Merge commit 'origin/master'

7 files changed, 805 insertions, 4 deletions

diff --git a/doc/README.bamboo b/doc/README.bamboo
index b50be01..e139c6d 100644
--- a/doc/README.bamboo
+++ b/doc/README.bamboo
@@ -1,3 +1,65 @@
+The 2 important dipswitches are configured as shown below:
+
+SW1 (for 33MHz SysClk)
+----------------------
+S1   S2   S3   S4   S5   S6   S7   S8
+OFF  OFF  OFF  OFF  OFF  OFF  OFF  ON
+
+SW7 (for Op-Code Flash and Boot Option H)
+-----------------------------------------
+S1   S2   S3   S4   S5   S6   S7   S8
+OFF  OFF  OFF  ON   OFF  OFF  OFF  OFF
+
+The EEPROM at location 0x52 is loaded with these 16 bytes:
+C47042A6 05D7A190 40082350 0d050000
+
+SDR0_SDSTP0[ENG]:	1		: PLL's VCO is the source for PLL forward divisors
+SDR0_SDSTP0[SRC]:	1		: Feedback originates from PLLOUTB
+SDR0_SDSTP0[SEL]:	0		: Feedback selection is PLL output
+SDR0_SDSTP0[TUNE]:	1000111000	: 10 <= M <= 22, 600MHz < VCO <= 900MHz
+SDR0_SDSTP0[FBDV]:	4		: PLL feedback divisor
+SDR0_SDSTP0[FBDVA]:	2		: PLL forward divisor A
+SDR0_SDSTP0[FBDVB]:	5		: PLL forward divisor B
+SDR0_SDSTP0[PRBDV0]:	1		: PLL primary divisor B
+SDR0_SDSTP0[OPBDV0]:	2		: OPB clock divisor
+SDR0_SDSTP0[LFBDV]:	1		: PLL local feedback divisor
+SDR0_SDSTP0[PERDV0]:	3		: Peripheral clock divisor 0
+SDR0_SDSTP0[MALDV0]:	2		: MAL clock divisor 0
+SDR0_SDSTP0[PCIDV0]:	2		: Sync PCI clock divisor 0
+SDR0_SDSTP0[PLLTIMER]:	7		: PLL locking timer
+SDR0_SDSTP0[RW]:	1		: EBC ROM width: 16-bit
+SDR0_SDSTP0[RL]:	0		: EBC ROM location: EBC
+SDR0_SDSTP0[PAE]:	0		: PCI internal arbiter: disabled
+SDR0_SDSTP0[PHCE]:	0		: PCI host configuration: disabled
+SDR0_SDSTP0[ZM]:	3		: ZMII mode: RMII mode 100
+SDR0_SDSTP0[CTE]:	0		: CPU trace: disabled
+SDR0_SDSTP0[Nto1]:	0		: CPU/PLB ratio N/P: not N to 1
+SDR0_SDSTP0[PAME]:	1		: PCI asynchronous mode: enabled
+SDR0_SDSTP0[MEM]:	1		: Multiplex: EMAC
+SDR0_SDSTP0[NE]:	0		: NDFC: disabled
+SDR0_SDSTP0[NBW]:	0		: NDFC boot width: 8-bit
+SDR0_SDSTP0[NBW]:	0		: NDFC boot page selection
+SDR0_SDSTP0[NBAC]:	0		: NDFC boot address selection cycle: 3 Addr. Cycles, 1 Col. + 2 Row (512 page size)
+SDR0_SDSTP0[NARE]:	0		: NDFC auto read : disabled
+SDR0_SDSTP0[NRB]:	0		: NDFC Ready/Busy : Ready
+SDR0_SDSTP0[NDRSC]:	33333		: NDFC device reset counter
+SDR0_SDSTP0[NCG0]:	0		: NDFC/EBC chip select gating CS0 : EBC
+SDR0_SDSTP0[NCG1]:	0		: NDFC/EBC chip select gating CS1 : EBC
+SDR0_SDSTP0[NCG2]:	0		: NDFC/EBC chip select gating CS2 : EBC
+SDR0_SDSTP0[NCG3]:	0		: NDFC/EBC chip select gating CS3 : EBC
+SDR0_SDSTP0[NCRDC]:	3333		: NDFC device read count
+
+PPC440EP Clocking Configuration
+
+SysClk is 33.0MHz, M is 20, VCO is 660.0MHz, CPU is 330.0MHz, PLB is 132.0MHz
+OPB is 66.0MHz, EBC is 44.0MHz, MAL is 66.0MHz, Sync PCI is 66.0MHz
+
+The above information is reported by Eugene O'Brien
+<Eugene.O'Brien@advantechamt.com>. Thanks a lot.
