* Code cleanup (ARM mostly)

* Patch by Curt Brune, 17 May 2004:
  - Add support for Samsung S3C4510B CPU (ARM7tdmi based SoC)
  - Add support for ESPD-Inc. EVB4510 Board

5 files changed, 229 insertions, 83 deletions

diff --git a/cpu/arm720t/cpu.c b/cpu/arm720t/cpu.c
index 0ad5481..58eab4e 100644
--- a/cpu/arm720t/cpu.c
+++ b/cpu/arm720t/cpu.c
@@ -33,51 +33,7 @@
 #include <common.h>
 #include <command.h>
 #include <clps7111.h>
-
-/* read co-processor 15, register #1 (control register) */
-static unsigned long read_p15_c1(void)
-{
-	unsigned long value;
-
-	__asm__ __volatile__(
-		"mrc     p15, 0, %0, c1, c0, 0   @ read control reg\n"
-		: "=r" (value)
-		:
-		: "memory");
-	/* printf("p15/c1 is = %08lx\n", value); */
-	return value;
-}
-
-/* write to co-processor 15, register #1 (control register) */
-static void write_p15_c1(unsigned long value)
-{
-	/* printf("write %08lx to p15/c1\n", value); */
-	__asm__ __volatile__(
-		"mcr     p15, 0, %0, c1, c0, 0   @ write it back\n"
-		:
-		: "r" (value)
-		: "memory");
-
-	read_p15_c1();
-}
-
-static void cp_delay (void)
-{
-	volatile int i;
-
-	/* copro seems to need some delay between reading and writing */
-	for (i = 0; i < 100; i++);
-}
-
-/* See also ARM Ref. Man. */
-#define C1_MMU		(1<<0)	/* mmu off/on */
-#define C1_ALIGN	(1<<1)	/* alignment faults off/on */
-#define C1_IDC		(1<<2)	/* icache and/or dcache off/on */
-#define C1_WRITE_BUFFER	(1<<3)	/* write buffer off/on */
-#define C1_BIG_ENDIAN	(1<<7)	/* big endian off/on */
-#define C1_SYS_PROT	(1<<8)	/* system protection */
-#define C1_ROM_PROT	(1<<9)	/* ROM protection */
-#define C1_HIGH_VECTORS	(1<<13)	/* location of vectors: low/high addresses */
+#include <asm/hardware.h>
 
 int cpu_init (void)
 {
@@ -103,12 +59,11 @@ int cleanup_before_linux (void)
 	 * and we set the CPU-speed to 73 MHz - see start.S for details
 	 */
 
+#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312)
 	unsigned long i;
 
 	disable_interrupts ();
-#ifdef CONFIG_NETARM
-	return 0;
-#endif
+
 	/* turn off I-cache */
 	asm ("mrc p15, 0, %0, c1, c0, 0":"=r" (i));
 	i &= ~0x1000;
@@ -116,11 +71,16 @@ int cleanup_before_linux (void)
 
 	/* flush I-cache */
 	asm ("mcr p15, 0, %0, c7, c5, 0": :"r" (i));
-
 #ifdef CONFIG_ARM7_REVD
 	/* go to high speed */
 	IO_SYSCON3 = (IO_SYSCON3 & ~CLKCTL) | CLKCTL_73;
 #endif
+#elif defined(CONFIG_NETARM) || defined(CONFIG_S3C4510B)
+	disable_interrupts ();
+	/* Nothing more needed */
+#else
+#error No cleanup_before_linux() defined for this CPU type
+#endif
 	return 0;
 }
 
@@ -134,6 +94,57 @@ int do_reset (cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
 	return (0);
 }
 
