summaryrefslogtreecommitdiff
path: root/configs
diff options
context:
space:
mode:
authorStephen Warren <swarren@wwwdotorg.org>2016-04-01 21:14:15 -0600
committerTom Rini <trini@konsulko.com>2016-04-11 12:44:38 -0400
commitd22a765755ba318ce162a976f51d44000a201394 (patch)
treed259579e9edc7c8ff8f90c73dc44658c3c8a41d6 /configs
parent7439b4399b14242e6c41b86734baa3fe31c4517f (diff)
downloadu-boot-imx-d22a765755ba318ce162a976f51d44000a201394.zip
u-boot-imx-d22a765755ba318ce162a976f51d44000a201394.tar.gz
u-boot-imx-d22a765755ba318ce162a976f51d44000a201394.tar.bz2
ARM: add Raspberry Pi 3 64-bit config
On all Pis so far, the VC FW provides a short stub to set up the ARM CPU before entering the kernel (a/k/a U-Boot for us). This feature is not currently supported by the VC FW when booting in 64-bit mode. However, this feature will likely appear in the near future, and this U-Boot port assumes that such a feature is in place. Without that feature, or a temporary workaround described below, U-Boot will not boot. Once the VC FW does provide the ARM stub, u-boot.bin built for rpi_3 can be used drectly as kernel7.img, in the same way as any other RPi port. The following config.txt is required: # Fix mini UART input frequency, and setup/enable up the UART. # Without this option, U-Boot will not boot, even if you don't care # about the serial console. This option will always be required for # all RPi3 use-cases, unless the PL011 UART is used, which is not # yet supported by rpi_3* builds of U-Boot. enable_uart=1 # Boot in AArch64 (64-bit) mode. # It is possible that a future VC FW will remove the need for this # option, instead auto-setting 32-/64-bit mode based on the "kernel" # filename present on the SD card. arm_control=0x200 Prior to the VC FW providing the ARM boot stub, you can use the following steps to build an equivalent stub into the U-Boot binary: git clone https://github.com/swarren/rpi-3-aarch64-demo.git \ ../rpi-3-aarch64-demo (cd ../rpi-3-aarch64-demo && ./build.sh) Build U-Boot for rpi_3 in the usual way cat ../rpi-3-aarch64-demo/armstub64.bin u-boot.bin > u-boot.bin.stubbed Use u-boot.bin.stubbed as kernel7.img on the Pi SD card. In this case, the following additional entries are required in config.txt: # Tell the FW to load the kernel image at address 0, the reset vector. kernel_old=1 Signed-off-by: Stephen Warren <swarren@wwwdotorg.org> Reviewed-by: Tom Rini <trini@konsulko.com>
Diffstat (limited to 'configs')
-rw-r--r--configs/rpi_3_defconfig11
1 files changed, 11 insertions, 0 deletions
diff --git a/configs/rpi_3_defconfig b/configs/rpi_3_defconfig
new file mode 100644
index 0000000..417836b
--- /dev/null
+++ b/configs/rpi_3_defconfig
@@ -0,0 +1,11 @@
+CONFIG_ARM=y
+CONFIG_ARCH_BCM283X=y
+CONFIG_TARGET_RPI_3=y
+CONFIG_OF_BOARD_SETUP=y
+CONFIG_SYS_PROMPT="U-Boot> "
+# CONFIG_CMD_IMLS is not set
+# CONFIG_CMD_FLASH is not set
+# CONFIG_CMD_FPGA is not set
+CONFIG_CMD_GPIO=y
+CONFIG_PHYS_TO_BUS=y
+CONFIG_OF_LIBFDT=y