summaryrefslogtreecommitdiff
path: root/doc
diff options
context:
space:
mode:
authorwdenk <wdenk>2004-06-09 10:15:00 +0000
committerwdenk <wdenk>2004-06-09 10:15:00 +0000
commit48abe7bfab14c1e9bd4a9a1f9d2e094b6d16773c (patch)
tree9ef9bb8ccbe8f3a0421ad5947515038c43b4446e /doc
parent547b4cb25e585e154b5e84e33df3d157f786e305 (diff)
downloadu-boot-imx-48abe7bfab14c1e9bd4a9a1f9d2e094b6d16773c.zip
u-boot-imx-48abe7bfab14c1e9bd4a9a1f9d2e094b6d16773c.tar.gz
u-boot-imx-48abe7bfab14c1e9bd4a9a1f9d2e094b6d16773c.tar.bz2
Patch by Robert Schwebel, 13 May 2004:
Add 'imgextract' command: extract one part of a multi file image.
Diffstat (limited to 'doc')
-rw-r--r--doc/README.mpc85xxads23
1 files changed, 15 insertions, 8 deletions
diff --git a/doc/README.mpc85xxads b/doc/README.mpc85xxads
index 4c1686f..c49b2a8 100644
--- a/doc/README.mpc85xxads
+++ b/doc/README.mpc85xxads
@@ -5,10 +5,12 @@ Created 10/15/03
-----------------------------------------
0. Toolchain
-The Binutils in current ELDK toolchain will not support MPC85xx chip. You need
-use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
+The Binutils in ELDK toolchain 3.0 or earlier does not support the
+MPC85xx chip. You need use the newest binutils-2.14.tar.bz2 from
+http://ftp.gnu.org/gnu/binutils.
1. SWITCH SETTINGS & JUMPERS
+
1.1 First, make sure the board default setting is consistent with the document
shipped with your board. Then apply the following changes:
SW3[1-6]="all OFF" (boot from 32bit flash, no boot sequence is used)
@@ -19,11 +21,13 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
SW22[1-4]="OFF OFF ON OFF"
SW5[1-10[="ON ON OFF OFF OFF OFF OFF OFF OFF OFF"
J1 = "Enable Prog" (Make sure your flash is programmable for development)
+
1.2 If you want to test PCI functionality with a 33Mhz PCI card, you will
have to change the system clock from the default 66Mhz to 33Mhz by
setting SW15[1]="OFF" and SW17[8]="OFF". After that you may also need
double your platform clock(SW6) because the system clock is now only
- half of its original value.
+ half of its original value.
+
1.3 SW6 is a very important switch, it decides your platform clock and CPU
clock based on the on-board system clock(default 66MHz). Check the
document along with your board for details.
@@ -35,7 +39,7 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
between u-boot and linux kernel, you can customize it based on your
system requirements:
- 0x0000_0000 0x7fff_ffff DDR 2G
+ 0x0000_0000 0x7fff_ffff DDR 2G
0x8000_0000 0x9fff_ffff PCI MEM 512M
0xc000_0000 0xdfff_ffff Rapid IO 512M
0xe000_0000 0xe000_ffff CCSR 1M
@@ -52,7 +56,9 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
arch/ppc/configs/mpc8540_ads_defconfig
arch/ppc/configs/mpc8560_ads_defconfig
+
3. DEFINITIONS AND COMPILATION
+
3.1 Explanation on NEW definitions in include/configs/MPC8540ADS.h and include/
configs/MPC8560ADS.h
CONFIG_BOOKE BOOKE(e.g. Motorola MPC85xx, IBM 440, etc)
@@ -74,7 +80,6 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
if you can program the flash directly, undef this.
Other than the above definitions, the rest in the config files are straightforward.
-
3.2 Compilation
export CROSS_COMPILE=your-cross-compile-prefix(assuming you're using BASH shell)
cd u-boot
@@ -82,7 +87,9 @@ use the newest binutils-2.14.tar.bz2 from http://ftp.gnu.org/gnu/binutils.
make MPC8560ADS_config (or make MPC8540ADS_config)
make
+
4. Notes:
+
4.1 When connecting with kermit, the following commands must be present.in
your .kermrc file. These are especially important when booting as
MPC8560, as the serial console will not work without them:
@@ -93,7 +100,6 @@ set handshake none
set flow-control none
robust
-
4.2 Sometimes after U-Boot is up, the 'tftp' won't work well with TSEC ethernet. If that
happens, you can try the following steps to make network work:
MPC8560ADS>tftp 1000000 pImage
@@ -103,9 +109,9 @@ robust
>1
>. (to quit this memory operation)
MPC8560ADS>tftp 1000000 pImage
-4.3 If you're one of the early developers using the Rev1 8540/8560 chips, please use U-Boot
- 1.0.0, as the newer silicon will only support Rev2 and future revisions of 8540/8560.
+4.3 If you're one of the early developers using the Rev1 8540/8560 chips, please use U-Boot
+ 1.0.0, as the newer silicon will only support Rev2 and future revisions of 8540/8560.
4.4 Reflash U-boot Image using U-boot
@@ -116,6 +122,7 @@ robust
5. Screen dump:
+
5.1 MPC8540ADS board
U-Boot 1.0.0-pre (Oct 15 2003 - 13:40:33)