+/*
+ * Instruction and Data cache enable and disable functions
+ *
+ */
+
+#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312) || defined(CONFIG_NETARM)
+/* read co-processor 15, register #1 (control register) */
+static unsigned long read_p15_c1(void)
+{
+	unsigned long value;
+
+	__asm__ __volatile__(
+		"mrc     p15, 0, %0, c1, c0, 0   @ read control reg\n"
+		: "=r" (value)
+		:
+		: "memory");
+	/* printf("p15/c1 is = %08lx\n", value); */
+	return value;
+}
+
+/* write to co-processor 15, register #1 (control register) */
+static void write_p15_c1(unsigned long value)
+{
+	/* printf("write %08lx to p15/c1\n", value); */
+	__asm__ __volatile__(
+		"mcr     p15, 0, %0, c1, c0, 0   @ write it back\n"
+		:
+		: "r" (value)
+		: "memory");
+
+	read_p15_c1();
+}
+
+static void cp_delay (void)
+{
+	volatile int i;
+
+	/* copro seems to need some delay between reading and writing */
+	for (i = 0; i < 100; i++);
+}
+
+/* See also ARM Ref. Man. */
+#define C1_MMU		(1<<0)	/* mmu off/on */
+#define C1_ALIGN	(1<<1)	/* alignment faults off/on */
+#define C1_IDC		(1<<2)	/* icache and/or dcache off/on */
+#define C1_WRITE_BUFFER	(1<<3)	/* write buffer off/on */
+#define C1_BIG_ENDIAN	(1<<7)	/* big endian off/on */
+#define C1_SYS_PROT	(1<<8)	/* system protection */
+#define C1_ROM_PROT	(1<<9)	/* ROM protection */
+#define C1_HIGH_VECTORS	(1<<13)	/* location of vectors: low/high addresses */
+
 void icache_enable (void)
 {
 	ulong reg;
@@ -179,3 +190,65 @@ int dcache_status (void)
 {
 	return (read_p15_c1 () & C1_IDC) != 0;
 }
+
+#elif defined(CONFIG_S3C4510B)
+
+void icache_enable (void)
+{
+	s32 i;
+
+	/* disable all cache bits */
+	CLR_REG( REG_SYSCFG, 0x3F);
+
+	/* 8KB cache, write enable */
+	SET_REG( REG_SYSCFG, CACHE_WRITE_BUFF | CACHE_MODE_01);
+
+	/* clear TAG RAM bits */
+	for ( i = 0; i < 256; i++)
+	  PUT_REG( CACHE_TAG_RAM + 4*i, 0x00000000);
+
+	/* clear SET0 RAM */
+	for(i=0; i < 1024; i++)
+	  PUT_REG( CACHE_SET0_RAM + 4*i, 0x00000000);
+
+	/* clear SET1 RAM */
+	for(i=0; i < 1024; i++)
+	  PUT_REG( CACHE_SET1_RAM + 4*i, 0x00000000);
+
+	/* enable cache */
+	SET_REG( REG_SYSCFG, CACHE_ENABLE);
+
+}
+
+void icache_disable (void)
+{
+	/* disable all cache bits */
+	CLR_REG( REG_SYSCFG, 0x3F);
+}
+
+int icache_status (void)
+{
+	return GET_REG( REG_SYSCFG) & CACHE_ENABLE;
+}
+
+void dcache_enable (void)
+{
+	/* we don't have seperate instruction/data caches */
+	icache_enable();
+}
+
+void dcache_disable (void)
+{
+	/* we don't have seperate instruction/data caches */
+	icache_disable();
+}
+
+int dcache_status (void)
+{
+	/* we don't have seperate instruction/data caches */
+	return icache_status();
+}
+
+#else
+#error No icache/dcache enable/disable functions defined for this CPU type
+#endif
diff --git a/cpu/arm720t/interrupts.c b/cpu/arm720t/interrupts.c
index 67e581a..485443f 100644
--- a/cpu/arm720t/interrupts.c
+++ b/cpu/arm720t/interrupts.c
@@ -28,11 +28,8 @@
 
 #include <common.h>
 #include <clps7111.h>
-
 #include <asm/proc-armv/ptrace.h>
-#ifdef CONFIG_NETARM
-#include <asm/arch/netarm_registers.h>
-#endif
+#include <asm/hardware.h>
 
 extern void reset_cpu(ulong addr);
 
@@ -187,7 +184,8 @@ static ulong lastdec;
 
 int interrupt_init (void)
 {
-#ifdef CONFIG_NETARM
+
+#if defined(CONFIG_NETARM)
 	/* disable all interrupts */
 	IRQEN = 0;
 
@@ -198,7 +196,7 @@ int interrupt_init (void)
 
 	/* set timer 2 counter */
 	lastdec = TIMER_LOAD_VAL;
-#else
+#elif defined(CONFIG_IMPA7) || defined(CONFIG_EP7312)
 	/* disable all interrupts */
 	IO_INTMR1 = 0;
 
@@ -210,6 +208,11 @@ int interrupt_init (void)
 
