
+		status = buffer[4];
+		status |= (unsigned short) buffer[5] << 8;
+
+		if (pkt_len <= ENC_MAX_FRM_LEN)
+			copy_len = pkt_len;
+		else
+			copy_len = 0;
+
+		if ((status & (1L << 7)) == 0) /* check Received Ok bit */
+			copy_len = 0;
+
+		/* taken from the Linux driver */
+		/* check if next pointer is resonable */
+		if ((((unsigned int)next_pointer_msb << 8) |
+			(unsigned int)next_pointer_lsb) >= ENC_TX_BUF_START)
+			copy_len = 0;
+
+		if (copy_len > 0) {
+			m_nic_read_data (copy_len, buffer);
+		}
+
+		/* advance read pointer to next pointer */
+		m_nic_write (CTL_REG_ERDPTL, next_pointer_lsb);
+		m_nic_write (CTL_REG_ERDPTH, next_pointer_msb);
+
+		/* decrease packet counter */
+		m_nic_bfs (CTL_REG_ECON2, ENC_ECON2_PKTDEC);
+
+		/* taken from the Linux driver */
+		/* Only odd values should be written to ERXRDPTL,
+		 * see errata B4 pt.13
+		 */
+		rxbuf_rdpt = (next_pointer_msb << 8 | next_pointer_lsb) - 1;
+		if ((rxbuf_rdpt < (m_nic_read(CTL_REG_ERXSTH) << 8 |
+				m_nic_read(CTL_REG_ERXSTL))) || (rxbuf_rdpt >
+				(m_nic_read(CTL_REG_ERXNDH) << 8 |
+				m_nic_read(CTL_REG_ERXNDL)))) {
+			m_nic_write(CTL_REG_ERXRDPTL, m_nic_read(CTL_REG_ERXNDL));
+			m_nic_write(CTL_REG_ERXRDPTH, m_nic_read(CTL_REG_ERXNDH));
+		} else {
+			m_nic_write(CTL_REG_ERXRDPTL, rxbuf_rdpt & 0xFF);
+			m_nic_write(CTL_REG_ERXRDPTH, rxbuf_rdpt >> 8);
+		}
+
+		/* move to bank 1 */
+		m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL1);
+		m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL0);
+
+		/* read pktcnt */
+		pkt_cnt = m_nic_read (CTL_REG_EPKTCNT);
+
+		/* switch to bank 0 */
+		m_nic_bfc (CTL_REG_ECON1,
+			   (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
+
+		if (copy_len == 0) {
+			eir_reg = m_nic_read (CTL_REG_EIR);
+			encReceiverReset ();
+			printf ("eth_rx: copy_len=0\n");
+			continue;
+		}
+
+		NetReceive ((unsigned char *) buffer, pkt_len);
+
+		eir_reg = m_nic_read (CTL_REG_EIR);
+	} while (pkt_cnt);	/* Use EPKTCNT not EIR.PKTIF flag, see errata pt. 6 */
+}
+
+static void encWriteReg (unsigned char regNo, unsigned char data)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0x40 | regNo);	/* write in regNo */
+	spi_write (data);
+
+	enc_disable ();
+	enc_enable ();
+
+	spi_write (0x1f);	/* write reg 0x1f */
+
+	enc_disable ();
+	spi_unlock ();
+}
+
+static void encWriteRegRetry (unsigned char regNo, unsigned char data, int c)
+{
+	unsigned char readback;
+	int i;
+
+	spi_lock ();
+
+	for (i = 0; i < c; i++) {
+		enc_cfg_spi ();
+		enc_enable ();
+
+		spi_write (0x40 | regNo);	/* write in regNo */
+		spi_write (data);
+
+		enc_disable ();
+		enc_enable ();
+
+		spi_write (0x1f);	/* write reg 0x1f */
+
+		enc_disable ();
+
+		spi_unlock ();	/* we must unlock spi first */
+
+		readback = encReadReg (regNo);
+
+		spi_lock ();
+
+		if (readback == data)
+			break;
+	}
+	spi_unlock ();
+
+	if (i == c) {
+		printf ("enc28j60: write reg %d failed\n", regNo);
+	}
+}
+
+static unsigned char encReadReg (unsigned char regNo)
+{
+	unsigned char rxByte;
+
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0x1f);	/* read reg 0x1f */
+
+	bank = spi_read () & 0x3;
+
+	enc_disable ();
+	enc_enable ();
+
+	spi_write (regNo);
+	rxByte = spi_read ();
+
+	/* check if MAC or MII register */
+	if (((bank == 2) && (regNo <= 0x1a)) ||
+	    ((bank == 3) && (regNo <= 0x05 || regNo == 0x0a))) {
+		/* ignore first byte and read another byte */
+		rxByte = spi_read ();
+	}
+
+	enc_disable ();
+	spi_unlock ();
+
+	return rxByte;
+}
+
+static void encReadBuff (unsigned short length, unsigned char *pBuff)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0x20 | 0x1a);	/* read buffer memory */
+
+	while (length--) {
+		if (pBuff != NULL)
+			*pBuff++ = spi_read ();
+		else
+			spi_write (0);
+	}
+
+	enc_disable ();
+	spi_unlock ();
+}
+