+
+2007-08-06, Stefan Roese <sr@denx.de>
+---------------------------------------------------------------------
+
 The configuration for the AMCC 440EP eval board "Bamboo" was changed
 to only use 384 kbytes of FLASH for the U-Boot image. This way the
 redundant environment can be saved in the remaining 2 sectors of the
diff --git a/doc/README.generic_usb_ohci b/doc/README.generic_usb_ohci
index c343dfd..494dd1f 100644
--- a/doc/README.generic_usb_ohci
+++ b/doc/README.generic_usb_ohci
@@ -41,7 +41,7 @@ mpc5xxx. For these the config option
 
 	CFG_OHCI_BE_CONTROLLER
 
-needs to be defined. 
+needs to be defined.
 
 
 PCI Controllers
@@ -55,6 +55,3 @@ PCI Controllers need to do byte swapping on register accesses, so they
 should to define:
 
 	CFG_OHCI_SWAP_REG_ACCESS
-
-
-
diff --git a/doc/README.m5253evbe b/doc/README.m5253evbe
new file mode 100644
index 0000000..0426cb1
--- /dev/null
+++ b/doc/README.m5253evbe
@@ -0,0 +1,103 @@
+Freescale Amadeus Plus M5253EVBE board
+======================================
+
+Hayden Fraser(Hayden.Fraser@freescale.com)
+Created 06/05/2007
+===========================================
+
+
+1. SWITCH SETTINGS
+==================
+1.1 N/A
+
+
+2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
+===========================================
+2.1. For the initial bringup, we adopted a consistent memory scheme between u-boot and
+	linux kernel, you can customize it based on your system requirements:
+	SDR:	0x00000000-0x00ffffff
+	SRAM0:	0x20010000-0x20017fff
+	SRAM1:	0x20000000-0x2000ffff
+	MBAR1:	0x10000000-0x4fffffff
+	MBAR2:	0x80000000-0xCfffffff
+	Flash:	0xffe00000-0xffffffff
+
+3. DEFINITIONS AND COMPILATION
+==============================
+3.1 Explanation on NEW definitions in include/configs/M5253EVBE.h
+	CONFIG_MCF52x2		Processor family
+	CONFIG_MCF5253		MCF5253 specific
+	CONFIG_M5253EVBE	Amadeus Plus board specific
+	CFG_CLK			Define Amadeus Plus CPU Clock
+	CFG_MBAR		MBAR base address
+	CFG_MBAR2		MBAR2 base address
+
+3.2 Compilation
+	export CROSS_COMPILE=/usr/local/freescale-coldfire-4.1-elf/bin/m68k-elf-
+	cd u-boot-1-2-x
+	make distclean
+	make M5253EVBE_config
+	make
+
+
+4. SCREEN DUMP
+==============
+4.1 U-Boot 1.2.0 (Jun 18 2007 - 18:20:00)
+
+CPU:   Freescale Coldfire MCF5253 at 62 MHz
+Board: Freescale MCF5253 EVBE
+DRAM:  16 MB
+FLASH:  2 MB
+In:    serial
+Out:   serial
+Err:   serial
+=> flinfo
+
+Bank # 1: CFI conformant FLASH (16 x 16)  Size: 2 MB in 35 Sectors
+  AMD Standard command set, Manufacturer ID: 0x01, Device ID: 0x49
+  Erase timeout: 16384 ms, write timeout: 1 ms
+
+  Sector Start Addresses:
+  FFE00000   RO   FFE04000   RO   FFE06000   RO   FFE08000   RO   FFE10000   RO
+  FFE20000        FFE30000        FFE40000        FFE50000        FFE60000
+  FFE70000        FFE80000        FFE90000        FFEA0000        FFEB0000
+  FFEC0000        FFED0000        FFEE0000        FFEF0000        FFF00000
+  FFF10000        FFF20000        FFF30000        FFF40000        FFF50000
+  FFF60000        FFF70000        FFF80000        FFF90000        FFFA0000
+  FFFB0000        FFFC0000        FFFD0000        FFFE0000        FFFF0000
+
+=> bdinfo
+boot_params = 0x00F62F90
+memstart    = 0x00000000
+memsize     = 0x01000000
+flashstart  = 0xFFE00000
+flashsize   = 0x00200000
+flashoffset = 0x00000000
+baudrate    = 19200 bps
+
+=> printenv
+bootdelay=5
+baudrate=19200
+stdin=serial
+stdout=serial
+stderr=serial
+
+Environment size: 134/8188 bytes
+=> saveenv
+Saving Environment to Flash...
+Un-Protected 1 sectors
+Erasing Flash...
+. done
+Erased 1 sectors
+Writing to Flash... done
+Protected 1 sectors
+=>
+
+5. COMPILER
+-----------
+To create U-Boot the CodeSourcery's version of the GNU Toolchain for the ColdFire architecture
+compiler set (freescale-coldfire-4.1-elf) from www.codesourcery.com was used.