 	/* set timer 1 counter */
 	lastdec = IO_TC1D = TIMER_LOAD_VAL;
+#elif defined(CONFIG_S3C4510B)
+	/* Nothing to do, interrupts not supported */
+	lastdec = 0;
+#else
+#error No interrupt_init() defined for this CPU type
 #endif
 	timestamp = 0;
 
@@ -220,6 +223,9 @@ int interrupt_init (void)
  * timer without interrupts
  */
 
+
+#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312) || defined(CONFIG_NETARM)
+
 void reset_timer (void)
 {
 	reset_timer_masked ();
@@ -285,3 +291,45 @@ void udelay_masked (unsigned long usec)
 	while (get_timer_masked () < tmo)
 		/*NOP*/;
 }
+
+#elif defined(CONFIG_S3C4510B)
+
+#define TMR_OFFSET (0x1000)
+
+void udelay (unsigned long usec)
+{
+	u32 rDATA;
+
+	rDATA = t_data_us(usec);
+
+	/* Stop timer 0 */
+	CLR_REG( REG_TMOD, TM0_RUN);
+
+	/* Configure for toggle mode */
+	SET_REG( REG_TMOD, TM0_TOGGLE);
+
+	/* Load Timer data register with count down value plus offset */
+	PUT_REG( REG_TDATA0, rDATA + TMR_OFFSET);
+
+	/* Clear timer counter register */
+	PUT_REG( REG_TCNT0, 0x0);
+
+	/* Start timer -- count down timer */
+	SET_REG( REG_TMOD, TM0_RUN);
+
+	/* spin during count down */
+	while ( GET_REG( REG_TCNT0) > TMR_OFFSET);
+
+	/* Stop timer */
+	CLR_REG( REG_TMOD, TM0_RUN);
+
+}
+
+ulong get_timer (ulong base)
+{
+	return (0xFFFFFFFF - GET_REG( REG_TCNT1)) - base;
+}
+
+#else
+#error Timer routines not defined for this CPU type
+#endif
diff --git a/cpu/arm720t/serial.c b/cpu/arm720t/serial.c
index 5c6a0cc..a5da4b7 100644
--- a/cpu/arm720t/serial.c
+++ b/cpu/arm720t/serial.c
@@ -1,5 +1,5 @@
 /*
- * (C) Copyright 2002
+ * (C) Copyright 2002-2004
  * Wolfgang Denk, DENX Software Engineering, <wd@denx.de>
  *
  * (C) Copyright 2002
@@ -29,9 +29,10 @@
  */
 
 #include <common.h>
-#include <clps7111.h>
 
-#ifndef CONFIG_NETARM
+#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312)
+
+#include <clps7111.h>
 
 void serial_setbrg (void)
 {
@@ -39,20 +40,15 @@ void serial_setbrg (void)
 
 	unsigned int reg = 0;
 
-	if (gd->baudrate == 1200)
-		reg = 191;
-	else if (gd->baudrate == 9600)
-		reg = 23;
-	else if (gd->baudrate == 19200)
-		reg = 11;
-	else if (gd->baudrate == 38400)
-		reg = 5;
-	else if (gd->baudrate == 57600)
-		reg = 3;
-	else if (gd->baudrate == 115200)
-		reg = 1;
-	else
-		hang ();
+	switch (gd->baudrate) {
+	case   1200:	reg = 191;	break;
+	case   9600:	reg =  23;	break;
+	case  19200:	reg =  11;	break;
+	case  38400:	reg =   5;	break;
+	case  57600:	reg =   3;	break;
+	case 115200:	reg =   1;	break;
+	default:	hang ();	break;
+	}
 
 	/* init serial serial 1,2 */
 	IO_SYSCON1 = SYSCON1_UART1EN;
@@ -127,4 +123,4 @@ serial_puts (const char *s)
 	}
 }
 
-#endif /* CONFIG_NETARM */
+#endif /* defined(CONFIG_IMPA7) || defined(CONFIG_EP7312) */
diff --git a/cpu/arm720t/serial_netarm.c b/cpu/arm720t/serial_netarm.c
index 8cfe049..56cdb0a 100644
--- a/cpu/arm720t/serial_netarm.c
+++ b/cpu/arm720t/serial_netarm.c
@@ -29,10 +29,11 @@
  */
 