+static void encWriteBuff (unsigned short length, unsigned char *pBuff)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0x60 | 0x1a);	/* write buffer memory */
+
+	spi_write (0x00);	/* control byte */
+
+	while (length--)
+		spi_write (*pBuff++);
+
+	enc_disable ();
+	spi_unlock ();
+}
+
+static void encBitSet (unsigned char regNo, unsigned char data)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0x80 | regNo);	/* bit field set */
+	spi_write (data);
+
+	enc_disable ();
+	spi_unlock ();
+}
+
+static void encBitClr (unsigned char regNo, unsigned char data)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0xA0 | regNo);	/* bit field clear */
+	spi_write (data);
+
+	enc_disable ();
+	spi_unlock ();
+}
+
+static void encReset (void)
+{
+	spi_lock ();
+	enc_cfg_spi ();
+	enc_enable ();
+
+	spi_write (0xff);	/* soft reset */
+
+	enc_disable ();
+	spi_unlock ();
+
+	/* sleep 1 ms. See errata pt. 2 */
+	udelay (1000);
+}
+
+static void encInit (unsigned char *pEthAddr)
+{
+	unsigned short phid1 = 0;
+	unsigned short phid2 = 0;
+
+	/* switch to bank 0 */
+	m_nic_bfc (CTL_REG_ECON1, (ENC_ECON1_BSEL1 | ENC_ECON1_BSEL0));
+
+	/*
+	 * Setup the buffer space. The reset values are valid for the
+	 * other pointers.
+	 */
+	/* We shall not write to ERXST, see errata pt. 5. Instead we
+	   have to make sure that ENC_RX_BUS_START is 0. */
+	m_nic_write_retry (CTL_REG_ERXSTL, (ENC_RX_BUF_START & 0xFF), 1);
+	m_nic_write_retry (CTL_REG_ERXSTH, (ENC_RX_BUF_START >> 8), 1);
+
+	/* taken from the Linux driver */
+	m_nic_write_retry (CTL_REG_ERXNDL, (ENC_RX_BUF_END & 0xFF), 1);
+	m_nic_write_retry (CTL_REG_ERXNDH, (ENC_RX_BUF_END >> 8), 1);
+
+	m_nic_write_retry (CTL_REG_ERDPTL, (ENC_RX_BUF_START & 0xFF), 1);
+	m_nic_write_retry (CTL_REG_ERDPTH, (ENC_RX_BUF_START >> 8), 1);
+
+	next_pointer_lsb = (ENC_RX_BUF_START & 0xFF);
+	next_pointer_msb = (ENC_RX_BUF_START >> 8);
+
+	/* verify identification */
+	phid1 = phyRead (PHY_REG_PHID1);
+	phid2 = phyRead (PHY_REG_PHID2);
+
+	if (phid1 != ENC_PHID1_VALUE
+	    || (phid2 & ENC_PHID2_MASK) != ENC_PHID2_VALUE) {
+		printf ("ERROR: failed to identify controller\n");
+		printf ("phid1 = %x, phid2 = %x\n",
+			phid1, (phid2 & ENC_PHID2_MASK));
+		printf ("should be phid1 = %x, phid2 = %x\n",
+			ENC_PHID1_VALUE, ENC_PHID2_VALUE);
+	}
+
+	/*
+	 * --- MAC Initialization ---
+	 */
+
+	/* Pull MAC out of Reset */
+
+	/* switch to bank 2 */
+	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* enable MAC to receive frames */
+	/* added some bits from the Linux driver */
+	m_nic_write_retry (CTL_REG_MACON1
+		,(ENC_MACON1_MARXEN | ENC_MACON1_TXPAUS | ENC_MACON1_RXPAUS)
+		,10);
+
+	/* configure pad, tx-crc and duplex */
+	/* added a bit from the Linux driver */
+	m_nic_write_retry (CTL_REG_MACON3
+		,(ENC_MACON3_PADCFG0 | ENC_MACON3_TXCRCEN | ENC_MACON3_FRMLNEN)
+		,10);
+
+	/* added 4 new lines from the Linux driver */
+	/* Allow infinite deferals if the medium is continously busy */
+	m_nic_write_retry(CTL_REG_MACON4, (1<<6) /*ENC_MACON4_DEFER*/, 10);
+
+	/* Late collisions occur beyond 63 bytes */
+	m_nic_write_retry(CTL_REG_MACLCON2, 63, 10);
+
+	/* Set (low byte) Non-Back-to_Back Inter-Packet Gap. Recommended 0x12 */
+	m_nic_write_retry(CTL_REG_MAIPGL, 0x12, 10);
+
+	/*
+	* Set (high byte) Non-Back-to_Back Inter-Packet Gap. Recommended
+	* 0x0c for half-duplex. Nothing for full-duplex
+	*/
+	m_nic_write_retry(CTL_REG_MAIPGH, 0x0C, 10);
+
+	/* set maximum frame length */
+	m_nic_write_retry (CTL_REG_MAMXFLL, (ENC_MAX_FRM_LEN & 0xff), 10);
+	m_nic_write_retry (CTL_REG_MAMXFLH, (ENC_MAX_FRM_LEN >> 8), 10);
+
+	/*
+	 * Set MAC back-to-back inter-packet gap. Recommended 0x12 for half duplex
+	 * and 0x15 for full duplex.
+	 */
+	m_nic_write_retry (CTL_REG_MABBIPG, 0x12, 10);
+
+	/* set MAC address */
+
+	/* switch to bank 3 */
+	m_nic_bfs (CTL_REG_ECON1, (ENC_ECON1_BSEL0 | ENC_ECON1_BSEL1));
