lpc32xx: add LPC32xx SSP support (SPI mode)

Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Signed-off-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>

2 files changed, 145 insertions, 0 deletions

diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index edbd520..ce6f1cc 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -32,6 +32,7 @@ obj-$(CONFIG_EXYNOS_SPI) += exynos_spi.o
 obj-$(CONFIG_FTSSP010_SPI) += ftssp010_spi.o
 obj-$(CONFIG_ICH_SPI) +=  ich.o
 obj-$(CONFIG_KIRKWOOD_SPI) += kirkwood_spi.o
+obj-$(CONFIG_LPC32XX_SSP) += lpc32xx_ssp.o
 obj-$(CONFIG_MPC52XX_SPI) += mpc52xx_spi.o
 obj-$(CONFIG_MPC8XXX_SPI) += mpc8xxx_spi.o
 obj-$(CONFIG_MXC_SPI) += mxc_spi.o
diff --git a/drivers/spi/lpc32xx_ssp.c b/drivers/spi/lpc32xx_ssp.c
new file mode 100644
index 0000000..c5b766c
--- /dev/null
+++ b/drivers/spi/lpc32xx_ssp.c
@@ -0,0 +1,144 @@
+/*
+ * LPC32xx SSP interface (SPI mode)
+ *
+ * (C) Copyright 2014  DENX Software Engineering GmbH
+ * Written-by: Albert ARIBAUD <albert.aribaud@3adev.fr>
+ *
+ * SPDX-License-Identifier:     GPL-2.0+
+ */
+
+#include <common.h>
+#include <linux/compat.h>
+#include <asm/io.h>
+#include <malloc.h>
+#include <spi.h>
+#include <asm/arch/clk.h>
+
+/* SSP chip registers */
+struct ssp_regs {
+	u32 cr0;
+	u32 cr1;
+	u32 data;
+	u32 sr;
+	u32 cpsr;
+	u32 imsc;
+	u32 ris;
+	u32 mis;
+	u32 icr;
+	u32 dmacr;
+};
+
+/* CR1 register defines  */
+#define SSP_CR1_SSP_ENABLE 0x0002
+
+/* SR register defines  */
+#define SSP_SR_TNF 0x0002
+/* SSP status RX FIFO not empty bit */
+#define SSP_SR_RNE 0x0004
+
+/* lpc32xx spi slave */
+struct lpc32xx_spi_slave {
+	struct spi_slave slave;
+	struct ssp_regs *regs;
+};
+
+static inline struct lpc32xx_spi_slave *to_lpc32xx_spi_slave(
+	struct spi_slave *slave)
+{
+	return container_of(slave, struct lpc32xx_spi_slave, slave);
+}
+
+/* spi_init is called during boot when CONFIG_CMD_SPI is defined */
+void spi_init(void)
+{
+	/*
+	 *  nothing to do: clocking was enabled in lpc32xx_ssp_enable()
+	 * and configuration will be done in spi_setup_slave()
+	*/
+}
+
+/* the following is called in sequence by do_spi_xfer() */
+
+struct spi_slave *spi_setup_slave(uint bus, uint cs, uint max_hz, uint mode)
+{
+	struct lpc32xx_spi_slave *lslave;
+
+	/* we only set up SSP0 for now, so ignore bus */
+
+	if (mode & SPI_3WIRE) {
+		error("3-wire mode not supported");
+		return NULL;
+	}
+
+	if (mode & SPI_SLAVE) {
+		error("slave mode not supported\n");
+		return NULL;
+	}
+
+	if (mode & SPI_PREAMBLE) {
+		error("preamble byte skipping not supported\n");
+		return NULL;
+	}
+
+	lslave = spi_alloc_slave(struct lpc32xx_spi_slave, bus, cs);
+	if (!lslave) {
+		printf("SPI_error: Fail to allocate lpc32xx_spi_slave\n");
+		return NULL;
+	}
+
+	lslave->regs = (struct ssp_regs *)SSP0_BASE;
+
+	/*
+	 * 8 bit frame, SPI fmt, 500kbps -> clock divider is 26.
+	 * Set SCR to 0 and CPSDVSR to 26.
+	 */
+
+	writel(0x7, &lslave->regs->cr0); /* 8-bit chunks, SPI, 1 clk/bit */
+	writel(26, &lslave->regs->cpsr); /* SSP clock = HCLK/26 = 500kbps */
+	writel(0, &lslave->regs->imsc); /* do not raise any interrupts */
+	writel(0, &lslave->regs->icr); /* clear any pending interrupt */
+	writel(0, &lslave->regs->dmacr); /* do not do DMAs */
+	writel(SSP_CR1_SSP_ENABLE, &lslave->regs->cr1); /* enable SSP0 */
+	return &lslave->slave;
+}
+
+void spi_free_slave(struct spi_slave *slave)
+{
+	struct lpc32xx_spi_slave *lslave = to_lpc32xx_spi_slave(slave);
+
+	debug("(lpc32xx) spi_free_slave: 0x%08x\n", (u32)lslave);
+	free(lslave);
+}
+
+int spi_claim_bus(struct spi_slave *slave)
+{
+	/* only one bus and slave so far, always available */
+	return 0;
+}
+
+int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
+	const void *dout, void *din, unsigned long flags)
+{
+	struct lpc32xx_spi_slave *lslave = to_lpc32xx_spi_slave(slave);
+	int bytelen = bitlen >> 3;
+	int idx_out = 0;
+	int idx_in = 0;
+	int start_time;
+
+	start_time = get_timer(0);
+	while ((idx_out < bytelen) || (idx_in < bytelen)) {
+		int status = readl(&lslave->regs->sr);
+		if ((idx_out < bytelen) && (status & SSP_SR_TNF))
+			writel(((u8 *)dout)[idx_out++], &lslave->regs->data);
+		if ((idx_in < bytelen) && (status & status & SSP_SR_RNE))
+			((u8 *)din)[idx_in++] = readl(&lslave->regs->data);
+		if (get_timer(start_time) >= CONFIG_LPC32XX_SSP_TIMEOUT)
+			return -1;
+	}
+	return 0;
+}
+
+void spi_release_bus(struct spi_slave *slave)
+{
+	/* do nothing */
+}