summaryrefslogtreecommitdiff
path: root/drivers/rtl8139.c
diff options
context:
space:
mode:
authorwdenk <wdenk>2004-01-02 16:05:07 +0000
committerwdenk <wdenk>2004-01-02 16:05:07 +0000
commitb6e4c4033c4f889c452c511d38c77808c67f9cf7 (patch)
tree73a39833805f4cf47588dd1616a1b479ab58a418 /drivers/rtl8139.c
parent63f3491242df8e6bd1b5df7296f28959989e2eaf (diff)
downloadu-boot-imx-b6e4c4033c4f889c452c511d38c77808c67f9cf7.zip
u-boot-imx-b6e4c4033c4f889c452c511d38c77808c67f9cf7.tar.gz
u-boot-imx-b6e4c4033c4f889c452c511d38c77808c67f9cf7.tar.bz2
* Patch by Denis Peter, 8 Dec 2003
- add support for the PATI board (MPC555) - add SPI support for the MPC5xx * Patch by Anders Larsen, 08 Dec 2003: add configuration options CONFIG_SERIAL_TAG and CONFIG_REVISION_TAG to pass ATAG_SERIAL and ATAG_REVISION, resp., to the ARM target; cleanup some redundand #defines
Diffstat (limited to 'drivers/rtl8139.c')
-rw-r--r--drivers/rtl8139.c56
1 files changed, 27 insertions, 29 deletions
diff --git a/drivers/rtl8139.c b/drivers/rtl8139.c
index 5b14e71..b9e4a8d 100644
--- a/drivers/rtl8139.c
+++ b/drivers/rtl8139.c
@@ -44,7 +44,7 @@
which reserves the ranges 0x00000-0x10000 and 0x98000-0xA0000. My
interpretation of this "reserved" is that Etherboot may do whatever it
likes, as long as its environment is kept intact (like the BIOS
- variables). Hopefully fixed rtl_poll() once and for all. The symptoms
+ variables). Hopefully fixed rtl_poll() once and for all. The symptoms
were that if Etherboot was left at the boot menu for several minutes, the
first eth_poll failed. Seems like I am the only person who does this.
First of all I fixed the debugging code and then set out for a long bug
@@ -53,18 +53,18 @@
driver and even the FreeBSD driver (what a piece of crap!) - and
eventually spotted the nasty thing: the transmit routine was acknowledging
each and every interrupt pending, including the RxOverrun and RxFIFIOver
- interrupts. This confused the RTL8139 thoroughly. It destroyed the
+ interrupts. This confused the RTL8139 thoroughly. It destroyed the
Rx ring contents by dumping the 2K FIFO contents right where we wanted to
get the next packet. Oh well, what fun.
- 18 Jan 2000 mdc@thinguin.org (Marty Connor)
+ 18 Jan 2000 mdc@thinguin.org (Marty Connor)
Drastically simplified error handling. Basically, if any error
in transmission or reception occurs, the card is reset.
Also, pointed all transmit descriptors to the same buffer to
- save buffer space. This should decrease driver size and avoid
+ save buffer space. This should decrease driver size and avoid
corruption because of exceeding 32K during runtime.
- 28 Jul 1999 (Matthias Meixner - meixner@rbg.informatik.tu-darmstadt.de)
+ 28 Jul 1999 (Matthias Meixner - meixner@rbg.informatik.tu-darmstadt.de)
rtl_poll was quite broken: it used the RxOK interrupt flag instead
of the RxBufferEmpty flag which often resulted in very bad
transmission performace - below 1kBytes/s.