+
+	m_nic_write_retry (CTL_REG_MAADR0, pEthAddr[5], 1);
+	m_nic_write_retry (CTL_REG_MAADR1, pEthAddr[4], 1);
+	m_nic_write_retry (CTL_REG_MAADR2, pEthAddr[3], 1);
+	m_nic_write_retry (CTL_REG_MAADR3, pEthAddr[2], 1);
+	m_nic_write_retry (CTL_REG_MAADR4, pEthAddr[1], 1);
+	m_nic_write_retry (CTL_REG_MAADR5, pEthAddr[0], 1);
+
+	/*
+	* PHY Initialization taken from the Linux driver
+	 */
+
+	/* Prevent automatic loopback of data beeing transmitted by setting
+	   ENC_PHCON2_HDLDIS */
+	phyWrite(PHY_REG_PHCON2, (1<<8));
+
+	/* LEDs configuration
+	 * LEDA: LACFG = 0100 -> display link status
+	 * LEDB: LBCFG = 0111 -> display TX & RX activity
+	 * STRCH = 1 -> LED pulses
+	 */
+	phyWrite(PHY_REG_PHLCON, 0x0472);
+
+	/* Reset PDPXMD-bit => half duplex */
+	phyWrite(PHY_REG_PHCON1, 0);
+
+	/*
+	 * Receive settings
+	 */
+
+#ifdef CONFIG_USE_IRQ
+	/* enable interrupts */
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_PKTIE);
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_TXIE);
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_RXERIE);
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_TXERIE);
+	m_nic_bfs (CTL_REG_EIE, ENC_EIE_INTIE);
+#endif
+}
+
+/*****************************************************************************
+ *
+ * Description:
+ *    Read PHY registers.
+ *
+ *    NOTE! This function will change to Bank 2.
+ *
+ * Params:
+ *    [in] addr address of the register to read
+ *
+ * Returns:
+ *    The value in the register
+ */
+static unsigned short phyRead (unsigned char addr)
+{
+	unsigned short ret = 0;
+
+	/* move to bank 2 */
+	m_nic_bfc (CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs (CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* write address to MIREGADR */
+	m_nic_write (CTL_REG_MIREGADR, addr);
+
+	/* set MICMD.MIIRD */
+	m_nic_write (CTL_REG_MICMD, ENC_MICMD_MIIRD);
+
+	/* taken from the Linux driver */
+	/* move to bank 3 */
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* poll MISTAT.BUSY bit until operation is complete */
+	while ((m_nic_read (CTL_REG_MISTAT) & ENC_MISTAT_BUSY) != 0) {
+		static int cnt = 0;
+
+		if (cnt++ >= 1000) {
+			/* GJ - this seems extremely dangerous! */
+			/* printf("#"); */
+			cnt = 0;
+		}
+	}
+
+	/* taken from the Linux driver */
+	/* move to bank 2 */
+	m_nic_bfc(CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* clear MICMD.MIIRD */
+	m_nic_write (CTL_REG_MICMD, 0);
+
+	ret = (m_nic_read (CTL_REG_MIRDH) << 8);
+	ret |= (m_nic_read (CTL_REG_MIRDL) & 0xFF);
+
+	return ret;
+}
+
+/*****************************************************************************
+ *
+ * Taken from the Linux driver.
+ * Description:
+ * Write PHY registers.
+ *
+ * NOTE! This function will change to Bank 3.
+ *
+ * Params:
+ * [in] addr address of the register to write to
+ * [in] data to be written
+ *
+ * Returns:
+ *    None
+ */
+static void phyWrite(unsigned char addr, unsigned short data)
+{
+	/* move to bank 2 */
+	m_nic_bfc(CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* write address to MIREGADR */
+	m_nic_write(CTL_REG_MIREGADR, addr);
+
+	m_nic_write(CTL_REG_MIWRL, data & 0xff);
+	m_nic_write(CTL_REG_MIWRH, data >> 8);
+
+	/* move to bank 3 */
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL0);
+	m_nic_bfs(CTL_REG_ECON1, ENC_ECON1_BSEL1);
+
+	/* poll MISTAT.BUSY bit until operation is complete */
+	while((m_nic_read(CTL_REG_MISTAT) & ENC_MISTAT_BUSY) != 0) {
+		static int cnt = 0;
+
+		if(cnt++ >= 1000) {
+			cnt = 0;
+		}
+	}
+}
+
+#endif /* CONFIG_ENC28J60 */
diff --git a/drivers/nand/nand_base.c b/drivers/nand/nand_base.c
index 8495829..c6fee18 100644
--- a/drivers/nand/nand_base.c
+++ b/drivers/nand/nand_base.c
@@ -427,8 +427,9 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip)
 	struct nand_chip *this = mtd->priv;
 	u16 bad;
 
