Merge branch 'master' of git://git.denx.de/u-boot-arm

1 files changed, 442 insertions, 0 deletions

diff --git a/drivers/i2c/s3c24x0_i2c.c b/drivers/i2c/s3c24x0_i2c.c
new file mode 100644
index 0000000..f0c1aa3
--- /dev/null
+++ b/drivers/i2c/s3c24x0_i2c.c
@@ -0,0 +1,442 @@
+/*
+ * (C) Copyright 2002
+ * David Mueller, ELSOFT AG, d.mueller@elsoft.ch
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/* This code should work for both the S3C2400 and the S3C2410
+ * as they seem to have the same I2C controller inside.
+ * The different address mapping is handled by the s3c24xx.h files below.
+ */
+
+#include <common.h>
+#if defined(CONFIG_S3C2400)
+#include <s3c2400.h>
+#elif defined(CONFIG_S3C2410)
+#include <s3c2410.h>
+#endif
+#include <i2c.h>
+
+#ifdef CONFIG_HARD_I2C
+
+#define	I2C_WRITE	0
+#define I2C_READ	1
+
+#define I2C_OK		0
+#define I2C_NOK		1
+#define I2C_NACK	2
+#define I2C_NOK_LA	3		/* Lost arbitration */
+#define I2C_NOK_TOUT	4		/* time out */
+
+#define I2CSTAT_BSY	0x20		/* Busy bit */
+#define I2CSTAT_NACK	0x01		/* Nack bit */
+#define I2CCON_IRPND	0x10		/* Interrupt pending bit */
+#define I2C_MODE_MT	0xC0		/* Master Transmit Mode */
+#define I2C_MODE_MR	0x80		/* Master Receive Mode */
+#define I2C_START_STOP	0x20		/* START / STOP */
+#define I2C_TXRX_ENA	0x10		/* I2C Tx/Rx enable */
+
+#define I2C_TIMEOUT 1			/* 1 second */
+
+
+static int GetI2CSDA(void)
+{
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
+#ifdef CONFIG_S3C2410
+	return (gpio->GPEDAT & 0x8000) >> 15;
+#endif
+#ifdef CONFIG_S3C2400
+	return (gpio->PGDAT & 0x0020) >> 5;
+#endif
+}
+
+#if 0
+static void SetI2CSDA(int x)
+{
+	rGPEDAT = (rGPEDAT & ~0x8000) | (x&1) << 15;
+}
+#endif
+
+static void SetI2CSCL(int x)
+{
+	S3C24X0_GPIO * const gpio = S3C24X0_GetBase_GPIO();
+
+#ifdef CONFIG_S3C2410
+	gpio->GPEDAT = (gpio->GPEDAT & ~0x4000) | (x&1) << 14;
+#endif
+#ifdef CONFIG_S3C2400
+	gpio->PGDAT = (gpio->PGDAT & ~0x0040) | (x&1) << 6;
+#endif
+}
+
+
+static int WaitForXfer (void)
+{
+	S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C ();
+	int i, status;
+
+	i = I2C_TIMEOUT * 10000;
+	status = i2c->IICCON;
+	while ((i > 0) && !(status & I2CCON_IRPND)) {
+		udelay (100);
+		status = i2c->IICCON;
+		i--;
+	}
+
+	return (status & I2CCON_IRPND) ? I2C_OK : I2C_NOK_TOUT;
+}
+
+static int IsACK (void)
+{
+	S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C ();
+
+	return (!(i2c->IICSTAT & I2CSTAT_NACK));
+}
+
+static void ReadWriteByte (void)
+{
+	S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C ();
+
+	i2c->IICCON &= ~I2CCON_IRPND;
+}
+
+void i2c_init (int speed, int slaveadd)
+{
+	S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C ();
+	S3C24X0_GPIO *const gpio = S3C24X0_GetBase_GPIO ();
+	ulong freq, pres = 16, div;
+	int i, status;
+
+	/* wait for some time to give previous transfer a chance to finish */
+
+	i = I2C_TIMEOUT * 1000;
+	status = i2c->IICSTAT;
+	while ((i > 0) && (status & I2CSTAT_BSY)) {
+		udelay (1000);
+		status = i2c->IICSTAT;
+		i--;
+	}
+
+	if ((status & I2CSTAT_BSY) || GetI2CSDA () == 0) {
+#ifdef CONFIG_S3C2410
+		ulong old_gpecon = gpio->GPECON;
+#endif
+#ifdef CONFIG_S3C2400
+		ulong old_gpecon = gpio->PGCON;
+#endif
+		/* bus still busy probably by (most) previously interrupted transfer */
+
+#ifdef CONFIG_S3C2410
+		/* set I2CSDA and I2CSCL (GPE15, GPE14) to GPIO */
+		gpio->GPECON = (gpio->GPECON & ~0xF0000000) | 0x10000000;
+#endif
+#ifdef CONFIG_S3C2400
+		/* set I2CSDA and I2CSCL (PG5, PG6) to GPIO */
