Merge branch 'master' of git://git.denx.de/u-boot-arm

* 'master' of git://git.denx.de/u-boot-arm: (212 commits)
  ARM: cache: Move the cp15 CR register read before flushing the cache.
  ARM: introduce arch_early_init_r()
  PXA: Enable CONFIG_PREBOOT on zipitz2
  ARM: mx28: Remove CONFIG_ARCH_CPU_INIT
  No need to define CONFIG_ARCH_CPU_INIT.
  add new board vl_ma2sc
  MTD: SPEAr SMI: Add write support for length < 4 bytes
  i2c: designware_i2c.c: Add support for the "i2c probe" command
  rtc/m41t62: Add support for M41T82 with HT (Halt Update)
  SPL: ARM: spear: Add SPL support for SPEAr600 platform
  Makefile: Add u-boot.spr build target (SPEAr)
  SPL: ARM: spear: Remove some objects from SPL build
  SPL: lib/Makefile: Add crc32.c to SPL build
  SPL: common/Makefile: Add image.c to SPL build
  arm: Don't use printf() in SPL builds
  GPIO: Add SPEAr GPIO driver
  net: Multiple updates/enhancements to designware.c
  cleanup/SPEAr: Define configuration flags more elegantly
  cleanup/SPEAr: Remove unnecessary parenthesis
  SPEAr: Correct SoC ID offset in misc configuration space
  SPEAr: explicitly select clk src for UART
  SPEAr: Remove CONFIG_MTD_NAND_VERIFY_WRITE to speed up NAND access
  SPEAr: Enable ONFI nand flash detection for spear3xx and 6xx and evb
  SPEAr: Enable CONFIG_SYS_FLASH_EMPTY_INFO macro
  SPEAr: Correct the definition of CONFIG_SYS_MONITOR_BASE
  SPEAr: Enable CONFIG_SYS_FLASH_PROTECTION
  SPEAr: Enable dcache for fast file transfer
  SPEAr: Enable autoneg for ethernet
  SPEAr: Enable udc and usb-console support only for usbtty configuration
  SPEAr: Enable usb device high speed support
  SPEAr: Initialize SNOR in early_board_init_f
  SPEAr: Change the default environment variables
  SPEAr: Remove unused flag (CONFIG_SYS_HZ_CLOCK)
  SPEAr: Add configuration options for spear3xx and spear6xx boards
  SPEAr: Add basic arch related support for SPEAr SoCs
  SPEAr: Add interface information in initialization
  SPEAr: Add macb driver support for spear310 and spear320
  SPEAr: Configure network support for spear SoCs
  SPEAr: Place ethaddr write and read within CONFIG_CMD_NET
  SPEAr: Eliminate dependency on Xloader table
  SPEAr: Fix ARM relocation support
  st_smi: Fixed page size for Winbond W25Q128FV flash
  st_smi: Change timeout loop implementation
  st_smi: Fix bug in flash_print_info()
  st_smi: Change the flash probing method
  st_smi: Removed no needed dependency on ST_M25Pxx_ID
  st_smi: Fix smi read status
  st_smi: Move status register read before modifying ctrl register
  st_smi: Read status until timeout happens
  st_smi: Enhance the error handling
  st_smi: Change SMI timeout values
  st_smi: Return error in case TFF is not set
  st_smi: Add support for SPEAr SMI driver
  mtd/NAND: Remove obsolete SPEAr specific NAND drivers
  SPEAr: Configure FSMC driver for NAND interface
  mtd/NAND: Add FSMC driver support
  arm/km: remove calls to kw_gpio_* in board_early_init_f
  arm/km: add implementation for read_dip_switch
  arm/km: support the 2 PCIe fpga resets
  arm/km: skip FPGA config when already configured
  arm/km: redefine piggy 4 reg names to avoid conflicts
  arm/km: cleanup km_kirkwood boards
  arm/km: enable BOCO2 FPGA download support