+	page = (int)(ofs >> this->page_shift) & this->pagemask;
+
 	if (getchip) {
-		page = (int)(ofs >> this->page_shift);
 		chipnr = (int)(ofs >> this->chip_shift);
 
 		/* Grab the lock and see if the device is available */
@@ -436,18 +437,17 @@ static int nand_block_bad(struct mtd_info *mtd, loff_t ofs, int getchip)
 
 		/* Select the NAND device */
 		this->select_chip(mtd, chipnr);
-	} else
-		page = (int) ofs;
+	}
 
 	if (this->options & NAND_BUSWIDTH_16) {
-		this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos & 0xFE, page & this->pagemask);
+		this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos & 0xFE, page);
 		bad = cpu_to_le16(this->read_word(mtd));
 		if (this->badblockpos & 0x1)
 			bad >>= 1;
 		if ((bad & 0xFF) != 0xff)
 			res = 1;
 	} else {
-		this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos, page & this->pagemask);
+		this->cmdfunc (mtd, NAND_CMD_READOOB, this->badblockpos, page);
 		if (this->read_byte(mtd) != 0xff)
 			res = 1;
 	}
diff --git a/drivers/nand/nand_ecc.c b/drivers/nand/nand_ecc.c
index f33be96..90274e6 100644
--- a/drivers/nand/nand_ecc.c
+++ b/drivers/nand/nand_ecc.c
@@ -40,6 +40,13 @@
 #if (CONFIG_COMMANDS & CFG_CMD_NAND) && !defined(CFG_NAND_LEGACY)
 
 #include<linux/mtd/mtd.h>
+
+/*
+ * NAND-SPL has no sofware ECC for now, so don't include nand_calculate_ecc(),
+ * only nand_correct_data() is needed
+ */
+
+#ifndef CONFIG_NAND_SPL
 /*
  * Pre-calculated 256-way 1 byte column parity
  */
@@ -62,90 +69,75 @@ static const u_char nand_ecc_precalc_table[] = {
 	0x00, 0x55, 0x56, 0x03, 0x59, 0x0c, 0x0f, 0x5a, 0x5a, 0x0f, 0x0c, 0x59, 0x03, 0x56, 0x55, 0x00
 };
 
-
-/**
- * nand_trans_result - [GENERIC] create non-inverted ECC
- * @reg2:	line parity reg 2
- * @reg3:	line parity reg 3
- * @ecc_code:	ecc
- *
- * Creates non-inverted ECC code from line parity
- */
-static void nand_trans_result(u_char reg2, u_char reg3,
-	u_char *ecc_code)
-{
-	u_char a, b, i, tmp1, tmp2;
-
-	/* Initialize variables */
-	a = b = 0x80;
-	tmp1 = tmp2 = 0;
-
-	/* Calculate first ECC byte */
-	for (i = 0; i < 4; i++) {
-		if (reg3 & a)		/* LP15,13,11,9 --> ecc_code[0] */
-			tmp1 |= b;
-		b >>= 1;
-		if (reg2 & a)		/* LP14,12,10,8 --> ecc_code[0] */
-			tmp1 |= b;
-		b >>= 1;
-		a >>= 1;
-	}
-
-	/* Calculate second ECC byte */
-	b = 0x80;
-	for (i = 0; i < 4; i++) {
-		if (reg3 & a)		/* LP7,5,3,1 --> ecc_code[1] */
-			tmp2 |= b;
-		b >>= 1;
-		if (reg2 & a)		/* LP6,4,2,0 --> ecc_code[1] */
-			tmp2 |= b;
-		b >>= 1;
-		a >>= 1;
-	}
-
-	/* Store two of the ECC bytes */
-	ecc_code[0] = tmp1;
-	ecc_code[1] = tmp2;
-}
-
 /**
- * nand_calculate_ecc - [NAND Interface] Calculate 3 byte ECC code for 256 byte block
+ * nand_calculate_ecc - [NAND Interface] Calculate 3-byte ECC for 256-byte block
  * @mtd:	MTD block structure
  * @dat:	raw data
  * @ecc_code:	buffer for ECC
  */
-int nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, u_char *ecc_code)
+int nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat,
+		       u_char *ecc_code)
 {
-	u_char idx, reg1, reg2, reg3;
-	int j;
+	uint8_t idx, reg1, reg2, reg3, tmp1, tmp2;
+	int i;
 