+		gpio->PGCON = (gpio->PGCON & ~0x00003c00) | 0x00001000;
+#endif
+
+		/* toggle I2CSCL until bus idle */
+		SetI2CSCL (0);
+		udelay (1000);
+		i = 10;
+		while ((i > 0) && (GetI2CSDA () != 1)) {
+			SetI2CSCL (1);
+			udelay (1000);
+			SetI2CSCL (0);
+			udelay (1000);
+			i--;
+		}
+		SetI2CSCL (1);
+		udelay (1000);
+
+		/* restore pin functions */
+#ifdef CONFIG_S3C2410
+		gpio->GPECON = old_gpecon;
+#endif
+#ifdef CONFIG_S3C2400
+		gpio->PGCON = old_gpecon;
+#endif
+	}
+
+	/* calculate prescaler and divisor values */
+	freq = get_PCLK ();
+	if ((freq / pres / (16 + 1)) > speed)
+		/* set prescaler to 512 */
+		pres = 512;
+
+	div = 0;
+	while ((freq / pres / (div + 1)) > speed)
+		div++;
+
+	/* set prescaler, divisor according to freq, also set
+	 * ACKGEN, IRQ */
+	i2c->IICCON = (div & 0x0F) | 0xA0 | ((pres == 512) ? 0x40 : 0);
+
+	/* init to SLAVE REVEIVE and set slaveaddr */
+	i2c->IICSTAT = 0;
+	i2c->IICADD = slaveadd;
+	/* program Master Transmit (and implicit STOP) */
+	i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA;
+
+}
+
+/*
+ * cmd_type is 0 for write, 1 for read.
+ *
+ * addr_len can take any value from 0-255, it is only limited
+ * by the char, we could make it larger if needed. If it is
+ * 0 we skip the address write cycle.
+ */
+static
+int i2c_transfer (unsigned char cmd_type,
+		  unsigned char chip,
+		  unsigned char addr[],
+		  unsigned char addr_len,
+		  unsigned char data[], unsigned short data_len)
+{
+	S3C24X0_I2C *const i2c = S3C24X0_GetBase_I2C ();
+	int i, status, result;
+
+	if (data == 0 || data_len == 0) {
+		/*Don't support data transfer of no length or to address 0 */
+		printf ("i2c_transfer: bad call\n");
+		return I2C_NOK;
+	}
+
+	/* Check I2C bus idle */
+	i = I2C_TIMEOUT * 1000;
+	status = i2c->IICSTAT;
+	while ((i > 0) && (status & I2CSTAT_BSY)) {
+		udelay (1000);
+		status = i2c->IICSTAT;
+		i--;
+	}
+
+	if (status & I2CSTAT_BSY)
+		return I2C_NOK_TOUT;
+
+	i2c->IICCON |= 0x80;
+	result = I2C_OK;
+
+	switch (cmd_type) {
+	case I2C_WRITE:
+		if (addr && addr_len) {
+			i2c->IICDS = chip;
+			/* send START */
+			i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA | I2C_START_STOP;
+			i = 0;
+			while ((i < addr_len) && (result == I2C_OK)) {
+				result = WaitForXfer ();
+				i2c->IICDS = addr[i];
+				ReadWriteByte ();
+				i++;
+			}
+			i = 0;
+			while ((i < data_len) && (result == I2C_OK)) {
+				result = WaitForXfer ();
+				i2c->IICDS = data[i];
+				ReadWriteByte ();
+				i++;
+			}
+		} else {
+			i2c->IICDS = chip;
+			/* send START */
+			i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA | I2C_START_STOP;
+			i = 0;
+			while ((i < data_len) && (result = I2C_OK)) {
+				result = WaitForXfer ();
+				i2c->IICDS = data[i];
+				ReadWriteByte ();
+				i++;
+			}
+		}
+
+		if (result == I2C_OK)
+			result = WaitForXfer ();
+
+		/* send STOP */
+		i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA;
+		ReadWriteByte ();
+		break;
+
+	case I2C_READ:
+		if (addr && addr_len) {
+			i2c->IICSTAT = I2C_MODE_MT | I2C_TXRX_ENA;
+			i2c->IICDS = chip;
+			/* send START */
+			i2c->IICSTAT |= I2C_START_STOP;
+			result = WaitForXfer ();
+			if (IsACK ()) {
+				i = 0;
+				while ((i < addr_len) && (result == I2C_OK)) {
+					i2c->IICDS = addr[i];
+					ReadWriteByte ();
+					result = WaitForXfer ();
+					i++;
+				}
+
+				i2c->IICDS = chip;
+				/* resend START */
+				i2c->IICSTAT =  I2C_MODE_MR | I2C_TXRX_ENA |
+						I2C_START_STOP;
+				ReadWriteByte ();
+				result = WaitForXfer ();
+				i = 0;
