powerpc: mpc85xx: Support booting from SD Card with SPL

The code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.

The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
	* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
	ddr spd code can get the interleaving mode setting in env. It loads
	final uboot image from offset 96KB.
	* final uboot image, size is variable depends on the functions enabled.

Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>

1 files changed, 81 insertions, 0 deletions

diff --git a/doc/README.mpc85xx-sd-spi-boot b/doc/README.mpc85xx-sd-spi-boot
new file mode 100644
index 0000000..d5043cc
--- /dev/null
+++ b/doc/README.mpc85xx-sd-spi-boot
@@ -0,0 +1,81 @@
+----------------------------------------
+Booting from On-Chip ROM (eSDHC or eSPI)
+----------------------------------------
+
+boot_format is a tool to write SD bootable images to a filesystem and build
+SD/SPI images to a binary file for writing later.
+
+When booting from an SD card/MMC, boot_format puts the configuration file and
+the RAM-based U-Boot image on the card.
+When booting from an EEPROM, boot_format generates a binary image that is used
+to boot from this EEPROM.
+
+Where to get boot_format:
+========================
+
+you can browse it online at:
+http://git.freescale.com/git/cgit.cgi/ppc/sdk/boot-format.git/
+
+Building
+========
+
+Run the following to build this project
+
+	$ make
+
+Execution
+=========
+
+boot_format runs under a regular Linux machine and requires a super user mode
+to run. Execute boot_format as follows.
+
+For building SD images by writing directly to a file system on SD media:
+
+	$ boot_format $config u-boot.bin -sd $device
+
+Where $config is the included config.dat file for your platform and $device
+is the target block device for the SD media on your computer.
+
+For build binary images directly a local file:
+
+	$ boot_format $config u-boot.bin -spi $file
+
+Where $file is the target file. Also keep in mind the u-boot.bin file needs
+to be the u-boot built for your particular platform and target media.
+
+Example: To generate a u-boot.bin for a P1022DS booting from SD, run the
+following in the u-boot repository:
+
+	$ make P1022DS_SDCARD
+
+Configuration Files
+===================
+
+Below are the configuration files to be used with a particular platform. Keep
+in mind that some of these config files are tied to the platforms DDR speed.
+Please see the SoC reference manual for more documentation.
+
+P1022DS		config_sram_p1022ds.dat
+P2020DS		config_sram_p2020ds.dat
+P2010DS		config_sram_p2020ds.dat
+P1020RDB	config_ddr2_1g_p1020rdb_533M.dat
+P1020RDB	config_ddr2_1g_p1020rdb_667M.dat
+P2020RDB	config_ddr2_1g_p2020rdb_800M.dat
+P2020RDB	config_ddr2_1g_p2020rdb_667M.dat
+P2020RDB	config_ddr3_1gb_64bit_p2020rdb_pc.dat
+P2010RDB	config_ddr3_1gb_64bit_p2020rdb_pc.dat
+P1020RDB	config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+P1011RDB	config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+P1010RDB	config_ddr3_1gb_p1010rdb_800M.dat
+P1014RDB	config_ddr3_1gb_p1014rdb_800M.dat
+P1021RDB	config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+P1012RDB	config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+P1022DS		config_ddr3_2gb_p1022ds.dat
+P1013DS		config_ddr3_2gb_p1022ds.dat
+P1024RDB	config_ddr3_1gb_p1_p2_rdb_pc_667M.dat
+P1013RDB	config_ddr3_1gb_p1_p2_rdb_pc_667M.dat
+P1025RDB	config_ddr3_1gb_p1_p2_rdb_pc_667M.dat
+P1016RDB	config_ddr3_1gb_p1_p2_rdb_pc_667M.dat
+P1020UTM	config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+P1020MBG	config_ddr3_1gb_p1_p2_rdb_pc_800M.dat
+MPC8536DS	config_ddr2_512m_mpc8536ds_667M.dat