 	/* Initialize variables */
 	reg1 = reg2 = reg3 = 0;
-	ecc_code[0] = ecc_code[1] = ecc_code[2] = 0;
 
 	/* Build up column parity */
-	for(j = 0; j < 256; j++) {
-
+	for(i = 0; i < 256; i++) {
 		/* Get CP0 - CP5 from table */
-		idx = nand_ecc_precalc_table[dat[j]];
+		idx = nand_ecc_precalc_table[*dat++];
 		reg1 ^= (idx & 0x3f);
 
 		/* All bit XOR = 1 ? */
 		if (idx & 0x40) {
-			reg3 ^= (u_char) j;
-			reg2 ^= ~((u_char) j);
+			reg3 ^= (uint8_t) i;
+			reg2 ^= ~((uint8_t) i);
 		}
 	}
 
 	/* Create non-inverted ECC code from line parity */
-	nand_trans_result(reg2, reg3, ecc_code);
+	tmp1  = (reg3 & 0x80) >> 0; /* B7 -> B7 */
+	tmp1 |= (reg2 & 0x80) >> 1; /* B7 -> B6 */
+	tmp1 |= (reg3 & 0x40) >> 1; /* B6 -> B5 */
+	tmp1 |= (reg2 & 0x40) >> 2; /* B6 -> B4 */
+	tmp1 |= (reg3 & 0x20) >> 2; /* B5 -> B3 */
+	tmp1 |= (reg2 & 0x20) >> 3; /* B5 -> B2 */
+	tmp1 |= (reg3 & 0x10) >> 3; /* B4 -> B1 */
+	tmp1 |= (reg2 & 0x10) >> 4; /* B4 -> B0 */
+
+	tmp2  = (reg3 & 0x08) << 4; /* B3 -> B7 */
+	tmp2 |= (reg2 & 0x08) << 3; /* B3 -> B6 */
+	tmp2 |= (reg3 & 0x04) << 3; /* B2 -> B5 */
+	tmp2 |= (reg2 & 0x04) << 2; /* B2 -> B4 */
+	tmp2 |= (reg3 & 0x02) << 2; /* B1 -> B3 */
+	tmp2 |= (reg2 & 0x02) << 1; /* B1 -> B2 */
+	tmp2 |= (reg3 & 0x01) << 1; /* B0 -> B1 */
+	tmp2 |= (reg2 & 0x01) << 0; /* B7 -> B0 */
 
 	/* Calculate final ECC code */
-	ecc_code[0] = ~ecc_code[0];
-	ecc_code[1] = ~ecc_code[1];
+#ifdef CONFIG_MTD_NAND_ECC_SMC
+	ecc_code[0] = ~tmp2;
+	ecc_code[1] = ~tmp1;
+#else
+	ecc_code[0] = ~tmp1;
+	ecc_code[1] = ~tmp2;
+#endif
 	ecc_code[2] = ((~reg1) << 2) | 0x03;
+
 	return 0;
 }
+#endif /* CONFIG_NAND_SPL */
+
+static inline int countbits(uint32_t byte)
+{
+	int res = 0;
+
+	for (;byte; byte >>= 1)
+		res += byte & 0x01;
+	return res;
+}
 