  arm/km: remove portl2.h and use km_kirkwood instead
  arm/km: convert mgcoge3un target to km_kirkwood
  arm/km: add kmcoge5un board support
  arm/km: add kmnusa board support
  arm: bugfix: save_boot_params_default accesses uninitalized stack when -O0
  cm-t35: fix incorrect NAND_ECC layout selection
  ARM: OMAP4/5: Do not configure non essential pads, clocks, dplls.
  ARM: OMAP4/5: Move USB pads to essential list.
  ARM: OMAP4/5: Move USB clocks to essential group.
  ARM: OMAP4/5: Move gpmc clocks to essential group.
  ARM: OMAP4+: Move external phy initialisations to arch specific place.
  omap4: Use a smaller M,N couple for IVA DPLL
  da850/omap-l138: Enable auto negotiation in RMII mode
  omap: am33xx: accomodate input clocks other than 24 Mhz
  omap: emif: fix bug in manufacturer code test
  omap: emif: deal with rams that return duplicate mr data on all byte lanes
  OMAP4+: Force DDR in self-refresh after warm reset
  OMAP4+: Handle sdram init after warm reset
  ARM: OMAP3+: Detect reset type
  arm: bugfix: Move vector table before jumping relocated code
  Kirkwood: Add support for Ka-Ro TK71
  arm/km: use spi claim bus to switch between SPI and NAND
  arm/kirkwood: protect the ENV_SPI #defines
  ARM: don't probe PHY address for LaCie boards
  lacie_kw: fix CONFIG_SYS_KWD_CONFIG for inetspace_v2
  lacie_kw: fix SDRAM banks number for net2big_v2
  Kirkwood: add lschlv2 and lsxhl board support
  net: add helper to generate random mac address
  net: use common rand()/srand() functions
  lib: add rand() function
  kwboot: boot kirkwood SoCs over a serial link
  kw_spi: add weak functions board_spi_claim/release_bus
  kw_spi: support spi_claim/release_bus functions
  kw_spi: backup and reset the MPP of the chosen CS pin
  kirkwood: fix calls to kirkwood_mpp_conf
  kirkwood: add save functionality kirkwood_mpp_conf function
  km_arm: use filesize for erase in update command
  arm/km: enable mii cmd
  arm/km: remove CONFIG_RESET_PHY_R
  arm/km: change maintainer for mgcoge3un
  arm/km: fix wrong comment in SDRAM config for mgcoge3un
  arm/km: use ARRAY_SIZE macro
  arm/km: rename CONFIG option CONFIG_KM_DEF_ENV_UPDATE
  arm/km: add piggy mac adress offset for mgcoge3un
  arm/km: add board type to boards.cfg
  AT91SAM9*: Change kernel address in dataflash to match u-boot's size
  ATMEL/PIO: Enable new feature of PIO on Atmel device
  ehci-atmel: fix compiler warning
  AT91: at91sam9m10g45ek : Enable EHCI instead OHCI
  Atmel : usb : add EHCI driver for Atmel SoC
  Fix: AT91SAM9263 nor flash usage
  Fix: broken boot message at serial line on AT91SAM9263-EK board
  i.MX6 USDHC: Use the ESDHC clock
  mx28evk: Fix boot by adjusting HW_DRAM_CTL29 register
  i.MX28: Add function to adjust memory parameters
  mx28evk: Fix PSWITCH key position
  mx53smd: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53loco: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53evk: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53ard: Remove CONFIG_SYS_I2C_SLAVE definition
  mx35pdk: Remove CONFIG_SYS_I2C_SLAVE definition
  imx31_phycore: Remove CONFIG_SYS_I2C_SLAVE definition
  mx53ard: Remove unused CONFIG_MII_GASKET
  mx6: Avoid writing to read-only bits in imximage.cfg
  m28evk: use same notation to alloc the 128kB stack
  ...

