arm: Remove openrd boards

These boards have not been converted to generic board by the deadline.
Remove them.

Signed-off-by: Simon Glass <sjg@chromium.org>

6 files changed, 0 insertions, 381 deletions

diff --git a/board/Marvell/openrd/Kconfig b/board/Marvell/openrd/Kconfig
deleted file mode 100644
index 124b66d..0000000
--- a/board/Marvell/openrd/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_OPENRD
-
-config SYS_BOARD
-	default "openrd"
-
-config SYS_VENDOR
-	default "Marvell"
-
-config SYS_CONFIG_NAME
-	default "openrd"
-
-endif
diff --git a/board/Marvell/openrd/MAINTAINERS b/board/Marvell/openrd/MAINTAINERS
deleted file mode 100644
index 7a189ab..0000000
--- a/board/Marvell/openrd/MAINTAINERS
+++ /dev/null
@@ -1,12 +0,0 @@
-OPENRD BOARD
-M:	Prafulla Wadaskar <prafulla@marvell.com>
-S:	Maintained
-F:	board/Marvell/openrd/
-F:	include/configs/openrd.h
-F:	configs/openrd_base_defconfig
-
-OPENRD_CLIENT BOARD
-#M:	-
-S:	Maintained
-F:	configs/openrd_client_defconfig
-F:	configs/openrd_ultimate_defconfig
diff --git a/board/Marvell/openrd/Makefile b/board/Marvell/openrd/Makefile
deleted file mode 100644
index 8f95b79..0000000
--- a/board/Marvell/openrd/Makefile
+++ /dev/null
@@ -1,14 +0,0 @@
-#
-# (C) Copyright 2009
-# Net Insight <www.netinsight.net>
-# Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
-#
-# Based on sheevaplug:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= openrd.o
diff --git a/board/Marvell/openrd/kwbimage.cfg b/board/Marvell/openrd/kwbimage.cfg
deleted file mode 100644
index 8e59937..0000000
--- a/board/Marvell/openrd/kwbimage.cfg
+++ /dev/null
@@ -1,152 +0,0 @@
-#
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM	nand
-NAND_ECC_MODE	default
-NAND_PAGE_SIZE	0x0800
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1b1b1b9b
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000c30	# DDR Configuration register
-# bit13-0:  0xc30 (3120 DDR2 clks refresh rate)
-# bit23-14: zero
-# bit24: 1= enable exit self refresh mode on DDR access
-# bit25: 1 required
-# bit29-26: zero
-# bit31-30: 01
-
-DATA 0xFFD01404 0x37543000	# DDR Controller Control Low
-# bit 4:    0=addr/cmd in smame cycle
-# bit 5:    0=clk is driven during self refresh, we don't care for APX
-# bit 6:    0=use recommended falling edge of clk for addr/cmd
-# bit14:    0=input buffer always powered up
-# bit18:    1=cpu lock transaction enabled
-# bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0
-# bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM
-# bit30-28: 3 required
-# bit31:    0=no additional STARTBURST delay
-
-DATA 0xFFD01408 0x22125451	# DDR Timing (Low) (active cycles value +1)
-# bit3-0:   TRAS lsbs
-# bit7-4:   TRCD
-# bit11- 8: TRP
-# bit15-12: TWR
-# bit19-16: TWTR
-# bit20:    TRAS msb
-# bit23-21: 0x0
-# bit27-24: TRRD
-# bit31-28: TRTP
-
-DATA 0xFFD0140C 0x00000a33	#  DDR Timing (High)
-# bit6-0:   TRFC
-# bit8-7:   TR2R
-# bit10-9:  TR2W
-# bit12-11: TW2W
-# bit31-13: zero required
-
-DATA 0xFFD01410 0x000000cc	#  DDR Address Control
-# bit1-0:   00, Cs0width=x8
-# bit3-2:   11, Cs0size=1Gb
-# bit5-4:   00, Cs1width=x8
-# bit7-6:   11, Cs1size=1Gb
-# bit9-8:   00, Cs2width=nonexistent
-# bit11-10: 00, Cs2size =nonexistent
-# bit13-12: 00, Cs3width=nonexistent
-# bit15-14: 00, Cs3size =nonexistent
-# bit16:    0,  Cs0AddrSel
-# bit17:    0,  Cs1AddrSel
-# bit18:    0,  Cs2AddrSel
-# bit19:    0,  Cs3AddrSel
-# bit31-20: 0 required
-
-DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
-# bit0:    0,  OpenPage enabled
-# bit31-1: 0 required
-
-DATA 0xFFD01418 0x00000000	#  DDR Operation
-# bit3-0:   0x0, DDR cmd
-# bit31-4:  0 required
-
-DATA 0xFFD0141C 0x00000C52	#  DDR Mode
-# bit2-0:   2, BurstLen=2 required
-# bit3:     0, BurstType=0 required
-# bit6-4:   4, CL=5
-# bit7:     0, TestMode=0 normal
-# bit8:     0, DLL reset=0 normal
-# bit11-9:  6, auto-precharge write recovery ????????????
