doc: cleanup - move board READMEs into respective board directories

Also drop a few files referring to no longer / not yet supported
boards.

Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Jason Jin <jason.jin@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Daniel Schwierzeck <daniel.schwierzeck@googlemail.com>

1 files changed, 0 insertions, 74 deletions

diff --git a/doc/README.ag101 b/doc/README.ag101
deleted file mode 100644
index 46fc637..0000000
--- a/doc/README.ag101
+++ /dev/null
@@ -1,74 +0,0 @@
-Andes Technology SoC AG101
-==========================
-
-AG101 is the first SoC produced by Andes Technology using N1213 CPU core.
-AG101 has integrated both AHB and APB bus and many periphals for application
-and product development.
-
-ADP-AG101
-=========
-
-ADP-AG101 is the SoC with AG101 hardcore CPU.
-
-Please check http://www.andestech.com/p2-4.htm for detail of this SoC.
-
-Configurations
-==============
-
-CONFIG_MEM_REMAP:
-	Doing memory remap is essential for preparing some non-OS or RTOS
-	applications.
-
-	This is also a must on ADP-AG101 board.
-	(While other boards may not have this problem).
-
-	The reason is because the ROM/FLASH circuit on PCB board.
-	AG101-A0 board has 2 jumpers MA17 and SW5 to configure which
-	ROM/FLASH is used to boot.
-
-	When SW5 = "0101", MA17 = LO, the ROM is connected to BANK0,
-	and the FLASH is connected to BANK1.
-	When SW5 = "1010", MA17 = HI, the ROM is disabled (still at BANK0),
-	and the FLASH is connected to BANK0.
-	It will occur problem when doing flash probing if the flash is at
-	BANK0 (0x00000000) while memory remapping was skipped.
-
-	Other board like ADP-AG101P may not enable this since there is only
-	a FLASH connected to bank0.
-
-CONFIG_SKIP_LOWLEVEL_INIT:
-	If you want to boot this system from FLASH and bypass e-bios (the
-	other boot loader on ROM). You should undefine CONFIG_SKIP_LOWLEVEL_INIT
-	in "include/configs/adp-ag101.h".
-
-Build and boot steps
-====================
-
-build:
-1. Prepare the toolchains and make sure the $PATH to toolchains is correct.
-2. Use `make adp-ag101` in u-boot root to build the image.
-
-burn u-boot to flash:
-1. Make sure the MA17 (J16) is Lo.
-2. Make sure the dip switch SW5 is set to "0101".
-3. Power On. Press button "S1", then press button "SW1", then you will found the
-   debug LED show 67 means the system successfully booted into e-bios.
-   Now you can control the e-bios boot loader from your console.
-4. Under "Command>>" prompt, enter "97" (CopyImageFromCard)
-5. Under "Type Dir Name of [CF/SD] =>" promtp, enter "c".
-6. Under "Enter Filename =>" prompt, enter the file name of u-boot image you
-   just build. It is usually "u-boot.bin".
-7. Under "Enter Dest. Address =>" prompt, enter the memory address where you
-   want to put the binary from SD card to RAM.
-   Address "0x500000" is our suggestion.
-8. Under "Command>>" prompt again, enter "55" (CLI) to use interactive command
-   environment.
-9. Under "CLI>" prompt, enter "burn 0x500000 0x80400000 0x30000" to burn the
-   binary from RAM to FLASH.
-10. Under "CLI>" prompt, enter "exit" to finish the burn process.
-
-boot u-boot from flash:
-1. Make sure the MA17 (J16) is Hi).
-2. Make sure the dip switch SW5 is set to "1010".
-3. Power On. Press button "S1", then you will see the debug LED count to 20.
-4. Now you can use u-boot on ADP-AG101 board.