doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

1 files changed, 0 insertions, 72 deletions

diff --git a/doc/README.mx6qsabrelite b/doc/README.mx6qsabrelite
deleted file mode 100644
index 6f2f534..0000000
--- a/doc/README.mx6qsabrelite
+++ /dev/null
@@ -1,72 +0,0 @@
-U-Boot for the Freescale i.MX6q SabreLite board
-
-This file contains information for the port of U-Boot to the Freescale
-i.MX6q SabreLite board.
-
-1. Boot source, boot from SD card
----------------------------------
-
-The recent mainline U-Boot for the Freescale i.MX6q SabreLite board supports
-boot from SD card only. However, by default, the SabreLite
-boards boot from the SPI NOR flash. These boards need to be reflashed with
-a small SD card loader to support boot from SD card. This small SD card loader
-will be flashed into the SPI NOR. The board will still boot from SPI NOR, but
-the loader will in turn request the BootROM to load the U-Boot from SD card.
-
-The SD card loader is available from
-
-https://wiki.linaro.org/Boards/MX6QSabreLite
-
-under a open-source 3-clause BSD license.
-
-To update the SPI-NOR on the SabreLite board without the Freescale
-manufacturing tool use the following procedure:
-
-1. Write this SD card loader onto a large SD card using:
-
- sudo dd if=iMX6DQ_SPI_to_uSDHC3.bin of=/dev/sXx
-
-Note: Replace sXx with the device representing the SD card in your system.
-
-Note: This writes SD card loader at address 0
-
-2. Put this SD card into the slot for the large SD card (SD3 on the bottom of
-the board). Make sure SW1 switch is at position "00", so that it can boot
-from the fuses.
-
-3. Power-up the SabreLite, press 'space' to enter command mode in the U-Boot
-(the default one the board is shipped with, starting from the SPI NOR) and
-enter the following commands:
-
- MX6Q SABRELITE U-Boot > mmc dev 0
- MX6Q SABRELITE U-Boot > mmc read 0x10800000 0 200
- MX6Q SABRELITE U-Boot > sf probe 1
- MX6Q SABRELITE U-Boot > sf erase 0 0x40000
- MX6Q SABRELITE U-Boot > sf write 0x10800000 0 0x40000
-
-4. done.
-
-In case you somehow do not succeed with this procedure you will have to use
-the Freescale manufacturing tool in order to reflash the SPI-NOR.
-
-Note: The board now boots from full size SD3 on the bottom of the board. NOT
-      the micro SD4/BOOT slot on the top of the board. I.e. you have to use
-      full size SD cards.
-
-This information is taken from
-
-https://wiki.linaro.org/Boards/MX6QSabreLite
-
-2. Build
---------
-
-To build U-Boot for the SabreLite board:
-
- make mx6qsabrelite_config
- make u-boot.imx
-
-To copy the resulting u-boot.imx to the SD card:
-
- sudo dd if=u-boot.imx of=/dev/sXx bs=512 seek=2&&sudo sync
-
-Note: Replace sXx with the device representing the SD card in your system.