-# bit12:    0, PD must be zero
-# bit31-13: 0 required
-
-DATA 0xFFD01420 0x00000042	#  DDR Extended Mode
-# bit0:    0,  DDR DLL enabled
-# bit1:    1,  DDR drive strength reduced
-# bit2:    0,  DDR ODT control lsd (disabled)
-# bit5-3:  000, required
-# bit6:    1,  DDR ODT control msb, (disabled)
-# bit9-7:  000, required
-# bit10:   0,  differential DQS enabled
-# bit11:   0, required
-# bit12:   0, DDR output buffer enabled
-# bit31-13: 0 required
-
-DATA 0xFFD01424 0x0000F17F	#  DDR Controller Control High
-# bit2-0:  111, required
-# bit3  :  1  , MBUS Burst Chop disabled
-# bit6-4:  111, required
-# bit7  :  0
-# bit8  :  1  , add writepath sample stage, must be 1 for DDR freq >= 300MHz
-# bit9  :  0  , no half clock cycle addition to dataout
-# bit10 :  0  , 1/4 clock cycle skew enabled for addr/ctl signals
-# bit11 :  0  , 1/4 clock cycle skew disabled for write mesh
-# bit15-12: 1111 required
-# bit31-16: 0    required
-
-DATA 0xFFD01428 0x00085520	# DDR2 ODT Read Timing (default values)
-DATA 0xFFD0147C 0x00008552	# DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01500 0x00000000	# CS[0]n Base address to 0x0
-DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
-# bit0:    1,  Window enabled
-# bit1:    0,  Write Protect disabled
-# bit3-2:  00, CS0 hit selected
-# bit23-4: ones, required
-# bit31-24: 0x0F, Size (i.e. 256MB)
-
-DATA 0xFFD01508 0x10000000	# CS[1]n Base address to 256Mb
-DATA 0xFFD0150C 0x0FFFFFF5	# CS[1]n Size 256Mb Window enabled for CS1
-
-DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
-
-DATA 0xFFD01494 0x00120012	#  DDR ODT Control (Low)
-# bit3-0:   0010, (read) M_ODT[0] is asserted during read from DRAM CS1
-# bit7-4:   0001, (read) M_ODT[1] is asserted during read from DRAM CS0
-# bit19-16: 0010, (write) M_ODT[0] is asserted during write to DRAM CS1.
-# bit23-20: 0001, (write) M_ODT[1] is asserted during write to DRAM CS0.
-DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
-
-DATA 0xFFD0149C 0x0000E40f	# CPU ODT Control
-# bit3-0:    1111, internal ODT is asserted during read from DRAM bank 0-3
-# bit11-10:    01, M_DQ, M_DM, and M_DQS I/O buffer ODT Select: 150 ohm
-# bit13-12:    10, M_STARTBURST_IN I/O buffer ODT Select: 75 ohm
-# bit14:        1, M_STARTBURST_IN ODT: Enabled
-# bit15:        1, DDR IO ODT Unit: Use ODT block
-DATA 0xFFD01480 0x00000001	# DDR Initialization Control
-#bit0=1, enable DDR init upon this register write
-
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/Marvell/openrd/openrd.c b/board/Marvell/openrd/openrd.c
deleted file mode 100644
index 55cf525..0000000
--- a/board/Marvell/openrd/openrd.c
+++ /dev/null
@@ -1,161 +0,0 @@
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
- *
- * Based on sheevaplug.c:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <miiphy.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include "openrd.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/*
-	 * default gpio configuration
-	 * There are maximum 64 gpios controlled through 2 sets of registers
-	 * the  below configuration configures mainly initial LED status
-	 */
-	mvebu_config_gpio(OPENRD_OE_VAL_LOW,
-			  OPENRD_OE_VAL_HIGH,
-			  OPENRD_OE_LOW, OPENRD_OE_HIGH);
-
-	/* Multi-Purpose Pins Functionality configuration */
-	static const u32 kwmpp_config[] = {
-		MPP0_NF_IO2,
-		MPP1_NF_IO3,
-		MPP2_NF_IO4,
-		MPP3_NF_IO5,
-		MPP4_NF_IO6,
-		MPP5_NF_IO7,
-		MPP6_SYSRST_OUTn,
-		MPP7_GPO,
-		MPP8_TW_SDA,
-		MPP9_TW_SCK,
-		MPP10_UART0_TXD,
-		MPP11_UART0_RXD,
-		MPP12_SD_CLK,
-		MPP13_SD_CMD, /* Alt UART1_TXD */
-		MPP14_SD_D0,  /* Alt UART1_RXD */