+You can download it from:http://www.codesourcery.com/gnu_toolchains/coldfire/download.html
+
+compiler that you used - for example, codesourcery_elf requires -MQ in rules.mk, old M68K 2.95.3 just -M
+codesourcery_elf requires -MQ in rules.mk, old M68K 2.95.3 just -M
diff --git a/doc/README.m54455evb b/doc/README.m54455evb
new file mode 100644
index 0000000..119a19d
--- /dev/null
+++ b/doc/README.m54455evb
@@ -0,0 +1,416 @@
+Freescale MCF54455EVB ColdFire Development Board
+================================================
+
+TsiChung Liew(Tsi-Chung.Liew@freescale.com)
+Created 4/08/07
+===========================================
+
+
+Changed files:
+==============
+
+- board/freescale/m54455evb/m54455evb.c	Dram setup, IDE pre init, and PCI init
+- board/freescale/m54455evb/flash.c		Atmel and INTEL flash support
+- board/freescale/m54455evb/Makefile		Makefile
+- board/freescale/m54455evb/config.mk	config make
+- board/freescale/m54455evb/u-boot.lds	Linker description
+
+- common/cmd_bdinfo.c		Clock frequencies output
+- common/cmd_mii.c		mii support
+
+- cpu/mcf5445x/cpu.c		cpu specific code
+- cpu/mcf5445x/cpu_init.c	Flexbus ChipSelect, Mux pins setup, icache and RTC extra regs
+- cpu/mcf5445x/interrupts.c	cpu specific interrupt support
+- cpu/mcf5445x/speed.c		system, pci, flexbus, and cpu clock
+- cpu/mcf5445x/Makefile		Makefile
+- cpu/mcf5445x/config.mk	config make
+- cpu/mcf5445x/start.S		start up assembly code
+
+- doc/README.m54455evb	This readme file
+
+- drivers/net/mcffec.c		ColdFire common FEC driver
+- drivers/serial/mcfuart.c	ColdFire common UART driver
+
+- include/asm-m68k/bitops.h		Bit operation function export
+- include/asm-m68k/byteorder.h		Byte order functions
+- include/asm-m68k/fec.h		FEC structure and definition
+- include/asm-m68k/fsl_i2c.h		I2C structure and definition
+- include/asm-m68k/global_data.h	Global data structure
+- include/asm-m68k/immap.h		ColdFire specific header file and driver macros
+- include/asm-m68k/immap_5445x.h	mcf5445x specific header file
+- include/asm-m68k/io.h			io functions
+- include/asm-m68k/m5445x.h		mcf5445x specific header file
+- include/asm-m68k/posix_types.h	Posix
+- include/asm-m68k/processor.h		header file
+- include/asm-m68k/ptrace.h		Exception structure
+- include/asm-m68k/rtc.h		Realtime clock header file
+- include/asm-m68k/string.h		String function export
+- include/asm-m68k/timer.h		Timer structure and definition
+- include/asm-m68k/types.h		Data types definition
+- include/asm-m68k/uart.h		Uart structure and definition
+- include/asm-m68k/u-boot.h		u-boot structure
+
+- include/configs/M54455EVB.h	Board specific configuration file
+
+- lib_m68k/board.c			board init function
+- lib_m68k/cache.c
+- lib_m68k/interrupts			Coldfire common interrupt functions
+- lib_m68k/m68k_linux.c
+- lib_m68k/time.c			Timer functions (Dma timer and PIT)
+- lib_m68k/traps.c			Exception init code
+
+- rtc/mcfrtc.c				Realtime clock Driver
+
+1 MCF5445x specific Options/Settings
+====================================
+1.1 pre-loader is no longer suppoer in thie coldfire family
+
+1.2 Configuration settings for M54455EVB Development Board
+CONFIG_MCF5445x		-- define for all MCF5445x CPUs
+CONFIG_M54455		-- define for all Freescale MCF54455 CPUs
+CONFIG_M54455EVB	-- define for M54455EVB board
+
+CONFIG_MCFUART		-- define to use common CF Uart driver
+CFG_UART_PORT		-- define UART port number, start with 0, 1 and 2
+CONFIG_BAUDRATE		-- define UART baudrate
+
+CONFIG_MCFRTC		-- define to use common CF RTC driver
+CFG_MCFRTC_BASE		-- provide base address for RTC in immap.h
+CFG_RTC_OSCILLATOR	-- define RTC clock frequency
+RTC_DEBUG		-- define to show RTC debug message
+CONFIG_CMD_DATE		-- enable to use date feature in u-boot
+
+CONFIG_MCFFEC		-- define to use common CF FEC driver
+CONFIG_NET_MULTI	-- define to use multi FEC in u-boot
+CONFIG_MII		-- enable to use MII driver
+CONFIG_CF_DOMII 	-- enable to use MII feature in cmd_mii.c
+CFG_DISCOVER_PHY	-- enable PHY discovery