 /**
  * nand_correct_data - [NAND Interface] Detect and correct bit error(s)
@@ -156,88 +148,52 @@ int nand_calculate_ecc(struct mtd_info *mtd, const u_char *dat, u_char *ecc_code
  *
  * Detect and correct a 1 bit error for 256 byte block
  */
-int nand_correct_data(struct mtd_info *mtd, u_char *dat, u_char *read_ecc, u_char *calc_ecc)
+int nand_correct_data(struct mtd_info *mtd, u_char *dat,
+		      u_char *read_ecc, u_char *calc_ecc)
 {
-	u_char a, b, c, d1, d2, d3, add, bit, i;
+	uint8_t s0, s1, s2;
+
+#ifdef CONFIG_MTD_NAND_ECC_SMC
+	s0 = calc_ecc[0] ^ read_ecc[0];
+	s1 = calc_ecc[1] ^ read_ecc[1];
+	s2 = calc_ecc[2] ^ read_ecc[2];
+#else
+	s1 = calc_ecc[0] ^ read_ecc[0];
+	s0 = calc_ecc[1] ^ read_ecc[1];
+	s2 = calc_ecc[2] ^ read_ecc[2];
+#endif
+	if ((s0 | s1 | s2) == 0)
+		return 0;
 
-	/* Do error detection */
-	d1 = calc_ecc[0] ^ read_ecc[0];
-	d2 = calc_ecc[1] ^ read_ecc[1];
-	d3 = calc_ecc[2] ^ read_ecc[2];
+	/* Check for a single bit error */
+	if( ((s0 ^ (s0 >> 1)) & 0x55) == 0x55 &&
+	    ((s1 ^ (s1 >> 1)) & 0x55) == 0x55 &&
+	    ((s2 ^ (s2 >> 1)) & 0x54) == 0x54) {
 
-	if ((d1 | d2 | d3) == 0) {
-		/* No errors */
-		return 0;
-	}
-	else {
-		a = (d1 ^ (d1 >> 1)) & 0x55;
-		b = (d2 ^ (d2 >> 1)) & 0x55;
-		c = (d3 ^ (d3 >> 1)) & 0x54;
-
-		/* Found and will correct single bit error in the data */
-		if ((a == 0x55) && (b == 0x55) && (c == 0x54)) {
-			c = 0x80;
-			add = 0;
-			a = 0x80;
-			for (i=0; i<4; i++) {
-				if (d1 & c)
-					add |= a;
-				c >>= 2;
-				a >>= 1;
-			}
-			c = 0x80;
-			for (i=0; i<4; i++) {
-				if (d2 & c)
-					add |= a;
-				c >>= 2;
-				a >>= 1;
-			}
-			bit = 0;
-			b = 0x04;
-			c = 0x80;
-			for (i=0; i<3; i++) {
-				if (d3 & c)
-					bit |= b;
-				c >>= 2;
-				b >>= 1;
-			}
-			b = 0x01;
-			a = dat[add];
-			a ^= (b << bit);
-			dat[add] = a;
-			return 1;
-		} else {
-			i = 0;
-			while (d1) {
-				if (d1 & 0x01)
-					++i;
-				d1 >>= 1;
-			}
-			while (d2) {
-				if (d2 & 0x01)
-					++i;
-				d2 >>= 1;
-			}
-			while (d3) {
-				if (d3 & 0x01)
-					++i;
-				d3 >>= 1;
-			}
-			if (i == 1) {
-				/* ECC Code Error Correction */
-				read_ecc[0] = calc_ecc[0];
-				read_ecc[1] = calc_ecc[1];
-				read_ecc[2] = calc_ecc[2];
-				return 2;
-			}
-			else {
-				/* Uncorrectable Error */
-				return -1;
-			}
-		}
+		uint32_t byteoffs, bitnum;
+
+		byteoffs = (s1 << 0) & 0x80;
+		byteoffs |= (s1 << 1) & 0x40;
+		byteoffs |= (s1 << 2) & 0x20;
+		byteoffs |= (s1 << 3) & 0x10;
+
+		byteoffs |= (s0 >> 4) & 0x08;
+		byteoffs |= (s0 >> 3) & 0x04;
+		byteoffs |= (s0 >> 2) & 0x02;
+		byteoffs |= (s0 >> 1) & 0x01;
+
+		bitnum = (s2 >> 5) & 0x04;
+		bitnum |= (s2 >> 4) & 0x02;
+		bitnum |= (s2 >> 3) & 0x01;
+
+		dat[byteoffs] ^= (1 << bitnum);
+
+		return 1;
 	}
 