-		MPP15_SD_D1,
-		MPP16_SD_D2,
-		MPP17_SD_D3,
-		MPP18_NF_IO0,
-		MPP19_NF_IO1,
-		MPP20_GE1_0,
-		MPP21_GE1_1,
-		MPP22_GE1_2,
-		MPP23_GE1_3,
-		MPP24_GE1_4,
-		MPP25_GE1_5,
-		MPP26_GE1_6,
-		MPP27_GE1_7,
-		MPP28_GPIO,
-		MPP29_TSMP9,
-		MPP30_GE1_10,
-		MPP31_GE1_11,
-		MPP32_GE1_12,
-		MPP33_GE1_13,
-		MPP34_GPIO,   /* UART1 / SD sel */
-		MPP35_TDM_CH0_TX_QL,
-		MPP36_TDM_SPI_CS1,
-		MPP37_TDM_CH2_TX_QL,
-		MPP38_TDM_CH2_RX_QL,
-		MPP39_AUDIO_I2SBCLK,
-		MPP40_AUDIO_I2SDO,
-		MPP41_AUDIO_I2SLRC,
-		MPP42_AUDIO_I2SMCLK,
-		MPP43_AUDIO_I2SDI,
-		MPP44_AUDIO_EXTCLK,
-		MPP45_TDM_PCLK,
-		MPP46_TDM_FS,
-		MPP47_TDM_DRX,
-		MPP48_TDM_DTX,
-		MPP49_TDM_CH0_RX_QL,
-		0
-	};
-
-	kirkwood_mpp_conf(kwmpp_config, NULL);
-	return 0;
-}
-
-int board_init(void)
-{
-	/*
-	 * arch number of board
-	 */
-#if defined(CONFIG_BOARD_IS_OPENRD_BASE)
-	gd->bd->bi_arch_number = MACH_TYPE_OPENRD_BASE;
-#elif defined(CONFIG_BOARD_IS_OPENRD_CLIENT)
-	gd->bd->bi_arch_number = MACH_TYPE_OPENRD_CLIENT;
-#elif defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
-	gd->bd->bi_arch_number = MACH_TYPE_OPENRD_ULTIMATE;
-#endif
-
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-	return 0;
-}
-
-#ifdef CONFIG_RESET_PHY_R
-/* Configure and enable MV88E1116/88E1121 PHY */
-void mv_phy_init(char *name)
-{
-	u16 reg;
-	u16 devadr;
-
-	if (miiphy_set_current_dev(name))
-		return;
-
-	/* command to read PHY dev address */
-	if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
-		printf("Err..%s could not read PHY dev address\n",
-			__FUNCTION__);
-		return;
-	}
-
-	/*
-	 * Enable RGMII delay on Tx and Rx for CPU port
-	 * Ref: sec 4.7.2 of chip datasheet
-	 */
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
-	miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, &reg);
-	reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
-	miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
-	miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
-
-	/* reset the phy */
-	miiphy_reset(name, devadr);
-
-	printf(PHY_NO" Initialized on %s\n", name);
-}
-
-void reset_phy(void)
-{
-	mv_phy_init("egiga0");
-
-#ifdef CONFIG_BOARD_IS_OPENRD_CLIENT
-	/* Kirkwood ethernet driver is written with the assumption that in case
-	 * of multiple PHYs, their addresses are consecutive. But unfortunately
-	 * in case of OpenRD-Client, PHY addresses are not consecutive.*/
-	miiphy_write("egiga1", 0xEE, 0xEE, 24);
-#endif
-
-#if defined(CONFIG_BOARD_IS_OPENRD_CLIENT) || \
-	defined(CONFIG_BOARD_IS_OPENRD_ULTIMATE)
-	/* configure and initialize both PHY's */
-	mv_phy_init("egiga1");
-#endif
-}
-#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/openrd/openrd.h b/board/Marvell/openrd/openrd.h
deleted file mode 100644
index 56dfeea..0000000
--- a/board/Marvell/openrd/openrd.h
+++ /dev/null
@@ -1,30 +0,0 @@
-/*
- * (C) Copyright 2009
- * Net Insight <www.netinsight.net>
- * Written-by: Simon Kagstrom <simon.kagstrom@netinsight.net>
- *
- * Based on sheevaplug.h:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef __OPENRD_BASE_H
-#define __OPENRD_BASE_H
-
-#define OPENRD_OE_LOW		(~(1<<28))        /* RS232 / RS485 */
-#define OPENRD_OE_HIGH		(~(1<<2))         /* SD / UART1 */
-#define OPENRD_OE_VAL_LOW		(0)       /* Sel RS232 */
-#define OPENRD_OE_VAL_HIGH		(1 << 2)  /* Sel SD */
-
-/* PHY related */
-#define MV88E1116_LED_FCTRL_REG		10
-#define MV88E1116_CPRSP_CR3_REG		21
-#define MV88E1116_MAC_CTRL_REG		21
-#define MV88E1116_PGADR_REG		22
-#define MV88E1116_RGMII_TXTM_CTRL	(1 << 4)
-#define MV88E1116_RGMII_RXTM_CTRL	(1 << 5)
-
-#endif /* __OPENRD_BASE_H */