+CFG_RX_ETH_BUFFER	-- Set FEC Receive buffer
+CFG_FAULT_ECHO_LINK_DOWN--
+CFG_FEC0_PINMUX		-- Set FEC0 Pin configuration
+CFG_FEC1_PINMUX		-- Set FEC1 Pin configuration
+CFG_FEC0_MIIBASE	-- Set FEC0 MII base register
+CFG_FEC1_MIIBASE	-- Set FEC0 MII base register
+MCFFEC_TOUT_LOOP	-- set FEC timeout loop
+CONFIG_HAS_ETH1		-- define to enable second FEC in u-boot
+
+CONFIG_ISO_PARTITION	-- enable ISO read/write
+CONFIG_DOS_PARTITION	-- enable DOS read/write
+CONFIG_IDE_RESET	-- define ide_reset()
+CONFIG_IDE_PREINIT	-- define ide_preinit()
+CONFIG_ATAPI		-- define ATAPI support
+CONFIG_LBA48		-- define LBA48 (larger than 120GB) support
+CFG_IDE_MAXBUS		-- define max channel
+CFG_IDE_MAXDEVICE	-- define max devices per channel
+CFG_ATA_BASE_ADDR	-- define ATA base address
+CFG_ATA_IDE0_OFFSET	-- define ATA IDE0 offset
+CFG_ATA_DATA_OFFSET	-- define ATA data IO
+CFG_ATA_REG_OFFSET	-- define for normal register accesses
+CFG_ATA_ALT_OFFSET	-- define for alternate registers
+CFG_ATA_STRIDE      	-- define for Interval between registers
+_IO_BASE		-- define for IO base address
+
+CONFIG_MCFTMR		-- define to use DMA timer
+CONFIG_MCFPIT		-- define to use PIT timer
+
+CONFIG_FSL_I2C		-- define to use FSL common I2C driver
+CONFIG_HARD_I2C		-- define for I2C hardware support
+CONFIG_SOFT_I2C		-- define for I2C bit-banged
+CFG_I2C_SPEED		-- define for I2C speed
+CFG_I2C_SLAVE		-- define for I2C slave address
+CFG_I2C_OFFSET		-- define for I2C base address offset
+CFG_IMMR		-- define for MBAR offset
+
+CONFIG_PCI              -- define for PCI support
+CONFIG_PCI_PNP          -- define for Plug n play support
+CFG_PCI_MEM_BUS		-- PCI memory logical offset
+CFG_PCI_MEM_PHYS	-- PCI memory physical offset
+CFG_PCI_MEM_SIZE	-- PCI memory size
+CFG_PCI_IO_BUS		-- PCI IO logical offset
+CFG_PCI_IO_PHYS		-- PCI IO physical offset
+CFG_PCI_IO_SIZE		-- PCI IO size
+CFG_PCI_CFG_BUS		-- PCI Configuration logical offset
+CFG_PCI_CFG_PHYS	-- PCI Configuration physical offset
+CFG_PCI_CFG_SIZE	-- PCI Configuration size
+
+CONFIG_EXTRA_CLOCK	-- Enable extra clock such as vco, flexbus, pci, etc
+
+CFG_MBAR		-- define MBAR offset
+
+CFG_ATMEL_BOOT		-- To determine the u-boot is booted from Atmel or Intel
+
+CONFIG_MONITOR_IS_IN_RAM -- Not support
+
+CFG_INIT_RAM_ADDR	-- defines the base address of the MCF54455 internal SRAM
+
+CFG_CSn_BASE	-- defines the Chip Select Base register
+CFG_CSn_MASK	-- defines the Chip Select Mask register
+CFG_CSn_CTRL	-- defines the Chip Select Control register
+
+CFG_ATMEL_BASE	-- defines the Atmel Flash base
+CFG_INTEL_BASE	-- defines the Intel Flash base
+
+CFG_SDRAM_BASE	-- defines the DRAM Base
+CFG_SDRAM_BASE1	-- defines the DRAM Base 1
+
+2. MEMORY MAP UNDER U-BOOT AND LINUX KERNEL
+===========================================
+2.1. System memory map:
+	Flash:		0x00000000-0x3FFFFFFF (1024MB)
+	DDR:		0x40000000-0x7FFFFFFF (1024MB)
+	SRAM:		0x80000000-0x8FFFFFFF (256MB)
+	ATA:		0x90000000-0x9FFFFFFF (256MB)
+	PCI:		0xA0000000-0xBFFFFFFF (512MB)
+	FlexBus:	0xC0000000-0xDFFFFFFF (512MB)
+	IP:		0xF0000000-0xFFFFFFFF (256MB)
+
+2.2. For the initial bringup, we adopted a consistent memory scheme between u-boot and
+	linux kernel, you can customize it based on your system requirements:
+	Atmel boot:
+	Flash0:		0x00000000-0x0007FFFF (512KB)
+	Flash1:		0x04000000-0x05FFFFFF (32MB)
+	Intel boot:
+	Flash0:		0x00000000-0x01FFFFFF (32MB)
+	Flash1:		0x04000000-0x0407FFFF (512KB)
+
+	CPLD:		0x08000000-0x08FFFFFF (16MB)
+	FPGA:		0x09000000-0x09FFFFFF (16MB)
+	DDR:		0x40000000-0x4FFFFFFF (256MB)
+	SRAM:		0x80000000-0x80007FFF (32KB)
+	IP:		0xFC000000-0xFC0FFFFF (64KB)
+
+3. SWITCH SETTINGS
+==================
+3.1 SW1 Pin3: 0 - Boot from Atmel or 1 - INTEL
+	SW1 Pin4: 0 - ULPI chip not in reset state or 1 - ULPI chip in reset state
+	SW1 Pin5: 0 - Full ATA Bus enabled, FEC Phy1 powered down
+			  1 - Upper 8 bits ATA data bus disabled, FEC PHY1 active
+	SW1 Pin6: 0 - FEC Phy0 active or 1 - FEC Phy0 powered down
