power: Add support for TPS65090 PMU chip.

This adds driver support for the TPS65090 PMU. Support includes
hooking into the pmic infrastructure  so that the pmic commands
can be used on the console. The TPS65090 supports the following
functionality:

- fet enable/disable/querying
- getting and setting of charge state

Even though it is connected to the pmic infrastructure it does
not hook into the pmic charging charging infrastructure.

The device tree binding is from Linux, but only a small subset of
functionality is supported.

Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Katie Roberts-Hoffman <katierh@chromium.org>
Signed-off-by: Rong Chang <rongchang@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

2 files changed, 139 insertions, 0 deletions

diff --git a/doc/device-tree-bindings/power/tps65090.txt b/doc/device-tree-bindings/power/tps65090.txt
new file mode 100644
index 0000000..8e5e0d3
--- /dev/null
+++ b/doc/device-tree-bindings/power/tps65090.txt
@@ -0,0 +1,17 @@
+TPS65090 Frontend PMU with Switchmode Charger
+
+Required Properties:
+-compatible: "ti,tps65090-charger"
+
+Optional Properties:
+-ti,enable-low-current-chrg: Enables charging when a low current is detected
+ while the default logic is to stop charging.
+
+This node is a subnode of the tps65090 PMIC.
+
+Example:
+
+	tps65090-charger {
+		compatible = "ti,tps65090-charger";
+		ti,enable-low-current-chrg;
+	};
diff --git a/doc/device-tree-bindings/regulator/tps65090.txt b/doc/device-tree-bindings/regulator/tps65090.txt
new file mode 100644
index 0000000..313a60b
--- /dev/null
+++ b/doc/device-tree-bindings/regulator/tps65090.txt
@@ -0,0 +1,122 @@
+TPS65090 regulators
+
+Required properties:
+- compatible: "ti,tps65090"
+- reg: I2C slave address
+- interrupts: the interrupt outputs of the controller
+- regulators: A node that houses a sub-node for each regulator within the
+  device. Each sub-node is identified using the node's name, with valid
+  values listed below. The content of each sub-node is defined by the
+  standard binding for regulators; see regulator.txt.
+  dcdc[1-3], fet[1-7] and ldo[1-2] respectively.
+- vsys[1-3]-supply: The input supply for DCDC[1-3] respectively.
+- infet[1-7]-supply: The input supply for FET[1-7] respectively.
+- vsys-l[1-2]-supply: The input supply for LDO[1-2] respectively.
+
+Optional properties:
+- ti,enable-ext-control: This is applicable for DCDC1, DCDC2 and DCDC3.
+  If DCDCs are externally controlled then this property should be there.
+- "dcdc-ext-control-gpios: This is applicable for DCDC1, DCDC2 and DCDC3.
+  If DCDCs are externally controlled and if it is from GPIO then GPIO
+  number should be provided. If it is externally controlled and no GPIO
+  entry then driver will just configure this rails as external control
+  and will not provide any enable/disable APIs.
+
+Each regulator is defined using the standard binding for regulators.
+
+Example:
+
+	tps65090@48 {
+		compatible = "ti,tps65090";
+		reg = <0x48>;
+		interrupts = <0 88 0x4>;
+
+		vsys1-supply = <&some_reg>;
+		vsys2-supply = <&some_reg>;
+		vsys3-supply = <&some_reg>;
+		infet1-supply = <&some_reg>;
+		infet2-supply = <&some_reg>;
+		infet3-supply = <&some_reg>;
+		infet4-supply = <&some_reg>;
+		infet5-supply = <&some_reg>;
+		infet6-supply = <&some_reg>;
+		infet7-supply = <&some_reg>;
+		vsys_l1-supply = <&some_reg>;
+		vsys_l2-supply = <&some_reg>;
+
+		regulators {
+			dcdc1 {
+				regulator-name = "dcdc1";
+				regulator-boot-on;
+				regulator-always-on;
+				ti,enable-ext-control;
+				dcdc-ext-control-gpios = <&gpio 10 0>;
+			};
+
+			dcdc2 {
+				regulator-name = "dcdc2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			dcdc3 {
+				regulator-name = "dcdc3";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet1 {
+				regulator-name = "fet1";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet2 {
+				regulator-name = "fet2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet3 {
+				regulator-name = "fet3";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet4 {
+				regulator-name = "fet4";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet5 {
+				regulator-name = "fet5";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet6 {
+				regulator-name = "fet6";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			fet7 {
+				regulator-name = "fet7";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo1 {
+				regulator-name = "ldo1";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+
+			ldo2 {
+				regulator-name = "ldo2";
+				regulator-boot-on;
+				regulator-always-on;
+			};
+		};
+	};