doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

1 files changed, 0 insertions, 123 deletions

diff --git a/doc/README.sh7785lcr b/doc/README.sh7785lcr
deleted file mode 100644
index 56455fc..0000000
--- a/doc/README.sh7785lcr
+++ /dev/null
@@ -1,123 +0,0 @@
-========================================
-Renesas Technology R0P7785LC0011RL board
-========================================
-
-This board specification:
-=========================
-
-The R0P7785LC0011RL(board config name:sh7785lcr) has the following device:
-
- - SH7785 (SH-4A)
- - DDR2-SDRAM 512MB
- - NOR Flash 64MB
- - 2D Graphic controller
- - SATA controller
- - Ethernet controller
- - USB host/peripheral controller
- - SD controller
- - I2C controller
- - RTC
-
-This board has 2 physical memory maps. It can be changed with DIP switch(S2-5).
-
- phys address			| S2-5 = OFF	| S2-5 = ON
- -------------------------------+---------------+---------------
- 0x00000000 - 0x03ffffff(CS0)	| NOR Flash	| NOR Flash
- 0x04000000 - 0x05ffffff(CS1)	| PLD		| PLD
- 0x06000000 - 0x07ffffff(CS1)	| reserved	| I2C
- 0x08000000 - 0x0bffffff(CS2)	| USB		| DDR SDRAM
- 0x0c000000 - 0x0fffffff(CS3)	| SD		| DDR SDRAM
- 0x10000000 - 0x13ffffff(CS4)	| SM107		| SM107
- 0x14000000 - 0x17ffffff(CS5)	| I2C		| USB
- 0x18000000 - 0x1bffffff(CS6)	| reserved	| SD
- 0x40000000 - 0x5fffffff	| DDR SDRAM	| (cannot use)
-
-
-configuration for This board:
-=============================
-
-You can choose configuration as follows:
-
- - make sh7785lcr_config
- - make sh7785lcr_32bit_config
-
-When you use "make sh7785lcr_config", there is build U-Boot for 29-bit
-address mode. This mode can use 128MB DDR-SDRAM.
-
-When you use "make sh7785lcr_32bit_config", there is build U-Boot for 32-bit
-extended address mode. This mode can use 384MB DDR-SDRAM. And if you run
-"pmb" command, this mode can use 512MB DDR-SDRAM.
-
- * 32-bit extended address mode PMB mapping *
-  a) on start-up
-   virt		| phys		| size		| device
-   -------------+---------------+---------------+---------------
-   0x88000000	| 0x48000000	| 384MB		| DDR-SDRAM (Cacheable)
-   0xa0000000	| 0x00000000	| 64MB		| NOR Flash
-   0xa4000000	| 0x04000000	| 16MB		| PLD
-   0xa6000000	| 0x08000000	| 16MB		| USB
-   0xa8000000	| 0x48000000	| 384MB		| DDR-SDRAM (Non-cacheable)
-
-  b) after "pmb" command
-   virt		| phys		| size		| device
-   -------------+---------------+---------------+---------------
-   0x80000000	| 0x40000000	| 512MB		| DDR-SDRAM (Cacheable)
-   0xa0000000	| 0x40000000	| 512MB		| DDR-SDRAM (Non-cacheable)
-
-
-This board specific command:
-============================
-
-This board has the following its specific command:
-
- - hwtest
- - printmac
- - setmac
- - pmb (sh7785lcr_32bit_config only)
-
-
-1. hwtest
-
-This is self-check command. This command has the following options:
-
- - all		: test all hardware
- - pld		: output PLD version
- - led		: turn on LEDs
- - dipsw	: test DIP switch
- - sm107	: output SM107 version
- - net		: check RTL8110 ID
- - sata		: check SiI3512 ID
- - net		: output PCI slot device ID
-
-i.e)
-=> hwtest led
-turn on LEDs 3, 5, 7, 9
-turn on LEDs 4, 6, 8, 10
-
-=> hwtest net
-Ethernet OK
-
-
-2. printmac
-
-This command outputs MAC address of this board.
-
-i.e)
-=> printmac
-MAC = 00:00:87:**:**:**
-
-
-3. setmac
-
-This command writes MAC address of this board.
-
-i.e)
-=> setmac 00:00:87:**:**:**
-
-
-4. pmb
-
-This command change PMB for DDR-SDRAM all mapping. However you cannot use
-NOR Flash and USB Host on U-Boot when you run this command.
-i.e)
-=> pmb