ARM: IXP: Remove actux1 board

The board is unmaintained, just like the rest of the IXP.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>

4 files changed, 0 insertions, 296 deletions

diff --git a/board/actux1/Makefile b/board/actux1/Makefile
deleted file mode 100644
index 05a8669..0000000
--- a/board/actux1/Makefile
+++ /dev/null
@@ -1,8 +0,0 @@
-#
-# (C) Copyright 2000-2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= actux1.o
diff --git a/board/actux1/actux1.c b/board/actux1/actux1.c
deleted file mode 100644
index 03ccd93..0000000
--- a/board/actux1/actux1.c
+++ /dev/null
@@ -1,148 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * (C) Copyright 2006
- * Stefan Roese, DENX Software Engineering, sr@denx.de.
- *
- * (C) Copyright 2002
- * Kyle Harris, Nexus Technologies, Inc. kharris@nexus-tech.net
- *
- * (C) Copyright 2002
- * Sysgo Real-Time Solutions, GmbH <www.elinos.com>
- * Marius Groeger <mgroeger@sysgo.de>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <malloc.h>
-#include <asm/arch/ixp425.h>
-#include <asm/io.h>
-#include <miiphy.h>
-#ifdef CONFIG_PCI
-#include <pci.h>
-#include <asm/arch/ixp425pci.h>
-#endif
-
-#include "actux1_hw.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-int board_early_init_f(void)
-{
-	/* CS5: Debug port */
-	writel(0x9d520003, IXP425_EXP_CS5);
-	/* CS6: HwRel */
-	writel(0x81860001, IXP425_EXP_CS6);
-	/* CS7: LEDs */
-	writel(0x80900003, IXP425_EXP_CS7);
-	return 0;
-}
-
-int board_init(void)
-{
-	/* adress of boot parameters */
-	gd->bd->bi_boot_params = 0x00000100;
-
-	GPIO_OUTPUT_CLEAR(CONFIG_SYS_GPIO_IORST);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_IORST);
-
-	/* Setup GPIOs for PCI INTA */
-	GPIO_OUTPUT_DISABLE(CONFIG_SYS_GPIO_PCI1_INTA);
-	GPIO_INT_ACT_LOW_SET(CONFIG_SYS_GPIO_PCI1_INTA);
-
-	/* Setup GPIOs for 33MHz clock output */
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_PCI_CLK);
-	GPIO_OUTPUT_ENABLE(CONFIG_SYS_GPIO_EXTBUS_CLK);
-	writel(0x011001FF, IXP425_GPIO_GPCLKR);
-
-	udelay(533);
-	GPIO_OUTPUT_SET(CONFIG_SYS_GPIO_IORST);
-
-	ACTUX1_LED1(2);
-	ACTUX1_LED2(2);
-	ACTUX1_LED3(0);
-	ACTUX1_LED4(0);
-	ACTUX1_LED5(0);
-	ACTUX1_LED6(0);
-	ACTUX1_LED7(0);
-
-	ACTUX1_HS(ACTUX1_HS_DCD);
-
-	return 0;
-}
-
-/*
- * Check Board Identity
- */
-int checkboard(void)
-{
-	char buf[64];
-	int i = getenv_f("serial#", buf, sizeof(buf));
-
-	puts("Board: AcTux-1 rev.");
-	putc(ACTUX1_BOARDREL + 'A' - 1);
-
-	if (i > 0) {
-		puts(", serial# ");
-		puts(buf);
-	}
-	putc('\n');
-
-	return 0;
-}
-
-/*************************************************************************
- * get_board_rev() - setup to pass kernel board revision information
- * 0 = reserved
- * 1 = Rev. A
- * 2 = Rev. B
- *************************************************************************/
-u32 get_board_rev(void)
-{
-	return ACTUX1_BOARDREL;
-}
-
-int dram_init(void)
-{
-	gd->ram_size = get_ram_size(CONFIG_SYS_SDRAM_BASE, 128<<20);
-	return 0;
-}
-
-
-#ifdef CONFIG_PCI
-struct pci_controller hose;
-
-void pci_init_board(void)
-{
-	pci_ixp_init(&hose);
-}
-#endif
-
-void reset_phy(void)
-{
-	u16 id1, id2;
-
-	/* initialize the PHY */
-	miiphy_reset("NPE0", CONFIG_PHY_ADDR);
-
-	miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID1, &id1);
-	miiphy_read("NPE0", CONFIG_PHY_ADDR, MII_PHYSID2, &id2);
-
-	id2 &= 0xFFF0;		/* mask out revision bits */
-
-	if (id1 == 0x13 && id2 == 0x78e0) {
-		/*
-		 * LXT971/LXT972 PHY: set LED outputs:
-		 * LED1(green) = Link/ACT,
-		 * LED2 (unused) = LINK,
-		 * LED3(red) = Coll
-		 */
-		miiphy_write("NPE0", CONFIG_PHY_ADDR, 20, 0xD432);
-	} else if (id1 == 0x143 && id2 == 0xbc30) {