-	/* Should never happen */
+	if(countbits(s0 | ((uint32_t)s1 << 8) | ((uint32_t)s2 <<16)) == 1)
+		return 1;
+
 	return -1;
 }
 
diff --git a/drivers/pci_auto.c b/drivers/pci_auto.c
index 9691675..f170c2d 100644
--- a/drivers/pci_auto.c
+++ b/drivers/pci_auto.c
@@ -34,7 +34,12 @@
 
 void pciauto_region_init(struct pci_region* res)
 {
-	res->bus_lower = res->bus_start;
+	/*
+	 * Avoid allocating PCI resources from address 0 -- this is illegal
+	 * according to PCI 2.1 and moreover, this is known to cause Linux IDE
+	 * drivers to fail. Use a reasonable starting value of 0x1000 instead.
+	 */
+	res->bus_lower = res->bus_start ? res->bus_start : 0x1000;
 }
 
 void pciauto_region_align(struct pci_region *res, unsigned long size)
diff --git a/drivers/smc91111.c b/drivers/smc91111.c
index f91e4b9..8061f12 100644
--- a/drivers/smc91111.c
+++ b/drivers/smc91111.c
@@ -1538,9 +1538,9 @@ int eth_send(volatile void *packet, int length) {
 int smc_get_ethaddr (bd_t * bd)
 {
 	int env_size, rom_valid, env_present = 0, reg;
-	char *s = NULL, *e, *v_mac, es[] = "11:22:33:44:55:66";
+	char *s = NULL, *e, es[] = "11:22:33:44:55:66";
 	char s_env_mac[64];
-	uchar v_env_mac[6], v_rom_mac[6];
+	uchar v_env_mac[6], v_rom_mac[6], *v_mac;
 
 	env_size = getenv_r ("ethaddr", s_env_mac, sizeof (s_env_mac));
 	if ((env_size > 0) && (env_size < sizeof (es))) {	/* exit if env is bad */
@@ -1563,7 +1563,7 @@ int smc_get_ethaddr (bd_t * bd)
 
 	if (!env_present) {	/* if NO env */
 		if (rom_valid) {	/* but ROM is valid */
-			v_mac = (char *)v_rom_mac;
+			v_mac = v_rom_mac;
 			sprintf (s_env_mac, "%02X:%02X:%02X:%02X:%02X:%02X",
 				 v_mac[0], v_mac[1], v_mac[2], v_mac[3],
 				 v_mac[4], v_mac[5]);
@@ -1573,7 +1573,7 @@ int smc_get_ethaddr (bd_t * bd)
 			return (-1);
 		}
 	} else {		/* good env, don't care ROM */
-		v_mac = (char *)v_env_mac;	/* always use a good env over a ROM */
+		v_mac = v_env_mac;	/* always use a good env over a ROM */
 	}
 
 	if (env_present && rom_valid) { /* if both env and ROM are good */
diff --git a/drivers/systemace.c b/drivers/systemace.c
index 3848d9c..7d82c27 100644
--- a/drivers/systemace.c
+++ b/drivers/systemace.c
@@ -211,10 +211,16 @@ static unsigned long systemace_read(int dev, unsigned long start,
 		/* Write sector count | ReadMemCardData. */
 		ace_writew((trans & 0xff) | 0x0300, 0x14);
 
+/*
+ * For FPGA configuration via SystemACE is reset unacceptable
+ * CFGDONE bit in STATUSREG is not set to 1.
+ */
+#ifndef SYSTEMACE_CONFIG_FPGA
 		/* Reset the configruation controller */
 		val = ace_readw(0x18);
 		val |= 0x0080;
 		ace_writew(val, 0x18);
+#endif
 
 		retry = trans * 16;
 		while (retry > 0) {
diff --git a/drivers/tsec.c b/drivers/tsec.c
index 3f11eb0..b418773 100644
--- a/drivers/tsec.c
+++ b/drivers/tsec.c
@@ -5,7 +5,7 @@
  * terms of the GNU Public License, Version 2, incorporated
  * herein by reference.
  *
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2004, 2007 Freescale Semiconductor, Inc.
  * (C) Copyright 2003, Motorola, Inc.
  * author Andy Fleming
  *
@@ -66,7 +66,11 @@ struct tsec_info_struct {
  */
 static struct tsec_info_struct tsec_info[] = {
 #if defined(CONFIG_MPC85XX_TSEC1) || defined(CONFIG_MPC83XX_TSEC1)
+#if defined(CONFIG_MPC8544DS)
+	{TSEC1_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC1_PHYIDX},
+#else
 	{TSEC1_PHY_ADDR, TSEC_GIGABIT, TSEC1_PHYIDX},
+#endif
 #elif defined(CONFIG_MPC86XX_TSEC1)
 	{TSEC1_PHY_ADDR, TSEC_GIGABIT | TSEC_REDUCED, TSEC1_PHYIDX},
 #else
@@ -381,6 +385,76 @@ uint mii_parse_sr(uint mii_reg, struct tsec_private * priv)
 	return 0;
 }
 