+	SW1 Pin3: 0 - Boot from Atmel or 1 - INTEL
+
+4. COMPILATION
+==============
+4.1	To create U-Boot the gcc-4.1-32 compiler set (ColdFire ELF version)
+from codesourcery.com was used. Download it from:
+http://www.codesourcery.com/gnu_toolchains/coldfire/download.html
+
+4.2 Compilation
+   export CROSS_COMPILE=cross-compile-prefix
+   cd u-boot-1.x.x
+   make distclean
+   make M54455EVB_config, or		- default to atmel 33Mhz input clock
+   make M54455EVB_atmel_config, or	- default to atmel 33Mhz input clock
+   make M54455EVB_a33_config, or	- default to atmel 33Mhz input clock
+   make M54455EVB_a66_config, or	- default to atmel 66Mhz input clock
+   make M54455EVB_intel_config, or	- default to intel 33Mhz input clock
+   make M54455EVB_i33_config, or	- default to intel 33Mhz input clock
+   make M54455EVB_i66_config, or	- default to intel 66Mhz input clock
+   make
+
+5. SCREEN DUMP
+==============
+5.1 M54455EVB Development board
+    Boot from Atmel (NOTE: May not show exactly the same)
+
+U-Boot 1.2.0-g98c80b46-dirty (Jul 26 2007 - 12:44:08)
+
+CPU:   Freescale MCF54455 (Mask:48 Version:1)
+       CPU CLK 266 Mhz BUS CLK 133 Mhz FLB CLK 66 Mhz
+       PCI CLK 33 Mhz INP CLK 33 Mhz VCO CLK 533 Mhz
+Board: Freescale M54455 EVB
+I2C:   ready
+DRAM:  256 MB
+FLASH: 16.5 MB
+In:    serial
+Out:   serial
+Err:   serial
+Net:   FEC0, FEC1
+IDE:   Bus 0: not available
+-> print
+bootargs=root=/dev/ram rw
+bootdelay=1
+baudrate=115200
+ethaddr=00:e0:0c:bc:e5:60
+eth1addr=00:e0:0c:bc:e5:61
+hostname=M54455EVB
+netdev=eth0
+inpclk=33333333
+loadaddr=40010000
+load=tftp ${loadaddr) ${u-boot}
+upd=run load; run prog
+prog=prot off 0 2ffff;era 0 2ffff;cp.b ${loadaddr} 0 ${filesize};save
+ethact=FEC0
+mtdids=nor0=M54455EVB-1
+mtdparts=M54455EVB-1:16m(user)
+u-boot=u-boot54455.bin
+filesize=292b4
+fileaddr=40010000
+gatewayip=192.168.1.1
+netmask=255.255.255.0
+ipaddr=192.168.1.3
+serverip=192.168.1.2
+stdin=serial
+stdout=serial
+stderr=serial
+mem=261632k
+
+Environment size: 563/8188 bytes
+-> bdinfo
+memstart    = 0x40000000
+memsize     = 0x10000000
+flashstart  = 0x00000000
+flashsize   = 0x01080000
+flashoffset = 0x00000000
+sramstart   = 0x80000000
+sramsize    = 0x00008000
+mbar        = 0xFC000000
+busfreq     = 133.333 MHz
+pcifreq     = 33.333 MHz
+flbfreq     = 66.666 MHz
+inpfreq     = 33.333 MHz
+vcofreq     = 533.333 MHz
+ethaddr     = 00:E0:0C:BC:E5:60
+eth1addr    = 00:E0:0C:BC:E5:61
+ip_addr     = 192.168.1.3
+baudrate    = 115200 bps
+->
+-> help
+?       - alias for 'help'
+autoscr - run script from memory
+base    - print or set address offset
+bdinfo  - print Board Info structure
+boot    - boot default, i.e., run 'bootcmd'
+bootd   - boot default, i.e., run 'bootcmd'
+bootelf - Boot from an ELF image in memory
+bootm   - boot application image from memory
+bootp	- boot image via network using BootP/TFTP protocol
+bootvx  - Boot vxWorks from an ELF image
+cmp     - memory compare
+coninfo - print console devices and information
+cp      - memory copy
+crc32   - checksum calculation
+date    - get/set/reset date & time
+dcache  - enable or disable data cache
+diskboot- boot from IDE device
+echo    - echo args to console
+erase   - erase FLASH memory
+ext2load- load binary file from a Ext2 filesystem
+ext2ls  - list files in a directory (default /)
+fatinfo - print information about filesystem
+fatload - load binary file from a dos filesystem
+fatls   - list files in a directory (default /)
+flinfo  - print FLASH memory information
+fsinfo	- print information about filesystems
+fsload	- load binary file from a filesystem image
+go      - start application at address 'addr'
+help    - print online help
+icache  - enable or disable instruction cache
+icrc32  - checksum calculation
+ide     - IDE sub-system
+iloop   - infinite loop on address range
+imd     - i2c memory display
+iminfo  - print header information for application image
+imls    - list all images found in flash
+imm     - i2c memory modify (auto-incrementing)