@@ -77,10 +77,6 @@
#include <asm/io.h>
#include <pci.h>
-#ifdef __MIPS__
-static unsigned long mips_io_port_base = 0;
-#endif
-
#if (CONFIG_COMMANDS & CFG_CMD_NET) && defined(CONFIG_NET_MULTI) && \
defined(CONFIG_RTL8139)
@@ -95,11 +91,11 @@ static unsigned long mips_io_port_base = 0;
/* PCI Tuning Parameters
Threshold is bytes transferred to chip before transmission starts. */
-#define TX_FIFO_THRESH 256 /* In bytes, rounded down to 32 byte units. */
-#define RX_FIFO_THRESH 4 /* Rx buffer level before first PCI xfer. */
-#define RX_DMA_BURST 4 /* Maximum PCI burst, '4' is 256 bytes */
-#define TX_DMA_BURST 4 /* Calculate as 16<<val. */
-#define NUM_TX_DESC 4 /* Number of Tx descriptor registers. */
+#define TX_FIFO_THRESH 256 /* In bytes, rounded down to 32 byte units. */
+#define RX_FIFO_THRESH 4 /* Rx buffer level before first PCI xfer. */
+#define RX_DMA_BURST 4 /* Maximum PCI burst, '4' is 256 bytes */
+#define TX_DMA_BURST 4 /* Calculate as 16<<val. */
+#define NUM_TX_DESC 4 /* Number of Tx descriptor registers. */
#define TX_BUF_SIZE ETH_FRAME_LEN /* FCS is added by the chip */
#define RX_BUF_LEN_IDX 0 /* 0, 1, 2 is allowed - 8,16,32K rx buffer */
#define RX_BUF_LEN (8192 << RX_BUF_LEN_IDX)
@@ -108,8 +104,8 @@ static unsigned long mips_io_port_base = 0;
#undef DEBUG_RX
#define currticks() get_timer(0)
-#define bus_to_phys(a) pci_mem_to_phys((pci_dev_t)dev->priv, a)
-#define phys_to_bus(a) pci_phys_to_mem((pci_dev_t)dev->priv, a)
+#define bus_to_phys(a) pci_mem_to_phys((pci_dev_t)dev->priv, a)
+#define phys_to_bus(a) pci_phys_to_mem((pci_dev_t)dev->priv, a)
/* Symbolic offsets to registers. */
enum RTL8139_registers {
@@ -276,12 +272,12 @@ static int rtl8139_probe(struct eth_device *dev, bd_t *bis)
/* Serial EEPROM section. */
/* EEPROM_Ctrl bits. */
-#define EE_SHIFT_CLK 0x04 /* EEPROM shift clock. */
-#define EE_CS 0x08 /* EEPROM chip select. */
-#define EE_DATA_WRITE 0x02 /* EEPROM chip data in. */
-#define EE_WRITE_0 0x00
-#define EE_WRITE_1 0x02
-#define EE_DATA_READ 0x01 /* EEPROM chip data out. */
+#define EE_SHIFT_CLK 0x04 /* EEPROM shift clock. */
+#define EE_CS 0x08 /* EEPROM chip select. */
+#define EE_DATA_WRITE 0x02 /* EEPROM chip data in. */
+#define EE_WRITE_0 0x00
+#define EE_WRITE_1 0x02
+#define EE_DATA_READ 0x01 /* EEPROM chip data out. */
#define EE_ENB (0x80 | EE_CS)
/*
@@ -289,12 +285,12 @@ static int rtl8139_probe(struct eth_device *dev, bd_t *bis)
No extra delay is needed with 33Mhz PCI, but 66Mhz may change this.
*/
-#define eeprom_delay() inl(ee_addr)
+#define eeprom_delay() inl(ee_addr)
/* The EEPROM commands include the alway-set leading bit. */
-#define EE_WRITE_CMD (5)
-#define EE_READ_CMD (6)
-#define EE_ERASE_CMD (7)
+#define EE_WRITE_CMD (5)
+#define EE_READ_CMD (6)
+#define EE_ERASE_CMD (7)
static int read_eeprom(int location, int addr_len)
{
@@ -390,7 +386,7 @@ static void rtl_reset(struct eth_device *dev)
/* If we add multicast support, the MAR0 register would have to be
* initialized to 0xffffffffffffffff (two 32 bit accesses). Etherboot
- * only needs broadcast (for ARP/RARP/BOOTP/DHCP) and unicast. */
+ * only needs broadcast (for ARP/RARP/BOOTP/DHCP) and unicast. */
outb(CmdRxEnb | CmdTxEnb, ioaddr + ChipCmd);
@@ -436,7 +432,7 @@ static int rtl_transmit(struct eth_device *dev, volatile void *packet, int lengt
status = inw(ioaddr + IntrStatus);
/* Only acknlowledge interrupt sources we can properly handle
* here - the RxOverflow/RxFIFOOver MUST be handled in the
- * rtl_poll() function. */
+ * rtl_poll() function. */
outw(status & (TxOK | TxErr | PCIErr), ioaddr + IntrStatus);
if ((status & (TxOK | TxErr | PCIErr)) != 0) break;
} while (currticks() < to);
@@ -490,7 +486,7 @@ static int rtl_poll(struct eth_device *dev)
if ((rx_status & (RxBadSymbol|RxRunt|RxTooLong|RxCRCErr|RxBadAlign)) ||
(rx_size < ETH_ZLEN) || (rx_size > ETH_FRAME_LEN + 4)) {
printf("rx error %hX\n", rx_status);
- rtl_reset(dev); /* this clears all interrupts still pending */
+ rtl_reset(dev); /* this clears all interrupts still pending */
return 0;
}
@@ -527,6 +523,8 @@ static void rtl_disable(struct eth_device *dev)
{
int i;
+ ioaddr = dev->iobase;
+
/* reset the chip */
outb(CmdReset, ioaddr + ChipCmd);