Signed-off-by: Wolfgang Denk <wd@denx.de>

4 files changed, 150 insertions, 15 deletions

diff --git a/doc/README.mx28evk b/doc/README.mx28evk
index c6c3d37..571dfda 100644
--- a/doc/README.mx28evk
+++ b/doc/README.mx28evk
@@ -17,7 +17,7 @@ Jumper configuration
 To boot MX28EVK from an SD card, set the boot mode DIP switches as:
 
    * Boot Mode Select: 1 0 0 1 (Boot from SD card Slot 0 - U42)
-   * JTAG PSWITCH RESET: To the left (reset enabled)
+   * JTAG PSWITCH RESET: To the right (reset disabled)
    * Battery Source: Down
    * Wall 5V: Up
    * VDD 5V: To the left (off)
diff --git a/doc/README.spear b/doc/README.spear
index a8b1052..0789b3f 100644
--- a/doc/README.spear
+++ b/doc/README.spear
@@ -6,9 +6,10 @@ SPEAr600 is also known as SPEArPlus and SPEAr300 is also known as SPEArBasic
 The SPEAr SoC family embeds a customizable logic that can be programmed
 one-time by a customer at silicon mask level (i.e. not at runtime!).
 
-We are now adding the support in u-boot for two SoC: SPEAr600 and SPEAr3xx.
+U-Boot supports four SoCs: SPEAr600, SPEAr3xx
 
-All 4 SoCs share common peripherals.
+All 4 SoCs (SPEAr3xx and SPEAr600) share common peripherals. SPEAr300 and
+SPEAr600 do not have EMI.
 
 1. ARM926ejs core based (sp600 has two cores, the 2nd handled only in Linux)
 2. FastEthernet (sp600 has Gbit version, but same controller - GMAC)
@@ -22,7 +23,7 @@ All 4 SoCs share common peripherals.
 10. others ..
 
 Everything is supported in Linux.
-u-boot is not currently supporting all peripeharls (just a few as listed below).
+u-boot is currently not supporting all peripeharls (just a few as listed below).
 1. USB Device
 2. NAND controller (FSMC)
 3. Serial Memory Interface
@@ -31,18 +32,43 @@ u-boot is not currently supporting all peripeharls (just a few as listed below).
 5. UART
 
 Build options
-	make spear600_config
+	make spear320_config
+		spear320 build with environment variables placed at default
+		location i.e. Serial NOR device
+	make spear320_pnor_config
+		This option generates a uboot image that supports emi controller
+		for CFI compliant parallel NOR flash. Environment variables are
+		placed in Parallel NOR device
+	make spear320_nand_config
+		spear320 build with environment variables placed in NAND device
+	make spear320_usbtty_config
+		spear320 build with usbtty terminal as default and environment
+		placed at default location
+	make spear320_usbtty_pnor_config
+		spear320 build with usbtty terminal as default and environment
+		placed in pnor device
+	make spear320_usbtty_nand_config
+		Build with usbtty terminal as default and environment placed in
+		NAND device
 	make spear300_config
+	make spear300_nand_config
+	make spear300_usbtty_config
+	make spear300_usbtty_nand_config
 	make spear310_config
-	make spear320_config
-
-Further options
-	make ENV=NAND (supported by all 4 SoCs)
-	- This option generates a uboot image that saves environment inn NAND
+	make spear310_pnor_config
+	make spear310_nand_config
+	make spear310_usbtty_config
+	make spear310_usbtty_pnor_config
+	make spear310_usbtty_nand_config
+	make spear600_config
+	make spear600_nand_config
+	make spear600_usbtty_config
+	make spear600_usbtty_nand_config
 
-	make CONSOLE=USB (supported by all 4 SoCs)
-	- This option generates a uboot image for using usbdevice as a tty i/f
+Mac id storage and retrieval in spear platforms
 
