Merge branch 'master' of git://git.denx.de/u-boot-nand-flash

2 files changed, 64 insertions, 2 deletions

diff --git a/doc/README.nand b/doc/README.nand
index 913e9b5..b91f198 100644
--- a/doc/README.nand
+++ b/doc/README.nand
@@ -104,6 +104,16 @@ Configuration Options:
    CONFIG_SYS_MAX_NAND_DEVICE
       The maximum number of NAND devices you want to support.
 
+   CONFIG_SYS_NAND_MAX_ECCPOS
+      If specified, overrides the maximum number of ECC bytes
+      supported.  Useful for reducing image size, especially with SPL.
+      This must be at least 48 if nand_base.c is used.
+
+   CONFIG_SYS_NAND_MAX_OOBFREE
+      If specified, overrides the maximum number of free OOB regions
+      supported.  Useful for reducing image size, especially with SPL.
+      This must be at least 2 if nand_base.c is used.
+
    CONFIG_SYS_NAND_MAX_CHIPS
       The maximum number of NAND chips per device to be supported.
 
@@ -169,6 +179,59 @@ Configuration Options:
       Please convert your driver even if you don't need the extra
       flexibility, so that one day we can eliminate the old mechanism.
 
+
+   CONFIG_SYS_NAND_ONFI_DETECTION
+	Enables detection of ONFI compliant devices during probe.
+	And fetching device parameters flashed on device, by parsing
+	ONFI parameter page.
+
+   CONFIG_BCH
+	Enables software based BCH ECC algorithm present in lib/bch.c
+	This is used by SoC platforms which do not have built-in ELM
+	hardware engine required for BCH ECC correction.
+
+
+Platform specific options
+=========================
+   CONFIG_NAND_OMAP_GPMC
+	Enables omap_gpmc.c driver for OMAPx and AMxxxx platforms.
+	GPMC controller is used for parallel NAND flash devices, and can
+	do ECC calculation (not ECC error detection) for HAM1, BCH4, BCH8
+	and BCH16 ECC algorithms.
+
+   CONFIG_NAND_OMAP_ELM
+	Enables omap_elm.c driver for OMAPx and AMxxxx platforms.
+	ELM controller is used for ECC error detection (not ECC calculation)
+	of BCH4, BCH8 and BCH16 ECC algorithms.
+	Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
+	thus such SoC platforms need to depend on software library for ECC error
+	detection. However ECC calculation on such plaforms would still be
+	done by GPMC controller.
+
+   CONFIG_NAND_OMAP_ECCSCHEME
+	On OMAP platforms, this CONFIG specifies NAND ECC scheme.
+	It can take following values:
+	OMAP_ECC_HAM1_CODE_SW
+		1-bit Hamming code using software lib.
+		(for legacy devices only)
+	OMAP_ECC_HAM1_CODE_HW
+		1-bit Hamming code using GPMC hardware.
+		(for legacy devices only)
+	OMAP_ECC_BCH4_CODE_HW_DETECTION_SW
+		4-bit BCH code (unsupported)
+	OMAP_ECC_BCH4_CODE_HW
+		4-bit BCH code (unsupported)
+	OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
+		8-bit BCH code with
+		- ecc calculation using GPMC hardware engine,
+		- error detection using software library.
+		- requires CONFIG_BCH to enable software BCH library
+		(For legacy device which do not have ELM h/w engine)
+	OMAP_ECC_BCH8_CODE_HW
+		8-bit BCH code with
+		- ecc calculation using GPMC hardware engine,
+		- error detection using ELM hardware engine.
+
 NOTE:
 =====
 
diff --git a/doc/README.omap3 b/doc/README.omap3
index 1fbe79d..a62c357 100644
--- a/doc/README.omap3
+++ b/doc/README.omap3
@@ -161,8 +161,7 @@ BCH8
 
 To enable hardware assisted BCH8 (8-bit BCH [Bose, Chaudhuri, Hocquenghem]) on
 OMAP3 devices we can use the BCH library in lib/bch.c. To do so add CONFIG_BCH
-to enable the library and CONFIG_NAND_OMAP_BCH8 to to enable hardware assisted
-syndrom generation to your board config.
+and set CONFIG_NAND_OMAP_ECCSCHEME=5 (refer README.nand) for selecting BCH8_SW.
 The NAND OOB layout is the same as in linux kernel, if the linux kernel BCH8
 implementation for OMAP3 works for you so the u-boot version should also.
 When you require the SPL to read with BCH8 there are two more configs to