summaryrefslogtreecommitdiff
path: root/doc/README.mx6qsabrelite
diff options
context:
space:
mode:
authorJason Liu <jason.hui@linaro.org>2011-12-29 06:34:19 +0000
committerAlbert ARIBAUD <albert.u.boot@aribaud.net>2012-01-16 08:40:10 +0100
commitbc5833c49a5514237cb18177c0f79df0d564b7da (patch)
treebd6bb817757ef1002551b911bbf43aa4531e2e7e /doc/README.mx6qsabrelite
parentf2f7745825ee5f6bae5b480c8e9c6641a7ffa73b (diff)
downloadu-boot-imx-bc5833c49a5514237cb18177c0f79df0d564b7da.zip
u-boot-imx-bc5833c49a5514237cb18177c0f79df0d564b7da.tar.gz
u-boot-imx-bc5833c49a5514237cb18177c0f79df0d564b7da.tar.bz2
i.mx: i.mx6q: add the initial support for i.mx6q Sabre Lite board
Add the initial support for Freescale i.MX6Q Sabre Lite board Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by: Jason Liu <jason.hui@linaro.org> CC: Eric Nelson <eric.nelson@boundarydevices.com>
Diffstat (limited to 'doc/README.mx6qsabrelite')
-rw-r--r--doc/README.mx6qsabrelite67
1 files changed, 67 insertions, 0 deletions
diff --git a/doc/README.mx6qsabrelite b/doc/README.mx6qsabrelite
new file mode 100644
index 0000000..4add2bf
--- /dev/null
+++ b/doc/README.mx6qsabrelite
@@ -0,0 +1,67 @@
+U-Boot for the Freescale i.MX6q SabreLite board
+
+This file contains information for the port of U-Boot to the Freescale
+i.MX6q SabreLite board.
+
+1. Boot source, boot from SD card
+---------------------------------
+
+The recent mainline U-Boot for the Freescale i.MX6q SabreLite board supports
+boot from SD card only. However, by default, the early version of SabreLite
+boards boot from the SPI NOR flash. These boards need to be reflashed with
+a small SD card loader to support boot from SD card. This small SD card loader
+will be flashed into the SPI NOR. The board will still boot from SPI NOR, but
+the loader will in turn request the BootROM to load the U-Boot from SD card.
+At the moment of writing, please check with Freescale on the availablity of
+this small SD loader binary.
+
+To update the SPI-NOR on the SabreLite board without the Freescale
+manufacturing tool use the following procedure:
+
+1. Write this SD card loader onto a large SD card using:
+
+ sudo dd if=MX6_SPI_to_SD_loader.bin of=/dev/sXx
+
+Note: Replace sXx with the device representing the SD card in your system.
+
+Note: This writes SD card loader at address 0
+
+2. Put this SD card into the slot for the large SD card (SD3 on the bottom of
+the board)
+
+3. Power-up the SabreLite, press 'space' to enter command mode in the U-Boot
+(the default one the board is shipped with, starting from the SPI NOR) and
+enter the following commands:
+
+ MX6Q SABRELITE U-Boot > mmc dev 0
+ MX6Q SABRELITE U-Boot > mmc read 0x10800000 0 200
+ MX6Q SABRELITE U-Boot > sf probe 1
+ MX6Q SABRELITE U-Boot > sf erase 0 0x40000
+ MX6Q SABRELITE U-Boot > sf write 0x10800000 0 0x40000
+
+4. done.
+
+In case you somehow do not succeed with this procedure you will have to use
+the Freescale manufacturing tool in order to reflash the SPI-NOR.
+
+Note: The board now boots from full size SD3 on the bottom of the board. NOT
+ the micro SD4/BOOT slot on the top of the board. I.e. you have to use
+ full size SD cards.
+
+This information is taken from
+
+https://wiki.linaro.org/Boards/MX6QSabreLite
+
+2. Build
+--------
+
+To build U-Boot for the SabreLite board:
+
+ make mx6qsabrelite_config
+ make u-boot.imx
+
+To copy the resulting u-boot.imx to the SD card:
+
+ sudo dd if=u-boot.imx of=/dev/sXx bs=512 seek=2&&sudo sync
+
+Note: Replace sXx with the device representing the SD card in your system.