+imw     - memory write (fill)
+inm     - memory modify (constant address)
+iprobe  - probe to discover valid I2C chip addresses
+itest	- return true/false on integer compare
+loadb   - load binary file over serial line (kermit mode)
+loads   - load S-Record file over serial line
+loady   - load binary file over serial line (ymodem mode)
+loop    - infinite loop on address range
+ls	- list files in a directory (default /)
+md      - memory display
+mii     - MII utility commands
+mm      - memory modify (auto-incrementing)
+mtest   - simple RAM test
+mw      - memory write (fill)
+nfs	- boot image via network using NFS protocol
+nm      - memory modify (constant address)
+pci     - list and access PCI Configuration Space
+ping	- send ICMP ECHO_REQUEST to network host
+printenv- print environment variables
+protect - enable or disable FLASH write protection
+rarpboot- boot image via network using RARP/TFTP protocol
+reset   - Perform RESET of the CPU
+run     - run commands in an environment variable
+saveenv - save environment variables to persistent storage
+setenv  - set environment variables
+sleep   - delay execution for some time
+tftpboot- boot image via network using TFTP protocol
+version - print monitor version
+->bootm 4000000
+
+## Booting image at 04000000 ...
+   Image Name:   Linux Kernel Image
+   Created:      2007-08-14  15:13:00 UTC
+   Image Type:   M68K Linux Kernel Image (uncompressed)
+   Data Size:    2301952 Bytes =  2.2 MB
+   Load Address: 40020000
+   Entry Point:  40020000
+   Verifying Checksum ... OK
+OK
+Linux version 2.6.20-gfe5136d6-dirty (mattw@kea) (gcc version 4.2.0 20070318 (pr
+erelease) (Sourcery G++ Lite 4.2-20)) #108 Mon Aug 13 13:00:13 MDT 2007
+starting up linux startmem 0xc0254000, endmem 0xcfffffff, size 253MB
+Built 1 zonelists.  Total pages: 32624
+Kernel command line: root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=ph
+ysmap-flash.0:5M(kernel)ro,-(jffs2)
+PID hash table entries: 1024 (order: 10, 4096 bytes)
+Console: colour dummy device 80x25
+Dentry cache hash table entries: 32768 (order: 4, 131072 bytes)
+Inode-cache hash table entries: 16384 (order: 3, 65536 bytes)
+Memory: 257496k/262136k available (1864k kernel code, 2440k data, 88k init)
+Mount-cache hash table entries: 1024
+NET: Registered protocol family 16
+SCSI subsystem initialized
+NET: Registered protocol family 2
+IP route cache hash table entries: 2048 (order: 0, 8192 bytes)
+TCP established hash table entries: 8192 (order: 2, 32768 bytes)
+TCP bind hash table entries: 4096 (order: 1, 16384 bytes)
+TCP: Hash tables configured (established 8192 bind 4096)
+TCP reno registered
+JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
+io scheduler noop registered
+io scheduler anticipatory registered
+io scheduler deadline registered
+io scheduler cfq registered (default)
+ColdFire internal UART serial driver version 1.00
+ttyS0 at 0xfc060000 (irq = 90) is a builtin ColdFire UART
+ttyS1 at 0xfc064000 (irq = 91) is a builtin ColdFire UART
+ttyS2 at 0xfc068000 (irq = 92) is a builtin ColdFire UART
+RAMDISK driver initialized: 16 RAM disks of 64000K size 1024 blocksize
+loop: loaded (max 8 devices)
+FEC ENET Version 0.2
+fec: PHY @ 0x0, ID 0x20005ca2 -- DP83849
+eth0: ethernet 00:08:ee:00:e4:19
+physmap platform flash device: 01000000 at 04000000
+physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
+ Intel/Sharp Extended Query Table at 0x0031
+Using buffer write method
+cfi_cmdset_0001: Erase suspend on write enabled
+2 cmdlinepart partitions found on MTD device physmap-flash.0
+Creating 2 MTD partitions on "physmap-flash.0":
+0x00000000-0x00500000 : "kernel"
+mtd: Giving out device 0 to kernel
+0x00500000-0x01000000 : "jffs2"
+mtd: Giving out device 1 to jffs2
+mice: PS/2 mouse device common for all mice
+i2c /dev entries driver
+TCP cubic registered
+NET: Registered protocol family 1
+NET: Registered protocol family 17
+NET: Registered protocol family 15
+VFS: Mounted root (jffs2 filesystem).