 #include <common.h>
-#include <asm/arch/netarm_registers.h>
 
 #ifdef CONFIG_NETARM
 
+#include <asm/hardware.h>
+
 #define PORTA	(*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_PORTA))
 #define PORTB	(*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_PORTB))
 
diff --git a/cpu/arm720t/start.S b/cpu/arm720t/start.S
index f6ae9d6..15b9a05 100644
--- a/cpu/arm720t/start.S
+++ b/cpu/arm720t/start.S
@@ -26,9 +26,7 @@
 
 #include <config.h>
 #include <version.h>
-#ifdef CONFIG_NETARM
-#include <asm/arch/netarm_registers.h>
-#endif
+#include <asm/hardware.h>
 
 /*
  *************************************************************************
@@ -166,7 +164,6 @@ clbss_l:str	r2, [r0]		/* clear loop...                    */
 
 _start_armboot:	.word start_armboot
 
-
 /*
  *************************************************************************
  *
@@ -178,6 +175,7 @@ _start_armboot:	.word start_armboot
  *************************************************************************
  */
 
+#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312)
 
 /* Interupt-Controller base addresses */
 INTMR1:		.word	0x80000280 @ 32 bit size
@@ -195,8 +193,11 @@ SYSCON3:	.word	0x80002200
 #define CLKCTL_49      0x4  /* 49.152 MHz */
 #define CLKCTL_73      0x6  /* 73.728 MHz */
 
+#endif
+
 cpu_init_crit:
-#ifndef CONFIG_NETARM
+#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312)
+
 	/*
 	 * mask all IRQs by clearing all bits in the INTMRs
 	 */
@@ -223,7 +224,7 @@ cpu_init_crit:
 	bic	r0, r0, #0x0000008f	@ clear bits 7, 3:0 (B--- WCAM)
 	orr	r0, r0, #0x00000002	@ set bit 2 (A) Align
 	mcr	p15,0,r0,c1,c0
-#else /* CONFIG_NETARM */
+#elif defined(CONFIG_NETARM)
 	/*
 	 * prior to software reset : need to set pin PORTC4 to be *HRESET
 	 */
@@ -270,7 +271,26 @@ cpu_init_crit:
 	mov	r1, #0
 	ldr	r0, =NETARM_GEN_MODULE_BASE
 	str	r1, [r0, #+NETARM_GEN_INTR_ENABLE]
-#endif /* CONFIG_NETARM */
+
+#elif defined(CONFIG_S3C4510B)
+
+	/*
+	 * Mask off all IRQ sources
+	 */
+	ldr	r1, =REG_INTMASK
+	ldr	r0, =0x3FFFFF
+	str	r0, [r1]
+
+	/*
+	 * Disable Cache
+	 */
+	ldr r0, =REG_SYSCFG
+	ldr r1, =0x83ffffa0     /* cache-disabled  */
+	str r1, [r0]
+
+#else
+#error No cpu_init_crit() defined for current CPU type
+#endif
 
 #ifdef CONFIG_ARM7_REVD
 	/* set clock speed */
@@ -462,10 +482,10 @@ fiq:
 
 #endif
 
+#if defined(CONFIG_IMPA7) || defined(CONFIG_EP7312)
 	.align	5
 .globl reset_cpu
 reset_cpu:
-#ifndef CONFIG_NETARM
 	mov     ip, #0
 	mcr     p15, 0, ip, c7, c7, 0           @ invalidate cache
 	mcr     p15, 0, ip, c8, c7, 0           @ flush TLB (v4)
@@ -474,7 +494,10 @@ reset_cpu:
 	bic     ip, ip, #0x2100                 @ ..v....s........
 	mcr     p15, 0, ip, c1, c0, 0           @ ctrl register
 	mov     pc, r0
-#else
+#elif defined(CONFIG_NETARM)
+	.align	5
+.globl reset_cpu
+reset_cpu:
 	ldr	r1, =NETARM_MEM_MODULE_BASE
 	ldr	r0, [r1, #+NETARM_MEM_CS0_BASE_ADDR]
 	ldr	r1, =0xFFFFF000
@@ -491,4 +514,9 @@ reset_cpu:
 	ldr	r1, =NETARM_GEN_SW_SVC_RESETB
 	str	r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
 	mov	pc, r0
+#elif defined(CONFIG_S3C4510B)
+/* Nothing done here as reseting the CPU is board specific, depending
+ * on external peripherals such as watchdog timers, etc. */
+#else
+#error No reset_cpu() defined for current CPU type
 #endif