+/* Generic function which updates the speed and duplex.  If
+ * autonegotiation is enabled, it uses the AND of the link
+ * partner's advertised capabilities and our advertised
+ * capabilities.  If autonegotiation is disabled, we use the
+ * appropriate bits in the control register.
+ *
+ * Stolen from Linux's mii.c and phy_device.c
+ */
+uint mii_parse_link(uint mii_reg, struct tsec_private *priv)
+{
+	/* We're using autonegotiation */
+	if (mii_reg & PHY_BMSR_AUTN_ABLE) {
+		uint lpa = 0;
+		uint gblpa = 0;
+
+		/* Check for gigabit capability */
+		if (mii_reg & PHY_BMSR_EXT) {
+			/* We want a list of states supported by
+			 * both PHYs in the link
+			 */
+			gblpa = read_phy_reg(priv, PHY_1000BTSR);
+			gblpa &= read_phy_reg(priv, PHY_1000BTCR) << 2;
+		}
+
+		/* Set the baseline so we only have to set them
+		 * if they're different
+		 */
+		priv->speed = 10;
+		priv->duplexity = 0;
+
+		/* Check the gigabit fields */
+		if (gblpa & (PHY_1000BTSR_1000FD | PHY_1000BTSR_1000HD)) {
+			priv->speed = 1000;
+
+			if (gblpa & PHY_1000BTSR_1000FD)
+				priv->duplexity = 1;
+
+			/* We're done! */
+			return 0;
+		}
+
+		lpa = read_phy_reg(priv, PHY_ANAR);
+		lpa &= read_phy_reg(priv, PHY_ANLPAR);
+
+		if (lpa & (PHY_ANLPAR_TXFD | PHY_ANLPAR_TX)) {
+			priv->speed = 100;
+
+			if (lpa & PHY_ANLPAR_TXFD)
+				priv->duplexity = 1;
+
+		} else if (lpa & PHY_ANLPAR_10FD)
+			priv->duplexity = 1;
+	} else {
+		uint bmcr = read_phy_reg(priv, PHY_BMCR);
+
+		priv->speed = 10;
+		priv->duplexity = 0;
+
+		if (bmcr & PHY_BMCR_DPLX)
+			priv->duplexity = 1;
+
+		if (bmcr & PHY_BMCR_1000_MBPS)
+			priv->speed = 1000;
+		else if (bmcr & PHY_BMCR_100_MBPS)
+			priv->speed = 100;
+	}
+
+	return 0;
+}
+
 /*
  * Parse the BCM54xx status register for speed and duplex information.
  * The linux sungem_phy has this information, but in a table format.
@@ -718,6 +792,7 @@ static void startup_tsec(struct eth_device *dev)
 	/* Start up the PHY */
 	if(priv->phyinfo)
 		phy_run_commands(priv, priv->phyinfo->startup);
+
 	adjust_link(dev);
 
 	/* Enable Transmit and Receive */
@@ -1088,6 +1163,27 @@ struct phy_info phy_info_dm9161 = {
 			   {miim_end,}
 			   },
 };
+/* a generic flavor.  */
+struct phy_info phy_info_generic =  {
+	0,
+	"Unknown/Generic PHY",
+	32,
+	(struct phy_cmd[]) { /* config */
+		{PHY_BMCR, PHY_BMCR_RESET, NULL},
+		{PHY_BMCR, PHY_BMCR_AUTON|PHY_BMCR_RST_NEG, NULL},
+		{miim_end,}
+	},
+	(struct phy_cmd[]) { /* startup */
+		{PHY_BMSR, miim_read, NULL},
+		{PHY_BMSR, miim_read, &mii_parse_sr},
+		{PHY_BMSR, miim_read, &mii_parse_link},
+		{miim_end,}
+	},
+	(struct phy_cmd[]) { /* shutdown */
+		{miim_end,}
+	}
+};
+
 
 uint mii_parse_lxt971_sr2(uint mii_reg, struct tsec_private *priv)
 {
@@ -1203,6 +1299,7 @@ struct phy_info *phy_info[] = {
 	&phy_info_lxt971,
 	&phy_info_VSC8244,
 	&phy_info_dp83865,
+	&phy_info_generic,
 	NULL
 };
 
diff --git a/drivers/tsec.h b/drivers/tsec.h
index 422bc66..7bf3dee 100644
--- a/drivers/tsec.h
+++ b/drivers/tsec.h
@@ -7,7 +7,7 @@
  *  terms of the GNU Public License, Version 2, incorporated
  *  herein by reference.
  *
- * Copyright 2004 Freescale Semiconductor.
+ * Copyright 2004, 2007 Freescale Semiconductor, Inc.
  * (C) Copyright 2003, Motorola, Inc.
  * maintained by Xianghua Xiao (x.xiao@motorola.com)
  * author Andy Fleming
@@ -65,6 +65,7 @@
 #define ECNTRL_INIT_SETTINGS	0x00001000
 #define ECNTRL_TBI_MODE         0x00000020
 #define ECNTRL_R100		0x00000008
+#define ECNTRL_SGMII_MODE	0x00000002
 
 #define miim_end -2
 #define miim_read -1