+Setting the hostname to freescale
+Mounting filesystems
+mount: Mounting usbfs on /proc/bus/usb failed: No such file or directory
+Starting syslogd and klogd
+Setting up networking on loopback device:
+Setting up networking on eth0:
+eth0: config: auto-negotiation on, 100FDX, 100HDX, 10FDX, 10HDX.
+Adding static route for default gateway to 172.27.255.254:
+Setting nameserver to 172.27.0.1 in /etc/resolv.conf:
+Starting inetd:
+/ #
diff --git a/doc/README.mpc8544ds b/doc/README.mpc8544ds
new file mode 100644
index 0000000..bf257a0
--- /dev/null
+++ b/doc/README.mpc8544ds
@@ -0,0 +1,122 @@
+Overview
+--------
+The MPC8544DS system is similar to the 85xx CDS systems such
+as the MPC8548CDS due to the similar E500 core.  However, it
+is placed on the same board as the 8641 HPCN system.
+
+
+Flash Banks
+-----------
+Like the 85xx CDS systems, the 8544 DS board has two flash banks.
+They are both present on boot, but there locations can be swapped
+using the dip-switch SW10, bit 2.
+
+However, unlike the CDS systems, but similar to the 8641 HPCN
+board, a runtime reset through the FPGA can also affect a swap
+on the flash bank mappings for the next reset cycle.
+
+Irrespective of the switch SW10[2], booting is always from the
+boot bank at 0xfff8_0000.
+
+
+Memory Map
+----------
+
+0xff80_0000 - 0xffbf_ffff	Alernate bank		4MB
+0xffc0_0000 - 0xffff_ffff	Boot bank		4MB
+
+0xffb8_0000			Alternate image start	512KB
+0xfff8_0000			Boot image start	512KB
+
+
+Flashing Images
+---------------
+
+For example, to place a new image in the alternate flash bank
+and then reset with that new image temporarily, use this:
+
+    tftp 1000000 u-boot.bin.8544ds
+    erase ffb80000 ffbfffff
+    cp.b 1000000 ffb80000 80000
+    pixis_reset altbank
+
+
+To overwrite the image in the boot flash bank:
+
+    tftp 1000000 u-boot.bin.8544ds
+    protect off all
+    erase fff80000 ffffffff
+    cp.b 1000000 fff80000 80000
+
+Other example U-Boot image and flash manipulations examples
+can be found in the README.mpc85xxcds file as well.
+
+
+The pixis_reset command
+-----------------------
+A new command, "pixis_reset", is introduced to reset mpc8641hpcn board
+using the FPGA sequencer.  When the board restarts, it has the option
+of using either the current or alternate flash bank as the boot
+image, with or without the watchdog timer enabled, and finally with
+or without frequency changes.
+
+Usage is;
+
+	pixis_reset
+	pixis_reset altbank
+	pixis_reset altbank wd
+	pixis_reset altbank cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
+	pixis_reset cf <SYSCLK freq> <COREPLL ratio> <MPXPLL ratio>
+
+Examples;
+
+	/* reset to current bank, like "reset" command */
+	pixis_reset
+
+	/* reset board but use the to alternate flash bank */
+	pixis_reset altbank
+
+	/* reset board, use alternate flash bank with watchdog timer enabled*/
+	pixis_reset altbank wd
+
+	/* reset board to alternate bank with frequency changed.
+	 * 40 is SYSCLK, 2.5 is COREPLL ratio, 10 is MPXPLL ratio
+	 */
+	pixis-reset altbank cf 40 2.5 10
+
+Valid clock choices are in the 8641 Reference Manuals.