+				while ((i < data_len) && (result == I2C_OK)) {
+					/* disable ACK for final READ */
+					if (i == data_len - 1)
+						i2c->IICCON &= ~0x80;
+					ReadWriteByte ();
+					result = WaitForXfer ();
+					data[i] = i2c->IICDS;
+					i++;
+				}
+			} else {
+				result = I2C_NACK;
+			}
+
+		} else {
+			i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA;
+			i2c->IICDS = chip;
+			/* send START */
+			i2c->IICSTAT |= I2C_START_STOP;
+			result = WaitForXfer ();
+
+			if (IsACK ()) {
+				i = 0;
+				while ((i < data_len) && (result == I2C_OK)) {
+					/* disable ACK for final READ */
+					if (i == data_len - 1)
+						i2c->IICCON &= ~0x80;
+					ReadWriteByte ();
+					result = WaitForXfer ();
+					data[i] = i2c->IICDS;
+					i++;
+				}
+			} else {
+				result = I2C_NACK;
+			}
+		}
+
+		/* send STOP */
+		i2c->IICSTAT = I2C_MODE_MR | I2C_TXRX_ENA;
+		ReadWriteByte ();
+		break;
+
+	default:
+		printf ("i2c_transfer: bad call\n");
+		result = I2C_NOK;
+		break;
+	}
+
+	return (result);
+}
+
+int i2c_probe (uchar chip)
+{
+	uchar buf[1];
+
+	buf[0] = 0;
+
+	/*
+	 * What is needed is to send the chip address and verify that the
+	 * address was <ACK>ed (i.e. there was a chip at that address which
+	 * drove the data line low).
+	 */
+	return (i2c_transfer (I2C_READ, chip << 1, 0, 0, buf, 1) != I2C_OK);
+}
+
+int i2c_read (uchar chip, uint addr, int alen, uchar * buffer, int len)
+{
+	uchar xaddr[4];
+	int ret;
+
+	if (alen > 4) {
+		printf ("I2C read: addr len %d not supported\n", alen);
+		return 1;
+	}
+
+	if (alen > 0) {
+		xaddr[0] = (addr >> 24) & 0xFF;
+		xaddr[1] = (addr >> 16) & 0xFF;
+		xaddr[2] = (addr >> 8) & 0xFF;
+		xaddr[3] = addr & 0xFF;
+	}
+
+#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
+	/*
+	 * EEPROM chips that implement "address overflow" are ones
+	 * like Catalyst 24WC04/08/16 which has 9/10/11 bits of
+	 * address and the extra bits end up in the "chip address"
+	 * bit slots. This makes a 24WC08 (1Kbyte) chip look like
+	 * four 256 byte chips.
+	 *
+	 * Note that we consider the length of the address field to
+	 * still be one byte because the extra address bits are
+	 * hidden in the chip address.
+	 */
+	if (alen > 0)
+		chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
+#endif
+	if ((ret =
+	     i2c_transfer (I2C_READ, chip << 1, &xaddr[4 - alen], alen,
+			   buffer, len)) != 0) {
+		printf ("I2c read: failed %d\n", ret);
+		return 1;
+	}
+	return 0;
+}
+
+int i2c_write (uchar chip, uint addr, int alen, uchar * buffer, int len)
+{
+	uchar xaddr[4];
+
+	if (alen > 4) {
+		printf ("I2C write: addr len %d not supported\n", alen);
+		return 1;
+	}
+
+	if (alen > 0) {
+		xaddr[0] = (addr >> 24) & 0xFF;
+		xaddr[1] = (addr >> 16) & 0xFF;
+		xaddr[2] = (addr >> 8) & 0xFF;
+		xaddr[3] = addr & 0xFF;
+	}
+#ifdef CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW
+	/*
+	 * EEPROM chips that implement "address overflow" are ones
+	 * like Catalyst 24WC04/08/16 which has 9/10/11 bits of
+	 * address and the extra bits end up in the "chip address"
+	 * bit slots. This makes a 24WC08 (1Kbyte) chip look like
+	 * four 256 byte chips.
+	 *
+	 * Note that we consider the length of the address field to
+	 * still be one byte because the extra address bits are
+	 * hidden in the chip address.
+	 */
+	if (alen > 0)
+		chip |= ((addr >> (alen * 8)) & CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW);
+#endif
+	return (i2c_transfer
+		(I2C_WRITE, chip << 1, &xaddr[4 - alen], alen, buffer,
+		 len) != 0);
+}
+#endif	/* CONFIG_HARD_I2C */