exynos: video: Drop old unused code

Now that we are using driver model, we can drop the weak functions and LCD
init in the board file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>

1 files changed, 0 insertions, 153 deletions

diff --git a/board/samsung/common/exynos5-dt.c b/board/samsung/common/exynos5-dt.c
index 0dcea71..2e3b16d 100644
--- a/board/samsung/common/exynos5-dt.c
+++ b/board/samsung/common/exynos5-dt.c
@@ -147,159 +147,6 @@ int board_get_revision(void)
 	return 0;
 }
 
-#ifdef CONFIG_LCD
-
-static int board_dp_bridge_init(struct udevice *dev)
-{
-	const int max_tries = 10;
-	int num_tries;
-	int ret;
-
-	debug("%s\n", __func__);
-	ret = video_bridge_attach(dev);
-	if (ret) {
-		debug("video bridge init failed: %d\n", ret);
-		return ret;
-	}
-
-	/*
-	 * We need to wait for 90ms after bringing up the bridge since there
-	 * is a phantom "high" on the HPD chip during its bootup.  The phantom
-	 * high comes within 7ms of de-asserting PD and persists for at least
-	 * 15ms.  The real high comes roughly 50ms after PD is de-asserted. The
-	 * phantom high makes it hard for us to know when the NXP chip is up.
-	 */
-	mdelay(90);
-
-	for (num_tries = 0; num_tries < max_tries; num_tries++) {
-		/* Check HPD. If it's high, or we don't have it, all is well */
-		ret = video_bridge_check_attached(dev);
-		if (!ret || ret == -ENOENT)
-			return 0;
-
-		debug("%s: eDP bridge failed to come up; try %d of %d\n",
-		      __func__, num_tries, max_tries);
-	}
-
-	/* Immediately go into bridge reset if the hp line is not high */
-	return -EIO;
-}
-
-static int board_dp_bridge_setup(const void *blob)
-{
-	const int max_tries = 2;
-	int num_tries;
-	struct udevice *dev;
-	int ret;
-
-	/* Configure I2C registers for Parade bridge */
-	ret = uclass_get_device(UCLASS_VIDEO_BRIDGE, 0, &dev);
-	if (ret) {
-		debug("video bridge init failed: %d\n", ret);
-		return ret;
-	}
-
-	if (strncmp(dev->driver->name, "parade", 6)) {
-		/* Mux HPHPD to the special hotplug detect mode */
-		exynos_pinmux_config(PERIPH_ID_DPHPD, 0);
-	}
-
-	for (num_tries = 0; num_tries < max_tries; num_tries++) {
-		ret = board_dp_bridge_init(dev);
-		if (!ret)
-			return 0;
-		if (num_tries == max_tries - 1)
-			break;
-
-		/*
-		* If we're here, the bridge chip failed to initialise.
-		* Power down the bridge in an attempt to reset.
-		*/
-		video_bridge_set_active(dev, false);
-
-		/*
-		* Arbitrarily wait 300ms here with DP_N low.  Don't know for
-		* sure how long we should wait, but we're being paranoid.
-		*/
-		mdelay(300);
-	}
-
-	return ret;
-}
-
-void exynos_cfg_lcd_gpio(void)
-{
-	/* For Backlight */
-	gpio_request(EXYNOS5_GPIO_B20, "lcd_backlight");
-	gpio_cfg_pin(EXYNOS5_GPIO_B20, S5P_GPIO_OUTPUT);
-	gpio_set_value(EXYNOS5_GPIO_B20, 1);
-}
-
-static int board_dp_set_backlight(int percent)
-{
-	struct udevice *dev;
-	int ret;
-
-	ret = uclass_get_device(UCLASS_VIDEO_BRIDGE, 0, &dev);
-	if (!ret)
-		ret = video_bridge_set_backlight(dev, percent);
-
-	return ret;
-}
-
-void exynos_backlight_on(unsigned int on)
-{
-	struct udevice *dev;
-	int ret;
-
-	debug("%s(%u)\n", __func__, on);
-	if (!on)
-		return;
-
-	ret = regulator_get_by_platname("vcd_led", &dev);
-	if (!ret)
-		ret = regulator_set_enable(dev, true);
-	if (ret)
-		debug("Failed to enable backlight: ret=%d\n", ret);
-
-	/* T5 in the LCD timing spec (defined as > 10ms) */
-	mdelay(10);
-
-	/* board_dp_backlight_pwm */
-	gpio_direction_output(EXYNOS5_GPIO_B20, 1);
-
-	/* T6 in the LCD timing spec (defined as > 10ms) */
-	mdelay(10);
-
-	/* try to set the backlight in the bridge registers */
-	ret = board_dp_set_backlight(80);
-
-	/* if we have no bridge or it does not support backlight, use a GPIO */
-	if (ret == -ENODEV || ret == -ENOSYS) {
-		gpio_request(EXYNOS5_GPIO_X30, "board_dp_backlight_en");
-		gpio_direction_output(EXYNOS5_GPIO_X30, 1);
-	}
-}
-
-void exynos_lcd_power_on(void)
-{
-	struct udevice *dev;
-	int ret;
-
-	debug("%s\n", __func__);
-	ret = regulator_get_by_platname("lcd_vdd", &dev);
-	if (!ret)
-		ret = regulator_set_enable(dev, true);
-	if (ret)
-		debug("Failed to enable LCD panel: ret=%d\n", ret);
-
-	ret = board_dp_bridge_setup(gd->fdt_blob);
-	if (ret && ret != -ENODEV)
-		printf("LCD bridge failed to enable: %d\n", ret);
-}
-
-#endif
-
 #ifdef CONFIG_USB_DWC3
 static struct dwc3_device dwc3_device_data = {
 	.maximum_speed = USB_SPEED_SUPER,