-		/* BCM5241: default values are OK */
-	} else
-		printf("unknown ethernet PHY ID: %x %x\n", id1, id2);
-}
diff --git a/board/actux1/actux1_hw.h b/board/actux1/actux1_hw.h
deleted file mode 100644
index 5627f24..0000000
--- a/board/actux1/actux1_hw.h
+++ /dev/null
@@ -1,41 +0,0 @@
-/*
- * (C) Copyright 2007
- * Michael Schwingen, michael@schwingen.org
- *
- * hardware register definitions for the AcTux-1 board.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _ACTUX1_HW_H
-#define _ACTUX1_HW_H
-
-/* 0 = LED off,1 = green, 2 = red, 3 = orange */
-#define ACTUX1_LED1(a)	writeb((a),   IXP425_EXP_BUS_CS7_BASE_PHYS + 0)
-#define ACTUX1_LED2(a)	writeb((a),   IXP425_EXP_BUS_CS7_BASE_PHYS + 1)
-#define ACTUX1_LED3(a)	writeb((a),   IXP425_EXP_BUS_CS7_BASE_PHYS + 2)
-#define ACTUX1_LED4(a)	writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 3)
-#define ACTUX1_LED5(a)	writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 4)
-#define ACTUX1_LED6(a)	writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 5)
-#define ACTUX1_LED7(a)	writeb((a)^3, IXP425_EXP_BUS_CS7_BASE_PHYS + 6)
-#define ACTUX1_HS(a)	writeb((a),   IXP425_EXP_BUS_CS7_BASE_PHYS + 7)
-#define ACTUX1_HS_DCD	0x01
-#define ACTUX1_HS_DSR	0x02
-
-#define ACTUX1_DBG_PORT	IXP425_EXP_BUS_CS5_BASE_PHYS
-#define ACTUX1_BOARDREL	(readb(IXP425_EXP_BUS_CS6_BASE_PHYS) & 0x0F)
-
-/* GPIO settings */
-#define CONFIG_SYS_GPIO_PCI1_INTA		2
-#define CONFIG_SYS_GPIO_PCI2_INTA		3
-#define CONFIG_SYS_GPIO_I2C_SDA		4
-#define CONFIG_SYS_GPIO_I2C_SCL		5
-#define CONFIG_SYS_GPIO_DBGJUMPER		9
-#define CONFIG_SYS_GPIO_BUTTON1		10
-#define CONFIG_SYS_GPIO_DBGSENSE		11
-#define CONFIG_SYS_GPIO_DTR			12
-#define CONFIG_SYS_GPIO_IORST			13	/* Out */
-#define CONFIG_SYS_GPIO_PCI_CLK		14	/* Out */
-#define CONFIG_SYS_GPIO_EXTBUS_CLK		15	/* Out */
-
-#endif
diff --git a/board/actux1/u-boot.lds b/board/actux1/u-boot.lds
deleted file mode 100644
index 4716e4f..0000000
--- a/board/actux1/u-boot.lds
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * (C) Copyright 2000
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-OUTPUT_FORMAT ("elf32-bigarm", "elf32-bigarm", "elf32-bigarm")
-OUTPUT_ARCH (arm)
-ENTRY (_start)
-SECTIONS
-{
-	. = 0x00000000;
-
-	. = ALIGN (4);
-	.text : {
-		*(.__image_copy_start)
-		arch/arm/cpu/ixp/start.o(.text*)
-		net/built-in.o(.text*)
-		board/actux1/built-in.o(.text*)
-		arch/arm/cpu/ixp/built-in.o(.text*)
-		drivers/input/built-in.o(.text*)
-
-		. = env_offset;
-		common/env_embedded.o(.ppcenv)
-		*(.text*)
-	}
-
-	. = ALIGN(4);
-	.rodata : {
-		*(SORT_BY_ALIGNMENT(SORT_BY_NAME(.rodata*)))
-	}
-	. = ALIGN(4);
-	.data : {
-		*(.data*)
-	}
-	. = ALIGN(4);
-	.got : {
-		*(.got)
-	}
-	. =.;
-
-	. = ALIGN(4);
-	.u_boot_list : {
-		KEEP(*(SORT(.u_boot_list*)));
-	}
-
-	. = ALIGN (4);
-
-	.image_copy_end :
-	{
-		*(.__image_copy_end)
-	}
-
-	.rel_dyn_start :
-	{
-		*(.__rel_dyn_start)
-	}
-
-	.rel.dyn : {
-		*(.rel*)
-	}
-
-	.rel_dyn_end :
-	{
-		*(.__rel_dyn_end)
-	}
-
-	_end = .;
-
-/*
- * Compiler-generated __bss_start and __bss_end, see arch/arm/lib/bss.c
- * __bss_base and __bss_limit are for linker only (overlay ordering)
- */
-
-	.bss_start __rel_dyn_start (OVERLAY) : {
-		KEEP(*(.__bss_start));
-		__bss_base = .;
-	}
-
-	.bss __bss_base (OVERLAY) : {
-		*(.bss*)
-		 . = ALIGN(4);
-		 __bss_limit = .;
-	}
-	.bss_end __bss_limit (OVERLAY) : {
-		KEEP(*(.__bss_end));
-	}
-
-	.dynsym _end : { *(.dynsym) }
-	.dynbss : { *(.dynbss) }
-	.dynstr : { *(.dynstr*) }
-	.dynamic : { *(.dynamic*) }
-	.hash : { *(.hash*) }
-	.plt : { *(.plt*) }
-	.interp : { *(.interp*) }
-	.gnu : { *(.gnu*) }
-	.ARM.exidx : { *(.ARM.exidx*) }
-}