-	make FLASH=PNOR (supported by SPEAr310 and SPEAr320)
-	- This option generates a uboot image that supports emi controller for
-	CFI compliant parallel NOR flash
+Please read doc/README.enetaddr for the implementation guidelines for mac id
+usage. Basically, environment has precedence over board specific storage. The
+ethaddr beeing used for the network interface is always taken only from
+environment variables. Although, we can check the mac id programmed in i2c
+memory by using chip_config command
diff --git a/doc/README.switch_config b/doc/README.switch_config
new file mode 100644
index 0000000..f890373
--- /dev/null
+++ b/doc/README.switch_config
@@ -0,0 +1,25 @@
+On the enbw_cmc board is a KSZ8864RMN switch which needs
+configured through spi before working. This is done on
+startup from u-boot through a config file stored at an
+address specified in the "hwconfig" environment variable,
+subcommand "config".
+
+For example on the enbw_cmc board:
+
+hwconfig=switch:lan=on,pwl=off,config=0x60160000
+
+The file has the following structure:
+
+- a comment starts with a '#' or a ';' and ends with a newline
+- The switch needs for its config a reg/value pair, so we
+  have two columns in the file:
+    reg  : contains the register address
+    value: contains a 8 bit register value
+  This 2 columns are seperated through space or tab.
+
+example (minimal configuration on the enbw_cmc board):
+
+;reg    value   comment
+;-----------------------------------------
+0x01	0x00
+0x01	0x01    ; Start Switch with this configuration
diff --git a/doc/kwboot.1 b/doc/kwboot.1
new file mode 100644
index 0000000..ed08398
--- /dev/null
+++ b/doc/kwboot.1
@@ -0,0 +1,84 @@
+.TH KWBOOT 1 "2012-05-19"
+
+.SH NAME
+kwboot \- Boot Marvell Kirkwood SoCs over a serial link.
+.SH SYNOPSIS
+.B kwboot
+.RB [ "-b \fIimage\fP" ]
+.RB [ "-p" ]
+.RB [ "-t" ]
+.RB [ "-B \fIbaudrate\fP" ]
+.RB \fITTY\fP
+.SH "DESCRIPTION"
+
+The \fBmkimage\fP program boots boards based on Marvell's Kirkwood
+platform over their integrated UART. Boot image files will typically
+contain a second stage boot loader, such as U-Boot. The image file
+must conform to Marvell's BootROM firmware image format
+(\fIkwbimage\fP), created using a tool such as \fBmkimage\fP.
+
+Following power-up or a system reset, system BootROM code polls the
+UART for a brief period of time, sensing a handshake message which
+initiates an image upload. This program sends this boot message until
+it receives a positive acknowledgement. The image is transfered using
+Xmodem.
+
+Additionally, this program implements a minimal terminal mode, which
+can be used either standalone, or entered immediately following boot
+image transfer completion. This is often useful to catch early boot
+messages, or to manually interrupt a default boot procedure performed
+by the second-stage loader.
+
+.SH "OPTIONS"
+
+.TP
+.BI "\-b \fIimage\fP"
+Handshake; then upload file \fIimage\fP over \fITTY\fP.
+
+Note that for the encapsulated boot code to be executed, \fIimage\fP
+must be of type "UART boot" (0x69). Boot images of different types,
+such as backup images of vendor firmware downloaded from flash memory
+(type 0x8B), will not work (or not as expected). See \fB-p\fP for a
+workaround.
+
+This mode writes handshake status and upload progress indication to
+stdout.
+
+.TP
+.BI "\-p"
+In combination with \fB-b\fP, patches the header in \fIimage\fP prior
+to upload, to "UART boot" type.
+
+This option attempts on-the-fly conversion of some none-UART image
+types, such as images which were originally formatted to be stored in
+flash memory.
+
+Conversion is performed in memory. The contents of \fIimage\fP will
+not be altered.
+
+.TP
+.BI "\-t"
+Run a terminal program, connecting standard input and output to
+.RB \fITTY\fP.
+
+If used in combination with \fB-b\fP, terminal mode is entered
+immediately following a successful image upload.
+
+If standard I/O streams connect to a console, this mode will terminate
+after receiving 'ctrl-\\' followed by 'c' from console input.
+
+.TP
+.BI "\-B \fIbaudrate\fP"
+Adjust the baud rate on \fITTY\fP. Default rate is 115200.
+
+.SH "SEE ALSO"
+.PP
+\fBmkimage\fP(1)
+
+.SH "AUTHORS"
+
+Daniel Stodden <daniel.stodden@gmail.com>
+.br
+Luka Perkov <uboot@lukaperkov.net>
+.br
+David Purdy <david.c.purdy@gmail.com>