+
+
+Using the Device Tree Source File
+---------------------------------
+To create the DTB (Device Tree Binary) image file,
+use a command similar to this:
+
+    dtc -b 0 -f -I dts -O dtb mpc8544ds.dts > mpc8544ds.dtb
+
+Likely, that .dts file will come from here;
+
+    linux-2.6/arch/powerpc/boot/dts/mpc8544ds.dts
+
+After placing the DTB file in your TFTP disk area,
+you can download that dtb file using a command like:
+
+    tftp 900000 mpc8544ds.dtb
+
+Burn it to flash if you want.
+
+
+Booting Linux
+-------------
+
+Place a linux uImage in the TFTP disk area too.
+
+    tftp 1000000 uImage.8544
+    tftp 900000 mpc8544ds.dtb
+    bootm 1000000 - 900000
+
+Watch your ethact, netdev and bootargs U-Boot environment variables.
+You may want to do something like this too:
+
+    setenv ethact eTSEC3
+    setenv netdev eth1
diff --git a/doc/README.sbc8641d b/doc/README.sbc8641d
new file mode 100644
index 0000000..a051466
--- /dev/null
+++ b/doc/README.sbc8641d
@@ -0,0 +1,28 @@
+Wind River SBC8641D reference board
+===========================
+
+Created 06/14/2007 Joe Hamman
+Copyright 2007, Embedded Specialties, Inc.
+Copyright 2007 Wind River Systemes, Inc.
+-----------------------------
+
+1. Building U-Boot
+------------------
+The SBC8641D code is known to build using ELDK 4.1.
+
+    $ make sbc8641d_config
+    Configuring for sbc8641d board...
+
+    $ make
+
+
+2. Switch and Jumper Settings
+-----------------------------
+All Jumpers & Switches are in their default positions.  Please refer to
+the board documentation for details.  Some settings control CPU voltages
+and settings may change with board revisions.
+
+3. Known limitations
+--------------------
+PCI:
+	The PCI command may hang if no boards are present in either slot.
diff --git a/doc/README.zeus b/doc/README.zeus
new file mode 100644
index 0000000..1848d8c
--- /dev/null
+++ b/doc/README.zeus
@@ -0,0 +1,73 @@
+
+Storage of the board specific values (ethaddr...)
+-------------------------------------------------
+
+The board specific environment variables that should be unique
+for each individual board, can be stored in the I2C EEPROM. This
+will be done from offset 0x80 with the length of 0x80 bytes. The
+following command can be used to store the values here:
+
+=> setdef de:20:6a:ed:e2:72 de:20:6a:ed:e2:73 AB0001
+
+	  ethaddr           eth1addr          serial#
+
+Now those 3 values are stored into the I2C EEPROM. A CRC is added
+to make sure that the values get not corrupted.
+
+
+SW-Reset Pushbutton handling:
+-----------------------------
+
+The SW-reset push button is connected to a GPIO input too. This
+way U-Boot can "see" how long the SW-reset was pressed, and a
+specific action can be taken. Two different actions are supported:
+
+a) Release after more than 5 seconds and less then 10 seconds:
+   -> Run POST
+
+   Please note, that the POST test will take a while (approx. 1 min
+   on the 128MByte board). This is mainly due to the system memory
+   test.
+
+b) Release after more than 10 seconds:
+   -> Restore factory default settings
+
+   The factory default values are restored. The default environment
+   variables are restored (ipaddr, serverip...) and the board
+   specific values (ethaddr, eth1addr and serial#) are restored
+   to the environment from the I2C EEPROM. Also a bootline parameter
+   is added to the Linux bootline to signal the Linux kernel upon
+   the next startup, that the factory defaults should be restored.
+
+The command to check this sw-reset status and act accordingly is
+
+=> chkreset
+
+This command is added to the default "bootcmd", so that it is called
+automatically upon startup.
+
+Also, the 2 LED's are used to indicate the current status of this
+command (time passed since pushing the button). When the POST test
+will be run, the green LED will be switched off, and when the
+factory restore will be initiated, the reg LED will be switched off.
+
+
+Loggin of POST results:
+-----------------------
+
+The results of the POST tests are logged in a logbuffer located at the end
+of the onboard memory. It can be accessed with the U-Boot command "log":
+
+=> log show
+<4>POST memory PASSED
+<4>POST cache PASSED
+<4>POST cpu PASSED
+<4>POST uart PASSED
+<4>POST ethernet PASSED
+
+The DENX Linux kernel tree has support for this log buffer included. Exactly
+this buffer is used for logging of all kernel messages too. By enabling the
+compile time option "CONFIG_LOGBUFFER" this support is enabled. This way you
+can access the U-Boot log messages from Linux too.
+
+2007-08-10, Stefan Roese <sr@denx.de>